Bedienungsanleitung RAD Data comm ASMi-52

186 Seiten 3.91 mb
Download

Zur Seite of 186

Summary
  • RAD Data comm ASMi-52 - page 1

    Installation and Operation Manual AS M i - 5 2 2 /4-Wire SHDSL Modem Version 2.5 ...

  • RAD Data comm ASMi-52 - page 2

    ...

  • RAD Data comm ASMi-52 - page 3

    ASMi-52 Version 2.5 2/4-Wire SHDSL Modem Installation and Operation Manual Notice T h i s m a n u a l c o n t a i n s i n f o r m a t i o n t h a t i s p r o p r i e t a r y t o R A D D a t a C o m m u n i c a t i o n s L t d . ( " R A D " ) . N o part of this publication may be reproduced in any form whatsoever without prior written appr ...

  • RAD Data comm ASMi-52 - page 4

    Limited Warranty RAD warrants to DISTRIBUTOR that the hardware in the A SMi- 52 to be de livered hereunder s hall be free of defects in material and workmanshi p under no rmal use and service for a period of twelve (12) months following the date of shipment to DISTRIBUTOR. If, during the warranty period, any component part of the equipment becomes ...

  • RAD Data comm ASMi-52 - page 5

    General Safety Instructions The following in structions ser ve as a general guid e for the safe installation and op eration of telecommunications products. Addition al i nstructions, if appl icable, are included ins ide the manual. Safety Symbols This symbol may appear on the equipment or in the text. It indicates potential safety hazards regarding ...

  • RAD Data comm ASMi-52 - page 6

    Handling Energized Products General Safety Practices Do not touch or tamper with the power supply when the power cord is connecte d. Line voltages may be present inside certain product s even wh en the power switch (if installed) is in the OFF position or a fuse is blown. For DC-powered products, alth ough the voltages levels are usua lly not hazar ...

  • RAD Data comm ASMi-52 - page 7

    Connection of Data and Telecommunications Cables Data and telecommunicatio n interfaces are classified accor ding to their safety status. The following table list s the status of several standard in terfaces. If the st atus of a given port differs from the standard one, a no tice will be given i n the manual. Ports Safety Status V.11, V.28, V.35, V ...

  • RAD Data comm ASMi-52 - page 8

    To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 AWG ou de section supérieure. Some ports are suitable for connection to intra-buildin g or non-exposed wiring or cabling only. In such cases, a notice will be ...

  • RAD Data comm ASMi-52 - page 9

    Canadian Emission Requirements This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numérique de la classe A respecte to utes les exigences du Règlement sur le matériel brouilleur du Canada. Warning per EN 55022 (CISPR- 22) This is a class A product. In a domestic envir ...

  • RAD Data comm ASMi-52 - page 10

    Declaration of Conformity Manufacturer's Name: RAD Data Communications Ltd. Manufacturer's Address: 24 Raoul Wallenberg St. Tel Aviv 69719 Israel declares that the product: Product Name: ASMi-52 Conforms to the following standard(s ) or other normative document(s): EMC: EN 55022: 1994 Limits and methods of measurement of radio disturbance ...

  • RAD Data comm ASMi-52 - page 11

    ASMi-52 Ver. 2.5 Configuring ASMi-52 1 Quick Start Guide Installation of ASMi-52 should be carried out only by an experienced technician. If you are familiar with ASMi-52, use this gu ide to prepare the units for operation. 1. Installing ASMi-52 Connecting the Interfaces 1. Connect the line to the RJ-45 re ar panel connector dedicated SHDSL. 2. Con ...

  • RAD Data comm ASMi-52 - page 12

    Quick Start Guide Installation and Operation Manual 2 Configuring ASMi-52 ASMi-52 Ver. 2.5 Configuring the Master Cloc k  To configure the master clock: • From the System Configuration menu (Main Menu > Configurat ion > System Configuration > Ma ster Clock), configure the central ASMi-52 clock to external or internal and remote AS Mi- ...

  • RAD Data comm ASMi-52 - page 13

    Installation and Operation Manual Quick Start Guide ASMi-52 Ver. 2.5 Configuring ASMi-52 3  To configure E1 parameters: • From the E1 Port Configuration menu (Main Menu > Configuration > Port Configuration > E1 Port Configuration), configure the following E1 parameters:  Framing mode  Timeslot assignment • You can configure ti ...

  • RAD Data comm ASMi-52 - page 14

    Quick Start Guide Installation and Operation Manual 4 Configuring ASMi-52 ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 15

    ASMi-52 Installation and Operation Manual i Contents Chapter 1. Introduction 1.1 Overview ..................................................................................................................... 1-1 Versio ns ....................................................................................................................... ........ ...

  • RAD Data comm ASMi-52 - page 16

    Table of Contents ii ASMi-52 Installation and Operation Manual Setting the G.704 Interfac e Type ......................................................................................... 4-21 4.3 Configuring the Physical P orts .................................................................................... 4-22 Configuring the SH DSL Interface ...

  • RAD Data comm ASMi-52 - page 17

    ASMi-52 Ver. 2.5 Overview 1-1 Chapter 1 Introduction 1.1 Overview ASMi-52 is an SHDSL mo dem that operates in full- duplex over 2/4-wire lines an d offers a cost-effective solution for delivering digital data to customer pre mises over existing copper cables. AS Mi-52 handl es multiple data rates in the range of 64–4608 kbps. The unit is availabl ...

  • RAD Data comm ASMi-52 - page 18

    Chapter 1 Introduction Installation and Operation Manual 1-2 Overview ASMi-52 Ver. 2.5 Unit Enclosure ASMi-52 is available in a plastic, metal, or rail-mount enclosure. Applications Figure 1-1 illustrates a typ ical ASMi-52 application, in which standalone modems operate opposite each other. Figure 1-2 shows ASMi- 52 units operating op posite a cen ...

  • RAD Data comm ASMi-52 - page 19

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Overview 1-3 Figure 1-2. ASMi-52 Mo dems Operating O pposite a Centrall y Located LRS-24 Rack Figure 1-3. ASMi-5 2 Modems Op erating opposite ASMi-52CD Cards ...

  • RAD Data comm ASMi-52 - page 20

    Chapter 1 Introduction Installation and Operation Manual 1-4 Overview ASMi-52 Ver. 2.5 Features Functionality ASMi-52 can be configured to operate in a CO (central office) or CPE (custo mer premises equipment) mode. Line Interface ASMi-52 extends the ran ge of data transmission ov er 2/4-wire lines up to 7.0 km (4.3 miles), by employing SHDSL TC-P ...

  • RAD Data comm ASMi-52 - page 21

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Overview 1-5 DTE Interface ASMi-52 supports the following DTE interfaces: • X.21 • V.35 • RS-530 • E1, as per G.704 • T1 • Ethernet/Fast Ethernet bridge with VLAN support (combined with man agement LAN port) • IR-IP (IP router). When ASMi-52 is ordere d only wit ...

  • RAD Data comm ASMi-52 - page 22

    Chapter 1 Introduction Installation and Operation Manual 1-6 Overview ASMi-52 Ver. 2.5 Table 1-2. ASMi-52 D ata Rates DTE Interface and Clock Mode Line Interface Local ASMi-52 Remote ASMi-52 2-wire 4-wire Serial DTE interface, internal clock Serial DTE interface n × 64 kbps (n = 1, 2, … 32, 36) n × 128 kbps ( n = 1, 2, …32, 36) Serial DTE int ...

  • RAD Data comm ASMi-52 - page 23

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Overview 1-7 Multiplexer Applications • The multiplexer unit cannot be configured as a device with L AN only port. It must have a DTE or IR port. • The hardware of a single unit-based pr oduct with a LAN port ma nager is different from that of a mu ltiplexer-based product ...

  • RAD Data comm ASMi-52 - page 24

    Chapter 1 Introduction Installation and Operation Manual 1-8 Overview ASMi-52 Ver. 2.5 Table 1-4. Possible Mu ltiplexer Applications (Cont.) CO/CPE E1 Serial DTE LAN E1+Serial DTE E1+LAN Serial DTE+LAN E1 ↔ E1 E1 ↔ Serial DTE E1 ↔ LAN E1 ↔ E1+Serial DTE E1 ↔ E1 E1 ↔ Serial DTE E1+LAN ↔ E1 E1 ↔ E1 E1 ↔ Serial DTE E1 ↔ E1+LAN E1 ? ...

  • RAD Data comm ASMi-52 - page 25

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Overview 1-9 • Receive, recovered from the received line signal (CPE mode). Management ASMi-52 supports the following management options: • ASCII terminal or Easy Config hand-hel d device via V.24/RS-232 terminal port • Telnet via a dedicated 10/100BaseT port • SNMP n ...

