Deutsch dropdown-ico

Bedienungsanleitung Apple 13 INCH LATE 2006

357 Seiten 63.43 mb
Download

Zur Seite of 357

Summary
  • Apple 13 INCH LATE 2006 - page 1

     Service Source © 2006, 2007 Apple Inc . All rights re ser ved. MacBook (13-inch) MacBook (1 3-inch) MacBook (1 3-inch Late 2006) MacBook (1 3-inch Mid 2007) Updated 1 June 2007 ...

  • Apple 13 INCH LATE 2006 - page 2

    ii MacBook (13-inch) Contents T ake Apart General Information 7 What’ s New 7 Pr oduc t Congura tions 8 V er tical-Insert Connectors 1 0 T ools 1 0 P ower Adapt er 1 1 T emperatur e Concerns 1 1 Note About Images in This Manual 1 1 Logic Board Springs 1 2 Simplied Flow char t for T ake Apart 1 3 Battery 1 4 RAM Door (L-Bracket) 1 7 Memory ( ...

  • Apple 13 INCH LATE 2006 - page 3

    iii Heatsink 7 4 Checking the Thermal Grease 78 Comparing Heatsinks 84 Bluetooth Holder 85 Optical Drive 8 9 Handling Slot-Load Optical Drive s 99 Removing a Stuck Disc from an Optical Drive 1 03 Optical Drive Cable 105 I/O Frame (with upper EMI shield) 10 9 Logic Board 1 13 DIMM Lever Kit 122 Backup Battery 12 6 Bluetooth Antenna Board and Cable 1 ...

  • Apple 13 INCH LATE 2006 - page 4

    iv Clutch Cover 193 Bezel Scoops, Left and Right 19 9 LCD Panel 203 Antenna Receptors and Cables, T op and Left 20 9 Antenna Receptor and Cable, Right (Late 2006 Model Only) 21 4 LCD Panel Assembly 222 Removal P rocedure 22 4 Reinstallation Pr ocedure 229 Foil at Camera Bracket (Original MacBook Model) 23 7 Spacers at Camera Bracket 240 Camera Asse ...

  • Apple 13 INCH LATE 2006 - page 5

    v P ar t Location 3 04 Pr ocedure 305 T roubleshooting General Information 320 T roubleshooting Steps 321 Symptom Charts 32 4 Block Diagram 33 4 V iews External and Internal V iews 33 7 F ront : Keyboard and IR Windo w 3 3 7 Back: Air V ents and Display Clutch 3 38 Left Side: P or ts 3 3 8 Right Side: Slot Drive 338 Battery Bay : Memor y Card Lev e ...

  • Apple 13 INCH LATE 2006 - page 6

     Service Source © 2006, 2007 Apple Inc . All rights re ser ved. T ake Apart MacBook (13-inch) ...

  • Apple 13 INCH LATE 2006 - page 7

    MacBook (1 3-inch) T ake Apar t — General Information 7 General Information What’ s New The MacBook (1 3-inch) portable computer is the rst computer of its size fea turing the Intel Core Duo processor and built-in iSight video camera. T he main features and service di erences (from similar-sized Apple portable computers) include: Higher r ...

  • Apple 13 INCH LATE 2006 - page 8

    MacBook (1 3-inch) T ake Apar t — General Information 8 Built-in keyboard as par t of top case Operating temperatur e is hotter than previous models (refer to “ T emperature Concerns ” in this chapter) Pr oduct Congurations The following table sho ws the MacBook (1 3-inch) model congurations at introduction: F eature Good Better Best In ...

  • Apple 13 INCH LATE 2006 - page 9

    MacBook (1 3-inch) T ake Apar t — General Information 9 Keyboard integral t o top case: Pr oduc t name on displa y bezel: MagSafe power connector port: Infrared window on fron t of computer: F or additional views of the computer , refer t o the “ Views” chapter at the end of this manual. ...

  • Apple 13 INCH LATE 2006 - page 10

    MacBook (1 3-inch) T ake Apar t — General Information 1 0 V ertical-Insert Connectors Most of the cable connectors on the logic board use a new design that require s special inser tion and extraction. C aution: T o prevent damage to the connectors, install them from the front (away from the cable) when reconnecting vertical-inser t cables to the ...

  • Apple 13 INCH LATE 2006 - page 11

    MacBook (1 3-inch) T ake Apar t — General Information 1 1 Power Adapter W arning: The power adapter f or this computer is unique to this model. It uses an MPM 4-pin adapter plug. Do not use this power adapter with any other portable computer . P ower adapters from earlier iBook or P owerBook computers are not compatible and will not t the MPM ...

  • Apple 13 INCH LATE 2006 - page 12

    MacBook (1 3-inch) T ake Apar t — General Information 1 2 Logic Board Springs Caution: When ser vicing the computer , be especially careful when working near the two springs on the logic board. Although the springs are exible, they can be inadvertently torn, bent, or broken if a cable gets caught on them. A logic board might be considered unus ...

  • Apple 13 INCH LATE 2006 - page 13

    MacBook (1 3-inch) T ake Apar t — General Information 1 3 Simplied Flowchart for T ake Apart Although this owchart does not include every ser viceable par t, you can use it as a reference after becoming familiar with the detailed remov al procedures. Remov e RAM Door (L-Brack et) Remov e T op Case with K eyboard Disconnect LCD P anel Assemb ...

  • Apple 13 INCH LATE 2006 - page 14

    MacBook (1 3-inch) T ake Apar t — Battery 1 4 Battery T ools Clean, soft, lint-free cloth Coin Part Location Pr eliminary Steps W arning: Always shut down the c omputer before opening it to av oid damaging the internal components or causing injury . After you shut down the comput er , the internal components can be very hot. L et the computer coo ...

  • Apple 13 INCH LATE 2006 - page 15

    MacBook (1 3-inch) T ake Apar t — Battery 1 5 W ait 30 minutes to allo w the computer ’ s internal components to cool. Unplug all external cables from the computer ex cept the power cord . Unplug the power cor d. Put on an ESD wrist strap . T urn over the computer and plac e it on a sof t cloth. Use a coin to release the ba tter y latch. T urn ...

  • Apple 13 INCH LATE 2006 - page 16

    MacBook (1 3-inch) T ake Apar t — Battery 1 6 Reassemble and test the computer . 10. ...

  • Apple 13 INCH LATE 2006 - page 17

    MacBook (1 3-inch) T ake Apar t — RAM Door 1 7 RAM Door (L-Bracket) T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove the battery . Part Location • • • • ...

  • Apple 13 INCH LATE 2006 - page 18

    MacBook (1 3-inch) T ake Apar t — RAM Door 1 8 Pr ocedure With the computer closed and upside down on a soft cloth, touch a metal sur face inside the battery bay to discharge any sta tic elec tricity . Loosen—but do not try to remove—the three captiv e screws along the RAM door . 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 19

    MacBook (1 3-inch) T ake Apar t — RAM Door 1 9 Holding the long end of the L-shaped RAM door , pivot it out from the batt er y bay . (If necessary , use a black stick to tilt it up and out of the battery bay .) Be careful not to bend it. Replacement Note: Bef ore replacing the RAM door , make sure that • Hard drive pull tab is not exposed • C ...

  • Apple 13 INCH LATE 2006 - page 20

    MacBook (1 3-inch) T ake Apar t — RAM Door 20 Replacement Note: Install the replacement RAM door by rst aligning the short end at the notch near the hard drive opening . Replacement Note: U se a black stick, if nec essar y , to tuck in the EMI gaskets so they do not protrude from the edge of the battery bay . Make sure the three screws align w ...

  • Apple 13 INCH LATE 2006 - page 21

    MacBook (1 3-inch) T ake Apar t — Memory 2 1 Memory (DIMMs) This computer come s with a minimum of 5 1 2 MB of 667 GHz Double Data Rate 2 (DDR2) Synchronous Dynamic R andom-A ccess Memor y (SDRAM) installed. It has two slots that can accept SDRAM Small Outline Dual Inline Memor y Modules (SO-DIMMs). The slots are side-by-side on the logic board b ...

  • Apple 13 INCH LATE 2006 - page 22

    MacBook (1 3-inch) T ake Apar t — Memory 22 Removal Pr ocedure T ouch a metal sur face inside the battery bay to discharge any static electricity . Put on an ESD wrist strap . In one swift motion, use one nger to move the lever to the left and release it. This swift motion ejects the memor y card . Caution: The memor y card eject levers are on ...

  • Apple 13 INCH LATE 2006 - page 23

    MacBook (1 3-inch) T ake Apar t — Memory 23 Holding the memor y cards b y the corners, slide them out from the battery bay . Important: Do not touch the gold connectors. Handle the card only by its edges. Note: A memory card might show a white residue when you r emove it. This harmless substance acts as a lubricant when installing the memor y car ...

  • Apple 13 INCH LATE 2006 - page 24

    MacBook (1 3-inch) T ake Apar t — Memory 24 Use two ngers to push rmly on the edge of the memory cards. If there is a tight t, installing the cards may take some for ce to ensure that they are fully inserted. Important: W hen the cards are fully inser ted , the edges of the cards are nearly hidden, as shown by the rece ssed card on the r ...

  • Apple 13 INCH LATE 2006 - page 25

    MacBook (1 3-inch) T ake Apar t — Memory 25 Removing a Stuck Memory Card If a lever becomes inoperable and does not eject a memory card, you must remo ve the top case to access the stuck memory card. F ollow this procedure only if the memory card is stuck and cannot be ejected by using the lever . F ollow the “ T op Case” procedure in this ch ...

  • Apple 13 INCH LATE 2006 - page 26

    MacBook (1 3-inch) T ake Apar t — Hard Drive 26 Hard Drive T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Part Location • • • • ...

  • Apple 13 INCH LATE 2006 - page 27

    MacBook (1 3-inch) T ake Apar t — Hard Drive 27 Pr ocedure If the hard drive pull-tab is tucked in, use a black stick to unroll it. Pull the tab straight out t o slide the drive out from the rubber rails in the battery bay . 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 28

    MacBook (1 3-inch) T ake Apar t — Hard Drive 28 Hold the drive only by the sides when remo ving and replacing it. Install the replacement har d drive, and reassemble and test the comput er . Important: After a new hard drive replacement, you must update the operating system to Mac OS X version 1 0.4.6 or later . Replacement Note: If you are insta ...

  • Apple 13 INCH LATE 2006 - page 29

    MacBook (1 3-inch) T ake Apar t — T op Case 29 T op Case (with Keyboard) T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Magnetic Phillips #00 screwdriver (pref erably with a long handle) Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Access car d (Apple par t number 9 22-7 1 72 ...

  • Apple 13 INCH LATE 2006 - page 30

    MacBook (1 3-inch) T ake Apar t — T op Case 30 Pr ocedure Caution: T o prevent scra tches or other cosmetic damage to the computer housing , use a soft cloth as a protective lay er when removing and installing the external screws. With the computer upright, remov e the two identical 5 .5-mm long shoulder screws from the right side of the computer ...

  • Apple 13 INCH LATE 2006 - page 31

    MacBook (1 3-inch) T ake Apar t — T op Case 3 1 T urn over the computer , and on the outside of the bottom case, remov e the three #0 Phillips screws: • T wo 1 4-mm long screws near display hinge • One 1 1-mm long at cent er of bottom case Replacement C aution: Do not put one of the longer screws in the center screw hole or it will damage the ...

  • Apple 13 INCH LATE 2006 - page 32

    MacBook (1 3-inch) T ake Apar t — T op Case 3 2 Notice the long row of #0 Phillips scr ews at the front edge of the battery bay . Important: Remove only the four screws shown. Remove the 3-mm long identical screws as follows: Starting at the corner closest to the battery connec tor , sk ip the rst screw , then remov e the second , f our th, se ...

  • Apple 13 INCH LATE 2006 - page 33

    MacBook (1 3-inch) T ake Apar t — T op Case 3 3 In the battery bay , use a long-handled screwdriver to r emove the three #00 Phillips screws at the inner edge of the battery bay near where the RAM slots are located: • T wo identical 3-mm long screws • One longer 4.5-mm long screw at the corner of the battery bay nearest the batt er y connecto ...

  • Apple 13 INCH LATE 2006 - page 34

    MacBook (1 3-inch) T ake Apar t — T op Case 34 With the top and right side gap opened , tilt up—but do not r emove—the right edge of the top case. This motion r eleases the remaining snaps between the top case and bottom case , and the slot-load bezel clips become loose as the top case is tilted up . 11. ...

  • Apple 13 INCH LATE 2006 - page 35

    MacBook (1 3-inch) T ake Apar t — T op Case 3 5 Raise up the top case so you can see where the folded tr ack pad ex cable attaches to the logic board. Late 2006 Model: 12. ...

  • Apple 13 INCH LATE 2006 - page 36

    MacBook (1 3-inch) T ake Apar t — T op Case 36 Use the at end of a black stick to reach in and disc onnec t the trackpad cable. F or the Late 2006 model, use the pull-tab to disconnect the trackpad cable. 13. ...

  • Apple 13 INCH LATE 2006 - page 37

    MacBook (1 3-inch) T ake Apar t — T op Case 3 7 Lift the top case up and away from the c omputer assembly . Late 2006 Model: 14. ...

  • Apple 13 INCH LATE 2006 - page 38

    MacBook (1 3-inch) T ake Apar t — T op Case 38 Refer to the f ollowing notes to install the replacement t op case, and reassemble and test the computer . Replacement Note: The top case includes heatstaked keyboard, webbing , EMI shield, a small rectangular foam pad , and a ttached track pad cable. Replacement Note: Bef ore replacing the top case, ...

  • Apple 13 INCH LATE 2006 - page 39

    MacBook (1 3-inch) T ake Apar t — T op Case 39 Replacement C aution: If any of the four bezel clips at the slot-load bez el come loose, simply insert them back in the slots. M ake sure they are in place while r eassembling the computer and before installing the top case . Install the right side of the top case rst (near the disc bezel) to lock ...

  • Apple 13 INCH LATE 2006 - page 40

    MacBook (1 3-inch) T ake Apar t — T op Case 40 Replacement Note: When installing the screws at the rear corners of the bottom case, insert an access card tool betw een the top case and the display to maintain light pr essure as the screws are tightened . ...

