Bedienungsanleitung Barco R9000893

55 Seiten 2.1 mb
Download

Zur Seite of 55

Summary
  • Barco R9000893 - page 1

    GRAPHICS 1208s R9000893 R9000896 OWNER'S MANUAL ...

  • Barco R9000893 - page 2

    BARCO PROJECTION SYSTEMS Date : 220197 Art. No. : R5975847 GRAPHICS 1208s R9000893 R9000896 OWNER'S MANUAL ...

  • Barco R9000893 - page 3

    Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, January 1997. All rights reserved. Trademarks are the rights of their respective owners. Printed in Belgium BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium ...

  • Barco R9000893 - page 4

    Table of Contents i-1 5975847 BARCOGRAPHICS 1208S 220197 Table of contents .............................................................................................................. ............................................................. i Safety instructions ................................................................................ ...

  • Barco R9000893 - page 5

    Table of Contents i-2 5975847 BARCOGRAPHICS 1208S 220197 Blanking Adjustments ........................................................................................................... ............................................. 6-15 Convergence Adjustment .......................................................................................... ...

  • Barco R9000893 - page 6

    Safety Instructions 1-1 5975847 BARCOGRAPHICS 1208S 220197 WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These l ...

  • Barco R9000893 - page 7

    Safety Instructions 1-2 5975847 BARCOGRAPHICS 1208S 220197 A. Mains lead (Power cord) with CEE 7 plug : The wires of the mains lead are colored in accordance with the following code. Green and yellow: earth (safety earth) Blue: neutral Brown: line (live) B. Power cord with ANSI 73.11 plug : The wires of the power cord are colored in accordance with ...

  • Barco R9000893 - page 8

    Location and Functions of Control 2-1 5975847 BARCOGRAPHICS 1208S 220197 2 LOCA TION AND FUNCTION OF CONTROLS REAR PANEL TERMINOLOGY Communication Port (800 peripherals) * allows communication between the RCVDS switcher and the projector. * allows connection of a remote IR receiver unit to the projector. Port 3 RGB Analog Input (9 pin female sub D ...

  • Barco R9000893 - page 9

    Location and Functions of Control 2-2 5975847 BARCOGRAPHICS 1208S 220197 b. RCU control panel terminology This remote control includes a battery powered infrared (IR) transmit- ter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set-up. It includes automatic storing o ...

  • Barco R9000893 - page 10

    Connections 3-1 5975847 BARCOGRAPHICS 1208S 220197 hm ON T 1 EO) PRO JECT OR M ODE PO WER/M AI NS PO RT 2 (S-VIDEO) 75 o hm ON OFF GREEN : operati on al RED : stan d- by 352 3 CONNECTIONS AC Power (mains) Cord Connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector ...

  • Barco R9000893 - page 11

    Connections 3-2 5975847 BARCOGRAPHICS 1208S 220197 PROJECT OR WARM UP A FULL WHITE PATTERN WI LL BE GE NE RA TED FOR 20 MIN UTES. FOR IMMEDIATE USE OF THE PROJEC TO R, PRESS <EXIT>. WA RNI NG : SKIP PI NG THIS PRO CED URE C AN REDUC E THE I NITIAL PI CTURE QUALITY OF THE PROJECTED IMAGE. THI S OP TIO N CAN B E DISABLED I N THE SERVICE MENU Wh ...

  • Barco R9000893 - page 12

    Connections 3-3 5975847 BARCOGRAPHICS 1208S 220197 Connecting a Composite Video source to port 1. Video input selection : with the RCU or the build in RCU : press digit button 1 * Note : if using the loop-through Video output, then set the Termination Switch to the "OFF" position. Connecting a S-Video or Video source to port 2. Separate Y ...

  • Barco R9000893 - page 13

    Connections 3-4 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source to port 3. Connect your RGB source via an interface to Port 3. Always use an interface when a computer and local monitor have to be connected to the projector. Barco interfaces which can be applied : Universal analog interface R9826100 RGB 120 MHz analog interface R98 ...