  • RAD Data comm ASMi-52 - page 26

    Chapter 1 Introduction Installation and Operation Manual 1-10 Functional Description ASMi-52 Ver. 2.5 Statistics Collection ASMi-52 supports SHDSL and E1/T1 statistics collection. Alarm Reporting ASMi-52 alarms are relayed via a dedi cated 6-pin terminal block connector. SHDSL Repeaters Up to eight SHDSL repeaters can be installed in l ine to incre ...

  • RAD Data comm ASMi-52 - page 27

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Functional Description 1-11 Modem Glue Logi c Data & Clock LED s an d T erm i na l I nt er fa c e Con trol S ignal s CPU 10/ 100B as eT Ma nage ment Por t CPU Data Bus DTE Interfa ce SHDSL Li ne I nt erf ac e Power Supp ly Internal Oscill ator Figure 1-5. ASMi-52/ 4W with ...

  • RAD Data comm ASMi-52 - page 28

    Chapter 1 Introduction Installation and Operation Manual 1-12 Technical Specifications ASMi-52 Ver. 2.5 Internal oscillator – Serves as a source of internal clock for the ASMi-52 unit. Modem glue logic module – Processes the data from/to the SH DSL interface module. SHDSL line interface – Translates the received and transmitted data from the ...

  • RAD Data comm ASMi-52 - page 29

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Technical Specifications 1-13 • T1: 100 Ω , balanced Connector Type • X.21: 15-pin, D-type, female • V.35 – 34-pin, female • RS-530 – 25-pin, D-type, female • G.70 3/G.704 E1 – RJ-45, balanced or unbalanced ( via adapter cable) • T1 – RJ-45 • IR-IP ( I ...

  • RAD Data comm ASMi-52 - page 30

    Chapter 1 Introduction Installation and Operation Manual 1-14 Technical Specifications ASMi-52 Ver. 2.5 Alarm Relay Operation Normally Open and Normally Closed, using different pins Connector Terminal block, 6-pin Indicators PWR (green) Power TEST (red) Test SYNC A/B (green/red) Synchronization of DSL line DATA (yellow) Data Transfer (except E1 and ...

  • RAD Data comm ASMi-52 - page 31

    Installation and Operation Manual Chapter 1 Introduction ASMi-52 Ver. 2.5 Technical Specifications 1-15 Environment Temperature Standalone: 0 ° to 50 ° C (32 ° to 122 ° F) Rail-mount: − 20 ° to 70 ° C ( − 4 ° to 158 ° F) Humidity Up to 90%, non–condensing Shock (Rail-Mount) IEC 60068-2-27 shock 1 5g, 11 ms duration, 18 shocks Vibratio ...

  • RAD Data comm ASMi-52 - page 32

    Chapter 1 Introduction Installation and Operation Manual 1-16 Technical Specifications ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 33

    ASMi-52 Ver. 2.5 Site Requi rements and Prerequisites 2-1 Chapter 2 Installation and Setup 2.1 Introduction This chapter describes installation and setup procedures for the standalone ASMi-52 modem. After installing the unit: • Refer to Chapter 3 for the operating instructions. • Refer to Chapter 4 for the detailed system conf igura tion proced ...

  • RAD Data comm ASMi-52 - page 34

    Chapter 2 Installation and Setup Installation and Operation Manual 2-2 Connecting the Interface Cables ASMi-52 Ver. 2.5 Allow at least 90 cm (36 in) of fronta l clearance for operation and maintenance accessibility. Allow at least 10 cm (4 in) cl earance at the rear of the unit for signal lines and interface cables. The ambient operating temperatur ...

  • RAD Data comm ASMi-52 - page 35

    Installation and Operation Manual Chapter 2 Installation and Setup ASMi-52 Ver. 2.5 Connecting the Power Cables 2-3 Connecting the Line The ASMi-52 line interface terminates in an 8-pin RJ-45 connector.  To connect the line connector: • Connect the line cable to the RJ -45 connector designated SHDSL. Connecting the DTE Interface The ASMi-52 DT ...

  • RAD Data comm ASMi-52 - page 36

    Chapter 2 Installation and Setup Installation and Operation Manual 2-4 Connecting the Power Cables ASMi-52 Ver. 2.5 Before connecting this unit to a powe r source and connecting or disconnecting any other cable, the protective earth terminals of this unit must be conn ected to the protective ground conductor of the mains (AC or DC) power cord. If y ...

  • RAD Data comm ASMi-52 - page 37

    ASMi-52 Ver. 2.5 Controls and Indicators 3-1 Chapter 3 Operation This chapter provides the following information for the ASMi-52 modem: • ASMi-52 front-panel indicators • Operating procedures (turn-on, fron t-panel indications, performance monitoring and turn-off) • ASMi-52 default settings. Installation procedures giv en in Chapter 2 mu st b ...

  • RAD Data comm ASMi-52 - page 38

    Chapter 3 Operation Installation and Operation Manual 3-2 Controls and Indicators ASMi-52 Ver. 2.5 ASMi-5 2 Figure 3-1. ASMi-52 Fr ont Panel, E1 Interface (2 Wire ) Figure 3-2. ASMi-52 Fr ont Panel, E1 Interface (4 Wire ) Figure 3-3. ASMi-52 Fr ont Panel, T1 Interface (4 Wir e) ASMi-5 2 Figure 3-4. ASMi-52 Front Panel, DTE Serial Interface (4 Wire) ...

  • RAD Data comm ASMi-52 - page 39

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Controls and Indicators 3-3 Table 3-1. ASMi-52 Front Panel LEDs Name Function PWR (green) On – Power is ON TST (red) On – A loopback test is active in a local or remote unit SYNC A (red/green) On (red) – Link A is not synchronized On (green) – Link A is synchronized Blin ...

  • RAD Data comm ASMi-52 - page 40

    Chapter 3 Operation Installation and Operation Manual 3-4 Default Settings ASMi-52 Ver. 2.5 3.3 Default Settings ASMi-52 is managed by an ASCII ter minal or a PC running a terminal emulation program via a menu-driv en embedded so ftware. Table 3-4 lists the default settings of the ASMi-52 conf iguration parameters. Table 3-4. Default Settings Param ...

  • RAD Data comm ASMi-52 - page 41

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Default Settings 3-5 Parameter Default Value Control Port Control port rate 9600 bps Data 8 Parity None Interface DCE CTS =RTS DSR ON Port control mode Terminal User name – Password 1234 Pop alarm OFF Security timeout 10 min Call Out Mode None Number of retries 1 Wait for conn ...

  • RAD Data comm ASMi-52 - page 42

    Chapter 3 Operation Installation and Operation Manual 3-6 Configuration Alternatives ASMi-52 Ver. 2.5 Parameter Default Value Serial DTE Interface Rate Single: 2-wire – 192 kbps 4-wire – 384 kbps Multiplexer: 1. E1+Serial DTE, N/A , 0 kbps 2. LAN+Serial DTE: 2-wire – 192 kbps 4-wire – 384 kbps LLB from DTE Disable RLB from DTE Disable E1/E1 ...

  • RAD Data comm ASMi-52 - page 43

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Configur ation Alternatives 3-7 • Remote management via out-of- band 10/1 00BaseT port or dedi cated timeslot. Remote management is p erformed us ing Telnet, or ConfiguR AD (RAD’s Web-based application), or RADvie w (RAD’s SNMP -based management system). Managing ASMi-52 v ...

  • RAD Data comm ASMi-52 - page 44

    Chapter 3 Operation Installation and Operation Manual 3-8 Configuration Alternatives ASMi-52 Ver. 2.5 3. Configure the terminal to the defa ult communication para meters: 9.6 kbps, one start bit, eight data bits, no parity, one stop bit, VT100 e mulation. 4. Select the full duplex mo de. 5. Turn the terminal echo off. 6. Disa ble any type of flow c ...

  • RAD Data comm ASMi-52 - page 45

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Configur ation Alternatives 3-9 Managing ASMi-52 via Ethernet Port ASMi-52 is equipped with an Etherne t/Fast Ethernet port (10/100BaseT) which enables communication with ASMi-52 management subs ystem using the IP protocol (see Figure 3-9 ). The Ethernet management port is confi ...

  • RAD Data comm ASMi-52 - page 46

    Chapter 3 Operation Installation and Operation Manual 3-10 Configuration Alternatives ASMi-52 Ver. 2.5 session over the dedicated timeslot ha s priority ove r management via the 10/100BaseT port. 1. Connect the E1/T1 line to the ASMi-52 E1 or T1 port. 2. Start a terminal management sess ion and do the following:  Assig n an IP address and an IP ...

  • RAD Data comm ASMi-52 - page 47

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Configur ation Alternatives 3-11 • Trace – opens an additional pane for s ystem messages, progress indicators (ping, software and co nfiguration fi le downloads) and alarms. It is recommended to keep the trace pane open all the time. • Refresh All – refreshes all screen ...