  • Apple 13 INCH LATE 2006 - page 41

    MacBook (1 3-inch) T ake Apar t — T rackpad Cable (Late 2006 Model Only) 4 1 T rackpad Cable (Late 2006 Model Only) T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location ? ...

  • Apple 13 INCH LATE 2006 - page 42

    MacBook (1 3-inch) T ake Apar t — T rackpad Cable (Late 2006 Model Only) 42 Pr ocedure Place the top case (keyboard side down) on a clean surface. Replacement Note : Refer to the following image when attaching a r eplacement trackpad cable. The folds in the cable and the ar eas that adhere to the top case should appear as shown. Use a black stick ...

  • Apple 13 INCH LATE 2006 - page 43

    MacBook (1 3-inch) T ake Apar t — T rackpad Cable (Late 2006 Model Only) 43 Hold the trackpad cable in place as you peel up—but do not remove—the tape . P eel up the mylar shield that protects the trackpad circuitry. 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 44

    MacBook (1 3-inch) T ake Apar t — T rackpad Cable (Late 2006 Model Only) 44 Note: The shape of the m ylar shield may di er slightly . This one includes a squared-o tab: Caution: The trackpad cable lock ing lever at the top of the c onnec tor is fragile . Use a black stick to carefully tilt up the lever un til it is ver tical (as shown by th ...

  • Apple 13 INCH LATE 2006 - page 45

    MacBook (1 3-inch) T ake Apar t — T rackpad Cable (Late 2006 Model Only) 45 With the cable locking lever open, pull the cable down to remove it from the c onnec tor . Carefully peel up the trackpad cable from where it adheres t o the underside of the top case. Install the replacement trackpad cable , and reassemble and t est the computer . 6. 7. ...

  • Apple 13 INCH LATE 2006 - page 46

    MacBook (1 3-inch) T ake Apar t — AirP ort Ex treme Card 46 AirPort Extreme Card T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Magnetic Phillips #0 screwdriver Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • ...

  • Apple 13 INCH LATE 2006 - page 47

    MacBook (1 3-inch) T ake Apar t — AirP ort Ex treme Card 47 Pr ocedure Caution: When ser vicing the computer , be especially careful when working near the two springs on the logic board. Although the springs are exible, they can be inadvertently torn, bent, or broken if a cable gets caught on them. A logic board might be considered unusable wi ...

  • Apple 13 INCH LATE 2006 - page 48

    MacBook (1 3-inch) T ake Apar t — AirP ort Ex treme Card 48 Pull the card up slightly and out of the car d socket on the lo gic board . Use a black stick to mov e aside the speaker cable. Disconnect the two cables from the AirP ort Card. Note that the black cable is on the left and the gray cable is on the right. Tip: T o remember the cable locat ...

  • Apple 13 INCH LATE 2006 - page 49

    MacBook (1 3-inch) T ake Apar t — AirP ort Ex treme Card 49 Late 2006 Model: This model has three ant enna cables. Disconnect the black, blue , and gray cables. Install the replacement AirP or t Card , and r eassemble and test the computer . Replacement Note: If the comput er model that you are servicing includes tape over the antenna cables , re ...

  • Apple 13 INCH LATE 2006 - page 50

    MacBook (1 3-inch) T ake Apar t — AirP ort Ex treme Card 50 Late 2006 Model Replacement Not e: Notice that the AirP or t Card has numbers 2, 1, and 0 printed on the card . The numbers correspond to the ant enna cable colors where 2 = black, 1 = blue, and 0 = gra y . Replacement C aution: When connecting the AirPort antenna cables , make sure the ...

  • Apple 13 INCH LATE 2006 - page 51

    MacBook (1 3-inch) T ake Apar t — MagSafe DC-In Board 5 1 MagSafe DC-In Board T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • • ...

  • Apple 13 INCH LATE 2006 - page 52

    MacBook (1 3-inch) T ake Apar t — MagSafe DC-In Board 52 Pr ocedure Place a black stick under the DC-in connector cables to help disc onnec t the connector , then pull the connector away fr om its connec tion on the logic board . (Note: Although the cables are solid black on the Late 2 006 model, the st eps are the same.) Remove the 3-mm long scr ...

  • Apple 13 INCH LATE 2006 - page 53

    MacBook (1 3-inch) T ake Apar t — MagSafe DC-In Board 53 F rom the por t side, use a black stick to help tilt up the MagSafe DC-in board and r emove it from the logic board . Replacement Note: Make sure the f olded side of the EMI shield ts over the I/O frame rib so that the rib is sandwiched between the anges of the EMI shield . Replacemen ...

  • Apple 13 INCH LATE 2006 - page 54

    MacBook (1 3-inch) T ake Apar t — MagSafe DC-In Board 54 Install the replacement MagSafe DC-in boar d, and reassemble and test the comput er . Replacement Note: C heck that there are no bent EMI ngers on the shield cov ering the p ort area. Replacement Note: C heck the por t side of the bottom case to make sure the MagSafe DC-in por t is level ...

  • Apple 13 INCH LATE 2006 - page 55

    MacBook (1 3-inch) T ake Apar t — Left Speaker 55 Left Speaker T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • • • • • ? ...

  • Apple 13 INCH LATE 2006 - page 56

    MacBook (1 3-inch) T ake Apar t — Left Speaker 56 Pr ocedure Disconnect the speaker cable from the logic board. Remove the 8.5-mm long ground scr ew at the upper right corner of the AirPort Extreme Card . Route the cable underneath the AirP or t cables . 1. 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 57

    MacBook (1 3-inch) T ake Apar t — Left Speaker 57 Remove the 6-mm long speaker screw . Pull up on the s peak er cable to remo ve it from the frame. Pivot up the speaker from the left corner . 4. 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 58

    MacBook (1 3-inch) T ake Apar t — Left Speaker 58 Route the speaker cable underneath the DC-in cable. Install the replacement s peak er cable , and reassemble and test the computer . Replacement Note: T o prevent a pinched cable , make sure the cable is routed as shown. 7. 8. ...

  • Apple 13 INCH LATE 2006 - page 59

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 59 Battery Connector with Sleep Switch T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with ...

  • Apple 13 INCH LATE 2006 - page 60

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 60 Pr ocedure Caution: Do not touch the raised section of the sleep switch connector . I t is fragile and could break. Remove the two 4.5-mm long shoulder scr ews from the frame at the battery connec tor . Replacement C aution: Make sure the screws are the proper length. A long ...

  • Apple 13 INCH LATE 2006 - page 61

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 6 1 Tilt up the battery connec tor end of the board . If provided , remove the single screw that secures the ba tter y cable clip to the I/O frame. 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 62

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 62 Tilt up the battery cable clip, and remove it fr om the computer assembly . Replacement Note: Be sur e to install the batter y cable clip when reassembling the computer . 4. ...

  • Apple 13 INCH LATE 2006 - page 63

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 63 Caution: Do not touch the raised section of the sleep switch connector . I t is fragile and could break. Using a black stick, insert it under the cables, and lift up the connec tor fr om the logic board. Replacement Note: T o avoid bending the pins on the sleep switch c onne ...

  • Apple 13 INCH LATE 2006 - page 64

    MacBook (1 3-inch) T ake Apar t — Battery Connector with Sleep Switch 64 Install the replacement batt er y connector with sleep switch, and reassemble and test the computer . Caution: T o avoid pinching the cable , the ba tter y connector cable must be properly tucked into the cable channel, as shown by the image on the left, below: Replacement N ...

  • Apple 13 INCH LATE 2006 - page 65

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 65 Hard Drive Connector T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool) Pr eliminary Steps Before you begin, remove Battery RAM door Hard driv e T op case with keyboard Part ...

  • Apple 13 INCH LATE 2006 - page 66

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 66 Pr ocedure Remove the two 6-mm long scr ews from the hard drive connector at the right front side of the computer . Carefully lift up the hard drive connector from the bottom case . This action automatically disconnects the hard drive board from the sleep LED/IR rec eiver ex cable. 1. ...

  • Apple 13 INCH LATE 2006 - page 67

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 67 Replacement C aution: Note the tiny connector at the end of the hard driv e board. It connects to the sleep LED/ IR receiver board a t the front right corner of the computer via a tiny ex cable. T o reinstall the ex cable, rst peel up the end of the snubber to access the length ...

  • Apple 13 INCH LATE 2006 - page 68

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 68 Pull up the hard driv e connec tor cable that runs along the bott om edge of the optical drive. Note the three cable routing guide s when reinstalling the cable. Use the two pull tabs to disconnect the optical drive ex cable and the L VDS cable. 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 69

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 69 Use the pull tab to disconnect the hard drive connector cable. Route the hard drive connector cable under the black cables . 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 70

    MacBook (1 3-inch) T ake Apar t — Hard Drive C onnec tor 70 Install the replacement har d drive connector , and reassemble and test the computer . 7. ...

  • Apple 13 INCH LATE 2006 - page 71

    MacBook (1 3-inch) T ake Apar t — F an 7 1 Fan T ools ESD wrist strap and mat Magnetic Phillips #00 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • • • • • • ...

  • Apple 13 INCH LATE 2006 - page 72

    MacBook (1 3-inch) T ake Apar t — F an 72 Pr ocedure P eel up the strip of tape that overlaps the fan near the optical drive. Remove the screws fr om the fan: • 6-mm long screw from the upper left • 3-mm long screw from the upper right (normally hidden underneath the cable bundles) 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 73

    MacBook (1 3-inch) T ake Apar t — F an 73 Tilt up the fan and disconnect the fan cable from the logic board. Holding the fan tilted up from the bottom case , peel away the adhesive f oam that overlaps the fan and the heatsink. Replacement Note: Because the foam strip tears easily , be sur e to install a new strip of adhesive f oam before reassemb ...

  • Apple 13 INCH LATE 2006 - page 74

    MacBook (1 3-inch) T ake Apar t — Heatsink 7 4 Heatsink T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Alcohol wipes Thermal grease syringe (Apple part number 92 2-7 1 4 4) F elt-tip pen (optional) Pr eliminary Steps Before you beg ...

  • Apple 13 INCH LATE 2006 - page 75

    MacBook (1 3-inch) T ake Apar t — Heatsink 7 5 Pr ocedure Remove the f our identical 8-mm long screws from the heatsink. Note that the screw at the lo wer right corner anchors a exible ground tab for the speaker cable that runs along the top of the RAM card carriers. Make sure the tab is sandwiched between the heatsink and the screw when it is ...

  • Apple 13 INCH LATE 2006 - page 76

    MacBook (1 3-inch) T ake Apar t — Heatsink 76 Starting at the lower bracket of the heatsink, star t to tilt it up to loosen it from the logic board. Holding the heatsink by its edges , tilt it up and disc onnec t the two thermistor connectors from the logic board . 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 77

    MacBook (1 3-inch) T ake Apar t — Heatsink 77 Replacement C aution: When installing the heatsink, make sure its two thermistor cables are routed as shown to pr event cable damage. Replacement Note: Make sure you install the thermal sponge over the two thermistor connectors. Important: Anytime the heatsink is remov ed (even if it is to replace ano ...

  • Apple 13 INCH LATE 2006 - page 78

    MacBook (1 3-inch) T ake Apar t — Heatsink 78 Checking the Thermal Gr ease W arning: Whenever the hea tsink is separated from the logic board (e ven if you ar e installing the same heatsink or board), the thermal grease must be checked and possibly replaced . F ailure to do so can cause the computer to o verheat and be damaged . With the heatsink ...

  • Apple 13 INCH LATE 2006 - page 79

    MacBook (1 3-inch) T ake Apar t — Heatsink 79 • If the thermal grease is directly on the heatsink pads (as shown in step 2), continue with the remaining steps in this procedur e. Caution: T his step is required only when the heatsink and logic board a re removed t o replace a lat er par t (such as the bottom case) and the same heatsink and logi ...

  • Apple 13 INCH LATE 2006 - page 80

    MacBook (1 3-inch) T ake Apar t — Heatsink 80 Use an alcohol wipe to complet ely clean the two pads on the heatsink. Caution: T he syringe steps for this procedure a re required only when the heatsink and logic board are r emoved to replac e a later part (such as the b ottom case) and when no new heatsink with pre-applied thermal grease will be i ...

  • Apple 13 INCH LATE 2006 - page 81

    MacBook (1 3-inch) T ake Apar t — Heatsink 8 1 Using the syringe, put a 0. 1 to 0. 1 2 cc dab of thermal grease, in the center , on the mating sur faces of both chips , as shown below . Apply the grease only up to the line that you marked on the syringe. Important: Use one-third of the syringe contents per chip , so in this case, 1/3 of the therm ...

  • Apple 13 INCH LATE 2006 - page 82

    MacBook (1 3-inch) T ake Apar t — Heatsink 82 While centering the heatsink pads o ver the two chips, lower the hea tsink onto the logic board and press on the areas wher e the screw brackets on the heatsink meet the standos on the board. Mak e sure the heatsink is lev el on the board before installing the screws. Install the heatsink (using th ...

  • Apple 13 INCH LATE 2006 - page 83

    MacBook (1 3-inch) T ake Apar t — Heatsink 83 Replacement Note: If you replaced the heatsink from a kit that includes the thermal sponge , install the thermal sponge over the tw o thermistor connec tors . Make sure the connectors are fully seated . Remove the adhesiv e back ing from the sponge , and place the sponge adhesiv e side down ov er the ...

  • Apple 13 INCH LATE 2006 - page 84

    MacBook (1 3-inch) T ake Apar t — Heatsink 84 Comparing Heatsinks The heatsink ref erred to as a 1 .2 mm heatsink can be identied by the number 607-0 1 42 on its label and its thin rectangular thermistor connectors. Order Apple part number 076-1 242 (which includes the heatsink, thermal tape, and sponge) t o replace a 1 .2 mm heatsink. The hea ...

  • Apple 13 INCH LATE 2006 - page 85

    MacBook (1 3-inch) T ake Apar t — Bluetooth Holder 85 Bluetooth Holder Important: The Bluetooth holder is included with a replacement optical drive and should not be removed unle ss it is damaged or no longer sticks to the optical drive housing. T ools ESD wrist strap and mat Any standard siz e CD or DVD disc Black stick (Apple part number 922-50 ...

