Bedienungsanleitung Allied Telesis 86253-07

34 Seiten 0.2 mb
Download

Zur Seite of 34

Summary
  • Allied Telesis 86253-07 - page 1

    Simply connecting the world Patch Release Note Patch 86253-07 For Rapier Series Switches Intr oduction This patch rel ease note lists the issues addres sed and enhancements made in patch 86253-07 for Software Release 2.5.3 on existing models of Rapier series switches. Patch file details are listed in T able 1. This release note should be r ead in c ...

  • Allied Telesis 86253-07 - page 2

    2 Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Some of the issues addresse d in this Re lease Note include a level number . This number reflects the importance of the issue that has been r esolved. The levels are: Featur es in 86253-07 Patch 86253-06 was not released. Patch 86253-07 includes all issues reso lved ...

  • Allied Telesis 86253-07 - page 3

    Patch 86253-07 For Rapier Series Swit ches 3 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E A memory leak occurred if DNS r elay was configured, and the device kept receivi ng DNS Query packets. This issue has been resolved. PIM6 could not send unicast bootstrap messages to a new neighbour . This issue has been r esolved. If the SM ...

  • Allied Telesis 86253-07 - page 4

    4 Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E A filter entry was lost when the SET SWITCH L 3FIL TER ENTR Y command did not succeed. This issue has been r esolved. Link-local addr esses can only be unicas t addr esses. If a link-local address was added as an anycast addr ess, no error message was r eturned. Thi ...

  • Allied Telesis 86253-07 - page 5

    Patch 86253-07 For Rapier Series Swit ches 5 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E Entering “?” after a command at the CL I gives context-se nsitive Help about parameters valid for the command. O ccasionally , commands (for example, ENABLE IP MUL TICASTING) were executed when “?” was entered at the end of the comma ...

  • Allied Telesis 86253-07 - page 6

    6 Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Featur es in 86253-05 Patch file details are listed in T able 2: Patch 86253-05 includes all issues reso lved and e nhancem ents released in previous patch es for Software Release 2.5.3, an d the following enhancements: A buffer leak occurr ed when rapid STP was spe ...

  • Allied Telesis 86253-07 - page 7

    Patch 86253-07 For Rapier Series Swit ches 7 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E On A T -8800 series switches, stri ct QoS scheduling is now enforced for ports where egr ess rate limiting is applied. On Rapier i series switches, the same QoS setup is now applied to all of the appr opriate ports when setting up egress rat ...

  • Allied Telesis 86253-07 - page 8

    8 Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E When two devices ar e BSR candidates, and have the same pr eference set with the SET PIM BSRCANDIDA TE PREFERENCE command, the device with the higher IP addr ess was not elected as the candidate. This issue has been resolved. A Prune message sent to an old RP neighb ...

  • Allied Telesis 86253-07 - page 9

    Patch 86253-07 For Rapier Series Swit ches 9 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E The warning given when a QoS policy is active on a port operating at reduce d speed has been changed to reflect the pr oblem more accurately . The old message was: Warning (2087343): Port <Port num > is currently used in QoS policy < ...

  • Allied Telesis 86253-07 - page 10

    10 Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E When the device received a version 1 Query packet, it become a non-querier on that interface, even if it should have remained as the querier . This issue has been re solved. When the TYPE parameter was specified for the AD D SWITCH L3FIL TER command, the type was s ...

  • Allied Telesis 86253-07 - page 11

    Patch 86253-07 For Rapier Series Swit ches DELETE IGMPSNOOPING ROUTERADDRE SS 11 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E ADD IGMPSNOOPING ROUTERADDRESS Syntax ADD IGMPSNOOPING ROUTERADDRESS= ipaddr [, ... ] Description where: • ipaddr is a reserved IP multicas t addres s in dotted decimal notation. This command adds r eser ...

  • Allied Telesis 86253-07 - page 12

    12 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Description This command deletes r eserved IP multicast addre sses fr om the list of r outer multicast addresses. The IP addr ess specified must b e within the range 224.0.0.1 to 224.0.0.2 55. This comman d is only valid if the IGMP ...

