Bedienungsanleitung Avaya 03-300686

156 Seiten 2.03 mb
Download

Zur Seite of 156

Summary
  • Avaya 03-300686 - page 1

    Installing and Connecting the MDF and Telephones 03-300686 Issue 3 Release 5.0 January 2008 ...

  • Avaya 03-300686 - page 2

    © 2008 A vaya Inc. All Right s Reserved. Notice While reasonable ef forts were made to ensure that the information in this document was complete and accurate at the time of printi ng, Avaya Inc. can assume no liability for any errors. Chan ges and corrections to the information in this document may be incorporated in futur e releases. For full sup ...

  • Avaya 03-300686 - page 3

    Issue 3 January 2008 3 Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 How to use this document ation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Downloading this book and updates from the Web . . . . . . . . . . . ...

  • Avaya 03-300686 - page 4

    Contents 4 Installing and Connec ting the MDF and Telephones Site locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 St ation circuit distribution from equipment room . . . . . . . . . . . . . . . . . 44 4-pair station circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 3-pair to 4-pair statio ...

  • Avaya 03-300686 - page 5

    Contents Issue 3 January 2008 5 Dual wiring of 2-wire and 4-wire endpoints . . . . . . . . . . . . . . . . . . . 87 Installing the attendant console . . . . . . . . . . . . . . . . . . . . . . . . . 87 Installing the 26B1 Selector Console . . . . . . . . . . . . . . . . . . . . . . 88 Connecting external alarm indicators and auxiliary power . . . . ...

  • Avaya 03-300686 - page 6

    Contents 6 Installing and Connec ting the MDF and Telephones Connecting cables to telephones and o ther end devices . . . . . . . . . . 122 1 152B Mid-S p an Power Distribution Unit s . . . . . . . . . . . . . . . . . . . . . . 123 Important 1152B PDU Safety Instruction s . . . . . . . . . . . . . . . . . . . . 124 Using the 1152B PDUs . . . . . . ...

  • Avaya 03-300686 - page 7

    Contents Issue 3 January 2008 7 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 47 Telephone console LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Attendant console LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Terminal alarm notification . . . . . . . . . . . . . . . ...

  • Avaya 03-300686 - page 8

    Contents 8 Installing and Connec ting the MDF and Telephones ...

  • Avaya 03-300686 - page 9

    Issue 3 January 2008 9 Chapter 1: Introduction This documentation, Installing and Connecting the MDF and T elephones provides procedures for inst alling Main Distribution Frames (MDF ) and telephones. The procedures explain how you connect media gateways to the MDF and ho w to connect the MDF to the public switched telephone network (PSTN). This do ...

  • Avaya 03-300686 - page 10

    Introduction 10 Installing and Conne cting the MDF a nd Telephones Connect the necessary telephone, trunking, and peripheral equipment using the information in Installing and wirin g telephones and trunks on page 69 and Installing a nd wiring telephone power supplie s on page 109. Complete the installatio n using information in the following sectio ...

  • Avaya 03-300686 - page 11

    Related resources Issue 3 January 2008 11 Sending us comment s Avaya welcomes your comments about this book. T o reach us by: ● Mail, send your comment s to: Ava y a I nc . Product Documenta tion Group Room B3-H13 1300 W . 120th A ve. Westminster , CO 80234 USA ● E-mail, send your comment s to: document@avaya.com ● Fax, send your comments to: ...

  • Avaya 03-300686 - page 12

    Introduction 12 Installing and Conne cting the MDF a nd Telephones ● Maintenance Commands for A vaya Communica tion Manager 5.0, Media Gateways and Servers, (03-300431). Provides information on how to use command interfaces, command syntax, and output f rom maintenance-related commands. ● Maintenance Alarms for A vaya Communication Manager 5.0, ...

  • Avaya 03-300686 - page 13

    Issue 3 January 2008 13 Chapter 2: Inst alling the main distribution frame If the equipment room does no t have one, you must build a main distribution frame (MDF) that connects the media gat eways to the building phone network and to the public switch ed telephone network (PSTN). The t asks include the following: ● Physical requirement s and lay ...

  • Avaya 03-300686 - page 14

    Installing the main distribution frame 14 Installing and Conne cting the MDF a nd Telephones Cable Slack Manager A Cable Slack Manager is 32 inches (81.3 ce ntimeters) wide. Slack managers are commonly used in installations co nsisting of media gateway stacks, such as the SCC1 Media Gat eways. Determine the quantity of slack managers by dividing th ...

  • Avaya 03-300686 - page 15

    Physical requirement s and layout Issue 3 January 2008 15 Sizing 4-p air station cables Use the scale of the floor plan to de termi ne the approximate length of the st ation cables required per the st andard SYSTIMAX wiring concepts. Sizing 25-p a ir and multip le 25-p air st ation cables Use the scale of the floor plan to de termi ne the approxima ...

  • Avaya 03-300686 - page 16

    Installing the main distribution frame 16 Installing and Conne cting the MDF a nd Telephones Main distribution frame cross-connect fields Each main distribution frame (M DF) cont ains a trunk/auxiliary field and a distribution field. The trunk/auxiliary field cont ai ns three cross-connect areas: ● The green field terminates the network inte rfac ...

  • Avaya 03-300686 - page 17

    Main distribution frame hardware installation Issue 3 January 2008 17 Main distribution frame hardware inst allation This section provides information on inst alling a main distribution frame (MDF) in an equipment room. It must be inst alled before connecting medi a gateways to it and before connecting it to the public switched telephone ne twork ( ...

  • Avaya 03-300686 - page 18

    Installing the main distribution frame 18 Installing and Conne cting the MDF a nd Telephones Figure 2: Example MDF connectio ns (G650 Media Gateway) Figure notes: 1. Rear of Media Gateway 2. Main Distribution Frame (MDF) 3. Port Distribution Field (Purple Field) 4. St ation Distribution Field (White Field) 5. T runk/Auxiliary Field 6. Purple Field ...

  • Avaya 03-300686 - page 19

    Main distribution frame place ment Issue 3 January 2008 19 Main distribution frame placement The preferred location of the MDF is d irectly behind the media gateways. Figure 3: T ypical 1 10A-type terminal blocks (G650 Media Gateway) shows a typical installation using 1 10A-type terminal blocks. Figure 3: T ypical 1 10A-type terminal blocks (G650 M ...

  • Avaya 03-300686 - page 20

    Installing the main distribution frame 20 Installing and Conne cting the MDF a nd Telephones Main distribution frame labels Figure 4: Label graphic symbols and nomenclature on page 20 shows th e graphic symbols used on labels for the media ga teways, cross-c onnections, information outlet s, and cables. The labels are color-coded to identify media ...

  • Avaya 03-300686 - page 21

    Mounting 110A- or 110P-type terminal block s on the wall Issue 3 January 2008 21 Mounting 1 10A- or 1 10P-type terminal blocks on the wall The 1 10A-type terminal blocks can be stacke d in almost any arrangement at any height or location on the wall. Figure 5: 1 10A-type termi nal blocks (300-p air) on page 22 shows one arrangement. The dist ance b ...

  • Avaya 03-300686 - page 22

    Installing the main distribution frame 22 Installing and Conne cting the MDF a nd Telephones 1 1. If installing anoth er distribution field terminal block, partiall y install the first screw for the terminal block, on the line, 7/8-inch (2.2 centime ter) to the right of the previous screw . Partially install the seco nd mounting screw 7-1 1 /16 inc ...