  • Barco R9000893 - page 14

    Connections 3-5 5975847 BARCOGRAPHICS 1208S 220197 Connecting a RGB Analog source with Tri-level sync to port 4/5. (option) RGB analog input terminals with Tri level sync input or with Tri-level sync on green. The projector detects automatically where the sync signal is located. RGB input selection : (RG3sB : R, G, B signals with automatic Tri-leve ...

  • Barco R9000893 - page 15

    Connections 3-6 5975847 BARCOGRAPHICS 1208S 220197 PERIPHERAL EQUIPMENT Connecting a RCVDS 05 switcher to the BARCOGRAPHICS 1208s - Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs when 10 RCVDS switchers are linked via the expansion modules. - Serial communication with the projector. - Remote control buttons on the RCVDS to control t ...

  • Barco R9000893 - page 16

    Controlling 4-1 5975847 BARCOGRAPHICS 1208s 220197 4 CONTROLLING Caution : Do not display a stationary image with full brightness and contrast for longer than 20 min., otherwise you risk damage to the CRT's. Battery installation in the RCU. A new battery (not yet installed to save the battery life) is delivered inside the plastic bag with the ...

  • Barco R9000893 - page 17

    Controlling 4-2 5975847 BARCOGRAPHICS 1208s 220197 The BARCOGRAPHICS 1208s can be controlled with a. the RCU b. the hardwired RCU (cable not included) c. the built-in RCU (local keypad) The procedure and results of controlling the projector with either of these RCU options is essentially the same. How to use your RCU a) Point the front of the RCU t ...

  • Barco R9000893 - page 18

    Controlling 4-3 5975847 BARCOGRAPHICS 1208s 220197 Port No Projector input Press Digit Button 1 Comp. Video 1 2 S-Video 1 /Comp. Video* 2 3 RGB 2 3 4/5 RGB 2 4 or 5 4/5 Component video 3 6 4/5 RGB with Tri level sync 4 7 4/5 Component video with Tri-level sync 5 8 How to display a projector address? Press the ADDRESS key (recessed key on the RCU) w ...

  • Barco R9000893 - page 19

    Controlling 4-4 5975847 BARCOGRAPHICS 1208s 220197 Analog Picture Controls The analog picture controls can be adjusted with the RCU. The control keys are located on the lower right side of the key panel of the RCU and indicated with the name of the control and an icon. When an analog picture control is pressed, a text box with bar scale and the fun ...

  • Barco R9000893 - page 20

    Start Up of the Adjustment Mode 5-1 5975847 BARCOGRAPHICS 1208S 220197 5 ST ART UP OF THE ADJUSTMENT MODE Adjustment Mode All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Press the ADJUST key to enter the 'adjustment mode'. You are now in the 'Adjustment mode' . The Control stic ...

  • Barco R9000893 - page 21

    Start Up of the Adjustment Mode 5-2 5975847 BARCOGRAPHICS 1208S 220197 Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (Password protection is only available when the password DIP switch on the controller module is in the ON position. Contact a BARCO authorized t ...

  • Barco R9000893 - page 22

    Random Access Adjustment Mode 6-1 5975847 BARCOGRAPHICS 1208S 220197 6 RANDOM ACCESS ADJUSTMENT MODE Starting-Up the Random Access Adjustment mode. Push the control stick forward or backward to highlight "RANDOM ACCESS" and then press ENTER . Some items in the Random access mode are password protected (when the password function is enable ...

  • Barco R9000893 - page 23

    Random Access Adjustment Mode 6-2 5975847 BARCOGRAPHICS 1208S 220197 RANDOM ACCESS ADJUSTMENT MODE H SIZE V SIZE BLANKING LEFT BOTTOM RIGHT TOP V LINEARITY COARSE ADJUSTMENT From next page From next page SETUP PATTERN SELECTION FOCUSING BLUE GREEN RED BLUE GREEN RED RED AND BLUE BLUE AND GREEN RED AND GREEN COLOR SELECT ORBITING CONTRAST MODULATION ...

