Bedienungsanleitung Coleman F*FP

16 Seiten 0.22 mb
Download

Zur Seite of 16

Summary
  • Coleman F*FP - page 1

    292043-UIM-B-0707 SINGLE PIECE AIR HANDLERS MODELS: F*FP INSTALLATION MANUAL ISO 9001 Certified Quality Management System SAFETY This is a safety alert symbol . When you see this symbol on labels or in manuals, be alert to the potential for personal injury . Understand and pay particular attention to the signal words D ANGER , WA R N I N G , or CAU ...

  • Coleman F*FP - page 2

    292043-UIM-B-0707 2 Unitary Products Group SPECIFIC SAFETY RULES AND PRE CA U TIONS 1. Install this air handler only in a location and position as specified in SECTION I of these instructions. 2. Always install the air handler to operate within the air handler ’s intended maximum outlet air t emperature. Only connect the air handler to a duct sys ...

  • Coleman F*FP - page 3

    292043-UIM-B-0707 Unitary Products Group 3 6. When an evaporator coil is instal led in an attic or above a finished ceiling, an auxiliary dr ain pan should be provided under the coil as is specified by most local building codes. 7. Proper electrical supply must be available. 8. Clearances must also be taken in to consideration, and provided for as ...

  • Coleman F*FP - page 4

    292043-UIM-B-0707 4 Unitary Products Group FIGURE 3: Filter Access & Drain Pan Conversion / Coil Baffle FIL TER 4B - SIDE VIEW "S" BRACKET MUST BE USED TO F ASTEN DUCT WORK T O FRONT OF UNIT RETURN AIR DUCT 3/4" PVC SOCKETS FOR HORIZONT AL DRAIN APPLICA TION HORIZONT AL DRAIN P AN POSITION "A” HORIZONT AL DRAIN P AN POSITI ...

  • Coleman F*FP - page 5

    292043-UIM-B-0707 Unitary Products Group 5 DUCT CONNECTIONS NOTE: The electric heat accessory s hould be installed before the sup- ply air duct is attached to the suppl y air openings. Refer to the electric heater kit instructions for proper installation. Air supply and return may be handled in one of several ways best suited to the installation. S ...

  • Coleman F*FP - page 6

    292043-UIM-B-0707 6 Unitary Products Group • If the suction line is 3/4" diamet er - position the bulb near the top of the copper tube as show n. If the tube is 7/8" diameter - position the bulb near the bottom of the tube. Refer to Figure 7. • Wrap the clamp, bulb & line securely with insulation provided. NOTE: The coil should be ...

  • Coleman F*FP - page 7

    292043-UIM-B-0707 Unitary Products Group 7 ...

  • Coleman F*FP - page 8

    292043-UIM-B-0707 8 Unitary Products Group LO W VOL T A GE CONTR OL CONNECTION The 24 volt power supply is provi ded by an int ernally wired low voltage transformer which is standard on all model s. However, if the unit is con - nected to a 208 volt power supply the low voltage transformer must be rewired to the 208 volt tap. See the unit wiring la ...

  • Coleman F*FP - page 9

    292043-UIM-B-0707 Unitary Products Group 9 TA B L E 3 : Physical and Electrical Data Models F*FP 024 030 036 040 Blower - Diameter x Width 10 x 6 10 x 8 10 x 8 10 x 8 Motor HP 1/4 1/3 1/2 1/3 Nominal RPM 1075 1075 1075 1075 V oltage 208/230 Amps Full Load (208/230) 1.6/1.4 (50 Hz:2.1) 2.5 / 2.2 3.3/2.9 (50 Hz:2.3) 2.5 / 2.2 Locked Rotor (208/230) 3 ...