  • Avaya 03-300686 - page 23

    Mounting 110A- or 110P-type terminal block s on the wall Issue 3 January 2008 23 Figure 6: 1 10P-type terminal blocks (900-p air) Figure notes: 1. 4 feet ( 1.22 meters) 2. Horizont al Line 3. 7.68 inches (19.5 cen timeters) 4. 47.5 inches (120.6 ce ntimeters) 5. 5.31 inches (13.5 cen timeters) 6. 7/8-inch (2.22 centimeters) 7. 23 inches (58.4 centi ...

  • Avaya 03-300686 - page 24

    Installing the main distribution frame 24 Installing and Conne cting the MDF a nd Telephones Mounting 1 10P-type terminal blocks on a frame The 900-pair 1 10P-type terminal blocks and the associated patch cord troughs can also be mounted on a free-stan ding, floor-mounted 1 1 10A2 Apparatus Mounting Frame. See Figure 7: 1 1 10A2 and 1 1 10C1 appara ...

  • Avaya 03-300686 - page 25

    Installing Cable Slack Managers Issue 3 January 2008 25 Inst alling Cable Slack Managers Run excess cables on an upper cable ladder (if t he MDF connectors are on top) or route them through a cable slack manager that is placed next to the MDF . T o install cable slack ma nagers: 1. Place the Z1 13A Cable Slack Manager against the wall under the MDF ...

  • Avaya 03-300686 - page 26

    Installing the main distribution frame 26 Installing and Conne cting the MDF a nd Telephones Cable clamps are req uired in installations with cable slack managers. At the rear of the media gateways, install two cable clamps using th e screws provided. These clamp s hold the 25-p air input/output or MDF cables in place. Figure 8: Cable routing throu ...

  • Avaya 03-300686 - page 27

    Installing Cable Slack Managers Issue 3 January 2008 27 Figure 9: Cable routing through Cab le Slack Manager—example for SCC1 Media Gate way Figure notes: 1. T op of Media Gateways 2. Cable Clamp s 3. Cable Ti es (Optional) 4. Power Cord 5. Cable Slack Manager 6. Cable Slack Manager (Cover Removed) 7. Main Distribution Frame (MDF) 8. Route Cables ...

  • Avaya 03-300686 - page 28

    Installing the main distribution frame 28 Installing and Conne cting the MDF a nd Telephones ...

  • Avaya 03-300686 - page 29

    Issue 3 January 2008 29 Chapter 3: Inst alling the p atch p anel Inst alling p a tch p anels This chapter is for inst allations using a p atch panel ra ther than a main distribution frame for connections to the building phone ne twork and the public switched telephone network (PSTN). Patch panels are arrays of RJ45 jacks and as sociated B25A cables ...

  • Avaya 03-300686 - page 30

    Installing th e patch panel 30 Installing and Conne cting the MDF a nd Telephones Figure 10: T ypical RMC p atch panel inst allation Figure notes: 1. Circuit p ack amphenol connectors an d B25A cables 2. IP server interface adapter and green CA T5 cable 3. 24-port p atch p anels 4. 8-port p atch p anel 5. T o network cadlpat LJK 022502 1 2 3 3 4 5 ...

  • Avaya 03-300686 - page 31

    Cross-connectin g the media gateway to the patc h panels Issue 3 January 2008 31 Figure 1 1: Sample cross-connect field p atch p anel connections widfccf2 EWS 102798 4 11 0 1 9 41 3 2 2 21 1 2 0 51 4 2 3 31 2 2 1 61 5 2 4 91 8 71 6 2 5 81 7 Port Tie T runk Port MET Line 4 4 Port Tie T runk w/ E&M Signaling Port Data Line 8 Port Digital 8 Port B ...

  • Avaya 03-300686 - page 32

    Installing th e patch panel 32 Installing and Conne cting the MDF a nd Telephones ...

  • Avaya 03-300686 - page 33

    Issue 3 January 2008 33 Chapter 4: Media gateway connections to the MDF Once the main distribution frame (MDF) is in stalled and wired, you must conne ct the media gateways to the MDF . Run excess cables on an upper cable ladder (if t he MDF connectors are on top) or route them through a cable slack manager that is placed nex t to the MDF . For mor ...

  • Avaya 03-300686 - page 34

    Media gateway connections to t he MDF 34 Installing and Conne cting the MDF a nd Telephones Figure 12: Equipment room c abling labels The top blue/yellow building a nd floor labels are for cables connecting from the equipment room to a site/satellite location on another floor or in another building. The yellow label is for auxiliary circuits connec ...

  • Avaya 03-300686 - page 35

    Equipment room cabling labe ls Issue 3 January 2008 35 Figure 12: Equipmen t room cabling labels on page 34 details the label name and range of each label. T able 3: C able/connector/build i ng label ordering information provides label ordering information. Figure 13: Self-stick label on 25-pair cable connector shows the proper way to inst all a la ...

  • Avaya 03-300686 - page 36

    Media gateway connections to t he MDF 36 Installing and Conne cting the MDF a nd Telephones Cable routing guidelines Figure 14: Cable routing to top terminal blocks and Figure 15: Cable routing to bottom terminal blocks on page 37 show typical cable routing from the med ia gateway to the top and bottom of the MDF , respectively . Figure 14: Cable r ...

  • Avaya 03-300686 - page 37

    Cable routing guidelines Issue 3 January 2008 37 Figure 15: Cable ro uting to bottom terminal blocks Use these guidelines when routing cables from the media gateway to the MDF . Following these guidelines will maximize use of the cable sl ack managers and make future cabling additions and changes easier . ● Connect each port cable at the media ga ...

  • Avaya 03-300686 - page 38

    Media gateway connections to t he MDF 38 Installing and Conne cting the MDF a nd Telephones ● Coil the cable around the columns in the cable slack manager to store cable slack. The first run should always go across the full len gth of the 5 columns in the cable slack manager . ● Connect the cable to the a ssigned connecting/terminal block. ● ...

  • Avaya 03-300686 - page 39

    Installing connector cab les between auxiliary cab inet and MDF Issue 3 January 2008 39 Inst alling connector cables between auxiliary cabinet and MDF Auxiliary equipment that connect s to the MDF can be mounted inside t he auxiliary cabinet. The equipment connect s to an ED-1E1443-10 (Group 1) intraconnectio n panel mounted in the cabinet. This in ...

  • Avaya 03-300686 - page 40

    Media gateway connections to t he MDF 40 Installing and Conne cting the MDF a nd Telephones ...

  • Avaya 03-300686 - page 41

    Issue 3 January 2008 41 Chapter 5: MDF connections to st ations and the public switched telephone network Once the main distribution frame (MDF) is completed and the media gateways are connected to the MDF , you must connect the MDF to stations (telephones) and the public switched telephone network (PSTN). Y ou must also have a provision plan at th ...

  • Avaya 03-300686 - page 42

    MDF connections to stat ions and the public switched telephone network 42 Installing and Conne cting the MDF a nd Telephones S t ation cables For clarity a station cable is either a 25-p air cable, multiple 25-p air cable, or 4-pair D-inside wire (DIW) run from the equipment room, site/satellite location, or adapter to the informa tion outlets. The ...

  • Avaya 03-300686 - page 43

    Closets Issue 3 January 2008 43 4-pair st ation cable — Use this cable when 4-pair st ation cables are to be field-termin ated on the 1 10-type terminal blocks in the equipment room or sat ellite closet and the information outlets require push-on connections. Figure 17: Example of extending 4-p air st ation cables Closet s Closets are intermediat ...