  • Apple 13 INCH LATE 2006 - page 86

    MacBook (1 3-inch) T ake Apar t — Bluetooth Holder 86 Pr ocedure Insert a CD or D VD disc half way in to the slot drive to help support the dr ive and pr event damage. Use a black stick to slide out the Bluetooth board fr om its holder . 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 87

    MacBook (1 3-inch) T ake Apar t — Bluetooth Holder 87 W arning: T o prevent damage t o the optical drive, do not touch or press an ywhere else on the drive . Use a black stick to carefully pry up the Bluetooth holder from the top of the optical drive. Make sure you use as little pressure as possible to pr event damage to the drive. Replacement No ...

  • Apple 13 INCH LATE 2006 - page 88

    MacBook (1 3-inch) T ake Apar t — Bluetooth Holder 88 Install the replacement Bluetooth holder , remove the optical drive disc , and reassemble and test the computer . 5. ...

  • Apple 13 INCH LATE 2006 - page 89

    MacBook (1 3-inch) T ake Apar t — Optical Drive 89 Optical Drive T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • • • • • ...

  • Apple 13 INCH LATE 2006 - page 90

    MacBook (1 3-inch) T ake Apar t — Optical Drive 90 Pr ocedure With the computer assembly on a clean, scratch-proof surface, locate the Bluetooth boar d and holder . Note that the Bluetooth holder sta ys with the drive and is included with a replacement optical drive . Late 2006 Model: 1. ...

  • Apple 13 INCH LATE 2006 - page 91

    MacBook (1 3-inch) T ake Apar t — Optical Drive 9 1 Tilt up the Bluetooth board from the upper right corner of the optical drive. Disconnect the optical drive ex cable from the logic board . 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 92

    MacBook (1 3-inch) T ake Apar t — Optical Drive 92 P eel up the tape from the optical drive. Carefully lift up or move aside the cable s to remove the single 5 .5-mm long screw at the mounting bracket. Y ou might rst need to disconnect the ground screw by the speaker to loosen the cables and access the mounting br ack et screw . 4. 5. ...

  • Apple 13 INCH LATE 2006 - page 93

    MacBook (1 3-inch) T ake Apar t — Optical Drive 93 Use a black stick to slide the mounting br ack et forward (awa y from the body of the drive and toward the fan) t o disengage it. Slide out the hard drive , and set it aside . 6. 7. ...

  • Apple 13 INCH LATE 2006 - page 94

    MacBook (1 3-inch) T ake Apar t — Optical Drive 94 Access the tw o identical 3-mm long screws along the bottom edge of the drive at the hard drive snubber . (If the snubber is blocking one of the screws, carefully peel up the snubber .) Lift up the cable that runs between the drive and the snubber at the lower edge of the optical drive. 8. 9. ...

  • Apple 13 INCH LATE 2006 - page 95

    MacBook (1 3-inch) T ake Apar t — Optical Drive 95 W arning: Handle the optical drive at the side edge s only . Do not touch or pr ess anywhere else on the drive . Refer to the next section, “Handling Slot-Load Optical Drives .” Grasp the optical drive ex cable and use it as a pull tab as y ou tilt up the optical drive. Be careful where it ...

  • Apple 13 INCH LATE 2006 - page 96

    MacBook (1 3-inch) T ake Apar t — Optical Drive 96 Replacement Note: If y ou are installing a replacement drive , check tha t the sliding bracket that is secured with two screws slide s easily and is not too tight. If it is too tight, loosen the screws just enough so the bracket slides with ease. Note: F or correct cable routing, ref er to the im ...

  • Apple 13 INCH LATE 2006 - page 97

    MacBook (1 3-inch) T ake Apar t — Optical Drive 97 Before installing the optical drive , make sure the cables on the bottom case are routed as shown. 12. ...

  • Apple 13 INCH LATE 2006 - page 98

    MacBook (1 3-inch) T ake Apar t — Optical Drive 98 Install the replacement optical drive and r eassemble and test the computer . Late 2006 Model: ( The blue tape is for controlling vibration; do not remove the tape) Important: For best performance after a new optical drive replacement , be sur e to update the operating system to the la test Mac O ...

  • Apple 13 INCH LATE 2006 - page 99

    MacBook (1 3-inch) T ake Apar t — Optical Drive 99 Handling Slot-Load Optical Drives F ollow the instructions in this sec tion carefully . This procedure shows how to handle slot-load optical drives when they are outside the comput er . Obser ve ESD (electrostatic dischar ge) guidelines when handling optical drives. • ...

  • Apple 13 INCH LATE 2006 - page 100

    MacBook (1 3-inch) T ake Apar t — Optical Drive 1 00 Handle the drive only by the sides and back edge . Do not touch the front of the drive . • • ...

  • Apple 13 INCH LATE 2006 - page 101

    MacBook (1 3-inch) T ake Apar t — Optical Drive 1 0 1 Do not press on the drive or lift it by the top and bottom co ver . Do not handle the drive by the gull wing edge only . • • ...

  • Apple 13 INCH LATE 2006 - page 102

    MacBook (1 3-inch) T ake Apar t — Optical Drive 1 02 When storing optical drives , use approved packaging boxes . Nev er stack loose drives. When returning a defective optical drive , use the original pack aging and an antistatic bag . P ack only one drive per box. • • ...

  • Apple 13 INCH LATE 2006 - page 103

    MacBook (1 3-inch) T ake Apar t — Optical Drive 1 03 Removing a Stuck Disc from an Optical Drive Important: This procedure applies only to 9 .5-mm and 1 2.7-mm slot-load optical drives. Remove the f our identical screws that hold the top cov er to the drive. Slide the top cov er approximately 2 mm tow ard the back of the drive. Lift up the top co ...

  • Apple 13 INCH LATE 2006 - page 104

    MacBook (1 3-inch) T ake Apar t — Optical Drive 1 04 Check the placement of the disc. I t is either clamped to the turntable at the cen ter of the disc, or it is wedged under one or more posts a t the outer edge of the disc. Holding the edge of the disc, press on the cen ter clamp or hold the posts steady as you remove the disc fr om the drive. I ...

  • Apple 13 INCH LATE 2006 - page 105

    MacBook (1 3-inch) T ake Apar t — Optical Drive Cable 1 05 Optical Drive Cable T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Part Location • • • • • • ...

  • Apple 13 INCH LATE 2006 - page 106

    MacBook (1 3-inch) T ake Apar t — Optical Drive Cable 1 06 Pr ocedure W arning: Handle the optical drive at the side edge s only . Do not touch or pr ess anywhere else on the drive . With the optical drive on a clean, scratch-proof surface, use a black stick to evenly pry up the cable connector from the drive. Late 2006 Model: Carefully pry up th ...

  • Apple 13 INCH LATE 2006 - page 107

    MacBook (1 3-inch) T ake Apar t — Optical Drive Cable 1 07 Remove the optical drive cable . Install the replacement optical drive cable , and reassemble and test the computer . 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 108

    MacBook (1 3-inch) T ake Apar t — Optical Drive Cable 1 08 Note that both sides of the cable ha ve an adhesive mesh strip . Note that the cable might also include a m ylar strip. If attached, do not remo ve it. ...

  • Apple 13 INCH LATE 2006 - page 109

    MacBook (1 3-inch) T ake Apar t — I/O F rame 1 09 I/O Frame (with upper EMI shield) T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s T op case with keyboard ...

  • Apple 13 INCH LATE 2006 - page 110

    MacBook (1 3-inch) T ake Apar t — I/O F rame 1 1 0 Pr ocedure At the left side of the computer assembly , r emove the screws from the I/O frame: • T wo identical 7 .5-mm long screws (one at each end) • One 9 .5-mm long screw in the middle Replacement Note: If the I/O frame screw that is closest to the battery connector secures a battery cable ...

  • Apple 13 INCH LATE 2006 - page 111

    MacBook (1 3-inch) T ake Apar t — I/O F rame 1 1 1 Note how the EMI shield on the I/O frame in terlocks with the shield over the por ts. Tilt up the I/O frame to remov e it from the computer assembly . Note that the I/O frame includes the EMI shield . Be careful not to bend the shield as you remove or install it. Install the replacement I/O frame ...

  • Apple 13 INCH LATE 2006 - page 112

    MacBook (1 3-inch) T ake Apar t — I/O F rame 1 1 2 Replacement Note: If the I/O frame screw that is closest to the battery connector secures a battery cable clip, be sure to reinstall the cable clip and scr ew. ...

  • Apple 13 INCH LATE 2006 - page 113

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 3 Logic Board T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Stack of books, weight ed boxes , or other means of support for displa y while removing and replacing left clutch block ...

  • Apple 13 INCH LATE 2006 - page 114

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 4 Part Location Pr ocedure Caution: When ser vicing the computer , be especially careful when working near the two springs on the logic board. Although the springs are exible, they can be inadvertently torn, bent, or broken if a cable gets caught on them. A logic board might be considered unusa ...

  • Apple 13 INCH LATE 2006 - page 115

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 5 Disconnect the optical drive ex cable from the logic board . Without straining the optical drive ex cable , not e the position of the L VDS cable beneath it. Pull the pull-tab to disc onnec t the L VDS cable from the logic board. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 116

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 6 Locate the Bluet ooth antenna cable at the edge of the logic board , and disc onnec t the Bluetooth antenna cable . Pull the pull-tab to disconnect the hard drive cable connector . Remove the 3-mm long screw next to the low er end of the midframe. 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 117

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 7 Remove the 3-mm long screw locat ed between the memor y card carriers, and disconnect the following cables: • sleep switch connector (use a black stick to raise up and disconnect it) • microphone cable • left speaker cable • subwoofer/right s peaker cable Place a heavy box behind the dis ...

  • Apple 13 INCH LATE 2006 - page 118

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 8 Remove the left clutch block and clutch cap , and move aside any cable s that overlap the logic board. Note: Disregard the cable assembly stat e shown in the image below . Replacement Note: When reinstalling the clutch block, refer to “Clutch Block, Left ” in this chapter . Holding the logic ...

  • Apple 13 INCH LATE 2006 - page 119

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 1 9 Replacement Note: When replacing the logic board, make sure all cables are kept clear of the board , and the I/O shield is secur ely positioned along the por ts. Use a black stick, if necessary , to slightly ex the port side of the b ottom case t o install the logic board. If you are installi ...

  • Apple 13 INCH LATE 2006 - page 120

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 20 • Memor y cards • I/O shield Before installing the logic board , make sure the two springs are intact (not bent or broken). 10. ...

  • Apple 13 INCH LATE 2006 - page 121

    MacBook (1 3-inch) T ake Apar t — Logic Board 1 2 1 Before installing the logic board , check the locator pins on the bottom case. Make sure the two openings in the logic board t over the “+-shaped ” locator pins. W arning: Whenever the hea tsink is separated from the logic board (e ven if you ar e installing the same logic board or heatsi ...

  • Apple 13 INCH LATE 2006 - page 122

    MacBook (1 3-inch) T ake Apar t — DIMM Lev er Kit 1 22 DIMM Lever Kit T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s T op case with keyboard AirP or t Ca r ...

  • Apple 13 INCH LATE 2006 - page 123

    MacBook (1 3-inch) T ake Apar t — DIMM Lev er Kit 1 23 Pr ocedure Important: The following image shows the memory cards and hard drive installed in the battery bay . Note the c orrec t position of the memory card levers. Caution: The remaining images pictured in this procedure used a pre-pr oduc tion model, so the direction and appearance of the ...

  • Apple 13 INCH LATE 2006 - page 124

    MacBook (1 3-inch) T ake Apar t — DIMM Lev er Kit 1 24 Lift o the lever , and remove the spring . Note that the spring has a “hook” end and a “st em” end . When replacing the spring, make sure the hook end wraps around the pin on the memory card carrier .. 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 125

    MacBook (1 3-inch) T ake Apar t — DIMM Lev er Kit 1 25 Before installing the replac ement lever and spring , not e that the underside of the lever has an indentation that mat es with the spring stem. Install the replacement lev er , spring, and screw , and check that the lev er moves correctly . Reassemble and test the computer . Replacement Note ...

  • Apple 13 INCH LATE 2006 - page 126

    MacBook (1 3-inch) T ake Apar t — Backup Battery 1 26 Backup Battery T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Before you begin, remove Battery RAM door Memory c ard s T op case with keyboard AirP or t Ca rd MagSafe DC-in board I/O frame F an Heatsink Logic b ...

  • Apple 13 INCH LATE 2006 - page 127

    MacBook (1 3-inch) T ake Apar t — Backup Battery 1 27 Pr ocedure On the underside of the logic board , not e the position of the backup batter y , attached cable , and tape. Using your ngers or a black stick, carefully peel up the backup battery from the adhesive on the logic board. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 128

    MacBook (1 3-inch) T ake Apar t — Backup Battery 1 28 P eel up the tape that holds the backup battery cable in place. Disconnect the cable by pulling the cable straight out from the connector . Replacement Note: If y ou are replacing the backup batter y with a new one , peel the adhesive backing o of the replacemen t batter y , and use a black ...

  • Apple 13 INCH LATE 2006 - page 129

    MacBook (1 3-inch) T ake Apar t — Bluetooth Ant enna Board and Cable 1 29 Bluetooth Antenna Board and Cable T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with ...

  • Apple 13 INCH LATE 2006 - page 130

    MacBook (1 3-inch) T ake Apar t — Bluetooth Ant enna Board and Cable 1 30 Pr ocedure Remove the 3-mm screw fr om the right speaker . Without straining the speaker cable, tilt up the speaker and unroute it from the right corner of the frame. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 131

    MacBook (1 3-inch) T ake Apar t — Bluetooth Ant enna Board and Cable 1 3 1 Use a black stick to unroute the Bluet ooth and speaker cable. Using a black stick, disconnect the Bluetooth antenna cable from the low er right corner of the Bluetooth board . P r y the connector straight up . 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 132

    MacBook (1 3-inch) T ake Apar t — Bluetooth Ant enna Board and Cable 1 32 Install the replacement Bluetooth an tenna board and cable. Replacement C aution: T o prevent a pinched or damaged cable, the cable might be wrapped with tape, as shown. Do not remo ve any tape that is wrapped around the cable . 5. ...