  • RAD Data comm ASMi-52 - page 48

    Chapter 3 Operation Installation and Operation Manual 3-12 Configuration Alternatives ASMi-52 Ver. 2.5 Figure 3-10. Inventory and Configurati on Menus ...

  • RAD Data comm ASMi-52 - page 49

    Installation and Operation Manual Chapter 3 Operation ASMi-52 Ver. 2.5 Configur ation Alternatives 3-13 Figure 3-11. Monitoring, Diagno stics and File Utilities Menus ...

  • RAD Data comm ASMi-52 - page 50

    Chapter 3 Operation Installation and Operation Manual 3-14 Turning Off ASMi-52 ASMi-52 Ver. 2.5 Logging Out  To end the current session: • In the Main m enu, click Logout or type & in a terminal management screen. • • ASMi-52 allo ws at least four management se ssions to be active at a time. If the Web-based management sessi ons were n ...

  • RAD Data comm ASMi-52 - page 51

    ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-1 Chapter 4 Configuration 4.1 Configuring ASMi-52 for Management The configuration of ASMi-52 is performed via a menu-dr iven embedded software, using a standard ASCII terminal or a PC running a terminal emulat ion application connected to the rear panel CONTROL port. Altern atively, ASMi-52 can ...

  • RAD Data comm ASMi-52 - page 52

    Chapter 4 Configuration Installation and Operation Manual 4-2 Configuring ASMi-52 for Management ASMi-52 Ver. 2.5 Entering Device Information The Device Information menu allows you to assign a name to ASMi-52, define its location, and contact person. These entries may include up to 20 characters.  To enter device information: 1. Display the Sys ...

  • RAD Data comm ASMi-52 - page 53

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-3 Configuring the Host Parameters ASMi-52 can be managed by a netw ork management station, w hich is located on the LAN connected to the 10/100BaseT po rt. In order to establish a pro per connection, it is necessary to configure the follo ...

  • RAD Data comm ASMi-52 - page 54

    Chapter 4 Configuration Installation and Operation Manual 4-4 Configuring ASMi-52 for Management ASMi-52 Ver. 2.5 3. Type a nu mber corresponding to a subnet mask of t he already defined network management station, and ente r a new value. 4. Repeat step 2 an d step 3 to defi ne addit ional management stations. 5. Press <Esc> to return to the ...

  • RAD Data comm ASMi-52 - page 55

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-5 ASMi-52 Management Access 1. TELNET allowed (access allowed) 2. WEB allowed (access allowed) > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-6. Mana gement Access Menu Configuring Dedicated Timeslots ASMi-52 units with a ...

  • RAD Data comm ASMi-52 - page 56

    Chapter 4 Configuration Installation and Operation Manual 4-6 Configuring ASMi-52 for Management ASMi-52 Ver. 2.5 ASMi-52 Rem Agent Table SOURCE IP DESTINATION IP PORT > ESC-prev. menu; !-main menu; &-exit; @-scroll; ?-help Figure 4-8. R em Agent Table Configuring VLAN Encapsulation ASMi-52 is occasionally connected to a VLAN network when ma ...

  • RAD Data comm ASMi-52 - page 57

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-7 Configuring the LAN Port ASMi-52 includes a 10/100BaseT port that can be used as a user or management port. The LAN port operates in a self-learning bridge or transparent mode, w ith or without autonegotiation. • If the LAN port serve ...

  • RAD Data comm ASMi-52 - page 58

    Chapter 4 Configuration Installation and Operation Manual 4-8 Configuring ASMi-52 for Management ASMi-52 Ver. 2.5 Filling out the Bridging Table When the 10/100BaseT port operates in the bridge mode, yo u can assign MAC addresses to the local or remote LAN.  To fill out the bridge table: 1. Select Bridging Table from the Local LAN Config uration ...

  • RAD Data comm ASMi-52 - page 59

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-9 ASMi-52 Bridge Table Type (Static) 1. MAC Address ... (00000000000) 2. Port ... () > ESC-prev. menu; !-main menu; &-exit; ?-help Figure 4-12. Bridge Table, Editing Mode Configuring Aging Timeout The aging time is the timeout peri ...

  • RAD Data comm ASMi-52 - page 60

    Chapter 4 Configuration Installation and Operation Manual 4-10 Configuring ASMi-52 for Management ASMi-52 Ver. 2.5 ASMi-52 QoS Mapping (Classification 802.1p) 1. User Priority 0 > (Traffic Class 0) 2. User Priority 1 > (Traffic Class 0) 3. User Priority 2 > (Traffic Class 0) 4. User Priority 3 > (Traffic Class 0) 5. User Priority 4 > ...

  • RAD Data comm ASMi-52 - page 61

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring ASMi-52 for Management 4-11 ASMi-52 Data Rate (2304 Kbps) 1. 64 Kbps 12. 768 Kbps 23. 1472 Kbps 2. 128 Kbps 13. 832 Kbps 24. 1536 Kbps 3. 192 Kbps 14. 896 Kbps 25. 1600 Kbps 4. 256 Kbps 15. 960 Kbps 26. 1664 Kbps 5. 320 Kbps 16. 1024 Kbps 27. 1728 Kbps 6. 384 Kbp ...

  • RAD Data comm ASMi-52 - page 62

    Chapter 4 Configuration Installation and Operation Manual 4-12 Configuring ASMi-52 System Parameters ASMi-52 Ver. 2.5 2. If the autonegotiation is e nabled, choose Max AutoNeg Capabil ity from the Local LAN Configuration menu. The Set Capability menu appears. 3. Select the required LAN operation mo de by choosing one o f the following:  10BaseT ...

  • RAD Data comm ASMi-52 - page 63

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring AS Mi-52 System Parameters 4-13 ASMi-52 Configuration > 1. System configuration > 2. LAN configuration > 3. SHDSL configuration 4. E1 configuration 5. T1 configuration 6. DTE configuration > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-1 ...

  • RAD Data comm ASMi-52 - page 64

    Chapter 4 Configuration Installation and Operation Manual 4-14 Configuring ASMi-52 System Parameters ASMi-52 Ver. 2.5 Configuring the Master Cloc k ASMi-52 modems support receive, exte rnal and internal clock modes. When configured to the internal or extern al clock, ASMi-52 modem operates as a n STU-C unit. When configured to the receive clock, AS ...

  • RAD Data comm ASMi-52 - page 65

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring AS Mi-52 System Parameters 4-15 ASMi-52 Local/Remote Card Mode 1. E1 2. DTE 3. E1 + LAN 4. E1 + V35 5. V35 + LAN > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-19. Local/Remote Card Mode Menu Configuring Remote Ca rd Mode The remote card mode con ...

  • RAD Data comm ASMi-52 - page 66

    Chapter 4 Configuration Installation and Operation Manual 4-16 Configuring ASMi-52 System Parameters ASMi-52 Ver. 2.5 Configuring Control Port Pa rameters The embedded ASMi-52 software enables you to c onfigure the Control port parameters.  To access the Control port menu: • From the System Configuration menu, select Control Port (Main menu &g ...

  • RAD Data comm ASMi-52 - page 67

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring AS Mi-52 System Parameters 4-17 Selecting the Contro l Por t Interfa ce  To select the control port interface: 1. From the Control Port menu, select Interface (Main menu > Configuration > System Configuration > Control Port > Interface) to choose t ...

  • RAD Data comm ASMi-52 - page 68

    Chapter 4 Configuration Installation and Operation Manual 4-18 Configuring ASMi-52 System Parameters ASMi-52 Ver. 2.5 ASMi-52 Port Control 1. Port Control Mode > (Terminal) 2. Terminal > 3. Dial out > 4. Save > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-22. Port Control Menu Configuring the Port Control Mode The Control ...

  • RAD Data comm ASMi-52 - page 69

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring AS Mi-52 System Parameters 4-19 ASMi-52 Terminal 1. Change access > 2. POP ALARM (No) 3. Security timeout (10 min) 4. Save > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-24. Terminal Menu  To change the user name and password: 1. From t he ...

  • RAD Data comm ASMi-52 - page 70

    Chapter 4 Configuration Installation and Operation Manual 4-20 Configuring ASMi-52 System Parameters ASMi-52 Ver. 2.5  To configure the security timeout: 1. From t he Terminal menu, select Security Timeout (Main menu > Configuration > System Configuratio n > Control Port > Port Control > Terminal > Security Timeout) to configur ...

  • RAD Data comm ASMi-52 - page 71

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring AS Mi-52 System Parameters 4-21  3 to specify the time (in sec) ASMi-52 waits for an answer after each dial ing attempt. If the called station does not answer within the specified time, ASMi-52 disconnects. If addition al call attempts are allowed, ASMi-52 red ...