  • Avaya 03-300686 - page 44

    MDF connections to stat ions and the public switched telephone network 44 Installing and Conne cting the MDF a nd Telephones Satellite locations using 1 10-type hardware Each terminal block has a 3-p air (white field) and a 4-pair (blue field) loca ted on the same terminal block. The 1 10A-type terminal block that can be used is t he 1 10AE1-75FT . ...

  • Avaya 03-300686 - page 45

    Station circuit distribution from equ ipment room Issue 3 January 2008 45 If most of the telephones/voice te rminals that r equire remote powering are within 250 feet (76.2 meters) of the equipment room, 4-p air station cir cuits are run from the equipment room to the information outlets . If this is not the case, or if the customer require s 2-poi ...

  • Avaya 03-300686 - page 46

    MDF connections to stat ions and the public switched telephone network 46 Installing and Conne cting the MDF a nd Telephones Figure 18: 4-p air circuit distribution and connectivity Figure notes: 1. Part of Main Distribution Frame (MDF) 2. 3-Pair Connecting Blocks 3. 4-Pair Connecting Blocks 4. Purple Field 5. Blue Field 6. Patch Cord or Cro ss-Con ...

  • Avaya 03-300686 - page 47

    Station circuit distribution from equ ipment room Issue 3 January 2008 47 Figure 19: 4-p air run to equipment room or satellite location Figure 20: 4-p air run to equipment room or satellite location Figure notes: 1. St ation Side of MDF or Satellite Location 2. 4-Pair Circuit 3. Blue Field 4. DIW St a tion Cable (D-In side Wire) 5. Information Out ...

  • Avaya 03-300686 - page 48

    MDF connections to stat ions and the public switched telephone network 48 Installing and Conne cting the MDF a nd Telephones Figure 21: 3-p air to 4-pair satelli te location connectivity Figure notes: 1. Part of MDF 2. 3-Pair Connecting Blocks 3. Purple Field 4. White Fi eld 5. Patch Cord or Cro ss-Connect Jumpers 6. T o Media Gateway (3-Pair Modul ...

  • Avaya 03-300686 - page 49

    Station circuit distribution from equ ipment room Issue 3 January 2008 49 Figure 22: 3-p air to 4-pair circuit dis tribution and connectivity Figure notes: 1. Part of Main Distribution Frame (MDF) 2. 3-Pair Connecting Blocks 3. Purple Field 4. Blue Field 5. Patch Cord or Cro ss-Connect Jumpers 6. T o Media Gateway (3-Pair Modularity) 7. B25A Cable ...

  • Avaya 03-300686 - page 50

    MDF connections to stat ions and the public switched telephone network 50 Installing and Conne cting the MDF a nd Telephones Connected cable st ation adapters S tation adapt ers are used to provide modular connectiv ity either directly to a telephone o r to an information outlet. See Figure 23: 258A and BR2580A Adapters and Figure 24: 3 56A Adapter ...

  • Avaya 03-300686 - page 51

    Connected cable sta tion adapters Issue 3 January 2008 51 Figure 24: 356A Ad apter Figure notes: 1. 356A Adapter 2. 4-Pair Modular Jacks (6 pins each, connected to 25-p air ribbon connector) T able 4: Adapter ordering information Description Comcode 258A Adapter 102605136 BR2580A Adapter 403384720 356A Adapter 104158829 400B Adapter 103848859 400B2 ...

  • Avaya 03-300686 - page 52

    MDF connections to stat ions and the public switched telephone network 52 Installing and Conne cting the MDF a nd Telephones Completing a provisioning plan A provisioning plan should be completed before an inst allation. The plan determines an appropriate available port circuit on the media gateway for each telephone, trunk, and peripheral connecti ...

  • Avaya 03-300686 - page 53

    Completing a provisioning plan Issue 3 January 2008 53 Figure 25: Port Assignment Record F orm ...

  • Avaya 03-300686 - page 54

    MDF connections to stat ions and the public switched telephone network 54 Installing and Conne cting the MDF a nd Telephones Inst alling sneak current a nd off premise protection Protection from hazardous volt ages and currents is required for all off-p remis es (out of building) trunks, lines, and terminal in stallations. Prot e ction for incoming ...

  • Avaya 03-300686 - page 55

    Installing sneak curren t and off premise prot ection Issue 3 January 2008 55 Figure 26: Model 507B sneak fuse p anel Connector cables (B25A male to female) connect t he network interface to the sneak fuse panel. Also, 157B connecting blocks equipped with SCP- 1 10 protectors can be used for sneak current protection. Figure notes: 1. 507B sneak cur ...

  • Avaya 03-300686 - page 56

    MDF connections to stat ions and the public switched telephone network 56 Installing and Conne cting the MDF a nd Telephones The 507B includes 52 sneak fuses and two cab les and can be ordered using PEC code 63210. Use the SCP-1 10 protectors with 1 10-type hardware and on the 507B sneak fu se panel. The SCP-1 10 Protectors can be ordered separatel ...

  • Avaya 03-300686 - page 57

    Installing sneak curren t and off premise prot ection Issue 3 January 2008 57 Inst alling sneak fuse p anels For general information, see Installing sneak current and of f premise protection on p age 54. Figure 26: Model 507B sneak fuse panel on page 55, or equivalent, is recommended for sneak current protection. The p anel contains two 25-p air co ...

  • Avaya 03-300686 - page 58

    MDF connections to stat ions and the public switched telephone network 58 Installing and Conne cting the MDF a nd Telephones Inst alling the coupled bonding conductor The coupled bonding conductor (CBC) provides a p a th to ground for transient energy (for instance, lightning) by virtue o f mutual inductance between it self and exposed telcom cable ...

  • Avaya 03-300686 - page 59

    Installing the coupled bonding conductor Issue 3 January 2008 59 Figure 27: T ypical power and ground for a DC power c abinet Note: Note: For a high-rise building, connect the CBC to an approved building ground on each floor . Note: Note: Below is general information for inst alling the CBC in all installations having exposed facilities. Figure not ...

  • Avaya 03-300686 - page 60

    MDF connections to stat ions and the public switched telephone network 60 Installing and Conne cting the MDF a nd Telephones T o provide the coupled bonding protection : 1. Cut a 10 A WG (#25) (2.5 mm 2 ) wire lon g enough to reach from the equipment roo m single-point ground block (or DC power Ground Discharge Bar) to the MDF CBC block. See Figure ...

  • Avaya 03-300686 - page 61

    Installing the coupled bonding conductor Issue 3 January 2008 61 Figure 28: Coupled Bonding Conductor Figure notes: 1. 25-Pair T ip & Ring Cables to Media Gateways 2. Coupled Bonding Co nductor (CBC) T erminal Block 3. Tie W raps 4. Cable Shield or Six Sp are Pairs 5. Ground on Carbon Block Protector or Equivalent 6. T runk Cable to Network Int ...

  • Avaya 03-300686 - page 62

    MDF connections to stat ions and the public switched telephone network 62 Installing and Conne cting the MDF a nd Telephones Inst alling and administering the p atch cord/jumper Before starting the patch cord inst allation, obtai n a copy of the Port Assignment Record forms from the customer or marketing represent ative. See Figure 25: Port Assignm ...