  • Apple 13 INCH LATE 2006 - page 133

    MacBook (1 3-inch) T ake Apar t — Bluetooth Board 1 3 3 Bluetooth Board T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Part Location • • • • • • ...

  • Apple 13 INCH LATE 2006 - page 134

    MacBook (1 3-inch) T ake Apar t — Bluetooth Board 1 34 Pr ocedure Caution: During this procedur e and when applying a replacement Bluetooth board , do not press on the center of the board . The only acceptable area to pre ss on is the right corners of the board near the locator pin and the Bluetooth ant enna cable connec tor . Important: The Blue ...

  • Apple 13 INCH LATE 2006 - page 135

    MacBook (1 3-inch) T ake Apar t — Bluetooth Board 1 3 5 Use a black stick at the lower edge of the boar d to gently loosen the adhesive and lift the board o the bottom case. Tilt up the board and holding the Bluetooth-to-logic board cable close to the connector , pull the cable to disconnect it from the board . 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 136

    MacBook (1 3-inch) T ake Apar t — Bluetooth Board 1 36 Replacement Note: W ithout straining the cable , slide a black stick underneath the board sleeve , and pr ess the connector to secure it to the board . Replacement Note: C onnect the Bluetooth-to-logic board cable rst before adhering the board to the bottom case . Then install the Bluetoot ...

  • Apple 13 INCH LATE 2006 - page 137

    MacBook (1 3-inch) T ake Apar t — Bluetooth-to-L ogic Board Cable 1 3 7 Bluetooth-to-Logic Board Cable T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Bluetooth board ...

  • Apple 13 INCH LATE 2006 - page 138

    MacBook (1 3-inch) T ake Apar t — Bluetooth-to-L ogic Board Cable 1 38 Pr ocedure Important: During this procedure and when applying a replacement Bluetooth-to-logic boar d cable, do not press on the c enter of the Bluetooth board . The only acceptable area to press on is the right corners of the board near the locator pin and the Bluetooth an te ...

  • Apple 13 INCH LATE 2006 - page 139

    MacBook (1 3-inch) T ake Apar t — Bluetooth-to-L ogic Board Cable 1 39 With the Bluetooth cable disconnected from the Bluetooth board , use a black stick to carefully separate the cable fr om the other cables routed along the bottom edge of the subwoofer (micr ophone cable, L VDS cable, speaker/subwoofer cable .) Thread the cable out from under t ...

  • Apple 13 INCH LATE 2006 - page 140

    MacBook (1 3-inch) T ake Apar t — Bluetooth-to-L ogic Board Cable 1 40 Use a black stick close to the Bluetooth cable connector to disconnect it from the corner of the logic board. (Pull the cable straight up .) Replacement Note: C onnect the Bluetooth board cable rst before adhering the Bluetooth board to the bottom case . Make sure the cable ...

  • Apple 13 INCH LATE 2006 - page 141

    MacBook (1 3-inch) T ake Apar t — Bluetooth-to-L ogic Board Cable 1 4 1 Install a replacement Bluetooth-t o-logic board cable, and reassemble and test the comput er . Replacement Note: W ith the cable attached to the Bluet ooth board, install the cable under the subwoofer tabs bef ore routing the cable to the logic board . 6. ...

  • Apple 13 INCH LATE 2006 - page 142

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 42 Subwoofer with Right Speaker Cable T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case wi ...

  • Apple 13 INCH LATE 2006 - page 143

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 43 Pr ocedure W arning: The subwoofer c one is a sensitive device. A void touching the subwoof er cone. Note the cable routing f or the right speaker and the subwoofer . Remove the f ollowing screws: • T wo 3-mm long screws from the opposite corners of the subw oofer body ...

  • Apple 13 INCH LATE 2006 - page 144

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 44 Tilt up the right speaker from the top right corner of the computer assembly , and without straining the speaker cable, unroute it from the cable guides. P eel up the tape. Remove the 7 .5-mm long top ground screw from the midframe. 3. 4. 5. ...

  • Apple 13 INCH LATE 2006 - page 145

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 45 W arning: The subwoofer c one is a sensitive device. A void touching the subwoof er cone. T o prevent e xcessive pre ssure on the subwoofer body , hold it b y the edges as you per form this step . Unroute the speaker cable , and while holding the sides of the subwoofer , ...

  • Apple 13 INCH LATE 2006 - page 146

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 46 Replacement Note: When connec ting the right speaker cable to the logic board , make sure the cable runs securely • over the right memory slot • between the optical drive cable connector and the L VDS cable connector • under the Bluetooth connector • between the f ...

  • Apple 13 INCH LATE 2006 - page 147

    MacBook (1 3-inch) T ake Apar t — Subwoof er with R ight Speaker Cable 1 47 Install the replacement subw oofer with right speaker cable, and reassemble and te st the computer . 9. ...

  • Apple 13 INCH LATE 2006 - page 148

    MacBook (1 3-inch) T ake Apar t — Midframe 1 48 Midframe T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Part Location • • • ? ...

  • Apple 13 INCH LATE 2006 - page 149

    MacBook (1 3-inch) T ake Apar t — Midframe 1 49 Pr ocedure Note the orientation of the cables tha t route over and to the left of the midframe. Remove the two gr ound screws: • 9-mm long screw from the cent er of the midframe • 7 .5-mm long screw near the top of the midframe , next to the subwoofer W arning: The subwoofer c one is a sensitive ...

  • Apple 13 INCH LATE 2006 - page 150

    MacBook (1 3-inch) T ake Apar t — Midframe 1 50 Move aside the L VDS cable and the hard drive connector cable. Remove the two scr ews from the ends of the midframe: • 7 .5-mm long screw at the top • 6-mm long screw at the bottom Without straining the cables between the frame and the midframe , lift them out to reach the 3-mm long fan screw . ...

  • Apple 13 INCH LATE 2006 - page 151

    MacBook (1 3-inch) T ake Apar t — Midframe 1 5 1 Being careful not to strain any nearb y cables or components, tilt out the low er end of the midframe, and remove the midframe from the bottom case . Replacement Note: When tuck ing in the cables into the channel betw een the fan and the midframe, be sure to install them in this order: • Micropho ...

  • Apple 13 INCH LATE 2006 - page 152

    MacBook (1 3-inch) T ake Apar t — Midframe 1 52 Install the replacement midframe , and reassemble and test the computer . 8. ...

  • Apple 13 INCH LATE 2006 - page 153

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 5 3 Display Bezel T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Access car d (Apple par t number 9 22-7 1 72) Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Part Location • ...

  • Apple 13 INCH LATE 2006 - page 154

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 54 Removal Pr ocedure With the display open wider than a 90-degree angle , run an access card along the outer sides and top edge of the bezel wher e it meets the display rear housing . Note: When opening the bezel, you might nd that a small dot of adhesiv e is used at the top corner: 1. ...

  • Apple 13 INCH LATE 2006 - page 155

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 5 5 T o loosen the bottom of the bezel, run a black stick along the inner edge where the bezel meets the L CD frame. Do not touch the displa y face. Note: If you hav e a plastic sheet that can protect the L CD panel, cover the display fac e. Lift o the bezel. Check for an y mounting clips arou ...

  • Apple 13 INCH LATE 2006 - page 156

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 56 Return any clips back into the bez el brace. If any of the mounting clips are dicult t o install, check that they ar e struc turally sound . Y ou can order a kit of replacement clips if necessary . Install the replacement bez el (rst see notes in the Replacement Pr ocedure), and reassemb ...

  • Apple 13 INCH LATE 2006 - page 157

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 5 7 Replacement Pr ocedure Important: Before installing a replacement bez el, be sur e to check the camera area, and peel o the dust cover lm tha t comes with a new bezel. Replacement Ca ution: The lower corners of the bezel include moun ting hooks that di er in design from the snaps at ...

  • Apple 13 INCH LATE 2006 - page 158

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 58 Caution: T o install the bezel, start at the top near the camera rst. Match the two locator pins inside the bezel to the holes in the t op center of the display assembly . Pr ess to secure the top of the bezel. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 159

    MacBook (1 3-inch) T ake Apar t — Display Bez el 1 59 With the camera area secured , bend up the bottom of the bezel to hook the bottom edge of the bezel. Pr ess along the outer frame of the bezel to secure it to the dis play assembly . 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 160

    MacBook (1 3-inch) T ake Apar t — Bezel Mounting Clips 1 60 Bezel Mounting Clips T ools ESD wrist strap and mat Clean, soft, lint-free cloth Jeweler’ s atblade screwdriver Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Display bez el Part Location • • • • • • • ...

  • Apple 13 INCH LATE 2006 - page 161

    MacBook (1 3-inch) T ake Apar t — Bezel Mounting Clips 1 6 1 Removal Pr ocedure Caution: When working near the bezel brace, cov er the LCD panel with a soft cloth to a void scratching the displa y . Use a jeweler’ s atblade screwdriv er to pr y up the mounting clip . • If you are removing the clip fr om the bezel brace, pr y it up from one ...

  • Apple 13 INCH LATE 2006 - page 162

    MacBook (1 3-inch) T ake Apar t — Bezel Mounting Clips 1 62 Make sure no plastic remnants are left in the bezel brace opening fr om an old clip. If any small pieces remain, remov e them with a needlenose pliers. Replacement Pr ocedure Closely inspect the two hooks on the replacement moun ting clip. Make sure the hooks are intact at a 90-degree an ...

  • Apple 13 INCH LATE 2006 - page 163

    MacBook (1 3-inch) T ake Apar t — Bezel Mounting Clips 1 63 Pr ess the clip into place so that it is level with the bez el brace. Make sure all twelve clips t correctly in the bezel brace and that no clips r emain on the inner side of the display bez el. Install the replacement moun ting clips, and reassemble and test the computer . 3. 4. 5. ...

  • Apple 13 INCH LATE 2006 - page 164

    MacBook (1 3-inch) T ake Apar t — Spacers at Bezel Sc oops 1 6 4 Spacers at Bezel Scoops T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Display bez el Part Location • ...

  • Apple 13 INCH LATE 2006 - page 165

    MacBook (1 3-inch) T ake Apar t — Spacers at Bezel Sc oops 1 65 Pr ocedure Note the placement of the two spacers that attach to the L CD panel frame with double-sided adhesive . Replacement Note: P osition the replacement spacers v er tically so that they t into the space between the lo wer end of the bezel brace and the bezel scoop , but they ...

  • Apple 13 INCH LATE 2006 - page 166

    MacBook (1 3-inch) T ake Apar t — C-Channel 1 66 C-Channel T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Magnetic Phillips #0 screwdriver Jeweler’ s atblade screwdriver Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Opti ...

  • Apple 13 INCH LATE 2006 - page 167

    MacBook (1 3-inch) T ake Apar t — C-Channel 1 67 Pr ocedure At the top right corner of the computer assembly , remove the f ollowing screws: • 6-mm long screw from the left end of the C-channel, securing the vent cov er to the C- channel and rear panel • 3-mm long screw from the right speaker (the “holder ” for the speaker is sandwiched b ...

  • Apple 13 INCH LATE 2006 - page 168

    MacBook (1 3-inch) T ake Apar t — C-Channel 1 68 Note that the C-channel has a locator tab that ts in to the slot in the vent cov er . W edge a black stick between the right clutch block and the C-channel. Then, at the vent cover slot , use a jew eler ’ s atblade screwdriver or your ngernail to lightly tilt up the slot as you pivot the ...

  • Apple 13 INCH LATE 2006 - page 169

    MacBook (1 3-inch) T ake Apar t — C-Channel 1 69 Replacement C aution: Before installing the screws , make sure the s peak er cable is clear of the screw hole. Install the replacement C-channel, and reassemble and te st the display . 5. ...

  • Apple 13 INCH LATE 2006 - page 170

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 70 Clutch Block, Left T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Magnetic Phillips #0 screwdriver Stack of books, weight ed boxes , or other means of support for displa y while removing screws from hinge P ...

  • Apple 13 INCH LATE 2006 - page 171

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 7 1 Pr ocedure Open the display and lean it against a stack of books or bo xes that can support it when it is loosened from the display hinge . Remove the screws fr om the lef t clutch block: • 1 0-mm long thick-stemmed outer screw , closest to the left corner of the bottom case • 6-mm lo ...

  • Apple 13 INCH LATE 2006 - page 172

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 72 Remove the left clutch block from the comput er assembly . Notice that the left clutch cap comes loose when the clutch block is r emoved. M ake sure the left clutch cap is tted into the clutch block, and hold it in place when replacing the clutch block. If you are installing a new left ...

  • Apple 13 INCH LATE 2006 - page 173

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 7 3 Replacement Note: Notic e how the inverter cable and wireless antenna cable s are routed around the left display hinge . Make sure they are r outed as shown and cannot be pinched when the clutch cap and clutch block are installed . Late 2006 Model: ...

  • Apple 13 INCH LATE 2006 - page 174

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 7 4 Late 2006 Model Replacement C aution: If the inverter cable and antenna cables are not routed correctly , they can damage the delicat e logic board components located beneath the tape: Important: Before installing the clutch block, make sure the cables are routed as sho wn: ...

  • Apple 13 INCH LATE 2006 - page 175

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 7 5 Late 2006 Model: The follo wing image shows the clutch block correctly installed: Replacement Note: If the in ver ter cable had been detached to service the display , make sure to install the in ver ter cable ground scr ew to the logic board. This screw is not visible when the left clutch ...

  • Apple 13 INCH LATE 2006 - page 176

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Left 1 76 Replacement Note: If y ou are replacing the left and right clutch blocks as a pair , install the screws in the order shown. O ther wise , install the longe st outer screw rst. Replacement Note: The left clutch cap and right clutch cap are not the same. The left clutch cap is pictured be ...

  • Apple 13 INCH LATE 2006 - page 177

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Right 1 77 Clutch Block, Right T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Magnetic Phillips #0 screwdriver Stack of books (or other means of suppor t f or the display while removing screws fr om the display hinge ...

  • Apple 13 INCH LATE 2006 - page 178

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Right 1 78 Pr ocedure Remove the screws fr om the right clutch block: • 1 0-mm long thick-stemmed outer screw , closest to the right corner of the bottom case • 6-mm long thick-stemmed inner screw Use a black stick to remo ve the right clutch block from the computer assembly . 1. ...