  • Coleman F*FP - page 10

    292043-UIM-B-0707 10 Unitary Products Group * May be 0 (no breaker) or 1 (with breaker). TA B L E 6 : Electrical Data - 1 Ø - 2 08/230-1 -60 1 Models F*FP Heater* Model Max. St atic & Min. CFM T otal Heat 2 KW St aging 3 KW MBH W1 Only W2 Only W1 + W2 St atic T ap 208V 240V 208V 2 40V 208V 240V 2 08V 240V 208V 240V 024 2HK*6500506B 0.5 Low 3.8 ...

  • Coleman F*FP - page 11

    292043-UIM-B-0707 Unitary Products Group 11 * May be 0 (no breaker) or 1 (with breaker). TA B L E 7 : Electrical D a t a - (For Single Source Power Supply) - Copper W ire 1 Ø - 20 8/230-1-60 1 Models F*FP Heater* Model Heater Amps 240V Field W iring Min. Circuit Ampacity Max. O.C.P . 2 Amps /T ype 75 ° C Wir e Size - A WG 208V 240V 208V 240V 208V ...

  • Coleman F*FP - page 12

    292043-UIM-B-0707 12 Unitary Products Group TA B L E 9 : Electrical Data - 3 Ø - 2 08/230-3 -60 1 Models F*FP Heater 2 Model Max. St atic & Min. CF M T ot al Heat KW St aging 3 KW MBH W1 Only W2 On ly W1 + W2 St atic T ap 208 240 208 240 208 240 208 240 208 240 024 2HK06501025B 0.5 Low 7.5 10.0 25.6 34.1 3.8 5.0 7.5 5.0 7.5 10.0 030 2HK0650102 ...

  • Coleman F*FP - page 13

    292043-UIM-B-0707 Unitary Products Group 13 All F*FP series air handler unit s are UL Listed up to 0.50" w .c. external st atic pressure, including air filter , wet coil, and largest KW size heater . TA B L E 1 1 : Airflow Data for 2 30 V olt - Heat Pump Models 1 1. Includes Return Air Filter and Largest Electric Heate r. Models Blower Motor S ...

  • Coleman F*FP - page 14

    292043-UIM-B-0707 14 Unitary Products Group T A BLE 12: Airflow Data 1 for 208 V olt - Heat Pump Models 1. Includes Return Air Filter and Largest Electric Heate r . All F*FP series air handler unit s are UL Listed up to 0.50" w .c. external st atic pressure, including air filter , wet coil, and largest KW size heater . Models Blower Motor Spee ...

  • Coleman F*FP - page 15

    292043-UIM-B-0707 Unitary Products Group 15 NOTES: 1. “Y” T erm inal on Air Handler Control Bo ard must be connected for full CFM and applications requiring 60 second Blower Off Del ay for SEER enhancement. 2. 1 Optional Dehumidification Humidi stat con tacts open on rise. 3. For F4FV model - Remove Humidistat Jumper on CFM Selection Board - if ...

  • Coleman F*FP - page 16

    Subject to change without notice. Printed in U.S.A. 292043-UIM-B-0707 Copyright © by York International Corp. 2007. All rights reserved. Supersedes: 292043-UIM-A-0507 Unitary 5005 Norman Product Y ork OK Group Drive 73069 DRAIN CONNECTIONS All drain lines should be trapped a minimum of three inches, should be pitched away from unit dr ain pan and ...

Produzent Coleman Kategorie Air Conditioner

Dokumente, die wir vom Produzenten des Geräts Coleman F*FP erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Coleman
- Bedienungsanleitungen F*FP
- Produktkarten Coleman
- Informationsbroschüren
- oder Energieetiketten Coleman F*FP
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Coleman F*FP.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Coleman F*FP, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Coleman F*FP. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Coleman F*FP ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Coleman F*FP, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Coleman F*FP hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Coleman F*FP verständlich ist.

Eine gänzliche Bedienungsanleitung von Coleman sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Coleman F*FP bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Coleman F*FP befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Coleman F*FP, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Coleman F*FP - die uns die ersten Schritte während der Nutzung von Coleman F*FP erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Coleman F*FP hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Coleman F*FP im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Coleman F*FP?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Coleman F*FP nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Coleman F*FP hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)