  • Avaya 03-300686 - page 63

    Installing and administering the patch cord/jumper Issue 3 January 2008 63 Figure 29: Example 3-p air labeling to information outlet Figure notes: 1. Equipment Room 2. Satellite Location 3. Work L ocation 4. White Row on 1 10 T erminal Block 5. Purple Row on 1 10 T erminal Block 6. Blue Row on 1 10 T erminal Block 7. Central Locatio n for T erminal ...

  • Avaya 03-300686 - page 64

    MDF connections to stat ions and the public switched telephone network 64 Installing and Conne cting the MDF a nd Telephones Figure 30: Example 4-p air labeling to information outlet Labeling exp ansion control carrier cable (MCC1 Media Gateway only) T o label the exp ansion control carrier cable: 1. Place the appro priate AUX connector label on th ...

  • Avaya 03-300686 - page 65

    Installing and administering the patch cord/jumper Issue 3 January 2008 65 Connecting exp ansion control carrier output s cable (MCC1 Media Gateway only) T o connect the exp ansion control carrier output s cable: 1. Plug the connector cable in the AUX connector on the rear of the exp ansion control carrier . 2. Route the connector cable through the ...

  • Avaya 03-300686 - page 66

    MDF connections to stat ions and the public switched telephone network 66 Installing and Conne cting the MDF a nd Telephones Figure 31: Connect trunk p airs using concentrator cables Figure notes: 1. T runk/Auxiliary Field 2. T o Expansion Co ntrol Carrier AUX Connector (MCC1 Media Ga teway only) 3. Concentrator Cable (WP90929, List 1) 4. Concentra ...

  • Avaya 03-300686 - page 67

    Installing and administering the patch cord/jumper Issue 3 January 2008 67 Connecting trunk p airs to media gateway using jumper wires to est ablish 3-p air modularity Figure 32: 3-pair modularity for trunk pairs f or 1-pair trunks on p age 67 and Figure 33: 3 -pair modularity for trunk pair s for 3-pair T ie trunks on pag e 68 show trunk pair s co ...

  • Avaya 03-300686 - page 68

    MDF connections to stat ions and the public switched telephone network 68 Installing and Conne cting the MDF a nd Telephones Figure 33: 3-p air modularity for trunk pa irs for 3-p air Tie trunks Figure notes: 1. Green Field 2. 1-Pair Jumpers 3. Pairs 4. Purple Field 123456789 1 0 1 1 1 2 123456789 1 0 1 1 1 2 123456789 1 0 1 1 1 2 17 16 15 14 13 18 ...

  • Avaya 03-300686 - page 69

    Issue 3 January 2008 69 Chapter 6: Inst alling an d wiring telephones and trunks The wiring procedures are the same fo r most Avaya telephones and other equipment. This task list provides wiring examples of similar insta llation procedures. These are examples only; actual wiring procedures may vary at each site. After inst alling the equipment, the ...

  • Avaya 03-300686 - page 70

    Installing and wiring telephones and t runks 70 Installing and Conne cting the MDF a nd Telephones ● Connecting external alarm i ndicators and auxiliary power on page 88 ● Installing of f-premises station wiring on page 9 0 ● Off-premises or out-o f-building stations on page 91 ● Off-premises connections on page 91 ● Emergency transfer un ...

  • Avaya 03-300686 - page 71

    Connecting teleph ones Issue 3 January 2008 71 2410 Digital 2420 IP/Digital 2520B Explosive Atmosphere Analog 3127 Av aya Soundstation/SoundPoint S peakerphones: 3127-A TR, -STD, -EXP , -APE, -APX, -MIC, -PMI Analog 3127 Av aya Soundstation/SoundPoint S peakerphones: 3127-DCP , -DCS, -DCE, -DPE, -DPX, -DDP , -DDX, -MIC, -PMI Digital 3410 Wireless 3 ...

  • Avaya 03-300686 - page 72

    Installing and wiring telephones and t runks 72 Installing and Conne cting the MDF a nd Telephones 606A Av aya CallMaster VI ACD Console Digital Softphones: Netmeeting H.323 IP Sof tphone CentreV u IP Agent Softconsole Internet Protocol (IP) T able 7: Connect able telephone and consoles (continu ed) T elephone and console models T ype 3 of 3 ...

  • Avaya 03-300686 - page 73

    Connecting teleph ones Issue 3 January 2008 73 Connecting a typical telephone The 302D Enhanced Attendant Console is us ed to describe a telephone connection typically used with the 84xx (4-wire) telephones. The 302D does not require auxiliary power un less it has a 26C1 DXS console or V acuum Fluorescent Display . The 302D attendant console always ...

  • Avaya 03-300686 - page 74

    Installing and wiring telephones and t runks 74 Installing and Conne cting the MDF a nd Telephones Figure 34: 302D to 4-wire DCP wiring Connecting adjunct power The 400B2 adapter is convenient for connecting local -48 VDC power to a modular plug. See Figure 35: 400B2 Adapter connecting to a modular plug on page 75. Each port network can provide pow ...

  • Avaya 03-300686 - page 75

    Connecting teleph ones Issue 3 January 2008 75 Figure 35: 400B2 Adapter connecting t o a modular plug Connecting an analog st ation or 2-wire digital st ation This example is typical of the 2-wire digit al st ations (2420, 64xx, 302D), 2-wire analog st ations (2500), analog central of fice (CO) trunks, direct inward dial (DID) trunks, and external ...

  • Avaya 03-300686 - page 76

    Installing and wiring telephones and t runks 76 Installing and Conne cting the MDF a nd Telephones Figure 36: 2500-type analog telephone wiring Analog tie trunk example This example shows how to connect analog ti e trunk wiring from on e IP Connect or Multi-Connect configuration to ano ther one or any other A vaya configuration. 1. Set the option s ...

  • Avaya 03-300686 - page 77

    Connecting teleph ones Issue 3 January 2008 77 4. Figure 37: Analog T ie T runk wiring on page 77 shows a media gateway tie trunk connected to another media gateway tie trun k. Names of the tie trunk leads must be d etermined from the manufacturer or supplier of the external trun k circuit. 5. Administer on the T runk Group screen on Avaya Site Adm ...

  • Avaya 03-300686 - page 78

    Installing and wiring telephones and t runks 78 Installing and Conne cting the MDF a nd Telephones Figure 38: Digit al Tie T runk wiring DS1 tie trunk example Digital Sign al Level 1 (DS1) tie trunks provide a 1.544 Mbp s (T1) or 2.048 Mbps (E1) digital dat a service between two collocated configurations or betwee n the configuration and a data net ...

  • Avaya 03-300686 - page 79

    Connecting teleph ones Issue 3 January 2008 79 DS1 interface trunks using T1 channel service unit The T1 channel service unit (CSU) interfaces the DS1 interface trunks with the 1.544 megabit s per second digital facility . Connect the DS1 interface trunk to a T 1 CSU. See Figure 39: T ypical connections to channel service unit on page 79. Note: Not ...

  • Avaya 03-300686 - page 80

    Installing and wiring telephones and t runks 80 Installing and Conne cting the MDF a nd Telephones T able 9: DS1 cables Connector cable Description and usage C6C connector cable 50-feet (15 meters) shie lded cable equipped with a 50-pin male connector on one end and a 15-pin ma le connector on the other end. Use this cable to connect a DS1 tie tru ...

