Bedienungsanleitung Porter-Cable 8623

19 Seiten 0.26 mb
Download

Zur Seite of 19

Summary
  • Porter-Cable 8623 - page 1

    ESP AÑOL: PÁGINA 19 FRANÇAISE : P AGE 39 Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No. __________________________ ...

  • Porter-Cable 8623 - page 2

    2 SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry pr oducts, and • arsenic a ...

  • Porter-Cable 8623 - page 3

    3 ELECTRICAL SAFETY 1. Do not abuse the cord. Never use the cor d to carry the tool. Keep cord away fr om heat, oil, sharp edges or moving parts. Replace damaged cords immediately . Damaged cords incr ease the risk of electric shock. 2. A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specif ...

  • Porter-Cable 8623 - page 4

    4 7. Maintain tools with care. Keep cutting tools sharp and clean. Pr operly maintained tools with sharp cutting edge are less likely to bind and ar e easier to control. 8. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool serviced before ...

  • Porter-Cable 8623 - page 5

    5 ADDITIONAL SAFETY RULES FOR HAMMER DRILL/DRIVERS 1. Apply forward for ce only on pistol grip handle and ONL Y with your hands when drilling. 2. Do not use bits lar ger than those recommended. They may cause personal injury due to jamming and loss of control. Lar ge bits may also overload the drill and damage the motor and gears. 3. V erify that t ...

  • Porter-Cable 8623 - page 6

    3. Do not expose charger to rain, snow or frost. 4. Do not abuse cord. Never carry char ger by cor d or yank it to disconnect from r eceptacle. Pull by plug rather than cord when disconnecting char ger . Have damaged or worn power cord and strain reliever r eplaced immediately . DO NOT A TTEMPT TO REP AIR POWER CORD. 5. Make sure cor d is located s ...

  • Porter-Cable 8623 - page 7

    7 19. Dispose of expended batteries properly . The Porter -Cable Model 8823 Battery Pack contains rechar geable, nickel-cadmium batteries. These batteries must be recycled or disposed of pr operly . Drop of f expended battery packs at your local replacement battery r etailer , your local recycling center , or at a Porter -Cable Service Center (see ...

  • Porter-Cable 8623 - page 8

    8 INST ALLING AND REMOVING DRILL AND SCREWDRIVER BITS Always set the reversing button to the center (locked "OFF") position when installing and removing bits. 1. The three-jaw chuck is designed for self-centering of the bit. Open jaws lar ge enough by turning the sleeve (A) Fig. 2 counterclockwise, when viewing the chuck from the bit end, ...

  • Porter-Cable 8623 - page 9

    9 The low speed position is normally used when drilling lar ger holes and when driving or removing scr ews. The high speed position is normally used for drilling small holes. DRIVER BIT STORAGE Convenient storage areas with retaining clip (B) Fig. 4 for screwdriver bits ar e provided on each side of the tool. Fig. 4 A B Fig. 5 A B SIDE HANDLE Model ...

  • Porter-Cable 8623 - page 10

    10 OPERA TION CHARGING THE BA TTERY P ACK GENERAL Before using your cor dless tool for the first time, the battery pack should be fully char ged. If the battery pack is installed in the tool, remove it by following instructions under INST ALLING OR REMOVING BA TTER Y P ACK. As a battery pack approaches the dischar ged state, you will notice a sharp ...

  • Porter-Cable 8623 - page 11

    11 Problems will be indicated by char ger indicator lights (see Fig. 8): • If the green light (A) continues to flash after battery pack is inserted in char ger , the battery pack temperature is either too high or too low for char ging. If left alone, the charger will continue to monitor the battery pack temperature and will begin char ging when t ...

  • Porter-Cable 8623 - page 12

    12 HOW TO HOLD THE HAMMER DRILL/DRIVER The front end of the Hammer Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 10B. GENERAL DRILLING 1. Set torque adjusting collar for drilling operation and set speed selector to appropriate speed. ...

  • Porter-Cable 8623 - page 13

    13 DRILLING WOOD In addition to the instructions listed under "GENERAL DRlLLlNG", the following also apply: 1. When using twist drills in wood, withdraw them from the hole frequently to clear chips built up in flutes to avoid overheating and burning work. 2. If a backing block is used to keep back of work from splintering, clamp it secure ...

  • Porter-Cable 8623 - page 14

    14 2. Install proper bit that fits scr ew to screwdriver . 3. Set tor que adjusting collar for desired tor que and set speed selector to LOW . 4. Set screwdriver for corr ect rotation. 5. Start screw straight in hole with fingers. 6. Place bit on screw , remove fingers, start scr ewdriver , and exert pressure to drive screw . 7. As soon as screw ha ...

  • Porter-Cable 8623 - page 15

    MAINTENANCE KEEP TOOL CLEAN All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could very possibly dissolve or otherwise damage the material. F AILURE TO ST ART Should your tool fail to start, make sure battery pack is char ged and pr operly installed in drill. BA TTERY The battery pack will ...

  • Porter-Cable 8623 - page 16

    16 AL TERNA TE CHUCK REPLACEMENT Remove battery pack to prevent accidental start-up. 1. Open chuck jaws as wide as possible to gain access to the chuck retaining scr ew . 2. Remove chuck retaining scr ew by turning it clockwise (left-hand thread) with an hex wrench. 3. Place the two-speed gear shift selector to the rear (LOW) position. 4. Place the ...

  • Porter-Cable 8623 - page 17

    17 ACCESSORIES A complete line of accessories is available from your Porter -Cable • Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Porter - Cable Authorized Service Stations. Please visit our W eb Site www .porter -cable.com for a catalog or for the name of your nearest supplier . Since accessories other than those offer e ...

  • Porter-Cable 8623 - page 18

    18 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material ...

  • Porter-Cable 8623 - page 19

    60 The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL ...

Produzent Porter-Cable Kategorie Cordless Drill

Dokumente, die wir vom Produzenten des Geräts Porter-Cable 8623 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Porter-Cable
- Bedienungsanleitungen 8623
- Produktkarten Porter-Cable
- Informationsbroschüren
- oder Energieetiketten Porter-Cable 8623
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Porter-Cable 8623.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Porter-Cable 8623, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Porter-Cable 8623. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Porter-Cable 8623 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Porter-Cable 8623, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Porter-Cable 8623 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Porter-Cable 8623 verständlich ist.

Eine gänzliche Bedienungsanleitung von Porter-Cable sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Porter-Cable 8623 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Porter-Cable 8623 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Porter-Cable 8623, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Porter-Cable 8623 - die uns die ersten Schritte während der Nutzung von Porter-Cable 8623 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Porter-Cable 8623 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Porter-Cable 8623 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Porter-Cable 8623?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Porter-Cable 8623 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Porter-Cable 8623 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)