  • Barco R9000893 - page 24

    Random Access Adjustment Mode 6-3 5975847 BARCOGRAPHICS 1208S 220197 Selecting Setup Pattern If an external source is connected to the projector, this menu will be displayed. Push the control stick forward or backward to highlight the desired setup pattern and then press ENTER . Genlocked pattern : internally generated cross hatch pattern, locked o ...

  • Barco R9000893 - page 25

    Random Access Adjustment Mode 6-4 5975847 BARCOGRAPHICS 1208S 220197 Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MODE PICTURE TUNING GEOMETRY CONVERGENCE FOCUSING COLOR SELECT ORBITING CONTR. MODULATION SOFT EDGE Select with or <ENTER> to accept <EXIT> to return. PICTURE TUNING COLOR BALANCE SYNC : ...

  • Barco R9000893 - page 26

    Random Access Adjustment Mode 6-5 5975847 BARCOGRAPHICS 1208S 220197 Sync Fast/Slow Adjustment The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image. Highlight SYNC by pushing the control stick forward or backward and press ENTER to toggle between FAST and SLOW . Note: SYNC is normally used in the S ...

  • Barco R9000893 - page 27

    Random Access Adjustment Mode 6-6 5975847 BARCOGRAPHICS 1208S 220197 Port 2 : Video or S-Video Port 2 can be used as a Video or S-Video input. Highlight Port 2 by pushing the control stick forward or backward and press ENTER to toggle between VIDEO and S-VIDEO. Select with or <ENTER> to accept <EXIT> to return. PICTURE TUNING COLOR BALA ...

  • Barco R9000893 - page 28

    Random Access Adjustment Mode 6-7 5975847 BARCOGRAPHICS 1208S 220197 Focusing Before starting the 'focusing' adjustment, be sure the lenses are correctly focused. Push the control stick forward or backward to select 'Focusing' and press ENTER . Select with or then <ENTER> <EXIT> to return. RANDOM ACCESS ADJUSTMENT MO ...

  • Barco R9000893 - page 29

    Random Access Adjustment Mode 6-8 5975847 BARCOGRAPHICS 1208S 220197 Geometry Adjustments The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity an ...

  • Barco R9000893 - page 30

    Random Access Adjustment Mode 6-9 5975847 BARCOGRAPHICS 1208S 220197 Raster Shift Adjustment The green raster must be centered both horizontally and vertically on the center of the CRT surface. To center the green raster, look into the green lens and use the control stick to move the raster. CAUTION It is necessary to look into the lenses to perfor ...

  • Barco R9000893 - page 31

    Random Access Adjustment Mode 6-10 5975847 BARCOGRAPHICS 1208S 220197 Left-Right (east-west) Adjustments Left-right adjustments affect only the vertical lines of the projected image. Only the green image is displayed while making left-right adjustments. The red and blue images will automatically be corrected in the same manner. Convergence correcti ...

  • Barco R9000893 - page 32

    Random Access Adjustment Mode 6-11 5975847 BARCOGRAPHICS 1208S 220197 Seagull correction Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, still a 'S' deformation is visible on the left and the right side of the image. The default value on the bar scale for this correction is 50. Push the ...

  • Barco R9000893 - page 33

    Random Access Adjustment Mode 6-12 5975847 BARCOGRAPHICS 1208S 220197 Top-Bottom (north-south) Adjustments Top-Bottom and center adjustments affect only the horizontal lines of the projected image. To start up the Top-Bottom and center corrections, follow the next procedure : Push the control stick forward or backward to highlight TOP-BOT- TOM (N/S ...

  • Barco R9000893 - page 34

    Random Access Adjustment Mode 6-13 5975847 BARCOGRAPHICS 1208S 220197 Seagull Correction Use this correction after the image has been adjusted with top and bottom bow and keystone. If still a deformation (like a seagull) on top and bottom of the image is visible, proceed to the seagull correction. Due to interaction, it is possible that the top and ...