  • Avaya 03-300686 - page 81

    Auxiliary connector ou tputs (MCC 1 and SCC1 Media Gateway s only) Issue 3 January 2008 81 Auxiliary connector output s (MCC1 and SCC1 Media Gateways only) Connect a 25-p air cable from the AUX connect or on the back of the expa nsion control carrier to a connecting block on th e trunk/auxiliary field. T able 1 1: Auxiliary lead ap pearances at AUX ...

  • Avaya 03-300686 - page 82

    Installing and wiring telephones and t runks 82 Installing and Conne cting the MDF a nd Telephones R-O O-R 32 7G R D R-G G-R 33 8 Not Connected R-BR BR-R 34 9 Not Connected R-S S-R 35 10 Not Connected BK-BL BL-BK 36 11 -48 GND Emergency T r ansfer Rela y Power BK-O O-BK 37 12 -48 GND BK-G G-BK 38 13 -48 GND BK-BR BR-BK 39 14 -48 GND BK-S S-BK 40 15 ...

  • Avaya 03-300686 - page 83

    Auxiliary connector ou tputs (MCC 1 and SCC1 Media Gateway s only) Issue 3 January 2008 83 T able 12: S tation pinout chart provides the st ation printout chart. V- B R BR-V 49 24 Not Connected V- S S-V 50 25 INADS Ti p INADS Ring *. Color designation is the main wire color and the col or of the stripe on the wire. The following wire colors apply: ...

  • Avaya 03-300686 - page 84

    Installing and wiring telephones and t runks 84 Installing and Conne cting the MDF a nd Telephones Three-p air and four-p air modularity Figure 40: 3-pair and 4-pair modularity o n page 84 is from the port circuit p ack to the voice or data terminal. Most terminals connect to an information outlet (modular jack) inst alled at the work location. Mak ...

  • Avaya 03-300686 - page 85

    Adjunct power connection locations Issue 3 January 2008 85 Adjunct power connection locations Figure 41: Example adjunct power conne ctions on page 85 shows typical connection locations for adjunct power . Adjunct power for station equipment may be supplied f rom the equipment room, satellite location, or the wo rk location. For this figure, the fo ...

  • Avaya 03-300686 - page 86

    Installing and wiring telephones and t runks 86 Installing and Conne cting the MDF a nd Telephones Attendant console example Perform these t asks to install an attendant console ● Installing the atten dant console on page 87 ● Installing the 26B1 Selecto r Console on page 88 Attendant console cabling dist ances, local and phantom power A consol ...

  • Avaya 03-300686 - page 87

    Attendant cons ole example Issue 3 January 2008 87 An attendant console can also der ive auxiliary power from: ● Individual 1 151B1 or 1 151B2 power supply ● 258A-type adapters ● Bulk power supplies such as the 1 145B2 A console’ s maximum distance from it s auxiliary power source is: ● 800 feet (244 meters) for a 302A1 ● 350 feet (107 ...

  • Avaya 03-300686 - page 88

    Installing and wiring telephones and t runks 88 Installing and Conne cting the MDF a nd Telephones Inst alling the 26B1 Selector Console T o install the 26B1 Selector Console: 1. Connect the supplied 3-foot (1 meter) D8AC cable to the mod ular jack on the bottom of the 26B1 Selector Console. 2. Route the cable to the attendant console and connect t ...

  • Avaya 03-300686 - page 89

    Connecting extern al alarm indicators and auxiliary powe r Issue 3 January 2008 89 Figure 43: Sample Issue 1 IPSI-2 a larm cable connectivity T o connect the external alarm indicators and the auxiliary power: 1. Connect 1 major (Brown-White and White-Brown) and 1 minor (Orange-White and White-Orange) alarm input p air to the trunk/auxiliary field f ...

  • Avaya 03-300686 - page 90

    Installing and wiring telephones and t runks 90 Installing and Conne cting the MDF a nd Telephones 4. Connect emerge ncy transfer power (Blue-White and White-Blue)) as shown in T able 14: Alarm Inputs at TN2312BP Adapter DB9 Alarm Connector . Inst alling off-premises st ation wiring The local telephone comp any provides cabling ou t side the buildi ...

  • Avaya 03-300686 - page 91

    Off-premises or out-of- building stations Issue 3 January 2008 91 3. Connect an A25D ca ble between the sneak fu se p anel and the terminal block connector associated with the green row in the pre vious step. 4. Inst all a green label on the termina l block to identify the remote location. 5. Administer per the Admin istrator Guide for A vaya Commu ...

  • Avaya 03-300686 - page 92

    Installing and wiring telephones and t runks 92 Installing and Conne cting the MDF a nd Telephones Figure 44: Connections for 1 to 8 out-o f-building analog telephones Figure notes: 1. Locally Engineered Cables and Equipment 2. Out-of-Building W i ring 3. 25-Pair Connect or 4. Multi-Pair Protector Units (Primary Protectors with Heat Coils or Eq uiv ...

  • Avaya 03-300686 - page 93

    Off-premises co nnections Issue 3 January 2008 93 Figure 45: Connections to 24 out-of- building telephones Off-premises protection requirement s Both building entrances require carbon b lock or equivalent protection and sneak current protection. Protection can be provided by: ● a 4-type protector , which is equipped with a heat coil ● a 3-type ...

  • Avaya 03-300686 - page 94

    Installing and wiring telephones and t runks 94 Installing and Conne cting the MDF a nd Telephones The 4-type protector is the prefe rred device. For installations not usin g primary protection, 4-type protectors should always be used. Wh en the 3-type protector is already installe d, a separate sneak current pro tector is required. The multi-pair ...

  • Avaya 03-300686 - page 95

    Off-premises co nnections Issue 3 January 2008 95 The 4C3S-75 may be used only with TN 754B Dig ital Line circuit p acks. T able 1 6: Digital V oice Circuit Protectors list s the approved protectors. When possible, all new and reused wiring insta llations sho uld use blocks that accept the standard 5-pin p lug-in 4C3S-75 protector . However , there ...

  • Avaya 03-300686 - page 96

    Installing and wiring telephones and t runks 96 Installing and Conne cting the MDF a nd Telephones See Figure 41: Example adjunct power connections on page 85 and Figure 46: Connections at trunk/auxiliary field on page 96. Figure 46: Connections a t trunk/auxiliary field Emergency transfer unit s and associated telephones An 808A Emergency T ransfe ...

  • Avaya 03-300686 - page 97

    808A Emergency Transfer Panel and te lephone installation examples Issue 3 January 2008 97 Should power be restored to the relays while a call connected through the 808A is in prog ress, the 808A maintains th e connection until the user goes on-hook. Each 808A can ha ndle up to five CO trunks. 808A Emergency T ransfer Panel and telephone inst allat ...

  • Avaya 03-300686 - page 98

    Installing and wiring telephones and t runks 98 Installing and Conne cting the MDF a nd Telephones Figure 47: 808A Emergency T ransfer Panel Figure notes: 1. 808A Emergency T ransfer Pane l 2. Circuit Start Selection Switches 3. T runk Identification Label 4. 25-Pair Male Connector 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 12 EMERGENCY TRANSFER PA N E L CIRCU ...

  • Avaya 03-300686 - page 99

    808A Emergency Transfer Panel and te lephone installation examples Issue 3 January 2008 99 Figure 48: 808A Emergency T ransfer Panel mounting Inst alling the 808A Emergency T ransfer Panel Note: Note: The 808A must be inst alled in a location that can be accessed only by authorized personnel. The location mu st meet sta ndard environment al c onsid ...

