-
Coleman 5110 - page 1
Gas Barbecue Use, Car e & Assembly Manual W ith Grill Lighting Instructions 5100 LP Gas Series 5110 Natural Gas Series ASSEMBLER/INST ALLER: Leave these instructions with the consumer . CONSUMER/USER: Read all these instructions and keep them in a safe place for future r eference. For Out door Use Only www .coleman.com I I M M P P O O R R T T A ...
-
Coleman 5110 - page 2
2 DANGER • FOR OUTDOOR USE ONL Y . NEVER operate grill in enclosed areas, as this could lead to gas accumulating from a leak, causing an explosion or a carbon monoxide buildup which could result in injury or death. DO NOT use in garages, breezeways, sheds or any enclosed area. (Fig. 1) • NOT FOR USE BY CHILDREN. (Fig. 2) • If these instructio ...
-
Coleman 5110 - page 3
3 1 3 2 24 " 8 7 36" (90cm) 36" (90cm) 36" (90cm) Clear REPRESENT A TIVE ILLUSTRA TION • Installation must conform with local codes or , in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1 (USA), CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149.2, Propane Inst allation Code (Canada). ...
-
Coleman 5110 - page 4
4 Longer detachable power-supply cords or extension cords must be used with care. The marked electrical rating of the cord set or extension cord must be at least as great as the electrical rating of the appliance. If the appliance is of the grounded type, the exten- sion cord should be a grounding-type 3-wire cord. Use outdoor extension cords with ...
-
Coleman 5110 - page 5
5 DANGER • DO NOT insert any foreign object s into the valve outlet. Y ou may damage the valve. A damaged valve can cause a leak, which could result in explosion, fire, severe per- sonal injury or death. W ARNING • Cylinders must be stored outdoors out of the reach of children and must not be stored in a building, garage or any other enclosed a ...
-
Coleman 5110 - page 6
6 W ARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P . gas supply cylinder under the grill body or inside grill enclosure or in the vicinity of any heat producing appliance. (Fig. 12) • NEVER fill the cylinder beyond 80% full. Failure to follow this information exactly could result in an expl ...
-
Coleman 5110 - page 7
Assembly/Set up ■ Remove components from p ackage. 7 Firebox Side Burner Rear Support Rear T rim Plate Side Burner Grate Right Side T able Left Side Burner T able Grates Burner Heat T ents™ Base T op Panel Left Panel Left Door Right Door Grease Pan Locking Casters Door Magnets T ool Hook Cylinder Support Right Panel Side Burner Knob Cylinder Re ...
-
Coleman 5110 - page 8
1-A . Arrange the two panels and the base on the ground as shown. Ö Ö LOOSEL Y assemble the Right Panel and the Left Panel to the Grill Base using one screw (TN) in each top corner . Ö Ö NOTE: Use a large piece of cardboard or a ground cloth to protect the painted finish on the grill. Step 1 1-B 1-B . LOOSEL Y assemble two fasteners (TN) into e ...
-
Coleman 5110 - page 9
Ö Ö Carefully turn the assembly up-side-down to perform Step 2. This will give easy access to assemble the parts in Step 2. 2-A . Carefully turn the grill Up-Side-Down. 2-A Base (up-side-down) 2-B . Assemble eight additional screws (TN) to fasten the Side Panels to the base Base. Ö Ö Tighten all fasteners. 2-B 2-A . Carefully turn the grill Up- ...
-
Coleman 5110 - page 10
Ö Ö NOTE: Use a ground cloth to protect the paint finish during this step. 2-A . Carefully turn the grill Up-Side-Down. 3-A 3-A . Check that all fasteners are tightened before turning the grill Right-Side-Up. Ö Ö Carefully turn the grill Right-Side-Up. Ö Ö Engage the Locking Casters to prevent movement during the rest of the assembly process. ...
-
Coleman 5110 - page 11
Ö Ö Assemble the T op Panel. Ö Ö Assemble the Rear Support. 5-A 5-A . Assemble the T op Panel to the Left and Right Side Panels with eight Screws (TN). Hardware shown actual size TN (x8) T op Panel Ö Ö Install Door Magnets. 5-B 5-B . Assemble the Rear Support to the Left and Right Side Panels with eight Screws (TN). Rear Support TN (x8) Hardw ...
-
Coleman 5110 - page 12
Ö Ö NOTE: Use a ground cloth to protect the paint finish during Step 7 and 8 . Ö Ö Assemble Right Side T able to the Firebox. 7-A 7-A . Lay the Firebox on it’s backside with lid closed . This will allow easy access to the fastener locations. Ö Ö Assemble the Right Side T able to the Firebox with five Screws (CX) and one Locking Hex Nut (UO) ...
-
Coleman 5110 - page 13
Ö Ö Assemble Left Side Burner Assembly to the Firebox. Hardware shown actual size (CX) M6 x 20mm Screw (5) Qty . (UO) M6 Locking Hex Nut (1) Qty . 8-A 8-A . Assemble the Left Side Burner T able to the Firebox with five Screws (CX) and one Locking Hex Nut (UO). Place the Locking Hex Nut in the center position as shown in 8-C . Ö Ö Tighten all fa ...