  • Allied Telesis 86253-07 - page 13

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 13 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E The port counters were not incr ement ed: • ifInDiscard s •i f i n E r r o r s • ifOutDiscards •i f O u t E r r o r s This issue has been r esolved. The following SNMP MIB objects could not be set: ? ...

  • Allied Telesis 86253-07 - page 14

    14 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E •T h e Pr oposal f l a g i s n o t s e t i n a B P D U s e n t b y a d e s i g n a t e d p o r t o n c e t h e port has reached the forwarding state. Static ARP entries someti mes prev ented the firewal l from working correctly . ...

  • Allied Telesis 86253-07 - page 15

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 15 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E When static port security was enabled with the REL EARN parameter in the SET SWITCH POR T command, and a switch port was reset or unplugged, the MAC entries were r e moved (unlearned) from the forwar ding dat ...

  • Allied Telesis 86253-07 - page 16

    16 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E When using MVR on a Rapier 48 or Rapier 48 i , m ulticast packets we re not forwarded corr ectly between ports 1- 24 and 25-48. This issue has been res ol v ed . The switch filter was not operating corr ectly after a boot cycle. Thi ...

  • Allied Telesis 86253-07 - page 17

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 17 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E For example, to t urn off the Dif fie Hellman paddi ng, use the comman d: SET ENCO DHPADDING=OFF Also, the output of the SHOW ENCO command now contains a new line showing the setting for DHP ADDING. BGP was i ...

  • Allied Telesis 86253-07 - page 18

    18 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E If a configuration file had a long file name , the SHOW CONFIG command displayed the file name using the shortened DOS 8.3 format (where file names are 8 characters long, with extens ions of 3 characters). This issue has been resol ...

  • Allied Telesis 86253-07 - page 19

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 19 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E The MTU value for IPv6 PPP interfaces was always set to 1280 bytes. This MTU value is now correctly set to 1500 bytes, and 1492 bytes for PPP over Ethernet (PPPoE). OSPF sometimes chose r outes with an infini ...

  • Allied Telesis 86253-07 - page 20

    20 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E BGP sometimes chose routes with an infini te metric over routes with a finite metric when selecting the best local route. This issue has been resolved. The ipForwDatagrams SNMP MIB object was incremented when it should not have been ...

  • Allied Telesis 86253-07 - page 21

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 21 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E The switch was adding a router port for multic ast packets to destinations with an address in the range 224.0.0. x. Switch port entries ar e now only created for special r outer multicast addresses. If the DH ...

  • Allied Telesis 86253-07 - page 22

    22 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Incorrect debug information was r eturned when an ICMPv6 PacketT ooBig message was received. This issu e has been resolved. ISAKMP in aggressive mode did not establish a conne ction when the peer client sent 10 or mor e payloads. Th ...

  • Allied Telesis 86253-07 - page 23

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 23 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E An anycast address could not be assigned when the pr efix for the anycast address had pr eviously been assigned on that interface. This issue has been res ol v ed . The ADD FIREW ALL POLICY RULE and SET FIREW ...

  • Allied Telesis 86253-07 - page 24

    24 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E When the switch r eceived a generati on ID change message, it was not respondi ng by sending a PIM HELLO mess age. This is sue has been res ol v ed . BGP did not always send With dr aw n advertisements when a route went down. This i ...

  • Allied Telesis 86253-07 - page 25

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 25 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E Featur es in 86253-02 Patch file details are listed in T able 5: Patch 86253-02 includes the following enhancements and resolved issues: It is no w po s si bl e t o pre ve n t s pe ci f ie d p o rt s f rom a ...

  • Allied Telesis 86253-07 - page 26

    26 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E When adding a port to a VLAN, any STP ports that had been disabled in the default STP wer e re-enabled. This issue has been r esolved. When the DELETE DHCP RANGE command was executed, DHCP attempted to r eclaim the addr esses in tha ...