  • Apple 13 INCH LATE 2006 - page 179

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Right 1 79 Replacement Note: Tilt the r ight end of the clutch block in to the rear panel rst. Then make sure the left end with the clutch cap aligns properly before installing the scr ews. Note: Unlike the left clutch block, there is no mesh pad on the right clutch block. Replacement Note: Notic ...

  • Apple 13 INCH LATE 2006 - page 180

    MacBook (1 3-inch) T ake Apar t — Clutch Block, Right 1 80 Replacement Note: Notic e how the L VDS cable and microphone cable are routed around the right display hinge . Mak e sure they are r outed as shown and cannot be pinched when the right clutch block and clutch cap are installed . Replacement Note: If y ou are replacing the left and right c ...

  • Apple 13 INCH LATE 2006 - page 181

    MacBook (1 3-inch) T ake Apar t — Clutch Caps 1 8 1 Clutch Caps (Refer to “Clutch Block, Left” and “Clutch Block, Right”) ...

  • Apple 13 INCH LATE 2006 - page 182

    MacBook (1 3-inch) T ake Apar t — Display Module 1 82 Display Module Note: Although the display module is not o ered as an available part, removing it is required to access all int er nal displa y par ts (exc ept the bezel). T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic at ...

  • Apple 13 INCH LATE 2006 - page 183

    MacBook (1 3-inch) T ake Apar t — Display Module 1 83 Part Location Pr ocedure F rom the logic board, disconnect the following v e connectors: • T wo wireless card an tenna cables (three wireless cables if Lat e 2006 model) • Microphone cable (located between I/O shield and left memor y slot) • L VDS cable 1. ...

  • Apple 13 INCH LATE 2006 - page 184

    MacBook (1 3-inch) T ake Apar t — Display Module 1 84 Remove the two gr ound screws that secure the cables to the midframe: • 7 .5-mm long screw near the top end • 9-mm long screw from the middle (do not remo ve if Late 2006 model) W arning: The subwoofer c one is a sensitive device. A void touching the subwoof er cone. Carefully pull up the ...

  • Apple 13 INCH LATE 2006 - page 185

    MacBook (1 3-inch) T ake Apar t — Display Module 1 85 Carefully unroute the L VDS cable and microphone cable from under the subwoofer tabs in the bottom case. Near the right hinge, remo ve the 3-mm long ground screw that anchors the L VDS cable to the upper right corner of the bottom case. 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 186

    MacBook (1 3-inch) T ake Apar t — Display Module 1 86 Near the left hinge, disconnect the inverter cable. (Late 2 006 model is shown here.) Holding the display module at the bez el, lift the module o of the computer assembly . 7. 8. ...

  • Apple 13 INCH LATE 2006 - page 187

    MacBook (1 3-inch) T ake Apar t — Display Module 1 87 Install the replacement dis play module, and reassemble and test the c omputer . Replacement Note: When installing the display , note how the cables are routed at the right side of the clutch barrel; The L VDS cable and microphone cable wrap around the back of the clutch barrel and are rout ed ...

  • Apple 13 INCH LATE 2006 - page 188

    MacBook (1 3-inch) T ake Apar t — Display Module 1 88 Replacement Note: Make sure that no cables can be pinched when installing the L VDS cable ground screw . ...

  • Apple 13 INCH LATE 2006 - page 189

    MacBook (1 3-inch) T ake Apar t — Bottom Case 1 89 Bottom Case Note: The bottom case include s the following parts: F eet that are heat-staked, so they are not remo vable Three int egral frames: slot-load bezel frame, front ba y frame, and rear frame Infrared (IR) sensor board in the fron t right corner Snubbers for hard drive T ools Soft cloth E ...

  • Apple 13 INCH LATE 2006 - page 190

    MacBook (1 3-inch) T ake Apar t — Bottom Case 1 90 I/O frame Logic board Part Location Pr ocedure When the parts listed in the “Preliminar y Steps ” have been remov ed, the remaining part is the bottom case. Replacement Note: Make sure the bottom case is clean and fr ee of dust before assembling the computer . • • ...

  • Apple 13 INCH LATE 2006 - page 191

    MacBook (1 3-inch) T ake Apar t — Bottom Case 1 9 1 Important: Mak e sure that the mushr oom-shaped rubber stando is in place where shown before installing the logic board . Note: If the rubber stando comes loose , use needlenose pliers t o install it. ...

  • Apple 13 INCH LATE 2006 - page 192

    MacBook (1 3-inch) T ake Apar t — Bottom Case 1 92 Replacement Ca ution: If any of the four bezel clips at the slot-load bez el come loose, simply inser t them back in the slots. Mak e sure all four clips ar e in place while reassembling the computer and befor e installing the top case. ...

  • Apple 13 INCH LATE 2006 - page 193

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 93 Clutch Cover T ools ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple probe tool, part number 92 2-5065) or other nonconductive nylon or plastic atblade tool Access car d (Apple par t number 9 22-7 1 72) Pr eliminary Steps Before you begin, remove Battery RAM door T ...

  • Apple 13 INCH LATE 2006 - page 194

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 94 Pr ocedure Important: The display cables might cat ch on the clutch cover at you r emove it, so proceed slowly to prev ent any cable damage. Notice the cable exits points at each side of the clutch. Refer to the cable arrangement shown when reinstalling the clutch co ver . 1. ...

  • Apple 13 INCH LATE 2006 - page 195

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 95 With the display assembly face up , remove the thr ee 4-mm long screws along the top edge of the clutch cov er . Slide an access card along the outer edge of the clut ch cover to loosen it from the dis play rear housing . 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 196

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 96 Unsnap both ends of the clutch cov er using a black stick. Holding the bundled display cables a t each end of the clutch cover , carefully unwrap them to help raise up the clutch co ver . 4. 5. ...

  • Apple 13 INCH LATE 2006 - page 197

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 97 Without straining cables, carefully pull the clutch cover o of the display assembly . Install the replacement clut ch cover , and reassemble and t est the computer . Replacement Note: The inner channel of the clutch cover includes a f oam pad that helps stabilize the inv er ter board . Do no ...

  • Apple 13 INCH LATE 2006 - page 198

    MacBook (1 3-inch) T ake Apar t — Clutch C over 1 98 Replacement C aution: Notice how the displa y cables are wrapped around the clutch. Check that they are wrapped as shown bef ore reassembling the computer . ...

  • Apple 13 INCH LATE 2006 - page 199

    MacBook (1 3-inch) T ake Apar t — Bezel Scoops 1 99 Bezel Scoops, Left and Right T ools ESD wrist strap and mat Black stick (Apple probe tool, part number 92 2-5065) or other nonconductive nylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display module Display bez ...

  • Apple 13 INCH LATE 2006 - page 200

    MacBook (1 3-inch) T ake Apar t — Bezel Scoops 200 Pr ocedure With the bezel spacers r emoved, use a black stick to loosen the outer edge of the bezel scoop and push it towar d the display face. Repeat f or the other bezel scoop. Replacement Note: Bef ore replacing the bezel scoops , make sure that the cable s that are routed under the bezel sc o ...

  • Apple 13 INCH LATE 2006 - page 201

    MacBook (1 3-inch) T ake Apar t — Bezel Scoops 20 1 Late 2005 Model: Replacement Note: On the underside of each bez el scoop, note that the thr ee raised tabs match up with the three slots in the dis play hinge. Align the tabs to the slots. ...

  • Apple 13 INCH LATE 2006 - page 202

    MacBook (1 3-inch) T ake Apar t — Bezel Scoops 202 Replacement Note: W ith the cables tucked in, slide on the bezel scoop . ...

  • Apple 13 INCH LATE 2006 - page 203

    MacBook (1 3-inch) T ake Apar t — L CD P anel 203 LCD Panel T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Flashlight or bright lamp Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s Hard driv e ...

  • Apple 13 INCH LATE 2006 - page 204

    MacBook (1 3-inch) T ake Apar t — L CD P anel 204 Part Location Pr ocedure With all of the preliminary steps per formed, tur n ov er the LCD panel and check f or any remaining strips of tape. 1. ...

  • Apple 13 INCH LATE 2006 - page 205

    MacBook (1 3-inch) T ake Apar t — L CD P anel 205 Install the replacement L CD panel, and reassemble and test the c omputer . Replacement Note: When reassembling the computer , make sure the L CD cable is bent, but not pinched or damaged. 2. ...

  • Apple 13 INCH LATE 2006 - page 206

    MacBook (1 3-inch) T ake Apar t — L CD P anel 206 Replacement Note: S tar t by connecting the L VDS cable and USB ex line rst. T hen place the tape before con tinuing with the rest of the reassembly . Late 2006 Model: ...

  • Apple 13 INCH LATE 2006 - page 207

    MacBook (1 3-inch) T ake Apar t — L CD P anel 207 Important: Notice the correct horizontal placement of the tape. If placed ver tically , the tape can be visible through the Apple logo on the displa y rear housing. Before r eassembling the display , check the back of the L CD panel to make sure the tape is placed horizontally , as shown. With the ...

  • Apple 13 INCH LATE 2006 - page 208

    MacBook (1 3-inch) T ake Apar t — L CD P anel 208 Late 2006 Model Replacement Not e: For the Late 2 006 model, there are three possible panel manufacturers: AUO , Chi Mei, and Samsung . Refer to the following table when replacing the L CD panel and/or the L VDS cable: If you are replacing the L CD panel, be sure to also replace the L VDS cable an ...

  • Apple 13 INCH LATE 2006 - page 209

    MacBook (1 3-inch) T ake Apar t — Antenna Recept ors and Cables, T op and Left 209 Antenna Receptors and Cables, T op and Left T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Jeweler’ s atblade screwdriver Pr elimina ...

  • Apple 13 INCH LATE 2006 - page 210

    MacBook (1 3-inch) T ake Apar t — Antenna Recept ors and Cables, T op and Left 2 1 0 Part Location Pr ocedure Notice that the antenna cable s are two separate cables (black and gra y) that run along the left front side of the L CD panel brace . The gray cable is also routed ov er the top corner of the L CD panel. Carefully unroute the cable s fro ...

  • Apple 13 INCH LATE 2006 - page 211

    MacBook (1 3-inch) T ake Apar t — Antenna Recept ors and Cables, T op and Left 2 1 1 Remove the three iden tical 3-mm long screws from the left brace. Rotate the top corner of the L CD panel and remov e the 3-mm long screw from the left brace and camera bracket. 2. 3. ...

  • Apple 13 INCH LATE 2006 - page 212

    MacBook (1 3-inch) T ake Apar t — Antenna Recept ors and Cables, T op and Left 2 1 2 Slightly lift up the end of the camera bracket to free the locator pin on the end of the left brace. Replacement Note: T o avoid straining cable s, be sure to align the locator pin and hole before sliding on the left brace . Move the left brace awa y from the L C ...

  • Apple 13 INCH LATE 2006 - page 213

    MacBook (1 3-inch) T ake Apar t — Antenna Recept ors and Cables, T op and Left 2 1 3 Replacement Note: Secure the an tenna receptors by placing them ov er the recessed brace area and pressing only on the metal f old. Y ou will hear an audible snap when they are installed. Install the replacement an tenna cables, and reassemble and test the c ompu ...

  • Apple 13 INCH LATE 2006 - page 214

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 4 Antenna Receptor and Cable, Right (Late 2006 Model Only) T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Jeweler’ s atblade screwdriver Pr el ...

  • Apple 13 INCH LATE 2006 - page 215

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 5 Pr ocedure Note the path of the blue ant enna cable as it runs along the bottom of the display rear housing, under neath the microphone cable , and up the right side of the display . 1. ...

  • Apple 13 INCH LATE 2006 - page 216

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 6 F ollowing the order shown, remove the twelv e identical 4.5-mm long screws around the frame of the L CD panel. Caution: T o prevent scra tches or other cosmetic damage to the display housing , use a soft cloth as a protective lay er when removing the screws. Replacement N ...

  • Apple 13 INCH LATE 2006 - page 217

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 7 Note: The top of the dis play includes four thin, clear strips of double-sided tape. These ar e the camera spacers that ar e discussed later in this chapter . Be sure to reinstall them if they become loose. Without straining the blue antenna cable , tilt up the LCD panel. ...

  • Apple 13 INCH LATE 2006 - page 218

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 8 Remove the strip of tape that wraps the noninsulat ed sec tion of the antenna cable bundle . Replacement Note: Be sure to wrap the cables with a new strip of tape when reassembling the display . 4. ...

  • Apple 13 INCH LATE 2006 - page 219

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 2 1 9 Thread the blue ant enna cable from left to right out of the lef t end of the displa y rear housing. At the right displa y hinge, thread the blue antenna cable from left to right out of the right end of the display r ear housing. 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 220

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 220 With the blue antenna cable free from the dis play rear housing , r emove the L CD panel assembly and place it face down on a soft clean cloth. Carefully unroute the silv er colored microphone cable and the blue antenna cable from the right brace. Remove the two iden tical s ...

  • Apple 13 INCH LATE 2006 - page 221

    MacBook (1 3-inch) T ake Apar t — Antenna Recept or and Cable, Right 22 1 Important: T o suppor t the solder joint wher e the cable meets the receptor , keep the antenna cable in the last brace tab while loosening the r eceptor from the brace. Caution: The antenna receptor is friction-t with a metal fold that hooks ont o the right brace. T he ...

  • Apple 13 INCH LATE 2006 - page 222

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 222 LCD Panel Assembly Important: Although the L CD panel assembly is not an available subassembly part, it must be removed t o replace other display parts. T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple probe tool, part number 92 2-5065) or othe ...

  • Apple 13 INCH LATE 2006 - page 223

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 223 Part Location ...

  • Apple 13 INCH LATE 2006 - page 224

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 224 Removal Pr ocedure Important: Study the cable routing around each hinge carefully . When reinstalling the L CD panel assembly for your rst time , this can be a trick y area Note: Although the images show the in verter board installed, it should be remov ed previously as listed in the p ...

  • Apple 13 INCH LATE 2006 - page 225

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 225 F ollowing the order shown, remove the twelv e identical 4.5-mm long screws around the frame of the L CD panel. Caution: T o prevent scra tches or other cosmetic damage to the display housing , use a soft cloth as a protective lay er when removing the screws. 2. ...