-
Coleman 5110 - page 14
Ö Ö Assemble Firebox to the Grill Cart. Ö Ö HINT : A second person is helpful when aligning the Firebox to the Grill Cart. 9-A 9-B 9-C 9-D 9-A . Carefully place the Firebox onto the Cart Assembly . T ake care to not damage the fuel hoses. They must be routed through the large hole in the top panel. See Step 9-B . 9-C . Make sure the Firebox pan ...
-
Coleman 5110 - page 15
Ö Ö Fasten the Firebox to the Grill Cart. 10-A 10-A . LOOSEL Y fasten the right side of the Firebox to the Grill Cart with three Screws (TN), two Flat W ashers (DY) and two Locking Hex Nuts (UO). Ö Ö NOTE: Y ou will tighten these screws LA TER (after Step 10-B), after the left side of the Firebox is attached to the Grill Cart (this helps with a ...
-
Coleman 5110 - page 16
Ö Ö Fasten the Rear T rim Plate to the Grill Cart. (VP) Self T apping Screw (2) Qty . Hardware shown actual size 1 1-A 1 1-A . Fasten the Rear T rim Plate to the Firebox with two Screws (VP). Ö Ö Tighten all fasteners. FIREBOX VP (x2) REAR TRIM PLA TE VP Step 11 16 1 1-B 1 1-B . View showing Rear T rim Plate properly installed. REAR TRIM PLA TE ...
-
Coleman 5110 - page 17
12-A Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty . Ö Ö Fasten both Left and Right Doors to the Grill Cart. Ö Ö Attach the T ool Hook to the Right Door . 12-C . Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). Ö Ö Repeat Step 12-C to attach the Left Door . Ö Ö Tighten all fasteners. 12-B . Squeez ...
-
Coleman 5110 - page 18
Ö Ö Install three Heat T ents™. Ö Ö Install three Cooking Grates. Ö Ö Install the W arming Rack. 13-A 13-B 13-C . Install three Cooking Grates, flat side downward. Ö Ö Locate the Power Grate in the center position. 13-C 13-B . Install three Heat T ents™ over the Burners. Ö Ö The Heat T ents™ are located using the alignment pins. 13- ...
-
Coleman 5110 - page 19
14-A Ö Ö Install the Side Burner V alve. 14-B Side Burner V alve 14-A . Route the Side Burner V alve through the Large Hole in the Left Panel. Large Hole 14-C 14-E 14-D 14-C . Attach the Side Burner V alve with two Screws (WQ). WQ (x2) View from Below View From Back of Grill View from Above Side Burner V alve Step 14 19 Hardware shown actual size ...
-
Coleman 5110 - page 20
15-D Ö Ö Assemble the Side Burner to the Left Side T able. Ö Ö Assemble the Electrode to the Side Burner . 15-A 15-B 15-A . Slip the Burner T ube through the Left Side T able. 15-D . View showing Side Burner properly installed. 15-B . Align Burner T ube with Burner V alve. Ö Ö NOTE: Make sure Burner V alve is inserted into Burner T ube. 15-C ...
-
Coleman 5110 - page 21
Ö Ö Assemble the Electrode Wires and the Battery to the Electrode Module. Note : The fuel hoses are not shown in this step, for simplicity . 16-A Side Burner Wire 9-V olt Battery T op Burner Wires Electrode Module 16-A . Slip the T op Burner Wires through the large hole in the T op Panel. Ö Ö Slip the Side Burner Wire through the large hole in ...
-
Coleman 5110 - page 22
Ö Ö Install Side Burner Knob and Side Burner Grate onto the Left Side Burner . 17-A Side Burner Knob Side Burner Grate 17-A . Place the Side Burner Knob on the valve stem. Ö Ö Place the Side Burner Grate on the Left Side Burner . Align the pins downward into the alignment holes. Ö Ö Assemble the Grease Cup Support to the Grease Pan. Note: The ...
-
Coleman 5110 - page 23
Ö Ö Install the Grease Pan. Ö Ö Install the Grease Cup. 19-A 19-B 19-A . Slide the Grease Pan Assembly into the back of the grill. Ö Ö Tilt the pan slightly upward until the Grease Cup Support clears the Rear Support. Rear Support 19-B . Place the Grease Cup into the Grease Cup Support. Note: Pull the Grease Pan outward slightly for easier ac ...
-
Coleman 5110 - page 24
Ö Ö Attach an LP Cylinder to the Grill. 20-A Cylinder Support LP Cylinder 20-A . Set LP Cylinder in the Cylinder Support with the outlet valve facing toward the front of the grill. 20-B 20-B . T ighten the Cylinder Hold-Down Bolt against the bottom cylinder collar . Cylinder Hold-Down Bolt 20-C T ype 1 Nipple Fuel V alve Outlet 20-C . Insert the ...