  • Barco R9000893 - page 35

    Random Access Adjustment Mode 6-14 5975847 BARCOGRAPHICS 1208S 220197 Vertical Linearity Adjustment The vertical linearity adjustment function corrects for vertical non- linearities which extend from the center of the image to the top and bottom of the image. Push the control stick forward or backward to highlight V LINEARITY on the Geometry menu a ...

  • Barco R9000893 - page 36

    Random Access Adjustment Mode 6-15 5975847 BARCOGRAPHICS 1208S 220197 Blanking Adjustments Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A 0% on the bar scale indicates no blanking. To start up the Blanking adjust ...

  • Barco R9000893 - page 37

    Random Access Adjustment Mode 6-16 5975847 BARCOGRAPHICS 1208S 220197 Convergence Adjustment Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image. Start with t ...

  • Barco R9000893 - page 38

    Random Access Adjustment Mode 6-17 5975847 BARCOGRAPHICS 1208S 220197 Vertical corners Highlight 'Vertical corners' and press ENTER to start the adjustment. To make a coarse adjustment of the red or blue horizontal lines in zone 10, 14, 18 and 22 simultaneously. Select with or then <ENTER> <EXIT> to return. COARSE CONVERGENCE ...

  • Barco R9000893 - page 39

    Service Mode 7-1 5975847 BARCOGRAPHICS 1208S 220197 Starting up the Service mode. Use the control stick to highlight 'Service' and then press ENTER . Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also free available ...

  • Barco R9000893 - page 40

    Service Mode 7-2 5975847 BARCOGRAPHICS 1208S 220197 Identification Highlight 'Identification' with the control stick and press ENTER . The 'Identification' screen gives information concerning : - projector address. To change the address of your projector, contact a qualified service technician. - software version. - configuratio ...

  • Barco R9000893 - page 41

    Service Mode 7-3 5975847 BARCOGRAPHICS 1208S 220197 Deletion of blocks This item is password protected. The delete function is used to clear all data (settings) from an adjustment block. A delete can be given : - block by block or - for all blocks. Deleting block by block The delete a block function deletes the settings of a selected block. Highlig ...

  • Barco R9000893 - page 42

    Service Mode 7-4 5975847 BARCOGRAPHICS 1208S 220197 Change password This item is password protected. Highlight 'change password' with the control stick and press ENTER . The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control stick to the left or to the right to select the digits to b ...

  • Barco R9000893 - page 43

    Service Mode 7-5 5975847 BARCOGRAPHICS 1208S 220197 Set to midposition Item is password protected. Highlight 'set to midposition' with the control stick and press ENTER to set all settings to their midposition. A confirmation menu will be displayed first. Select with or then <ENTER> <EXIT> to return. SERVICE MODE IDENTIFICATIO ...

  • Barco R9000893 - page 44

    Service Mode 7-6 5975847 BARCOGRAPHICS 1208S 220197 When undo is pressed all convergence settings are reset to the previous settings. Dynamic Astigmatism (spot shape adjustment) The spot shape adjustments correct the spot shape in 8 different areas on the screen and that for the three colors separately. The spot shape is adjusted according to the a ...

  • Barco R9000893 - page 45

    Service Mode 7-7 5975847 BARCOGRAPHICS 1208S 220197 Use the up and down arrow keys for the diagonal astigmatism adjustment and the left and right arrow keys for the axial astigmatism adjustment. Press ENTER to continue selecting a new area. The adjustment direction (axial or diagonal) and adjustment value are given in a text box on the screen. When ...

  • Barco R9000893 - page 46

    Service Mode 7-8 5975847 BARCOGRAPHICS 1208S 220197 Projector Warm Up Highlight 'Projector Warm Up' by pushing the control stick forward or backward and press ENTER to select the projector warm up menu. Select with or then <ENTER> <EXIT> to return. SERVICE MODE G2 ADJUSTMENT GAMMA CORRECTIONS CRT RUN IN CYCLE PROJECTOR WARM UP ...