  • Apple 13 INCH LATE 2006 - page 226

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 226 F or the original M acBook model, remov e the 3-mm long ground screw from both display hinges. F or the Late 2006 model, remo ve the 3-mm long ground screw from the left hinge only . Note: Although the images show the in verter board installed, it should be remov ed previously as listed i ...

  • Apple 13 INCH LATE 2006 - page 227

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 227 F or the Late 2006 model only , tilt up the L CD panel just enough to remove the left hinge. Refer to the section “Display Hinges , Left and Right. ”T he blue wireless antenna cable is routed under the left hinge. Starting at the bottom corners, lift the LCD panel with fr ame and atta ...

  • Apple 13 INCH LATE 2006 - page 228

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 228 Note: The top of the camer a bracket includes four thin, clear strips of double-sided tape. These are the camer a spacers that are discussed later in this chapt er . Be sure to reinstall them if they become loose. Note: The magnets locat ed in the display rear housing may come loose while ...

  • Apple 13 INCH LATE 2006 - page 229

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 229 Set aside the L CD panel assembly so that the display is face-up if y ou are replacing any of its par ts or an y par ts remaining in the display r ear housing. Reinstall the L CD panel assembly as follows. Reinstallation Pr ocedure Important: Correctly positioning the L CD panel assembly ...

  • Apple 13 INCH LATE 2006 - page 230

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 230 Check the underside of the L CD panel assembly to make sure all cables are connected and routed properly: • L VDS cable • USB line to camera board • Black and gray ant enna receptor cables • Microphone cable 1. ...

  • Apple 13 INCH LATE 2006 - page 231

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 23 1 Important: Notice the correct horizontal placement of the tape. If placed ver tically , the tape can be visible through the Apple logo on the displa y rear housing. Before r eassembling the display , check the back of the L CD panel to make sure the tape is placed horizontally , as shown ...

  • Apple 13 INCH LATE 2006 - page 232

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 232 Check the display r ear housing to make sure it includes the three magnets: • Sleep magnet on side • T wo magnet pairs on top Important: Inser t the top corners of the L CD panel assembly into the displa y rear housing rst. Use the notch in each bezel brac e to help hold the cables ...

  • Apple 13 INCH LATE 2006 - page 233

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 233 Set the magnets back into place if they come loose during this step . With the top corners secured , tilt up the bottom corners or the L CD panel assembly to route the antenna rec eptor cables and microphone cable around the recessed channel between the display hinge and the r ear housing ...

  • Apple 13 INCH LATE 2006 - page 234

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 234 Important: The notch on each bezel brace indicat es the point at which the cables start their path around the displa y hinge. Use a black stick at that notch to make sure the cables ar e not pinched and to guide them into the r ecessed channel. ...

  • Apple 13 INCH LATE 2006 - page 235

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 235 Carefully pull the cables to make sure ther e is no slack as they route through the channels. At the lower left corner , mak e sure the cable s are routed as shown: • Microphone cable routes along the outer edge of the bez el brace • L CD panel cable tucks under L VDS cable • L VDS ...

  • Apple 13 INCH LATE 2006 - page 236

    MacBook (1 3-inch) T ake Apar t — L CD P anel Assembly 236 With the magnets and cables in place , slightly r eposition the LCD panel assembly , if necessary , so that the bezel braces t o ver the two locator pins (one pin at each side of the rear housing). Starting with the screw holes just above the locator pins , install the 1 2 screws in th ...

  • Apple 13 INCH LATE 2006 - page 237

    MacBook (1 3-inch) T ake Apar t — F oil at Camera Bracket 23 7 Foil at Camera Bracket (Original MacBook Model) T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s Hard driv e T op ca ...

  • Apple 13 INCH LATE 2006 - page 238

    MacBook (1 3-inch) T ake Apar t — F oil at Camera Bracket 238 Pr ocedure Note the placement of the f oil strip that attaches to the camera bracket with an adhesive backing. Using a black stick, carefully peel up the foil strip . P osition the replacement foil strip so that its r ound opening does not block any par t of the round area for the micr ...

  • Apple 13 INCH LATE 2006 - page 239

    MacBook (1 3-inch) T ake Apar t — F oil at Camera Bracket 239 Lightly tap down on the foil so it adher es completely to the camera bracket.. P eel up the adhesive paper so that the foil r emains on the camera bracket. . Reassemble and test the computer . 4. 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 240

    MacBook (1 3-inch) T ake Apar t — Spacers at Camera B racket 240 Spacers at Camera Bracket T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s Hard driv e T op case with keyboard Opt ...

  • Apple 13 INCH LATE 2006 - page 241

    MacBook (1 3-inch) T ake Apar t — Spacers at Camera B racket 24 1 Pr ocedure Note the placement of the f our thin, clear strips that attach to the camera bracket with double-sided adhesive . Using a black stick, remove the f our strips. Replacement Note: P osition the replacement adhesive strips so that they extend slightly over the camera bracke ...

  • Apple 13 INCH LATE 2006 - page 242

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 242 Camera Assembly T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door Memory c ard s Hard driv e T op case with ...

  • Apple 13 INCH LATE 2006 - page 243

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 243 Part Location Pr ocedure With the L CD panel face-down on a clean, soft cloth, disconnec t the USB camera cable (pull the connector straight down). Remove the two 2-mm long scr ews from the camera board. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 244

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 244 Tilt up the camera board and use a black stick to gently pry up the microphone cable gasket from the panel frame. Replacement Note: Make sure the microphone gasket ts snug in the frame and that the microphone cable runs along the top of the camera frame bef ore installing the screws. 3. ...

  • Apple 13 INCH LATE 2006 - page 245

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 245 P eel up the single strip of tape that holds the microphone cable in place at the camera bracket. Replacement Note: Be sure to install a replacement strip of tape to hold the microphone cable in place and keep the cable away from ar eas where it could be pinched when the panel is reinstalled. ...

  • Apple 13 INCH LATE 2006 - page 246

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 246 Lift o the camera bracket from the locator pins on the bez el braces. Do not remove the camera board from the bracket. Install the replacement camera assembly , and reassemble and test the computer . 6. 7. ...

  • Apple 13 INCH LATE 2006 - page 247

    MacBook (1 3-inch) T ake Apar t — Camera Assembly 24 7 Replacement Note: The camera assembly includes: Camera bracket Camera board Camera in plastic case Flex cable from camer a case to camera board Screws Replacement Note: Be sur e to reinstall the microphone in the gasket before securing the 2-mm long camera board screws. Replacement Note: When ...

  • Apple 13 INCH LATE 2006 - page 248

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 248 L VDS Cable with USB Line T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool P ermanent mark ing , felt-tip pen Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keybo ...

  • Apple 13 INCH LATE 2006 - page 249

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 249 Part Location Pr ocedure Note the placement of the strips of tape that secure the L VDS cable and the USB line to the L CD panel. 1. ...

  • Apple 13 INCH LATE 2006 - page 250

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 250 Because the protective sheath f or the ex cables can be delicate, use light pressure to hold the cables in place as you car efully peel up the strips of tap e just enough to fr ee the cables. Disconnect the L VDS cable by pulling the connector straight down from the connector on t ...

  • Apple 13 INCH LATE 2006 - page 251

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 25 1 Disconnect the USB line by using a black stick and your ngernail to slide the connector straight down from the camera boar d. Replacement Note: When reinstalling the USB line, no copper contacts should be visible. Reinstall the cable if you can see copper contacts. • Wrong • ...

  • Apple 13 INCH LATE 2006 - page 252

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 252 Remove the L VDS cable from the panel, and unwrap the black tape tha t secures the cable to the microphone cable. Replacement Note: Whenever the microphone cable is to be separated from the L VDS cable, use a permanent marking pen to mark the microphone cable. Mark ing the cable wher ...

  • Apple 13 INCH LATE 2006 - page 253

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 253 Install the replacement L VDS cable with USB line, and reassemble and test the computer . 6. ...

  • Apple 13 INCH LATE 2006 - page 254

    MacBook (1 3-inch) T ake Apar t — L VDS Cable with USB Line 254 Late 2006 Model Replacement Not e: For the Late 2 006 model, there are three possible panel manufacturers: AUO , Chi Mei, and Samsung . Refer to the following table when replacing the L VDS cable or L CD panel: If you are replacing just the L VDS cable but not the panel, be sure t o ...

  • Apple 13 INCH LATE 2006 - page 255

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 25 5 Microphone Cable T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool P ermanent mark ing , felt-tip pen Pr eliminary Steps Before you begin, remove Battery RAM door T op ...

  • Apple 13 INCH LATE 2006 - page 256

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 256 Part Location Pr ocedure Note the routing of the microphone cable as it runs along the right edge of the L CD panel. 1. ...

  • Apple 13 INCH LATE 2006 - page 257

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 25 7 Pull up the cable from the r outing tabs. P eel up the single strip of tape that holds the microphone cable in place at the camera bracket. Replacement Note: Be sure to install a replacement strip of tape to hold the microphone cable in place and keep the cable away from ar eas where it coul ...

  • Apple 13 INCH LATE 2006 - page 258

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 258 Remove the two 3-mm long scr ews from the camera board. Without straining the camera board cable , car efully tilt up the camera board to access the microphone that is tted int o the opening in the camera bracket. Use a black stick to pull up the microphone from the gasket. 4. 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 259

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 259 Replacement Note: Install the micr ophone in the gasket and use a black stick to press it down so it is level with the edge of the gasket. Unwrap the black tape that secures the micr ophone cable with the L VDS cable. 7. ...

  • Apple 13 INCH LATE 2006 - page 260

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 260 Replacement Note: Whenever the microphone cable is to be separated from the L VDS cable, use a permanent marking pen to mark the microphone cable. Mark ing the cable where the strips of conductive tape overlap the microphone cable pro vides a guide for reassembly . Install the replacement mic ...

  • Apple 13 INCH LATE 2006 - page 261

    MacBook (1 3-inch) T ake Apar t — Microphone Cable 26 1 Important: Where the microphone cable exits the displa y rear housing, the microphone cable must be pulled taught within the cable bundle exiting the displa y . If it ’ s too loose or too tight, it could get pinched during displa y reassembly . ...

  • Apple 13 INCH LATE 2006 - page 262

    MacBook (1 3-inch) T ake Apar t — Inv er ter Board 262 Inverter Board T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display module Display bez el Clutch ...

  • Apple 13 INCH LATE 2006 - page 263

    MacBook (1 3-inch) T ake Apar t — Inv er ter Board 263 Pr ocedure Caution: During this procedur e, do not press on the at area of the board or on its c omponents. Handle the board by the edges only . Using a black stick or your ngers , disc onnec t the in ver ter cable from the left end of the board. Disconnect the L CD panel cable from the ...

  • Apple 13 INCH LATE 2006 - page 264

    MacBook (1 3-inch) T ake Apar t — Inv er ter Board 264 Holding the board by the ends , lift out the in ver ter board from the slot in the dis play rear housing. Install the replacement in ver ter boar d, and reassemble and test the comput er . 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 265

    MacBook (1 3-inch) T ake Apar t — Inv er ter Cable 265 Inverter Cable T ools Soft cloth ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display module Display bez el Clutch ...

  • Apple 13 INCH LATE 2006 - page 266

    MacBook (1 3-inch) T ake Apar t — Inv er ter Cable 266 Pr ocedure With the display assembly re sting on a clean, soft cloth, note the position of the in ver ter cable in relation to the left clutch barrel. Remove the tape from the left clutch barrel. Remove the 3-mm long ground scr ew, and disconnec t the in ver ter cable from the left end of the ...

  • Apple 13 INCH LATE 2006 - page 267

    MacBook (1 3-inch) T ake Apar t — Inv er ter Cable 267 Remove the in ver ter cable from the dis play assembly . Replace the inv er ter cable, and reassemble and test the computer Replacement Note: Apply the tape where shown to secure the in ver ter cable to the left hinge. 4. 5. ...

  • Apple 13 INCH LATE 2006 - page 268

    MacBook (1 3-inch) T ake Apar t — Display Hinge s 268 Display Hinges, Left and Right T ools Soft cloth Magnetic Phillips #0 screwdriver Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display modul ...

  • Apple 13 INCH LATE 2006 - page 269

    MacBook (1 3-inch) T ake Apar t — Display Hinge s 269 Pr ocedure With the display housing on a soft cloth, remove the thr ee identical 4-mm long screws along the lower “ arm” of each hinge. Use a black stick to carefully pry up each hinge from the double-sided tape holding it to the display r ear housing. 1. 2. ...

  • Apple 13 INCH LATE 2006 - page 270

    MacBook (1 3-inch) T ake Apar t — Display Hinge s 270 Replacement Note: When installing new hinges, peel o the adhesive backing and align the hinges over the scr ew standos in the display rear housing . Install the replacement dis play hinges, and reassemble and te st the computer . 3. ...

  • Apple 13 INCH LATE 2006 - page 271

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Left 27 1 Bezel Brace, Left The L-shaped bezel brace a ttaches to the left side of the LCD panel and include s integral tabs for the AirP or t antenna cable r outing. T ools With the preliminary steps completed, no tools are r equired for this procedure . Pr eliminary Steps Before you begin, remove ...

  • Apple 13 INCH LATE 2006 - page 272

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Left 272 Part Location Pr ocedure With the wireless antenna r eceptors removed , the left bezel brace is loose from the L CD panel assembly . F ollow the replacement instructions in “ Antenna Receptors and Cable s” to attach the cables before installing the replac ement left bezel brace. Then re ...

  • Apple 13 INCH LATE 2006 - page 273

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Right 27 3 Bezel Brace, Right The L-shaped bezel brace a ttaches to the right side of the L CD panel and includes integral tabs for the microphone cable routing . T ools Soft cloth ESD wrist strap and mat Magnetic Phillips #0 screwdriver Black stick (Apple probe tool, part number 92 2-5065) or other ...

  • Apple 13 INCH LATE 2006 - page 274

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Right 27 4 Part Location Pr ocedure Caution: Do not pre ss on the LCD panel during this proc edure. Pre ssing on the panel could damage the internal circuitry . Note how the microphone cable is r outed through the tabs on the right bezel brace. 1. ...

  • Apple 13 INCH LATE 2006 - page 275

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Right 27 5 Without straining the microphone cable , use a black stick t o loosen it from the tabs. Remove the three iden tical 3-mm long screws (these can be identied by the small screw head) from the right side of the L CD panel. Remove the 3-mm long camera bracket screw . 2. 3. 4. ...