  • RAD Data comm ASMi-52 - page 72

    Chapter 4 Configuration Installation and Operation Manual 4-22 Configuring the Physical Ports ASMi-52 Ver. 2.5 4.3 Configuring the Physical Ports Configuring the SHDSL Interface The ASMi-52 configuration soft ware allows you to c hange the modem’s transmission mode (A nnex A or Annex B). Examples given below illustrate the lo cal device configura ...

  • RAD Data comm ASMi-52 - page 73

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-23 ASMi-52 SHDSL remote port configuration Transmission mode (Annex_AB) Asym PSD (Asym/Sym Enable) Line prob (Adaptive rate) 1. Power backoff (Enable) 2. Snext margin (Disable Snext margin) 3. Current margin (Disable current margin) 4. Loop a ...

  • RAD Data comm ASMi-52 - page 74

    Chapter 4 Configuration Installation and Operation Manual 4-24 Configuring the Physical Ports ASMi-52 Ver. 2.5 2. Select the Snext margin by typing th e number corresponding to the required value. The SHDSL Remote Port menu appears. 3. Select Save to save the changes. ASMi-52 Snext margin (Disable Snext margin) 1. -10 12. 1 2. -9 13. 2 3. -8 14. 3 ...

  • RAD Data comm ASMi-52 - page 75

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-25 Configuring the Power Spectral Density By configuring the power spectral dens ity, you define the amoun t of power applied to the spectrum of frequencies that carry the informat ion signal in order to achieve a satisfactory level of signal ...

  • RAD Data comm ASMi-52 - page 76

    Chapter 4 Configuration Installation and Operation Manual 4-26 Configuring the Physical Ports ASMi-52 Ver. 2.5 Configuration > SHDSL Local Port/SHDSL Remote Port/SHDSL Repeater > Loop Attenuation Threshold). The loop attenuation threshold can be configured from the SHDSL remote or local port, or from the SHDSL repeater. 2. Enter the required ...

  • RAD Data comm ASMi-52 - page 77

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-27 Configuring the DTE Interface Data Rate ASMi-52 supports multiple data rate s between the range of 64 kbps and 4608 kbps, depending on the clock mode and line/DTE interface of the local and remote units (see Table 1-2 an d Table 1-3 ).  ...

  • RAD Data comm ASMi-52 - page 78

    Chapter 4 Configuration Installation and Operation Manual 4-28 Configuring the Physical Ports ASMi-52 Ver. 2.5 Configuring the E1 Interface The following are commonly used acronyms: • CO – Central Office, where the clock sour ce is set to internal or external • CPE – customer premise equipment. When ASMi-52 includes a G.7 04 E1 port, you ca ...

  • RAD Data comm ASMi-52 - page 79

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-29 ASMi-52 E1 Local Port 1. Framed mode (G732N) 2. Sync mode (CCITT(complies with G732)) 3. CRC-4 (NO) 4. Idle code (ff) 5. Time slots assign 6. Unit Identical Set (Yes) 7. Number TS for remote E1 8. Save > ESC-prev. menu; !-main menu; &am ...

  • RAD Data comm ASMi-52 - page 80

    Chapter 4 Configuration Installation and Operation Manual 4-30 Configuring the Physical Ports ASMi-52 Ver. 2.5 ASMi-52 Framed mode (Unframed) 1. Unframed 2. G732N 3. G732S transparent > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-34. Framed Mode Menu Enabling CRC-4 Code Generation You have to enable the CRC-4 code generation if yo ...

  • RAD Data comm ASMi-52 - page 81

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-31 ASMi-52 Sync mode (CCITT (complies with G732)) 1. FAST (after 1 sec) 2. 62411 (after 10 sec) 3. CCITT (complies with G732) > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-35. Sync Mode Menu Defining Idle Code You can define ...

  • RAD Data comm ASMi-52 - page 82

    Chapter 4 Configuration Installation and Operation Manual 4-32 Configuring the Physical Ports ASMi-52 Ver. 2.5 • • You can configure timeslot 0 to be looped or transp arent:  Looped – timeslot 0 is sent back to the E1 interface, when operating opposite remote units with a serial data interface.  Transparent – timeslot 0 is tran smitte ...

  • RAD Data comm ASMi-52 - page 83

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-33 ASMi-52 has a multiplexer mo dem with two interfa ces. The maximum timeslots that can be used are as follows: • If E1 + LAN, then the maximum TSs (t imeslots) = (2048 kbps – LAN rate) / 64 kbps. • If E1 + Serial DTE, then t he maximu ...

  • RAD Data comm ASMi-52 - page 84

    Chapter 4 Configuration Installation and Operation Manual 4-34 Configuring the Physical Ports ASMi-52 Ver. 2.5 • The Unit Identical Set is permanently set to Yes, the parameters are copied to the remote unit. If the Frame Mode is not G732S: • The Unit Identical setting can be set to Yes or No when the local modem is configured as CO and both mo ...

  • RAD Data comm ASMi-52 - page 85

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 Configuring the Physical Ports 4-35 • Transmit signal mask (DSU mode) – le ng th of a cable in feet between the ASMi-52 T1 port connector and the n etwork access point:  0 fe et – 0 to 133 feet  13 3 feet – 133 to 266 feet  26 6 feet - 266 to 399 feet  39 ...

  • RAD Data comm ASMi-52 - page 86

    Chapter 4 Configuration Installation and Operation Manual 4-36 Additional Tasks ASMi-52 Ver. 2.5 4.4 Additional Tasks Displaying the ASMi-52 Status The ASMi-52 software allows you to disp lay the modem system and physical port information. The status information is a vailable via the Monitoring menu.  To access the Monitoring menu: • From the ...

  • RAD Data comm ASMi-52 - page 87

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-37 ASMi-52 System Status Local Remote Device Type (ASMi52_SA_M (PLASTIC)-STU_C-2W) ASMi52_SA Clock Source (INT) RCV Software Version (2.01E24) (2.01E24) Hardware Version (0.00) (0.00) FPGA Version (0.13) (0.13) Hardware Status (NO HARDWARE FAILURE) (NO HW ...

  • RAD Data comm ASMi-52 - page 88

    Chapter 4 Configuration Installation and Operation Manual 4-38 Additional Tasks ASMi-52 Ver. 2.5 • The physical port alarms are described in Chapter 5 . 2. Type N to display the next page. Accessing the Remote ASMi-52 Accessing the remote ASMi-52 is performe d using a virtual connection with your terminal physically connected to the local unit. ? ...

  • RAD Data comm ASMi-52 - page 89

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-39 Figure 4-42. Password Reques t Screen (ConfiguRAD Session)  To enter the user name and password: 1. Type in your user name a nd press <Tab> . • You can leave the user name field empty (default), the default password is 12 34. 2. Type in your ...

  • RAD Data comm ASMi-52 - page 90

    Chapter 4 Configuration Installation and Operation Manual 4-40 Additional Tasks ASMi-52 Ver. 2.5 Figure 4-44. Main Menu (ConfiguRAD Session) Displaying the ASMi-52 Inventory The ASMi-52 inventory displays in formation on the functional blocks of the local or remote modem. ASMi-52 consists of the following components: • SHDSL unit • DTE unit • ...

  • RAD Data comm ASMi-52 - page 91

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-41 ASMi-52 Inventory 1 Index 1001 Description RAD-local ASMi-52_M SHDSL modem Vendor type Contained in 0 Class 3 Rel pos 0 Name SHDSL modem HW ver 0.00 SW ver 1.00E54 ->> > ESC-prev. menu; !-main menu; &-exit; @-scroll; ?-help Figure 4-45. In ...

  • RAD Data comm ASMi-52 - page 92

    Chapter 4 Configuration Installation and Operation Manual 4-42 Additional Tasks ASMi-52 Ver. 2.5 ASMi-52 TFTP TFTP status (No operation) TFTP error (No error) 1. TFTP IP server (172.17.160.103) 2. TFTP file name (201e24.img) 3. TFTP retry timeout (sec) [0-300] (15) 4. TFTP total timeout (sec) [0-4000] (1200) 5. Save 6. Transfer command > ESC - p ...

  • RAD Data comm ASMi-52 - page 93

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-43 For exit press Q(uit) If you press <Q> , ASMi-52 aborts the download process and displays Download failure. Press Esc to continue. message in addition to the previous display. • During the software installation, the TST in dicator blinks. 2. Se ...

  • RAD Data comm ASMi-52 - page 94

    Chapter 4 Configuration Installation and Operation Manual 4-44 Additional Tasks ASMi-52 Ver. 2.5 5. From the TFTP menu, pe rform the foll owing steps:  Select TFTP IP Server and enter the IP address of the TFTP server  Select TFTP File N ame and enter the name of the software file (for example, 201e24.img ).  Select TFTP Retry Timeo ut and ...