-
Coleman 5110 - page 25
Ö Ö NOTE: Step 21 applies to you only if your grill is set up from the factory to use NA TURAL GAS. If your grill is set up from the factory to use LP GAS, skip back to Step 20. Step 21 P LACE THE RUBBER PLUG ONT O THE GAS SUPPL Y LINE . T HEN A TT ACH THE SOCKET END OF THE QUICK DISCONNECT COUPLING ONTO THE GAS SUPPL Y LINE . T IGHTEN WITH A WRE ...
-
Coleman 5110 - page 26
26 1. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop. 2. Check that all the grill burner knobs are in the off position. 3. Remove the protective caps from the cylinder valve and cou - pling nut. NOTE: The coupling nut connect s to the large outside threads on the valve outlet. 4. Hold the regulator in ...
-
Coleman 5110 - page 27
CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear , replace the hoses prior to operating the appliance. During assembly of grill and when attaching or replacing the L. P . gas cylinder , insure that all gas supply hoses are free of kinks and/or damage and are at least 3" away from hot s ...
-
Coleman 5110 - page 28
28 1. T urn on any or all burner gas control knobs to high. (Fig. 19) 2. Press the igniter switch until the flame ignites. 3. If the flame doesn’t immediately light, turn off control knob and wait five minutes for gas to clear . 4. Repeat steps 1 through 3. 5. If the burner does not light on second try , turn off knob and try match-lighting the b ...
-
Coleman 5110 - page 29
Good Bad Y ellow Blue Holes in Burner Y ellow Blue Burner Control Setting Tip s • The high flame setting is too hot for direct cooking. The high flame setting is good for quick searing of meat, then finish cooking on medium or low flame settings. • Use high flame setting with lid closed to preheat the grill for 5 minutes before cooking and with ...
-
Coleman 5110 - page 30
Step s For Cleaning V enturi: 1. Remove burner from grill bottom. 2. Look inside lower end of venturi tubes for nests, webs or mud. 3. T o remove the above obstructions, use an accessory flexible venturi brush or bend a small hook on one end of a 20-inch- long flexible wire such as the one shown in Fig. 23. 4. Inspect and clean the burner if needed ...
-
Coleman 5110 - page 31
CAUTION A collision with the grill, as with any metal object, could cause injury . Use care when moving a port able gas grill. Moving the grill: • Move grill slowly . DO NOT run with or pull the grill behind you; it could hit you from behind causing injury . • DO NOT move the grill while it is lit or hot, or with object s on the cooking surface ...
-
Coleman 5110 - page 32
TYPE 1 CONNECTION ILLUSTRA TION Thermal Sensitive Handwheel 1-5/16" Acme Connection Nipple with Excess Flow V alve Regulator YOUR NEW GAS GRILL IS EQUIPPED WITH A TYPE 1 CONNECTION DEVICE WHICH HAS 3 SAFETY FEA TURES: (SEE TYPE 1 CONNECTION ILLUSTRA TION) 1. Proof of gas seal between the connector and the cylinder before gas flow takes place. ...
-
Coleman 5110 - page 33
Please do not send other correspondence to the address belo w. PRODUCT REGISTRA TION DEP ARTMENT PO BO X 2931 WICHIT A ,KS 67201 A TTN: DEPT 586 IMPOR T ANT! Coleman ¨ Grill W arranty Registration Car d COMPLETE THE A TT ACHED REGISTRA TION CARD AND RETURN WITHIN 10 D A YS TO RECEIVE THESE IMPORT ANT BENEFITS: CONFIRM Y OUR W ARRANTY : Y our promp ...
-
Coleman 5110 - page 34
7) Side burner (if applies) 8) Steamer/Fryer/W ar mer (if applies) 9) Side table design 10) Color of the grill (not including stainless steel) 11) Warming racks 12) Dependable igniter 13) Size of the grill (av ailable cooking square inches) 14) Integrated storage cabinet 15) Price 16) Rotisserie (if applies) 17) Other CONGRA TULA TIONS ON Y OUR NEW ...
-
Coleman 5110 - page 35
Recipes Lemongrass beef skewers with peanut dipping sauce Cooking time after marination: 4-5 minutes 2 pounds boneless sirloin For the Marinade: 3 cloves garlic, minced 2 stalks lemongrass, trimmed of tough outer layer , sliced (find in Asian market s) 2 Tb sugar 1 Tb soy sauce 3 Tb thai fish sauce (find in Asian markets) 1.5 inch thick slice fresh ...
-
Coleman 5110 - page 36
Coleman Gas Barbecue Grill Limited W arranty Castings and Burners - Limited Lifetime Electronic Ignition Components - Limited Five (5) Y ears Cooking Surfaces and Other Parts - Limited Three (3) Y ears The Coleman Company , Inc. (“Coleman”) warrants that this product will be free from defects in material and workmanship. This warranty applies t ...
Haben Sie eine Frage bezüglich Coleman 5110?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Coleman 5110 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Coleman 5110 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.