  • Apple 13 INCH LATE 2006 - page 276

    MacBook (1 3-inch) T ake Apar t — Bezel Brac e, Right 27 6 Without straining the USB ex cable, tilt up the camera bracket and remove the right bezel brace from the L CD panel assembly . Install the replacement right bez el brace, and reassemble and test the c omputer . 5. 6. ...

  • Apple 13 INCH LATE 2006 - page 277

    MacBook (1 3-inch) T ake Apar t — Sleep Magnet 277 Sleep Magnet T ools Soft cloth Black stick (Apple probe tool, part number 92 2-5065) or other nonconductive nylon or plastic atblade tool Jeweler’ s atblade screwdriver Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display module Displa ...

  • Apple 13 INCH LATE 2006 - page 278

    MacBook (1 3-inch) T ake Apar t — Sleep Magnet 278 Part Location Pr ocedure With the display rear housing on a soft cloth, note the position of the sleep magnet rece ssed in the left side of the housing. Using a black stick or a jeweler’ s atblade screwdriv er , inser t the tip of the black stick or screwdriver in the tin y opening under the ...

  • Apple 13 INCH LATE 2006 - page 279

    MacBook (1 3-inch) T ake Apar t — Sleep Magnet 27 9 Install the replacement sleep magnet , and r eassemble and test the computer . 3. ...

  • Apple 13 INCH LATE 2006 - page 280

    MacBook (1 3-inch) T ake Apar t — Display Magnet P airs 280 Display Magnet Pairs T ools Soft cloth Black stick (Apple probe tool, part number 92 2-5065) or other nonconductive nylon or plastic atblade tool Jeweler’ s atblade screwdriver Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Disp ...

  • Apple 13 INCH LATE 2006 - page 281

    MacBook (1 3-inch) T ake Apar t — Display Magnet P airs 28 1 Part Location Pr ocedure With the display rear housing on a soft cloth, note the position of the magnet pairs rece ssed in the top corners of the displa y rear housing. If the magnet pairs are tight in the slots, use a black stick or a jeweler’ s atblade screw driver to remov e the ...

  • Apple 13 INCH LATE 2006 - page 282

    MacBook (1 3-inch) T ake Apar t — Display Magnet P airs 282 Install the replacement dis play magnet pairs, and reassemble and test the c omputer . Replacement Note: Make sure a metal shunt is a ttached and correctly aligned to the base of each magnet pair . The magnet pairs are int erchangeable between the left and right side of the display r ear ...

  • Apple 13 INCH LATE 2006 - page 283

    MacBook (1 3-inch) T ake Apar t — Display Magnet P airs 283 Replacement Note: When installing the LCD panel assembly , the magnets may be drawn to the metal frame and become loose. M ake sure they are tted back in the r ear housing before tightening any scr ews on the LCD panel assembly . ...

  • Apple 13 INCH LATE 2006 - page 284

    MacBook (1 3-inch) T ake Apar t — Display Rear Housing 284 Display Rear Housing T ools Soft cloth Pr eliminary Steps Before you begin, remove Battery RAM door T op case with keyboard Optical drive Display module Display bez el Clutch co ver Spacers at bezel sc oops Bezel scoops Inv er ter board L CD panel assembly Display hinge s, left and right ...

  • Apple 13 INCH LATE 2006 - page 285

    MacBook (1 3-inch) T ake Apar t — Display Rear Housing 28 5 Part Location Pr ocedure When all of the parts listed in the preliminar y steps are remo ved, the remaining part is the display r ear housing. 1. ...

  • Apple 13 INCH LATE 2006 - page 286

    MacBook (1 3-inch) T ake Apar t — Display Rear Housing 286 Replacement Note: When reassembling the LCD panel assembly in the dis play rear housing , make sure the magnet pairs and sleep magnet are secured in place . Reassemble and test the computer . Replacement Note: The display rear housing comes with the pr e-installed Apple logo, sponge pads, ...

  • Apple 13 INCH LATE 2006 - page 287

     Service Source © 2006, 2007 Apple Inc . All rights re ser ved. Additional Procedures MacBook (13-inch) ...

  • Apple 13 INCH LATE 2006 - page 288

    MacBook (1 3-inch) Additional Proc edures — General Information 288 General Information Notes on Replacing Keycaps When a key on the keyboard need replacement, you can a void the cost of replacing a whole top case by just replacing a keycap . The method for replacing keys depends on the type of keyboard and the manufacturer . This chapter provide ...

  • Apple 13 INCH LATE 2006 - page 289

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 2 89 Replacing Darfon Keycaps T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Fine-poin t tweezers Needlenose pliers Pr eliminary Steps Before you begin, remove the battery . Part Location Pr ocedure Th ...

  • Apple 13 INCH LATE 2006 - page 290

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 290 Removing and Replacing a Square Key 1 . If a key needs to be removed (f or example, if a key is stick ing when pre ssed), alwa ys pr y it up from the left side—either the upper or lower left corner . 2. Because adhesive is used under the top case , closely inspect the case for a ...

  • Apple 13 INCH LATE 2006 - page 291

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 29 1 3. T est the operation of the scissor mechanism by using a black stick to car efully raise and lower the mechanism. • If it is installed correctly , the scissor should move smoothly . • If it is loose, remov e it and compare the two par ts of the scissor mechanism to the imag ...

  • Apple 13 INCH LATE 2006 - page 292

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 29 2 4. Check the underside of the keycap for two clips on one side and two hooks on the other side . • If any of the hooks or clips are bent, broken, or missing , replace the keycap. • If the hooks and clips are intact, re-use the keycap . 5 . Check the rubber dome and raised met ...

  • Apple 13 INCH LATE 2006 - page 293

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 29 3 6. With the scissor mechanism open, install the slider bar under the metal hook of the t op case. ...

  • Apple 13 INCH LATE 2006 - page 294

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 294 7 . Allow the scissor mechanism to f old at and hold the slider bar in place while using a black stick to insert the scissor pins—one at a time—into the top case ears. 8. With the scissor pins inser ted , use a black stick t o raise and lower the scissor mechanism to make s ...

  • Apple 13 INCH LATE 2006 - page 295

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 29 5 9 . Moving from left to right, slide the right end of the keycap into the keycap well so that the hooks inside the right side of the keycap latch onto the pins on the right side of the scissor mechanism. 1 0. P ress down on the left side of the key until the keycap snaps into pla ...

  • Apple 13 INCH LATE 2006 - page 296

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 296 Reassembling the Scissor Mechanism If the two pieces of a scissor mechanism come apart, • Check that the pieces are not damaged . The image below shows the separate scissor piec es and the fully assembled scissor mechanism. • Flex the out er piece to install the pins of the in ...

  • Apple 13 INCH LATE 2006 - page 297

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 29 7 2. Because adhesive is used under the top case , closely inspect the case for any adhesiv e that may hav e built up under the keycap. Lift away an y built-up adhesive using ne-point tweezers . 3. T est the operation of the scissor mechanism by using a black stick to car efully ...

  • Apple 13 INCH LATE 2006 - page 298

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 298 - When closed, its prole should be fully at. - The slider bar and all four pins should be intact. 4. Inspect the rows of clips on the underside of the keycap . • If any of the clips are bent , br ok en, or missing , r eplace the keycap. • If the clips are intact, re-use ...

  • Apple 13 INCH LATE 2006 - page 299

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 299 5 . Check the rubber dome and raised metal areas inside the keycap opening on the top case. • When the rubber dome is pressed and released , it should spring back upright. If the rubber dome is o cen ter or damaged, replace the top case . • If the metal hook that holds the ...

  • Apple 13 INCH LATE 2006 - page 300

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 300 7 . Allow the scissor mechanism to f old at and hold the slider bar in place while using a black stick to insert the scissor pins—one at a time—into the top case ears. 8. With the scissor pins inser ted , use a black stick t o raise and lower the scissor mechanism to make s ...

  • Apple 13 INCH LATE 2006 - page 301

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 30 1 9 . Check the keycap well area on the top case . If the bottom stabiliz er bar is pushed up, move it down as far as it will go . 1 0. Determine which is the top of the Space bar key cap by check ing the clips on the inner plane. The top of the keycap has the ro w of clips that ex ...

  • Apple 13 INCH LATE 2006 - page 302

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 302 1 1 . Align the bottom row of clips inside the bott om edge of the keycap with the bottom stabilizer bar . 1 2. P ress and slide your nger along the bottom of the Space bar o ver the bottom stabilizer bar until you hear the clips click int o place. ( The keycap is tilted up at ...

  • Apple 13 INCH LATE 2006 - page 303

    MacBook (1 3-inch) Additional Proc edures— Dar fon Keycaps — 303 1 4. Press the length of the Space bar t o ensure all clips are secure. 1 5. Check the key from all angles to make sure it is uniformly at. Press and release one corner of the key . If the key is installed correc tly , the opposit e corner should respond at the same level (not ...

  • Apple 13 INCH LATE 2006 - page 304

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 304 Replacing Mitsumi Keycaps T ools ESD wrist strap and mat Black stick (Apple part number 922-5065) or other nonc onduc tive n ylon or plastic atblade tool Fine-poin t tweezers Needlenose pliers Pr eliminary Steps Before you begin, remove the battery . Part Location The Mitsumi ...

  • Apple 13 INCH LATE 2006 - page 305

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 305 ISO Keyboard Layout: JIS Keyboard Layout: Pr ocedure Like the Dar fon keyboard , the M itsumi keyboard is integr ated in the top case and cannot be removed fr om the top case. The Mitsumi keyboard comes in three versions: ANSI, ISO , and JIS. T he square keycaps for all three v e ...

  • Apple 13 INCH LATE 2006 - page 306

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 306 hinge mechanism and one stabilizer bar; whereas the ISO and JIS Return k eycap has no hinge mechanism and three stabilizer bars. Important T ips: Before installing a new keycap , make sure The clips on the underside of the keycap are not broken or bent. The hinge mechanism operat ...

  • Apple 13 INCH LATE 2006 - page 307

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 307 3. Note the stabilizer bar and clips on the underside of the keycap, and check that the dual-hinge mechanism lays at. 4. T est the operation of the dual-hinge mechanism b y using a black stick to carefully raise and lower the mechanism. If it is installed correctly , the hinge ...

  • Apple 13 INCH LATE 2006 - page 308

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 308 5 . Check that the stabilizer bar can pivot easily within the hooked ends of the keycap. If any of the hooks or clips are bent, broken, or missing , replace the keycap. If the hooks and clips are intact, re-use the keycap . 6. Check the rubber dome inside the keycap opening on th ...

  • Apple 13 INCH LATE 2006 - page 309

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 309 7 . With the stabilizer bar open, press the two ends of the slider bar into the slots in the keycap well so they snap into plac e. 8. Allow the dual-hinge mechanism to fold a t, and use a black stick to make sure the hinged pieces are pushed farthest away fr om the rubber dome ...

  • Apple 13 INCH LATE 2006 - page 310

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 0 9 . Carefully lower the keycap on to the top case, and press do wn on the center of the key until the keycap snaps into place . 1 0. Check the key from all angle s to make sure it is uniformly at. Press and r elease the key repeatedly to v erify that it springs back each tim ...

  • Apple 13 INCH LATE 2006 - page 311

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 1 Reassembling the Hinge Mechanism This procedure sho ws images from a JIS keyboard; how ever , the steps for replacing the hinge mechanism are the same for an y versions of the Mitsumi k eycaps . 1 .If a hinge piece becomes loose from the t op case, check that the hinge piece is ...

  • Apple 13 INCH LATE 2006 - page 312

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 2 2. Check both sides of the hinge piece. Note that the top plane of the hinge piece has two barely visible recessed circle s, and the end pins t into the hooked slots on the anchored plane inside the keycap well. 3. With the hinge piece held v er tically , position it into th ...

  • Apple 13 INCH LATE 2006 - page 313

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 3 Removing and Replacing an ANSI or ISO Space Bar 1 . If a Space bar needs to be remov ed (for example, if it is sticking when pressed), pr y it up from the top edge rst. 2. With the top edge loosened, pry up the Space bar from the lower edge. Use a black stick, if necessary , ...

  • Apple 13 INCH LATE 2006 - page 314

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 4 3. Because adhesive is used under the top case , closely inspect the case for any adhesive tha t may have built up under the keycap . Lift away any built-up adhesiv e using ne-point tweezers. 4. Check that the longest stabilizer bar can piv ot easily within the four hooks of ...

  • Apple 13 INCH LATE 2006 - page 315

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 5 6. With the stabilizer bar open, make sure the two ends of the slider bar are secured into the slots in the keycap well. 7 . Make sure the single-hinge mechanism on both ends of the keyboard well is fully at and pressed as far as it will go awa y from the rubber dome. Then l ...

  • Apple 13 INCH LATE 2006 - page 316

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 6 Removing and Replacing a JIS Space Bar 1 . If a Space bar needs to be remov ed (for example, if it is sticking when pressed), pr y it up from the top edge rst. 2. With the top edge loosened, pry up the Space bar from the lower edge. Use a black stick, if necessary , to tilt ...

  • Apple 13 INCH LATE 2006 - page 317

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 7 3. Because adhesive is used under the top case , closely inspect the case for any adhesive tha t may have built up under the keycap . Lift away any built-up adhesiv e using ne-point tweezers. 4. Check that the longest stabilizer bar can piv ot easily within the three hooks o ...

  • Apple 13 INCH LATE 2006 - page 318

    MacBook (1 3-inch) Additional Proc edures — Mitsumi Keycaps — 3 1 8 7 . Make sure the dual-hinge mechanism on both ends of the keyboard well is fully at and pressed as far apart they will go. Then lower the key cap so that the clips align with the smaller stabilizer bar and the cent er of the hinge mechanism. 8. Low er the k ey down. 9 . Pre ...

  • Apple 13 INCH LATE 2006 - page 319

     Service Source © 2006, 2007 Apple Inc . All rights re ser ved. T roubleshooting MacBook (13-inch) ...