  • RAD Data comm ASMi-52 - page 95

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-45 ASMi-52 SW files Local Remote Software active version: (2.01E24) (2.02000) Software active partition: (0) (0) Code size: (813110) (813161) Date: (28-7-4) (2-8-4) Software backup version: (2.01E24) (2.01E11) Software backup partition: (1) (1) Code size: ...

  • RAD Data comm ASMi-52 - page 96

    Chapter 4 Configuration Installation and Operation Manual 4-46 Additional Tasks ASMi-52 Ver. 2.5 Resetting to Default Settings You can reset the local or remote ASMi-52 to it s default settings. Resetting to the factory default does not affect the master clock setting. In addition, you can reset the local ASMi-52 without affecting it s ma nagement ...

  • RAD Data comm ASMi-52 - page 97

    Installation and Operation Manual Chapter 4 Configuration ASMi-52 Ver. 2.5 A dditional Tasks 4-47 2. From th e Reset menu, select Local Reset to reset the local modem or Remo te Reset to reset the remote device. The Local/Remote Reset menu appears (see Figure 4-51 ). 3. From the Local/Remote Reset menu, select Local/Remote Device Reset to perform t ...

  • RAD Data comm ASMi-52 - page 98

    Chapter 4 Configuration Installation and Operation Manual 4-48 Additional Tasks ASMi-52 Ver. 2.5 ASMi-52 Repeater Reset 1. Repeater SHDSL line reset . . . 2. Repeater number > (1) > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 4-52. Repeater Reset Menu Exiting the Control Session You can exit the terminal control session any time ...

  • RAD Data comm ASMi-52 - page 99

    ASMi-52 Ver. 2.5 Overview 5-1 Chapter 5 Configuring a Typical Application 5.1 Overview This chapter provides detailed instr uctions for setting up t wo ASMi-52 modems i n a typical application. ASMi-52 configuration is performed via a men u-driven embedded software using a standard ASCII terminal or a PC r unning a terminal emulatio n application c ...

  • RAD Data comm ASMi-52 - page 100

    Chapter 5 Configuring a Typical Ap plication Installation and Operation Manual 5-2 Configuring the ASMi-52 units ASMi-52 Ver. 2.5 5.2 Configuring the ASMi-52 units Two ASMi-52 units must be configured for this app lication. Both units have t he same configuration parameters, except for the host IP address and the master clock mode.  To prepare a ...

  • RAD Data comm ASMi-52 - page 101

    Installation and Operation Manual Chapter 5 Configuring a Typical Application ASMi-52 Ver. 2.5 Configur ing the ASMi-52 units 5-3  Set the CO ASMi- 52 unit clock to Internal.  Set the CPE ASMi-52 unit clock to Receive. 3. Select Save to save the changes.  To set the device host IP address: 1. Displa y the host IP menu (Mai n menu > Conf ...

  • RAD Data comm ASMi-52 - page 102

    Chapter 5 Configuring a Typical Ap plication Installation and Operation Manual 5-4 Configuring the ASMi-52 units ASMi-52 Ver. 2.5 2. From t he Framed Mode menu, select Unframed to choose the unframed operation. The E1 Local Port menu appears. 3. Save the changes. After performing these config uration proc edures, the ASMi-52 units are ready to be c ...

  • RAD Data comm ASMi-52 - page 103

    Installation and Operation Manual Chapter 5 Configuring a Typical Application ASMi-52 Ver. 2.5 Configur ing the ASMi-52 units 5-5 ASMi-52 DTE local port configuration > 1. LLB from DTE : (Enable/Disable) 2. RLB from DTE : (Enable/Disable) 3. Data rate : (1984 kbps) 4. Save > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 5-6. DTE Lo ...

  • RAD Data comm ASMi-52 - page 104

    Chapter 5 Configuring a Typical Ap plication Installation and Operation Manual 5-6 Configuring the ASMi-52 units ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 105

    ASMi-52 Ver. 2.5 Monitoring Performance 6-1 Chapter 6 Troubleshooting and Diagnostics This chapter describes the ASMi- 52 di agnostic funct ions, which include: • Status indications, alarms, power-up self-test • Statistics collection • Bit Error Rate Test (BERT) • Diagnostic tests (loopback s and LEDs test). 6.1 Monitoring Performance Displ ...

  • RAD Data comm ASMi-52 - page 106

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-2 Monitoring Performance ASMi-52 Ver. 2.5 2. From th e Physical Port Statistics menu, select SHDSL Port Performances to display the unit’s SDHSL statistics. The SDHSL Port Performances menu appears (see Figure 6- 2 ). ASMi-52 SHDSL Port Performances 1. SHDSL current per ...

  • RAD Data comm ASMi-52 - page 107

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Monitoring Performance 6-3 ASMi-52 SHDSL current day performances Local A Local B Remote A Remote B Port number (1) (1) (1) (1) 24 hour ES (1) (1) (1) (1) 24 hour UAS (1401) (1401) (1401) (1401) 24 hour SES (0) (0) (0) (0) 24 hour LOWS (0) (0) (0) (0) 24 ho ...

  • RAD Data comm ASMi-52 - page 108

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-4 Monitoring Performance ASMi-52 Ver. 2.5 ASMi-52 SHDSL all intervals local/remote performances ... Line A Line B INT CRC LOSWS ES SES UAS CRC LOSWS ES SES UAS ESC-prev. menu; !-main menu; &-exit; ?-help; @-scroll Figure 6-5. S HDSL All Interv als Local/Remote Perform ...

  • RAD Data comm ASMi-52 - page 109

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Monitoring Performance 6-5 • For details on enabling th e CRC-4 function, refer to Chapter 4 . • For the details on configur ing T1 fr aming, refer to Configuring T1 I nterface in Chapter 4. Displaying the Current E1/T1 Statistics  To display the cur ...

  • RAD Data comm ASMi-52 - page 110

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-6 Monitoring Performance ASMi-52 Ver. 2.5 ASMi-52 E1/T1 current day performance Local Remote Port number (1) No statistics collection ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 6-9. E1/T1 Current Day Performances Screen Table 6-2. E1/T1 Statistic s Parameter ...

  • RAD Data comm ASMi-52 - page 111

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Monitoring Performance 6-7 Table 6-2. . E1 Statistics Parameters (C ont.) Display Description Range Current DM Number of degraded minutes in which the B ER exceeded 1 × 10 -6 . This value is updated every minute for 15-m inute interval or every 24 hours fo ...

  • RAD Data comm ASMi-52 - page 112

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-8 Handling Alarms ASMi-52 Ver. 2.5 Clearing the E1/T1 Statistics  To clear E1/T1 statistics: • From the E1 Port Performances menu (see Figure 6-2 ), select E1 /T1 Clear Local Performances or E1 /T1 Clear Remote Performances (Main menu > Monitoring > Physical Po ...

  • RAD Data comm ASMi-52 - page 113

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Handling Alarms 6-9 Displaying All Alarms ASMi-52 allows you to displa y all alarms, irrespective of their origin (system or port).  To display all alarms: 1. From the Main menu, select Monitoring . The Monitoring menu appears (see Figure 6-11 ). 2. From ...

  • RAD Data comm ASMi-52 - page 114

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-10 Handling Alarms ASMi-52 Ver. 2.5 ASMi-52 System Monitoring 1. System status 2. System log file 3. System clear log file ... > ESC-prev.menu; !-main menu; &-exit; @-scroll Figure 6-13. System Moni toring Menu Working with the System Log File ASMi-52 maintains sys ...

  • RAD Data comm ASMi-52 - page 115

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Handling Alarms 6-11 ASMi-52 Physical port status Port Number (1) 1. Port status 2. Line mask (NO_MASK) 3. Port log file 4. Port clear log file > ESC-prev. menu; !-main menu; &-exit; @-scroll Figure 6-14. Physical Port Status Menu Masking Port Alarms ...

  • RAD Data comm ASMi-52 - page 116

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-12 Handling Alarms ASMi-52 Ver. 2.5 Table 6-3. ASMi-52 Alarms and Warn ings (Cont.) Number Terminal Message Port Description Severity 12 SNR MARGIN OVER LINE B SHDSL Line B signal-to-noise margin has exceeded the alarm threshold (4-wire units only) Minor 13 LOSW FAILURE O ...

  • RAD Data comm ASMi-52 - page 117

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Handling Alarms 6-13 Table 6-3. ASMi-52 Alarms and Warn ings (Cont.) Number Terminal Message Port Description Severity 32 E1 EXCESIVE ERR RATIO T1 EXCESIVE ERR RATIO DTE The bit error rate of the link exceed s 10 -3 Major 33 E1 AIS OCCURED T1 AIS OCCURED DT ...

  • RAD Data comm ASMi-52 - page 118

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-14 Handling Alarms ASMi-52 Ver. 2.5 Table 6-3. ASMi-52 Alarms and Warn ings (Cont.) Number Terminal Message Port Description Severity 45 LOOP ATTN. OVER CUSTOMER SIDE SHDSL Loop attenuation at the customer side of the repeater has exceeded the alarm threshold. Major (all) ...