  • Barco R9000893 - page 47

    Messages, warnings and failure codes 8-1 5975847 BARCOGRAPHICS 1208S 220197 8 MESSAGES, W ARNINGS AND F AILURE CODES SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz SOURCE 01 Fh= 15.6 kHz Fv= 050 Hz Announcement of the selected source. enter password xxxx Message to enter your password. Password contains 4 digits. text on text off These messages will be dis- pla ...

  • Barco R9000893 - page 48

    Messages, warnings and failure codes 8-2 5975847 BARCOGRAPHICS 1208S 220197 WARNING : go to stand by Projector will switch to 'stand-by' when the RCVDS is no longer available. WARNING : invalid frequency input The entered frequency or ap- plied frequency of the source is out of the projector's range. WARNING : default settings loaded ...

  • Barco R9000893 - page 49

    Options 9-1 5975847 BARCOGRAPHICS 1208S 220197 IR Receiver 800 This infrared receiver unit makes it possible to control the BARCOGRAPHICS 1208S from another room. There is a communication line with cable between the IR receiver and the projector or the RCVDS05. The control information from the RCU can now be sent to this IR receiver. The IR receive ...

  • Barco R9000893 - page 50

    Options 9-2 5975847 BARCOGRAPHICS 1208S 220197 MAGIK Interface Multifuctional Analog Graphics Interface Kit. BARCO's MAGIK interface allows the user to connect a presentation device such as a projector or a professional monitor to any computer with analog video signal with or without maintaining the connection with its own display. The MAGIK i ...

  • Barco R9000893 - page 51

    Orbiting A-1 5975847 BARCOGRAPHICS 1208S 220197 A ORBITING Orbiting (option) Static pictures are very often shown on large screen projectors, espectially in process control and presentation applications. Due to the fact that the same picture information is shown for a long period on the same place, picture tubes can be damaged by 'local burn-i ...

  • Barco R9000893 - page 52

    Orbiting A-2 5975847 BARCOGRAPHICS 1208S 220197 Orbiting Speed Toggle (only in MASTER Orbiting) Highlight 'SPEED : SLOW' with the control stick and press ENTER to set the ORBITING SPEED to Fast. Highlight 'SPEED : FAST' with the control stick and press ENTER to set the ORBITING SPEED to Slow <EXIT> to return. MASTER ORBITI ...

  • Barco R9000893 - page 53

    Orbiting A-3 5975847 BARCOGRAPHICS 1208S 220197 Adjustment procedure multiple projector installations : Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum. Default setting of the Master projectorn see 'Stand-Alone projector'. Highlight &a ...

  • Barco R9000893 - page 54

    Adjustment Blocks and Source Numbers 90-99 B-1 5975847 BARCOGRAPHICS 1208S 220197 Adjustment Blocks (memory blocks) As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector ’ s memory as numeric values. These numeric values are used to control digital potentiometers which in turn, control the ...

  • Barco R9000893 - page 55

    Insert Card i-1 5975847 BARCOGRAPHICS 1208S 220197 P RCU INP UT S O URCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INP UT S O URCE S 7 P RCU INP UT S O URCE S 1 PROJECTOR RCV DS 2 3 4 5 6 1 2 3 5 6 7 8 9 10 INP UT S O URCE S 7 INSERT CARD ...

Produzent Barco Kategorie Wheelchair

Dokumente, die wir vom Produzenten des Geräts Barco R9000893 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Barco
- Bedienungsanleitungen R9000893
- Produktkarten Barco
- Informationsbroschüren
- oder Energieetiketten Barco R9000893
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Barco R9000893.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Barco R9000893, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Barco R9000893. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Barco R9000893 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Barco R9000893, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Barco R9000893 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Barco R9000893 verständlich ist.

Eine gänzliche Bedienungsanleitung von Barco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Barco R9000893 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Barco R9000893 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Barco R9000893, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Barco R9000893 - die uns die ersten Schritte während der Nutzung von Barco R9000893 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Barco R9000893 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Barco R9000893 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Barco R9000893?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Barco R9000893 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Barco R9000893 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)