  • Avaya 03-300686 - page 100

    Installing and wiring telephones and t runks 100 Installing and Connect ing the MDF and Telephones 4. Connect a 25-p air cable between the ma le RJ21 25-pair connector on the Emergency T ransfer Panel and the yellow field of the MDF . T able 18: Pin assignments for 25-p air connector on page 101 shows the pinouts. 5. Make cross-connections for each ...

  • Avaya 03-300686 - page 101

    808A Emergency Transfer Panel and te lephone installation examples Issue 3 January 2008 101 . T able 17: T runk/test switches Switch number Circuit number 11 2 1 32 4 2 53 6 3 74 8 4 95 10 5 1 1 Not Used 12 Te s t S w i t c h T able 18: Pin assignment s for 25-pair connector 26 W-BL TTC1 T ip- PBX Tr u n k C i r c u i t 1 1 BL-W RTC 1 Ring- PBX Tr ...

  • Avaya 03-300686 - page 102

    Installing and wiring telephones and t runks 102 Installing and Connect ing the MDF and Telephones 32 R-O TLC2 T ip- PBX Line Port 2 7 O-R RLC2 Ring- PBX Line Port 2 33 R-G TST2 T ip-Emergency T erminal 2 8 G-R RST2 Ring-Emergency T erminal 2 34 R-BR TTC3 T ip- PBX Tr u n k C i r c u i t 3 9 BR-R RTC 3 Ring- PBX Tr u n k C i r c u i t 3 35 R-S TTK3 ...

  • Avaya 03-300686 - page 103

    808A Emergency Transfer Panel and te lephone installation examples Issue 3 January 2008 103 Figure 49: Connections for telephone used for emergency transfer 47 V -O NC2 Normally Closed 2 Contact 22 O-V NC1 Normally Closed 1 Cont act 48 V -G COM2 Common 2 Relay Contact 23 G-V NO2 Normally Open 2 Contact 49 V -BR 24 BR-V 50 V -S GRD Ground from Au x ...

  • Avaya 03-300686 - page 104

    Installing and wiring telephones and t runks 104 Installing and Connect ing the MDF and Telephones Figure 50: Connections for telephone used for emergency transfer and as normal extension Inst alling telephones used only for emergency transfer (trunk/auxiliary field) T o install telephones used only for emergency transfer: 1. Connect a p air of wir ...

  • Avaya 03-300686 - page 105

    808A Emergency Transfer Panel and te lephone installation examples Issue 3 January 2008 105 4. Connect ST leads on the ye llow emergency trans fer row/connecting block for each emergency transfer telephone to the assign ed terminal in the blue or white station distribution field. The ST terminal leads should be terminated on the following p airs: 1 ...

  • Avaya 03-300686 - page 106

    Installing and wiring telephones and t runks 106 Installing and Connect ing the MDF and Telephones Inst alling external ringing Connections for external ringing are at an info rmation out let. The media gateway sid e of the MDF is connected to a TN2183 (or equivalent) An alog Line circuit p ack. The circuitry and power source for the device are pro ...

  • Avaya 03-300686 - page 107

    Installing the queue warning indicator Issue 3 January 2008 107 Inst alling the qu eue warning indicator The connections for the queu e warning indicator are the sa me as external ringing. An AC indicator (lamp) such as a 21C49 can be used in a uniform call distribution/direct depa rtmental calling (UCD/ DDC ) queue. The lamp is connected to an inf ...

  • Avaya 03-300686 - page 108

    Installing and wiring telephones and t runks 108 Installing and Connect ing the MDF and Telephones ...

  • Avaya 03-300686 - page 109

    Issue 3 January 2008 109 Chapter 7: Inst alling and wiring telephone power supplies This section provides information and wiring exam ples of installation pro cedures for various telephone and console power supp lies. These are examples only an d actual wiring procedures may vary at each site. Note: Note: See Adding New Hardwa re for Avaya Serve rs ...

  • Avaya 03-300686 - page 110

    Installing and wiring telephone power supplies 110 Installing and Connect ing the MDF and Telephones 4. Installing the batte ry mounting/wiring on page 1 15 5. Installing the exp anded power distribution unit on p age 1 15 6. Powering up and testing the power supply on page 1 16 7. Wiring the 1 146B2 Powe r Distribution Unit on page 1 17 8. Resetti ...

  • Avaya 03-300686 - page 111

    1145B2 power supply Issue 3 January 2008 111 ● Power down the power unit (see label on power unit on how to do this) and refer servicing under the following conditions: ● If liquid has been spilled in to any of the product s ● If any of the product s have been exposed to water ● If any of the product s do not operate normally ● If any of ...

  • Avaya 03-300686 - page 112

    Installing and wiring telephone power supplies 112 Installing and Connect ing the MDF and Telephones Figure 52: 1 145B2/1 146B2 mounting arrangement Figure notes: 1. W all Mounting Plate 2. Battery (1 149B Shown) 3. 1 146B2 Power Distributio n Unit 4. 1 145B2 Power Unit 5. Power Cable 6. Nonswitched Out let (120 V AC, 20 amp or 230 V AC, 15 amp) 7. ...

  • Avaya 03-300686 - page 113

    1145B2 power supply Issue 3 January 2008 113 Figure 53: Exp anded power distribution unit Figure notes: 1. W all Mounting Plate 2. Battery (1 149B shown) 3. Second 1 146B2 Power Distribution Unit 4. “T” Cable (H600-347-G7) 5. First 1 146B2 Power Distribution Un it 6. 1 145B2 Power Unit 7. Nonswitched Outl et (120 V AC, 20 amp or 230 V AC, 15 am ...

  • Avaya 03-300686 - page 114

    Installing and wiring telephone power supplies 114 Installing and Connect ing the MDF and Telephones Inst alling the wall-mounting plates The top plate is used for mountin g the back-up battery . The bottom plate is used to mount the power supply and distributio n units. The pl ate s can be rack-mounted using st andard rack-mounting brackets. See F ...

  • Avaya 03-300686 - page 115

    1145B2 power supply Issue 3 January 2008 115 Inst alling the battery mounting/wiring Three types of back-up batteries are used. See T able 19: Ba ck-up battery rating on p age 1 15 for the battery type and rating. T o install the battery mounting and wiring: 1. Insert two #10-32 x 1/2 -inch shoulder screws into the top de signated battery holes on ...

  • Avaya 03-300686 - page 116

    Installing and wiring telephone power supplies 116 Installing and Connect ing the MDF and Telephones See Figure 53: Expanded power distribution unit on p age 1 13 while inst alling the power distribution unit. T o insta ll the expanded po wer distribution unit: 1. Set the sp acer bracket onto the mounting pl ate and secure with the #8-32 x 1/2-inch ...

  • Avaya 03-300686 - page 117

    1145B2 power supply Issue 3 January 2008 117 2. Plug the cord into the outlet. This p owers up the power supply . 3. Check AC operation of the 1 145B2 Power Supply by monitoring the LEDs: PA S S : Green and yellow LEDs at the front of the unit should be lit togethe r . See T able 20: Power supply LEDs on page 1 16. Afte r the battery reaches full c ...

  • Avaya 03-300686 - page 118

    Installing and wiring telephone power supplies 118 Installing and Connect ing the MDF and Telephones Figure 54: T ypical wirin g to a telephone Resetting LEDs on pow er distribution unit A red LED next to any o f the 32 power output co nnectors indicates a short circuit in the buildin g wiring or the terminal equipment. T o reset the LED: 1. Discon ...