  • RAD Data comm ASMi-52 - page 119

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Troubleshooting 6-15 Table 6-4. ASMi-52 Events Terminal Message Description CRC EVENT LINE A CRC errors are detected on line A CRC EVENT LINE B CRC errors are detected on line B SW DOWNLOAD FAIL Software download failed BUFFER OVERFLOW More than 100 entries ...

  • RAD Data comm ASMi-52 - page 120

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-16 Testing ASMi-52 ASMi-52 Ver. 2.5 ASMI 52 Port log file Source Name Severity Status Time 1. Local MNGMNT IS DOWN MAJOR ON 0:00:00 2. Local E1 SYNC LOSS LINE A MAJOR ON 0:00:00 3. Local E1 SIGNAL LOSS MAJOR ON 0:00:00 4. Local SYNC LOSS LINE A MAJOR ON 0:00:00 5. Local E ...

  • RAD Data comm ASMi-52 - page 121

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Testing ASMi-52 6-17 Bit Error Rate Test (BERT) It is possible to generate BERT+RLB or BERT (from both CO and CPE) in multiplexer and E1 and DTE Serial single units. The BERT, RLB + BERT can be set o nly if there is a connection to the FE unit. BERT Pattern ...

  • RAD Data comm ASMi-52 - page 122

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-18 Testing ASMi-52 ASMi-52 Ver. 2.5 ASMi-52 Bert 1. Bert (ON/OFF) 2. Bert + RLB (ON/OFF) 3. Bert pattern > 4. Save Bert parameters > ESC-prev. menu ; !–main menu ; &–exit terminal Figure 6-16. BERT Menu 3. From the Ber t menu, select Bert Pattern (see Figure ...

  • RAD Data comm ASMi-52 - page 123

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Testing ASMi-52 6-19 ASMi-52 Bert Results Local Remote Run time (seconds) 2000 Sync loss state sync loss Sync run time (seconds) 2000 Sync loss counter 2000 Total bits 3000 Error bits 50 BER 5.5E-4 > ESC-prev. menu; !–main menu ; &–exit terminal ...

  • RAD Data comm ASMi-52 - page 124

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-20 Testing ASMi-52 ASMi-52 Ver. 2.5 Figure 6-20. Loopback with Multiplexer Units Running the Local Loopback The local loopback (LLB) checks the pe rformance of the local ASMi-52 modem, the local DTE and the connection between them (see Figure 6-21 ). The LLB can be perfor ...

  • RAD Data comm ASMi-52 - page 125

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Testing ASMi-52 6-21  To run the local loopback: 1. From the Main menu, select Diagnost ics . The Diagnostics menu is displayed (see Figure 6-22 ). 2. From th e Diagnostics menu, select:  Local Test to run the LLB on the local ASMi-52  Remote Test ...

  • RAD Data comm ASMi-52 - page 126

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-22 Testing ASMi-52 ASMi-52 Ver. 2.5 Running the Remote Loopback The remote loopback (RLB) checks the performanc e of both the local and remote ASMi-52 modems, an d the li nes connecting them (see Figure 6-24 ). ASMi-52 allows you to set the loopbac k timeout causing the R ...

  • RAD Data comm ASMi-52 - page 127

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Testing ASMi-52 6-23  To activate the remote loopback at the SHDSL repeater : 1. From t he Diagnostics menu, select Repeater Test (Main menu > Diagnostics > Repeater Test). The Repeater Test menu appears (see Figure 6-26 ). 2. From the Repeater Tes ...

  • RAD Data comm ASMi-52 - page 128

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-24 Frequently Asked Questions ASMi-52 Ver. 2.5  To deactivate multiple loopbacks: • From the Local or Remote Test menu, select Clear All . The TST indicator turns off. Running the LEDs Test The user can perform the front-panel LED test to verify that the local unit i ...

  • RAD Data comm ASMi-52 - page 129

    Installation and Operation Manual Chapter 6 Troubleshooting and Diagnostics ASMi-52 Ver. 2.5 Technical Support 6-25 6.7 Technical Support Technical support for this product can be obtained from the local distrib utor from whom it was purchased. For further information, please contact th e RAD distributor nearest you or one of RAD's offices wor ...

  • RAD Data comm ASMi-52 - page 130

    Chapter 6 Troubleshooting and Diagnostics Installation and Operation Manual 6-26 Technical Support ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 131

    ASMi-52 Ver. 2.5 DTE Interface Connectors A-1 Appendix A Interface Connector Specifications A.1 DTE Interface Connectors V.35, X.21 and RS-530 Interface Connectors The V.35 interface of the ASMi-52 mo dem terminates in a 34 -pin female connector. The X.21 interface terminates in a 15-pin, D-t ype female connector. The RS-530 interface terminates in ...

  • RAD Data comm ASMi-52 - page 132

    Appendix A Interface Connector Specifications Installation and Operation Manual A-2 DTE Interface Connectors ASMi-52 Ver. 2.5 Table A-1. V.35, X.21 a nd RS-530 Connector Pinouts ( Cont.) V.35 RS-530 X.21 Description 34-Pin DB-25 DB-15 Signal Function Pin Circuit Pin Circui t Pin Circuit (Function) Data Set Ready E DSR 107 6 22 CC(A) CC(B) A posit i ...

  • RAD Data comm ASMi-52 - page 133

    Installation and Operation Manual Appendix A Interface Connector Specifications ASMi-52 Ver. 2.5 DTE Interface Connectors A-3 E1 and T1 Interface Connector The balanced E1 and T1 interfac es terminate in RJ-45 connector. Table A-2 lists the balanced connector pin assignment. Table A-2. E1/T1 Con nector Pinout Pin Function 1, 2 Transmit (output) 4, ...

  • RAD Data comm ASMi-52 - page 134

    Appendix A Interface Connector Specifications Installation and Operation Manual A-4 CONTROL Connector ASMi-52 Ver. 2.5 A.2 CONTROL Connector The control terminal interface terminates in a V. 24/RS-232 9-pin D-ty pe female connector that can be configured as DCE or DTE (see the Selecting the Control Port Interface section in Chapter 4). Ta ble A-4 l ...

  • RAD Data comm ASMi-52 - page 135

    Installation and Operation Manual Appendix A Interface Connector Specifications ASMi-52 Ver. 2.5 Alarm Relay Connector A-5 Table A-6. Cross Cab le Pinout DB-9 Pin DB-9 Pin 2 3 3 2 4 6 5 5 6 4 7 8 8 7 A.3 Alarm Relay Connector The ASMi-52 alarm relay terminates in a 6-pin female connector, designated ALARM. Figure A-1 lists the pino ut of the ALARM ...

  • RAD Data comm ASMi-52 - page 136

    Appendix A Interface Connector Specifications Installation and Operation Manual A-6 Alarm Relay Connector ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 137

    ASMi-52 Ver. 2.5 Introduction B-1 Appendix B IR-IP Interface Module B.1 Introduction Overview IR-IP is a high-performan ce, miniature IP router based on RAD's unique IP router chip, the Chip Router. IR-IP has a 10B aseT (UTP) interface and complies wit h IEEE 802.3. The router interface operates in either half-duplex or full-duplex mode. IR-IP ...

  • RAD Data comm ASMi-52 - page 138

    Appendix B IR-IP Interface Module Installation and Operation Manual B-2 Technical Specifications ASMi-52 Ver. 2.5 Application Figure B-1 shows a typ ical application of the ASMi-52 unit equipped with t he IR-IP interface module. Figure B-1. Typical Application of the ASMi-52 Unit with IR-IP B.2 Technical Specifications Router Local IP Net Capacity ...

  • RAD Data comm ASMi-52 - page 139

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Phys ical Description B-3 B.3 Physical Description Figure B-2 shows the rear panels of AS Mi-52 with the IR-IP interface module. CO NTRO L ALAR M LI NE B LI NE A 14 25 ACT LI NK A CT LI NK ER R SETUP 12 34 IR-IP E1/ T1 SHDS L TX RX 14 25 Figure B-2. IR-IP Ethernet ...

  • RAD Data comm ASMi-52 - page 140

    Appendix B IR-IP Interface Module Installation and Operation Manual B-4 Physical Descript ion ASMi-52 Ver. 2.5 IR-IP LEDs IR-IP contains three LEDs, which indicate the module activity. Table B-3 explains the functions of the IR-IP interface indicators. Table B-3. IR-IP Interface Indicators LED Name Function Color LINK Lights when the Ethernet inter ...

  • RAD Data comm ASMi-52 - page 141

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 IR-IP Management Subsystem B-5 B.4 IR-IP Management Subsystem The IR-IP interface modul e management subsystem sup ports the following functions: • Preliminary config uration • Configuration of management access parameters • Advanced configuration o f IR-IP p ...