  • Allied Telesis 86253-07 - page 27

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 27 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E The IP multicast counter did not incre ment when IGMP , DVMRP and PIM packets were transmitted and r eceived. This issue has been resolved. The fir ewall denied str eaming data using W indows Media Player 9. ...

  • Allied Telesis 86253-07 - page 28

    28 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Enable and Disable ICMP Messages The Internet Control Message Protocol (ICMP) allows routers to send error and control messages to other r outers or hosts. It provides the communi cation between IP software on one system and IP soft ...

  • Allied Telesis 86253-07 - page 29

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 29 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E If ALL is specif ied, all confi gurable ICMP message r eplies are di sabled. If NETUNREACH is specif ied, all network unr eachable message repli es ar e disabled (RFC792 T ype 3 Code 0). If HOSTUNREACH is spe ...

  • Allied Telesis 86253-07 - page 30

    30 SHOW IGMPSNOOPING ROUT ERADDRESS Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E MLD Snooping Multicast Listener Discovery (MLD) snoo ping enables the switch to forward IPv6 multicast traf fic intelligently , inst ead of flooding it out all ports in the VLAN. W ith MLD snooping, the switch passively listens to M ...

  • Allied Telesis 86253-07 - page 31

    Patch 86253-07 For Rapier Series Swit ches SHOW IGMPSNOOPING ROUTERADDRESS 31 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E IGMP Snooping All-Gr oup Entry Because IGMP is an IP-based pr otocol, multicast gr oup membership for VLAN aware devices is on a per -VLAN basis. If at least one port in the VLAN is a member of a multicast gr ...

  • Allied Telesis 86253-07 - page 32

    32 SHOW IP IGMP Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E Modified Command SHOW IP IGMP Syntax SHOW IP IGMP [COUNTER] [INTERFACE= interface ] Description This command displays information about IGMP , and multicast group membership for each IP interface. This enhancement includes the line “ Disabled All-gro ...

  • Allied Telesis 86253-07 - page 33

    Patch 86253-07 For Rapier Series Sw itches DISABLE IP IGMP ALLG ROUP 33 Patch 86253-07 for Software R elease 2.5.3 C613-10382 -00 REV E New Commands This enhancement r equest introduces two new commands fr om enabling/ disabling all- group e ntries on switch ports. ENABLE IP IGMP ALLGROUP Syntax ENABLE IP IGMP ALLGROUP=[{ port-list |ALL}] where: ? ...

  • Allied Telesis 86253-07 - page 34

    34 DISABLE IP IGMP ALLGROUP Patch Release Note Patch 86253-07 for Software R elease 2.5.3 C613-10382-00 REV E A vailability Patches can be downloaded fr om the So ftware Updates ar ea of the Allied T elesyn web site at www .alliedtelesyn.co.nz/su pport/updates/patches.html . A licence or passwor d is not re quir ed to use a patch. ...

Produzent Allied Telesis Kategorie Speaker

Dokumente, die wir vom Produzenten des Geräts Allied Telesis 86253-07 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Allied Telesis
- Bedienungsanleitungen 86253-07
- Produktkarten Allied Telesis
- Informationsbroschüren
- oder Energieetiketten Allied Telesis 86253-07
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Allied Telesis 86253-07.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Allied Telesis 86253-07, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Allied Telesis 86253-07. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Allied Telesis 86253-07 ansehen.

Die komplette Bedienungsanleitung des Geräts Allied Telesis 86253-07, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Allied Telesis 86253-07 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Allied Telesis 86253-07 verständlich ist.

Eine gänzliche Bedienungsanleitung von Allied Telesis sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Allied Telesis 86253-07 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Allied Telesis 86253-07 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Allied Telesis 86253-07, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Allied Telesis 86253-07 - die uns die ersten Schritte während der Nutzung von Allied Telesis 86253-07 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Allied Telesis 86253-07 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Allied Telesis 86253-07 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Allied Telesis 86253-07?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Allied Telesis 86253-07 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Allied Telesis 86253-07 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)