  • Avaya 03-300686 - page 119

    1152A1 Mid-Span Powe r Dis tribution Unit Issue 3 January 2008 119 1 152A1 Mid-Sp an Power Distribution Unit The 1 152A1 Mid-S pan Power Distribution Unit (PDU) is an Ethernet p ower supply that provides power to up to 24 46xx-series IP telephones or wi reless LAN (WLAN) access points. This unit is used with a 10/100BaseTx standard Ethernet network ...

  • Avaya 03-300686 - page 120

    Installing and wiring telephone power supplies 120 Installing and Connect ing the MDF and Telephones ● Do not overload wall o utlets and extension cord s as this can result in the risk of line or electric shock. ● Disconnect the cords on this product and refer servicing to qualified service p ersonnel under the following conditions: ● If the ...

  • Avaya 03-300686 - page 121

    1152A1 Mid-Span Powe r Dis tribution Unit Issue 3 January 2008 121 T o connect the 1 152A1 Power Distribution Unit: 1. Plug a powe r cord into the power socket on the re ar of the 1 152A1 Power Distribution Unit. 2. Plug the other en d of the power cord into the power receptacle. The 1 152A1 PDU powers up, and the internal fans begin operating. The ...

  • Avaya 03-300686 - page 122

    Installing and wiring telephone power supplies 122 Installing and Connect ing the MDF and Telephones Connecting cables to teleph ones and other end devices The 1 152A1 PDU contains line-sensing capabilities that enable it to send power only to end devices designed to receive power from the LAN. These end devices, termed Power over LAN Enabled, rece ...

  • Avaya 03-300686 - page 123

    1152B Mid-Span Po wer Distribution Units Issue 3 January 2008 123 T o connect telephones and other end devices to the 1 152A1 PDU: 1. Connect an Etherne t cable to the telephone usi ng an external splitter or dire ctly (if the device is Power over LAN Enabled). 2. Connect the oppo site end of the same cable to the RJ45 wall outlet. 3. On the front ...

  • Avaya 03-300686 - page 124

    Installing and wiring telephone power supplies 124 Installing and Connect ing the MDF and Telephones The 1 152B PDU complies with the Underwriters Laboratories Inc. (UL) st andard UL 60950-1, 1 st Edition. Import ant 1 152B PDU Safety Instructions Please read the following help ful tips. Retain these tip s for later use. When using this switch, the ...

  • Avaya 03-300686 - page 125

    1152B Mid-Span Po wer Distribution Units Issue 3 January 2008 125 - Dropped or th e housing has been damaged - Exhibit s a distinct change in performance - Operates abn ormally when following the operating instructions Using the 1 152B PDUs The 1 152B PDUs are used to power the 46xx series and 96xx series of IP te lephones in addition to providing ...

  • Avaya 03-300686 - page 126

    Installing and wiring telephone power supplies 126 Installing and Connect ing the MDF and Telephones Figure 57: Connecting tele phones and other end devices to the 1 152B PDU For Data-I n ports connect th e Ethernet cable leading from the Ethernet Switch/Hub to the Dat a port. For Data & Power Out po rts connect the Ethe rnet cable leading to t ...

  • Avaya 03-300686 - page 127

    1152B Mid-Span Po wer Distribution Units Issue 3 January 2008 127 Figure 58: Connecting an IP telephone with an external split ter Before connecting teleph ones or other end devices to the 1 152B PDU, determine if the device: ● Is Power over LAN Enabled or not. If not, you may safely connect the telephone; h owever , the port supplies no power an ...

  • Avaya 03-300686 - page 128

    Installing and wiring telephone power supplies 128 Installing and Connect ing the MDF and Telephones C360 converged st ackable switches The Ava ya C360 series of converged st ackable switches include four main product s: The C360 converged stackable switches comply with the Underwriters Laboratories Inc. (UL) standard UL 60950. For safety instructi ...

  • Avaya 03-300686 - page 129

    C360 converged stac kable switches Issue 3 January 2008 129 ● Do not allow anything to rest on the power cord. Do not locate this product where the cor d will be abused by persons walking on it. ● Do not overload wall o utlets and extension cord s as this can result in the risk of line or electric shock. ● Disconnect the cords on this product ...

  • Avaya 03-300686 - page 130

    Installing and wiring telephone power supplies 130 Installing and Connect ing the MDF and Telephones Connecting the C360 st ackable switches Powering up—AC input T o connect the AC input: 1. Insert the power cord into the power inlet on the rear of the unit. 2. Insert the other end o f the power cord into the AC power supply . The unit powers up ...

  • Avaya 03-300686 - page 131

    1151B1 and 1151B2 Power Supplies Issue 3 January 2008 131 Connecting the cables T o connect IP telephones, PCs, servers, routers, workst ations, and hubs. 1. Connect the Ethernet connection cable (not supplied) to a 10/100 megabit s per second port on the front p anel of the Avaya C360 series switch . Note: Note: Use standa rd RJ45 connections and ...

  • Avaya 03-300686 - page 132

    Installing and wiring telephone power supplies 132 Installing and Connect ing the MDF and Telephones Import ant safety instructions for 1 151B1 and 1 151B2 Power Supplies Please read the following help ful tips. Retain these tip s for later use. When using this power supply , the following safe ty precaution s should always be followed to reduce th ...

  • Avaya 03-300686 - page 133

    1151B1 and 1151B2 Power Supplies Issue 3 January 2008 133 ! CAUTION: CAUTION: The power supply can be used only with telecommun ications equipment, indoors, and in a controlled environment . The power supply has a single output of -48 V DC, 0.4 amperes and can operate from eithe r a 120 V AC 60 hertz power source (105 to 129 V AC) or a 220/230/240 ...

  • Avaya 03-300686 - page 134

    Installing and wiring telephone power supplies 134 Installing and Connect ing the MDF and Telephones ...

  • Avaya 03-300686 - page 135

    Issue 3 January 2008 135 Chapter 8: T esting the complete configuration This section provides test s for the complete c onfiguration, including the control an d signaling networks and the telephones an d consoles. This section provides test s to: ● review the status of th e configuration. ● test the duplication link to the servers (S8700-series ...

  • Avaya 03-300686 - page 136

    Testing the complete con figuration 136 Installing and Connect ing the MDF and Telephones T esting port network equipment These test s verify that the time division mult ip lexing (TDM) cables and terminators work. If a FA I L Result code is seen, check these cables. If problems persist, see the maintenance book for your configuration. Checking por ...

  • Avaya 03-300686 - page 137

    Testing port network equipment Issue 3 January 2008 137 Figure 60: Sample port network st atus screen for Cabinet 1—A vaya S8500 Checking circuit p ack configuration The list configuration report provi des a list o f circuit packs c onnected to the configuration and recognized by the sof tware. T o check circuit pack configuration: 1. T ype list ...

  • Avaya 03-300686 - page 138

    Testing the complete con figuration 138 Installing and Connect ing the MDF and Telephones Figure 61: Sample sys tem configuration screen — Page 4, A vaya S8700 Multi-Connect T esting the TN2312BP Internet Protocol Server Interface circuit p ack T o test the TN2312BP Internet Protocol Serv er Interface circuit p a ck using Avaya Site Administratio ...