  • RAD Data comm ASMi-52 - page 142

    Appendix B IR-IP Interface Module Installation and Operation Manual B-6 Performing Preliminary Configuration ASMi-52 Ver. 2.5 After configuring IR-IP, it starts normal operation and routes the traffic in accordance with the user-selec ted configuration parameters. To change the parameters of an already- configure d IR-IP, establish communication fr ...

  • RAD Data comm ASMi-52 - page 143

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Performing Preliminary Configuration B-7 Connecting the Telnet Host Before starting the management an d conf iguration activities, it is necessary t o establish IP commun ication between your Telnet host and the IR-IP interface module. For this purpose, it is neces ...

  • RAD Data comm ASMi-52 - page 144

    Appendix B IR-IP Interface Module Installation and Operation Manual B-8 Performing Preliminary Configuration ASMi-52 Ver. 2.5 To use the IP learning mechanism, you do not need to know the current address of IR-IP LAN interface, but only the prescribed IP address. The IP address is actually retrieved from the ARP frames sent during p inging to locat ...

  • RAD Data comm ASMi-52 - page 145

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 IR-IP Management Utility B-9 At this stage, the communication with IR-IP router is lost, because its IP ad dress has been changed. Therefore, you must re configure the destination IP address of the Telnet host. If you wish, yo u may also change t he temporary IP ad ...

  • RAD Data comm ASMi-52 - page 146

    Appendix B IR-IP Interface Module Installation and Operation Manual B-10 IR-IP Management Utility ASMi-52 Ver. 2.5 Starting a Management Utility The management utility i s started automatically when Telnet commun ication is established. If password protection is e nabled (see the Defining Management Access section below), you will be prompted to en ...

  • RAD Data comm ASMi-52 - page 147

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Quick Setup Guide B-11 B.7 Quick Setup Guide The Quick Setup menu is used to select th e main parameters’ values that m ust be defined before you start using IR-IP. Use the Advanced Setup menu (see the Advanced Setup section below) to specify values for other IR- ...

  • RAD Data comm ASMi-52 - page 148

    Appendix B IR-IP Interface Module Installation and Operation Manual B-12 Quick Setup Guide ASMi-52 Ver. 2.5 WAN IP Address – Used to enter the IP address for the IR-IP WAN interface, i.e., the IP address to be used by IP hosts on the WAN to reach this IR-IP interface module. If the WAN IP Address field remains blank, IR-IP operates in the Unnumbe ...

  • RAD Data comm ASMi-52 - page 149

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Quick Setup Guide B-13 ASMi-52 wi th IR-IP LAN IP A ddr es s: 192 .1 68 .1.2 Mask : 25 5.25 5. 25 5.248 DHCP Serv er IP Networ k Figure B-7. Selecting t he IP Subnet Mask Leaving the DHCP Server IP Address fi eld bla nk disables the DHCP re lay. 3. Set the protocol ...

  • RAD Data comm ASMi-52 - page 150

    Appendix B IR-IP Interface Module Installation and Operation Manual B-14 Defining Management Access ASMi-52 Ver. 2.5 B.8 Defining Management Access The Management Access menu is used to enable the use of passwords to protect the access to IR-IP management utility, and control the inactivity time-out interval. When password protection is en abled, a ...

  • RAD Data comm ASMi-52 - page 151

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Advanced Setup B-15 B.9 Advanced Setup The Advanced Setup menu is used to se lect the desired group of IR-IP configuration parameters. The parameters accessed through Advanced Setup menu supplement the parameters available on the Quick Setup sc reen, by providing c ...

  • RAD Data comm ASMi-52 - page 152

    Appendix B IR-IP Interface Module Installation and Operation Manual B-16 Advanced Setup ASMi-52 Ver. 2.5 IR_IP <IR-IP> S/W Ver. 1.21 (date) Quick Setup Management Access Advanced Setup ................................................................. Device identification Interface Parameters ================================================== ...

  • RAD Data comm ASMi-52 - page 153

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Advanced Setup B-17 Defining the WAN Protocol Parameters Frame Relay Protocol The Frame Relay Protocol Parameters menu is use d to configure the parameters Frame Relay WAN for protocol (the WAN protocol is selected by means of t he Quick Setup ) in Figure B-5 .  ...

  • RAD Data comm ASMi-52 - page 154

    Appendix B IR-IP Interface Module Installation and Operation Manual B-18 Advanced Setup ASMi-52 Ver. 2.5 PPP Protocol Menu The PPP Protocol Parameters menu is us ed to configure the parameters PPP WAN for protocol (the WAN protocol is selected by means of the (the WAN protocol is selected by means of the Quick Setup ) in Figure B-5 .  To define ...

  • RAD Data comm ASMi-52 - page 155

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Advanced Setup B-19 Defining the Multicast Parameters The Multicast IP menu is used to spec ify the IP multicast frame forwarding parameters, and to access the static multicast grou ps’ table.  To define the Multicast Parameters: 1. From the Advanced Setup men ...

  • RAD Data comm ASMi-52 - page 156

    Appendix B IR-IP Interface Module Installation and Operation Manual B-20 Using the Device Control Menu ASMi-52 Ver. 2.5  To access the Static Gro ups menu: 1. From t he Multicast IP menu, type 2 . The following screen appears: IR_IP <IR-IP> S/W Ver. 1.21 (date) Static Multicast Groups Table ----------------------------- Group IP Address 1. ...

  • RAD Data comm ASMi-52 - page 157

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Using the Device Control Menu B-21 Downloading New Software IR-IP operates as a TFTP client, an d therefore it is po ssible to update its software by downloading new software from anothe r computer that operates as a TFTP server. The New Software Download menu is u ...

  • RAD Data comm ASMi-52 - page 158

    Appendix B IR-IP Interface Module Installation and Operation Manual B-22 Using the Device Control Menu ASMi-52 Ver. 2.5 Erasing Configuration Selecting Erase Configuration allows you to reset all the configuration parameters to their default values. • Do this o nly if you need to reconfigur e the module a new (all the parameters). • After erase ...

  • RAD Data comm ASMi-52 - page 159

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Viewing IR -IP configuration Data B-23 This operation restarts the IR-IP LAN controller. To continue your Telnet session, press any key within 15 seconds followin g the confirmation of the reset operation. Reset WAN  To reset the WAN interface: • From the Rese ...

  • RAD Data comm ASMi-52 - page 160

    Appendix B IR-IP Interface Module Installation and Operation Manual B-24 Viewing IR-IP configurat ion Data ASMi-52 Ver. 2.5 IR_IP <IR-IP> S/W Ver. 1.21 (date) VIEW CONFIGURATION ------------------ BOOT Version: 1.06 18.03.1999 Device Name: IP router card System Location: The location of this device Contact Person: Name of contact Person MAC A ...

  • RAD Data comm ASMi-52 - page 161

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Viewing IR -IP configuration Data B-25 IR_IP <IR-IP> S/W Ver. 1.21 (date) Multicast Groups Table ---------------------- Group IP Address Status Group IP Address Status Press any key for exit Figure B-21. Multicast Groups Table Screen Viewing the Statistics Sc ...

  • RAD Data comm ASMi-52 - page 162

    Appendix B IR-IP Interface Module Installation and Operation Manual B-26 Using Diagnostic Tools (Pin g Terminal) ASMi-52 Ver. 2.5 IR_IP <IR-IP> S/W Ver. 1.21 (date) SYSTEM STATISTICS ----------------- Counter Name Val Counter Name Val WAN in Octets 83504 WAN Alignment Errors 0 WAN Out Octets 1950 WAN Aborted Frames 0 WAN Out Frames 1723 WAN S ...

  • RAD Data comm ASMi-52 - page 163

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Using Diagnost ic Tools (Ping Terminal) B-27 Using the Ping Function The Ping option is used to confirm IP connectivity by pinging othe r IP hosts. Connectivity is confirmed by receiving a re ply from the remote (pinged) IP h ost.  To ping a host: 1. From the Di ...

  • RAD Data comm ASMi-52 - page 164

    Appendix B IR-IP Interface Module Installation and Operation Manual B-28 Erasing IR-IP Software ASMi-52 Ver. 2.5 B.13 Erasing User’s Configuration The user-defined configuration parameters are stored in the IP router card flash memory. After the user-defined configuratio n parameters are erased, the IP router card automatically loads the default ...

  • RAD Data comm ASMi-52 - page 165

    Installation and Operation Manual Appendix B IR-IP Interface Module ASMi-52 Ver. 2.5 Erasing IR-IP Software B-29 Erasing Application Software  To erase the application software: 1. Turn ASMi-52 of f. 2. Set all the four sectio ns of IR-IP DIP switch to ON. 3. Turn ASMi-52 on and monitor the ERR and LINK indicators: they must blink alternately. 4 ...

