Bedienungsanleitung Clarion MCD360

16 Seiten 0.28 mb
Download

Zur Seite of 16

Summary
  • Clarion MCD360 - page 1

    ...

  • Clarion MCD360 - page 2

    INTRODUCTION The Clarion MCD360 is a full-featured Three-Way Crossover. When used to build a 2-way system with front and rear fader capability or a full three-way system, the Clarion MCD360 electronic crossover allows you to choose from a wide range of crossover points between the front, rear and subwoofer outputs. The MCD360 includes the following ...

  • Clarion MCD360 - page 3

    INPUT/OUTPUT CONNECTIONS AND AUDIO CONTROLS The top panel of MCD360 contains the controls for the crossover and output levels as shown below. 3 1. Front RCA Input 2. Front Crossover Frequency Control 3. Front/Rear Input Selection Switch 4. Rear RCA Input 5. Rear Crossover Frequency Control 6. Sub Input Selection Switch 7. Sub RCAInput 8. Sub Crosso ...

  • Clarion MCD360 - page 4

    • Front High-Pass Crossover Frequency Adjustment - Adjusts the crossover to match your speaker system. The crossover frequency can be adjusted from 32Hz - 400Hz or from 640Hz - 8kHz with the crossover frequency multiplier switch. • Rear High-Pass Crossover Frequency Adjustment - Adjusts the crossover to match speaker your system. The crossover ...

  • Clarion MCD360 - page 5

    MOUNTING PRECAUTIONS The MCD360 crossover can be mounted in any convenient location in your vehicle that allows access to the controls and is away from moisture. The flanges on the chassis have mounting holes which can be used as a template for screw holes. For easy system set-up, mount the crossover so the front panel controls will be accessible a ...

  • Clarion MCD360 - page 6

    WIRING PRECAUTIONS Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer . If you are using a source unit, without a remote turn-on lead, the MCD360 can be turned on with a switched accessory lead. Y ou can find this accessory power source in the factory harness at the back of the radio. It is t ...

  • Clarion MCD360 - page 7

    7 Figure 3 - Electrical connections for the MCD-360 ...

  • Clarion MCD360 - page 8

    APPLICA TIONS The MCD360 allows you to design either a 2-way system with front and rear output or a full 3-way system. After determining which system best fits your requirements, thoroughly read and follow the directions below for your system type. 2-Way System with Front and Rear Output 8 Figure 4 - In this illustration, the MCD360 is configured f ...

  • Clarion MCD360 - page 9

    9 For 2 channel input, configure switches as shown. For 4 channel input with front and rear fade, configure switches as shown. For front and rear fade with dedicated subwoofer input, configure switches as shown. Figure 5- ...

  • Clarion MCD360 - page 10

    2-Way System Application Notes After all the wiring connections are made and before the system is turned on for the first time, you need to make some basic adjustments. It is important that the High-Pass and Low-Pass Frequency Controls are set correctly before turning on the system for the first time. Setting the Crossover Frequency Controls 1. Set ...

  • Clarion MCD360 - page 11

    Setting the Rear Output Level Before setting rear level controls, disconnect both the front output and the subwoofer output and follow the directions below . 1. T urn the output control level to the minimum setting. 2. T urn the amplifier gain controls to the minimum setting. 3. T urn the source unit on and increase the volume until distortion is h ...

  • Clarion MCD360 - page 12

    3-Way System 12 Figure 6 - In this illustration, the MCD360 is configured for single channel input with dedicated amplifiers for tweeters, midranges and subwoofer(s). ...

  • Clarion MCD360 - page 13

    3-Way System Application Notes After all the wiring connections are made and before the system is turned on for the first time, you need to make some basic adjustments. It is important that the High-Pass and Low-Pass Frequency Controls are set correctly before turning on the system for the first time. Setting the Crossover Frequency Controls 1. Set ...

  • Clarion MCD360 - page 14

    Setting the Sub Output Level 1. Make sure all ouputs are connected and both the front and rear output levels are set correctly. Unplug the Remote Sub Level control cable. 2. Be sure the sub output level and amplifier gains are at their minimum settings. 3. W ith the volume set at a medium level, slowly increase the sub level control to the point wh ...

  • Clarion MCD360 - page 15

    Problem: Midrange speakers “pop” with loud passages. Solution: High-Pass Frequency Control is set too low . Gain Controls on amplifiers are set incorrectly. Reduce the gain setting on high frequency amplifier . Problem: One channel does not operate. Solution: Swap left and right connections at the source unit. If the problem trades sides in the ...

  • Clarion MCD360 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com MCD360-10 Rev .1 (02/00) ...

Produzent Clarion Kategorie Stereo Equalizer

Dokumente, die wir vom Produzenten des Geräts Clarion MCD360 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Clarion
- Bedienungsanleitungen MCD360
- Produktkarten Clarion
- Informationsbroschüren
- oder Energieetiketten Clarion MCD360
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Clarion MCD360.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Clarion MCD360, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Clarion MCD360. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Clarion MCD360 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Clarion MCD360, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Clarion MCD360 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Clarion MCD360 verständlich ist.

Eine gänzliche Bedienungsanleitung von Clarion sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Clarion MCD360 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Clarion MCD360 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Clarion MCD360, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Clarion MCD360 - die uns die ersten Schritte während der Nutzung von Clarion MCD360 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Clarion MCD360 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Clarion MCD360 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Clarion MCD360?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Clarion MCD360 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Clarion MCD360 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)