  • Avaya 03-300686 - page 139

    Testing port network equipment Issue 3 January 2008 139 Figure 62: Sample IPSI 01A test result s screen — Page 1, A vaya S8700 Multi-Connect T esting Exp ansion Interface circuit packs, if used T o check each Expansion Interface (EI) circuit pack in the media gateway: 1. T ype test board UUC SS where UUCSS is the cabinet, and slot for an EI circu ...

  • Avaya 03-300686 - page 140

    Testing the complete con figuration 140 Installing and Connect ing the MDF and Telephones Figure 63: Sample test result s for Exp ansion Interface Board 2A01 T esting time division multiplexing bus for each port network T o check each TDM bus for each port ne twork (PN) in the configuration. 1. T ype test tdm port-network 1 a nd press Enter . 2. V ...

  • Avaya 03-300686 - page 141

    Testing port network equipment Issue 3 January 2008 141 T esting exp ansion interface exchange, if used, for each port network If the configuration is critica l reliability , te st the expansion interface exchange for each PN: 1. T ype status port-network number < 1-64 > and press Enter . This displays the st andby expansion link. See Figure ...

  • Avaya 03-300686 - page 142

    Testing the complete con figuration 142 Installing and Connect ing the MDF and Telephones Figure 66: Sample of port network s t atus af ter exp ansion link is set Saving translations, if required ● T ype save translations and press Enter to save t he translations to the hard drive. T esting telephones and other equipment This section describes ho ...

  • Avaya 03-300686 - page 143

    Testing telephones and other eq uipment Issue 3 January 2008 143 ● T esting external ringing on page 144 ● T esting queue warning indicator on p age 144 ● T esting integrated announcement on p age 144 ● T esting music-on-h old on page 145 ● T esting emergency transfer (A vaya S8700 Multi-Connect only) on p age 145 ● T esting terminating ...

  • Avaya 03-300686 - page 144

    Testing the complete con figuration 144 Installing and Connect ing the MDF and Telephones T esting selector console T o check that all selector console lamp s are operational and make a call to a telephone in the configuration: 1. Simult aneously press and hold Ringer V olume up and POS BUSY on the attendant console. This put s the console in the s ...

  • Avaya 03-300686 - page 145

    Testing telephones and other eq uipment Issue 3 January 2008 145 Record an announcement T o record an announcement: 1. Select a test telep hone with console permissions enabled. 2. Dial the access cod e followed by th e integrated announcement extension number . 3. When you hear a dial tone, press 1 . When you hear a b eep or stutter tone, speak th ...

  • Avaya 03-300686 - page 146

    Testing the complete con figuration 146 Installing and Connect ing the MDF and Telephones T esting terminating trunk transmission The terminating trunk transmission test prov ides for extension number access to 3 tone sequences that can be used for trunk tran smission te sting from the dist ant end of the trunks. T o test terminating trunk transmis ...

  • Avaya 03-300686 - page 147

    LED indicators Issue 3 January 2008 147 T esting connectivity to the LAN T o test the external IP connections for the C-LA N, IP Media Processor , and V AL circuit packs, you must ping the circuit p ack and ping a know n computer conn ected to your network. If everything is configured correctly , the Result column on the Ping Result s screen reads ...

  • Avaya 03-300686 - page 148

    Testing the complete con figuration 148 Installing and Connect ing the MDF and Telephones T elephone console LEDs T elephones and attendant co nsoles have some alarm LEDs that must be checked out. Attendant console LEDs The console has two red LED s, labeled “ALM” and “ACK”. The ALM LED light s steadily when there is a major or minor alarm ...

  • Avaya 03-300686 - page 149

    LED indicators Issue 3 January 2008 149 Figure 67: TN1654 DS1 Converter circuit p ack LEDs The yellow LED indicates the st ate of the fiber interface, the fiber channel, the control channel, and the communications link to the SPE in the following manner and order of priority . See T able 23: DS1 Converter yellow LED flashing states . . Figure notes ...

  • Avaya 03-300686 - page 150

    Testing the complete con figuration 150 Installing and Connect ing the MDF and Telephones SP AN LEDs The four SP AN LEDs indicate the status of the fo ur T1/E1 facilities. A SP AN LED is in one of the following states: ● Solid on yellow: Facility is operational and alarm free. ● Blinking yellow for 2 seconds, of f 0.1 seconds: Facility is opera ...

  • Avaya 03-300686 - page 151

    Issue 3 January 2008 151 Index Index Numerical 110A-type terminal blocks (G650) . . . . . . . . . . 19 110P-type terminal blocks, frame-mounting . . . . . 24 110-type hardware . . . . . . . . . . . . . . . . . 17 110-type hardware, SCP-110 sneak current pr otection 54 110-type terminal blocks . . . . . . . . . . . . . . 19 110-type terminal bl ocks ...

  • Avaya 03-300686 - page 152

    152 Installing and Con necting the MDF and Telephones Index installing between cabinet and MDF . . . . . . . 38 outputs for control ca rrier . . . . . . . . . . . . 81 cables, installing between auxiliary cabinet and MDF . 39 cabling installing trunk cables . . . . . . . . . . . . . . 38 labels . . . . . . . . . . . . . . . . . . . . . 33 provision ...

  • Avaya 03-300686 - page 153

    Issue 3 January 2008 153 Index coupled bonding conducto rs . . . . . . . . . . . 58 data link protector . . . . . . . . . . . . . . . . 95 external ringing . . . . . . . . . . . . . . . . . 106 ITW Linx enhanced protector . . . . . . . . . . 95 MDF . . . . . . . . . . . . . . . . . . . . . . 19 MDFMain Distribution F rame. See MDF patch cords and j ...

  • Avaya 03-300686 - page 154

    154 Installing and Con necting the MDF and Telephones Index Q queue warning indicator . . . . . . . . . . . . . . 107 testing . . . . . . . . . . . . . . . . . . . . . 144 R recorded announcement, testing . . . . . . . . . . 145 ringing, testing . . . . . . . . . . . . . . . . . . . 144 routing cables to MDF . . . . . . . . . . . . . . . 36 S safet ...

  • Avaya 03-300686 - page 155

    Issue 3 January 2008 155 Index 1146B power distribution un it . . . . . . . . . . 11 7 2-wire digital station . . . . . . . . . . . . . . . 75 alarm . . . . . . . . . . . . . . . . . . . . . 75 analog station . . . . . . . . . . . . . . . . . 75 analog tie trunk . . . . . . . . . . . . . . . . . 76 battery . . . . . . . . . . . . . . . . . . . . . ...

  • Avaya 03-300686 - page 156

    156 Installing and Con necting the MDF and Telephones Index ...

Produzent Avaya Kategorie Telephone

Dokumente, die wir vom Produzenten des Geräts Avaya 03-300686 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Avaya
- Bedienungsanleitungen 03-300686
- Produktkarten Avaya
- Informationsbroschüren
- oder Energieetiketten Avaya 03-300686
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Avaya 03-300686.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Avaya 03-300686, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Avaya 03-300686. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Avaya 03-300686 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Avaya 03-300686, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Avaya 03-300686 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Avaya 03-300686 verständlich ist.

Eine gänzliche Bedienungsanleitung von Avaya sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Avaya 03-300686 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Avaya 03-300686 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Avaya 03-300686, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Avaya 03-300686 - die uns die ersten Schritte während der Nutzung von Avaya 03-300686 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Avaya 03-300686 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Avaya 03-300686 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Avaya 03-300686?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Avaya 03-300686 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Avaya 03-300686 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)