  • RAD Data comm ASMi-52 - page 166

    Appendix B IR-IP Interface Module Installation and Operation Manual B-30 IR-IP Troubleshooting ASMi-52 Ver. 2.5 5. Run a stan dard TFTP client application on the Telnet host, and download the appropriate software file.  If the download is successful, IR-IP starts using the new software.  If the downloading fails, repeat the download process. ...

  • RAD Data comm ASMi-52 - page 167

    ASMi-52 Ver. 2.5 Technical Specifications C-1 Appendix C Easy Config Device This appendix describes the Easy Config hand-held device intended for ASMi-52 configuration via the V.24 (RS-232) control port, eliminating the need for an ASCII terminal. Using the Easy Config, the local user can perform the same configuration, monitoring and diag nostic f ...

  • RAD Data comm ASMi-52 - page 168

    Appendix C Easy Config Device Installation and Operation Manual C-2 Installation ASMi-52 Ver. 2.5 C.3 Installation Package Contents The Easy Config package contains the following items: • Easy Config device • AC/DC power adapter • Interface cable with DB-9 male and female connec tors. Connecting the Interface Cable The control port of the Eas ...

  • RAD Data comm ASMi-52 - page 169

    Installation and Operation Manual Appendix C Easy Config Device ASMi-52 Ver. 2.5 Operation C-3 C.4 Operation Turning the Easy Config On  To turn the Easy Config on: • Set the top panel BAT switch to OFF if the Easy Config receives power from the external AC/DC adapter. or • Set the top panel BAT switch to ON if th e Easy Config receives powe ...

  • RAD Data comm ASMi-52 - page 170

    Appendix C Easy Config Device Installation and Operation Manual C-4 Operation ASMi-52 Ver. 2.5 Scrolling the ASMi-52 Menus The Easy Config enables the user to scro ll through the ASMi-52 menu s. The menu structure is circular – the menu scr eens are displayed on the LCD one after another in cyclic order.  To scroll down the menus: • Press th ...

  • RAD Data comm ASMi-52 - page 171

    Installation and Operation Manual Appendix C Easy Config Device ASMi-52 Ver. 2.5 Operation C-5 5. Repeat steps 3– 4 to complete the selection.  Use the s character as a space  Use the ESC button to delete the last entered character. 6. Press the ENTER button t o accept selected values. 7. If an invalid value is entered, Error Reconfigure me ...

  • RAD Data comm ASMi-52 - page 172

    Appendix C Easy Config Device Installation and Operation Manual C-6 Operation ASMi-52 Ver. 2.5 7. Press the x button to sel ect the value. The s character designating space is stored in the bottom row: s 111s 8. Repeat steps 4– 7 to enter the remain ing values. Mind the spaces between the IP address portion s. The resulting display should look as ...

  • RAD Data comm ASMi-52 - page 173

    ASMi-52 Ver. 2.5 I-1 Index —A— AC Power, 2-4 Adapter cable CBL-RJ-45/2BNC/E1, 1-5 Aging timeout, 4-9 Alarm reporting, 1-10 Alarm Relay, 1-14 connecting, 2-4 Alarms clearing, 6-10 displaying, 6-9 index of, 6-11 masking, 6-11 Applications, 1-2, B-2 ASMi-52 Menu map, 3-11 Autoconfiguration TFTP or XMODEM, 4-44 Autonegotiation, 4-12 —B— BERT Pa ...

  • RAD Data comm ASMi-52 - page 174

    Index Installation and Operation Manual I-2 ASMi-52 Ver. 2.5 parameters, B-6 Default settings, 3-4 control port, 3-5 E1/E1+Ethernet/E1+Serial DTE interface, 3-6 LAN configuration, 3-4 resetting, 4-47 Serial DTE interface, 3-6 SHDSL interface, 3-5 system, 3-4 Detecting errors, 6-8 Device information, 4-1 DHCP Relay, B-12 Diagnostics, 1-9, 1-14 Dial- ...

  • RAD Data comm ASMi-52 - page 175

    Installation and Operation Manual Index ASMi-52 Ver. 2.5 I-3 reset to default values, B-22 Reset WAN, B-23 resetting, B-22 static groups, B-19 statistics, B-25 technical specifications, B-2 —L— LAN Aging timeout, 4-9 autonegotiation, 4-12 Configuration, 4-7 fault indication, 4-12 rate, 4-10 LEDs, 1-12 front panel, 3-3, 6-8 IR-IP, B-4 test, 6-24 ...

  • RAD Data comm ASMi-52 - page 176

    Index Installation and Operation Manual I-4 ASMi-52 Ver. 2.5 changing, 4-20 default, 4-40 Performance monitoring, 1-14 Physical description, 1-10 Plastic Enclosure, 1-15 Pinout RJ-45, B-3 Point-to-Point Protocol (PPP), B-1 Port alarms masking, 6-11 Port log file, 6-15 Port status, 6-10 display, 4-39 Power Cables, 2-4 Power Source, 1-15 Power-up sel ...

  • RAD Data comm ASMi-52 - page 177

    Installation and Operation Manual Index ASMi-52 Ver. 2.5 I-5 Timeslots mapping E1, 4-32 Timing, 1-8, 1-14 Troubleshooting, 6-15 TSA, 4-34 Turning off, 3-15 —U— Unit enclosure, 1-2 Unit identical settings, 4-34 User name, 4-40 —V— Versions, 1-1 Virtual connection, 4-39 —X— XMODEM installing new software, 4-44 ...

  • RAD Data comm ASMi-52 - page 178

    Index Installation and Operation Manual I-6 ASMi-52 Ver. 2.5 ...

  • RAD Data comm ASMi-52 - page 179

    Supplement Drilling T emplate for W all Inst allation 377-900-02/06 1 This panel is drawn to scale. T o drill the holes for a wall inst allation, tear this page out of the manual or print it and hold it against the wall. on letter-size paper (8.5"x1 1.0") 1 33 22 LEDs facing up - drill at . 1 LEDs facing down - drill at . LEDs facing left ...

  • RAD Data comm ASMi-52 - page 180

    ...

  • RAD Data comm ASMi-52 - page 181

    24 Raoul W allenberg St., T el Aviv 69719, Israel T el: +972-3-6458181, F ax: +9 72-3-6483331, +972-3-6498250 E-mail: , W eb site: Customer Response Form RAD Data Communications would like your hel p in improving its product documentation. Please complete and return this form by mail or by fax or s end us an e-mail with your comments. Thank you for ...

  • RAD Data comm ASMi-52 - page 182

    ...

  • RAD Data comm ASMi-52 - page 183

    Error Report Type of Error(s) ❒ Incompatibility with product or Problem(s): ❒ Difficulty in understanding text ❒ Regulatory in formation (Safety, Compliance, Warnings, etc.) ❒ Difficulty in finding needed informat ion ❒ Missing information ❒ Illogical flow of information ❒ Style (spelling, grammar, references, etc.) ❒ Appearance ❒ ...

  • RAD Data comm ASMi-52 - page 184

    ...

  • RAD Data comm ASMi-52 - page 185

    ...

  • RAD Data comm ASMi-52 - page 186

    Publication No. 148-20 0-04/06 www.rad.com INTERNATIONAL HEADQUARTER S: 24 Raoul Wallenberg Street, Tel Aviv 69719, Israel, Tel: 972-3-6458181 Fax: 972-3-6498250, 972-3-647 4436, Email: market@rad.com NORTH AMERICA HEADQUARTE RS: 900 Corporate Drive, Mahwah, N.J. 07430, Tel: (2 01) 529-1100 Toll Free: 1-800-444-7234, Fa x: (201) 529-5777, Email: ma ...

Produzent RAD Data comm Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts RAD Data comm ASMi-52 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen RAD Data comm
- Bedienungsanleitungen ASMi-52
- Produktkarten RAD Data comm
- Informationsbroschüren
- oder Energieetiketten RAD Data comm ASMi-52
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung RAD Data comm ASMi-52.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen RAD Data comm ASMi-52, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen RAD Data comm ASMi-52. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts RAD Data comm ASMi-52 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts RAD Data comm ASMi-52, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von RAD Data comm ASMi-52 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von RAD Data comm ASMi-52 verständlich ist.

Eine gänzliche Bedienungsanleitung von RAD Data comm sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von RAD Data comm ASMi-52 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von RAD Data comm ASMi-52 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich RAD Data comm ASMi-52, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts RAD Data comm ASMi-52 - die uns die ersten Schritte während der Nutzung von RAD Data comm ASMi-52 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit RAD Data comm ASMi-52 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von RAD Data comm ASMi-52 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich RAD Data comm ASMi-52?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit RAD Data comm ASMi-52 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit RAD Data comm ASMi-52 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)