  • Apple 13 INCH LATE 2006 - page 320

    MacBook (1 3-inch) Tr oubleshooting — General Information 320 General Information The kinds of problems you might see when troubleshooting this comput er include: Unit Unusually Hot Disc Will Not Eject Microsoft Oce Applications Will Not Ope n Windows XP Will Not Install Correctly Computer Will Not Start, LED Blinks Optical Drive Does Not W or ...

  • Apple 13 INCH LATE 2006 - page 321

    MacBook (1 3-inch) Tr oubleshooting — Steps 32 1 T roubleshooting Steps Y ou per form the rst few steps of trouble shooting regardless of whether there is a repairable problem or damage. Gather Information Gather the normal information about the problem. (If you are not familiar with the normal information to gather , or any of the other steps ...

  • Apple 13 INCH LATE 2006 - page 322

    MacBook (1 3-inch) Tr oubleshooting — Steps 322 Resear ch If you have not loca ted the trouble following the steps thus far , tr y researching the symptoms . Research resour ces include: Symptom Charts section of this manual GSX gsx.apple.com Enter serial number and click Co verage Check Ser vice Source ser vice .info.apple .com Check Quick Links ...

  • Apple 13 INCH LATE 2006 - page 323

    MacBook (1 3-inch) Tr oubleshooting — Steps 323 Note: F or the current list of Do-It-Y ourself par ts , see the pr oduc t support website. V erify the Repair T o verify the repair : T r y to recr eate the original symptoms. Y ou should not be able to. (If you can, return to the beginning of the troubleshooting ow char t.) P er form the prev en ...

  • Apple 13 INCH LATE 2006 - page 324

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 32 4 Symptom Charts When to Use the Symptom Charts Before turning to the symptom charts, you should hav e completed the following steps on the Apple General T roubleshooting Flo wchar t: Gather information V erify the problem T r y quick x es Y ou consult the symptom char ts as part of the R ...

  • Apple 13 INCH LATE 2006 - page 325

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 32 5 Reseat AirP ort Ex treme and Bluetooth ant enna cables on cards. Check AirP or t Extreme and Bluetooth antenna cable s for damage. Replace with known-good AirP or t Extreme Card or Bluetooth card . Replace AirP or t Extreme or Bluetooth antenna cable s. Unit unusually hot This computer run ...

  • Apple 13 INCH LATE 2006 - page 326

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 326 F or more information on the operating temperatur e of Apple por table computers , see Knowledge Base ar ticle 306 1 2 : “ Apple Notebooks: Operating T emperature ” . Y ou may also want to point out this article to the customer . Fan fails Check fan cable connection, and check cable for ...

  • Apple 13 INCH LATE 2006 - page 327

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 32 7 Battery won’t charge Remove an y connec ted peripherals . T r y known-good power outlet. T r y known-good power adapter and pow er cord. Note: Verify that po wer adapter connector glows amber or green. If the power adapter light is green, turn over the computer and pr ess the batter y bu ...

  • Apple 13 INCH LATE 2006 - page 328

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 32 8 Optical drive does not accept CD or DVD disc (mechanical failur e) V erify disc is not warped. V erify drive slot has no foreign object in channel. V erify disc is properly seated in the carrier . Replace optical drive. See Knowledge Base ar ticle 88288 “ Apple P or tables: Tips for inse ...

  • Apple 13 INCH LATE 2006 - page 329

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 329 Remove an y connec ted peripherals . T r y known-good power outlet. Remove battery , and remov e AC power . Pr ess Caps Lock key to see if light on key comes on. If it does, hold p ow er button down for six seconds to shut down the comput er and restar t. Reset PRAM (Pre ss the power button ...

  • Apple 13 INCH LATE 2006 - page 330

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 3 30 black or white MacBook is within the serial number range xx6 1 7xxxxxx - xx635xxxxxx, Apple will replace the heatsink under warran t y . Important: Do not disclose serial number ranges to customers. Order the follo wing par t for all MacBook computers exhibiting this behavior: 076-1 243 He ...

  • Apple 13 INCH LATE 2006 - page 331

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 3 3 1 Display Issue: When displaying a single color over the screen ar ea, the LCD panel shows one or mor e pixels that ar e not properly lit T o determine whether or not the display has an acceptable number of pixel anomalies , follow the steps below: Set the display image to one of the follow ...

  • Apple 13 INCH LATE 2006 - page 332

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 3 32 it is quite possible to hav e a low number of faulty transistors on an L CD. T herefore , a certain number of subpixel anomalies are c onsidered acceptable. Rejecting all but per fect L CD panels would signicantly increase the r etail price for products using L CD displays. These factor ...

  • Apple 13 INCH LATE 2006 - page 333

    MacBook (1 3-inch) Tr oubleshooting — Symptom Charts 3 33 left or right speaker . Play a sound to tell which s peaker is not responding and may need replacement. Based on results, replace either the left or right speaker . Replace logic board . No sound from speaker(s) Reset PRAM (Pre ss the power button, then hold down the Option-Command-P-R key ...

  • Apple 13 INCH LATE 2006 - page 334

    MacBook (1 3-inch) Tr oubleshooting — Block Diagram 3 34 Block Diagram ...

  • Apple 13 INCH LATE 2006 - page 335

    MacBook (1 3-inch) Tr oubleshooting — Block Diagram 3 3 5 Study the block diagram to understand which I/O ports have a direct connection to the outside world and which ports have an I/O interface controller between the system I/O mapper and the outside world. F or example, let us say you are tr oubleshooting an AirP or t connectivity symptom. Inp ...

  • Apple 13 INCH LATE 2006 - page 336

     Service Source © 2006, 2007 Apple Inc . All rights re ser ved. V iews MacBook (13-inch) ...

  • Apple 13 INCH LATE 2006 - page 337

    MacBook (1 3-inch) Views— 3 3 7 External and Internal V iews Fr ont: Keyboard and IR W indow ...

  • Apple 13 INCH LATE 2006 - page 338

    MacBook (1 3-inch) Views— 3 38 Back: Air V ents and Display Clutch Left Side: Ports Right Side: Slot Drive ...

  • Apple 13 INCH LATE 2006 - page 339

    MacBook (1 3-inch) Views— 3 39 Battery Bay: Memory Card Levers and Hard Drive Pull T ab Important: The following image shows the memory cards and hard drive installed in the battery bay with the L-shaped RAM door remov ed. Note the correct position of the memor y card lev ers. Some images pictured in this manual used a pre-production model, so th ...

  • Apple 13 INCH LATE 2006 - page 340

    MacBook (1 3-inch) Views— 340 ...

  • Apple 13 INCH LATE 2006 - page 341

    MacBook (1 3-inch) Views— 34 1 ...

  • Apple 13 INCH LATE 2006 - page 342

    MacBook (1 3-inch) Views— 342 ...

  • Apple 13 INCH LATE 2006 - page 343

    MacBook (1 3-inch) Views— 343 ...

  • Apple 13 INCH LATE 2006 - page 344

    MacBook (1 3-inch) Views— 344 ...

  • Apple 13 INCH LATE 2006 - page 345

    MacBook (1 3-inch) Views— 345 Screw Matrix T op Case Screw Locations Note: Screw lengths are appro ximate and cover the full length of the scr ew , including the scr ew head. Screw size, location, and par t number details are subject to change. T o o er a needed correction, click the Contact Us link on Ser vice Source Online . MacBook (1 3-inc ...

  • Apple 13 INCH LATE 2006 - page 346

    MacBook (1 3-inch) Views— 346 Display Module Scr ew Locations Note: Screw lengths are appro ximate and cover the full length of the scr ew , including the scr ew head. Screw size, location, and par t number details are subject to change. T o o er a needed correction, click the Contact Us link on Ser vice Source Online . MacBook (1 3-inch) View ...

  • Apple 13 INCH LATE 2006 - page 347

    MacBook (1 3-inch) Views— 347 Logic Board Scr ew Locations Note: Screw lengths are appro ximate and cover the full length of the scr ew , including the scr ew head. Screw size, location, and par t number details are subject to change. T o o er a needed correction, click the Contact Us link on Ser vice Source Online . MacBook (1 3-inch) Views? ...

  • Apple 13 INCH LATE 2006 - page 348

    MacBook (1 3-inch) Views— 348 LCD Panel Scr ew Locations Note: Screw lengths are appro ximate and cover the full length of the scr ew , including the scr ew head. Screw size, location, and par t number details are subject to change. T o o er a needed correction, click the Contact Us link on Ser vice Source Online . 2 2 2 4 1 1 3 3 3 3 5 5 3 2 ...

  • Apple 13 INCH LATE 2006 - page 349

    MacBook (1 3-inch) Views— 349 Scr ew Reference Chart, Part 1 of 3 MacBook (1 3-inch) Views— 290 Screw Chart 92 2-59 1 1 Phillips #0 0 m m 1 0 m m interchangable w/ 9 22-762 0? (except no n ylock coating) 92 2-59 1 6 Phillips #0 0 m m 1 0 m m fan (upper left corner), MLB, left clutch block 92 2-6443 Phillips #0 0 m m 1 0 m m Bluetooth-to-logic b ...

  • Apple 13 INCH LATE 2006 - page 350

    MacBook (1 3-inch) Views— 3 50 Scr ew Reference Chart, Part 2 of 3 MacBook (1 3-inch) Views— 29 1 Screw Chart 92 2-7 430 Torx T8 0 m m 1 0 m m hard drive assembly 92 2-7 43 1 Phillips #0 0 m m 1 0 m m optical drive assembly 92 2-7 582 Phillips #0 0 m m 1 0 m m Airport card, upper r t corner 92 2-7 583 Phillips #0 0 m m 1 0 m m heatsink, midfram ...

  • Apple 13 INCH LATE 2006 - page 351

    MacBook (1 3-inch) Views— 3 5 1 Scr ew Reference Chart, Part 3 of 3 92 2-5 9 1 0 Phillips #0 0 m m 1 0 m m Camera Board 92 2-8 1 3 3 Phillips #0 0 m m 1 0 m m Camera Bracket ...

  • Apple 13 INCH LATE 2006 - page 352

    MacBook (1 3-inch) Views— 3 52 Exploded V iews MacBook (13-inch)—Display Exploded V iew Display Rear Housing 922-7400 922-7597 Black LCD Panel 661-3959 Display Bezel 922-7776 922-7598 Black Bezel Scoop, Left 922-7777 922-7599 Black Bezel Scoop, Right 922-7778 922-7600 Black L VDS Cable with USB Line 922-7613 Shim at Bezel Scoop, Pkg. of 5 922-7 ...

  • Apple 13 INCH LATE 2006 - page 353

    MacBook (1 3-inch) Views— 3 53 MacBook (13-inch)—Main Exploded V iew T op Case with Keyboard 922-7754 922-7601 Black Optical Drive 661-3905 Combo 661-3906 Super Fan 922-7372 Logic Board (with Heatsink) 661-4218 1.83 GHz 661-4219 2 GHz 661-4220 2 GHz, Black Bluetooth Antenna 922-7367 Optical Drive Cable Kit 076-1224 AirPort Extreme Card 661-3890 ...

  • Apple 13 INCH LATE 2006 - page 354

    MacBook (1 3-inch) Views— 3 54 MacBook (13-inch Late 2006)—Display Exploded V iew Display Rear Housing 922-7898 922-7899 LCD Panel (Includes L VDS Cable) 661-421 1 Display Bezel 922-7776 922-8009 Black Bezel Scoop, Left 922-7777 922-7599 Black Bezel Scoop, Right 922-7778 922-7600 Black L VDS Cable with USB Line 922-7889 AUO/Chi Mei/LG 922-7890 ...

  • Apple 13 INCH LATE 2006 - page 355

    MacBook (1 3-inch) Views— 3 55 MacBook (13-inch Late 2006)—Main Exploded V iew T rackpad Cable 922-7991 AirPort Extreme Card 661-4058 Subwoofer with Right Speaker Cable 922-7371 Left Speaker 922-7370 Bluetooth-to-Logic Board Cable 922-7366 Hard Drive 661-4086 60 GB 661-4087 80 GB 661-4088 120 GB 661-4089 160 GB 661-4142 200 GB RAM Door 922-7895 ...

  • Apple 13 INCH LATE 2006 - page 356

    MacBook (1 3-inch) Views— 3 56 MacBook (13-inch Mid 2007)—Display Exploded V iew Display Rear Housing 922-7898 922-7899 Black LCD Panel (Includes L VDS Cable) 661-4398 Display Bezel 922-7776 922-8009 Black Bezel Scoop, Left 922-7777 922-7599 Black Bezel Scoop, Right 922-7778 922-7600 Black L VDS Cable with USB Line 922-7889 AUO/Chi Mei/LG 922-7 ...

  • Apple 13 INCH LATE 2006 - page 357

    MacBook (1 3-inch) Views— 3 57 MacBook (13-inch Mid 2007)—Main Exploded V iew AirPort Extreme Card 661-4058 Subwoofer with Right Speaker Cable 922-7371 Left Speaker 922-7370 Bluetooth-to-Logic Board Cable 922-7366 Hard Drive 661-4283 80 GB 661-4285 120 GB 661-4286 160 GB 661-4142 200 GB RAM Door 922-7381 Battery 661-4413 661-4414 Black Bottom C ...

Produzent Apple Kategorie Laptop

Dokumente, die wir vom Produzenten des Geräts Apple 13 INCH LATE 2006 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Apple
- Bedienungsanleitungen 13 INCH LATE 2006
- Produktkarten Apple
- Informationsbroschüren
- oder Energieetiketten Apple 13 INCH LATE 2006
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Apple 13 INCH LATE 2006.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Apple 13 INCH LATE 2006, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Apple 13 INCH LATE 2006. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Apple 13 INCH LATE 2006 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Apple 13 INCH LATE 2006, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Apple 13 INCH LATE 2006 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Apple 13 INCH LATE 2006 verständlich ist.

Eine gänzliche Bedienungsanleitung von Apple sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Apple 13 INCH LATE 2006 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Apple 13 INCH LATE 2006 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Apple 13 INCH LATE 2006, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Apple 13 INCH LATE 2006 - die uns die ersten Schritte während der Nutzung von Apple 13 INCH LATE 2006 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Apple 13 INCH LATE 2006 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Apple 13 INCH LATE 2006 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Apple 13 INCH LATE 2006?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Apple 13 INCH LATE 2006 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Apple 13 INCH LATE 2006 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)