Bedienungsanleitung Black Box 1121A

36 Seiten 0.95 mb
Download

Zur Seite of 36

Summary
  • Black Box 1121A - page 1

    Models AC1120A 1121A 1122A 1123A * 16x16 and 8x8 VGA/HDTV Video Matrix Switch with Front Panel, RS232, and Optional Audio & IP Control * This user’s manual pertains to a number of Black Box 16x16 and 8x8 video matrix switches. Some models have audio switching and IP control port, and some models do not. UMA1149 Rev . A Order toll-free in the ...

  • Black Box 1121A - page 2

    ...

  • Black Box 1121A - page 3

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 1 TRADEMARKS USED IN THIS MANUAL BLACK BOX and its logo are registered trademarks of Black Box Corporation. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners. FCC and Canadian Dept of Co mmunications Radio Frequency inte ...

  • Black Box 1121A - page 4

    Model AC1120A, AC1121A, AC1122A, AC1123A 2 Table of Contents 1.0 GENERAL..................................................................................................... 4 1.1 F EATURES .................................................................................................... 4 2.0 INSTALLATION ........................................ ...

  • Black Box 1121A - page 5

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 3 3.2.2 Routing Functions .............................................................................. 17 3.2.2.1 To make a video tie: ................................................................................ 17 3.2.2.2 To make an audio tie: ......................... ...

  • Black Box 1121A - page 6

    Model AC1120A, AC1121A, AC1122A, AC1123A 4 About This Manual This user’s manual covers several variations of Black Box’s 8x8 and 16x16 VGA/HD matrix switches. Four configurations of the m atrix are discussed in this user’ manual per the ta ble below. Since this is an all-encompassing user’s m anual, portions of this guide m ay not pertain t ...

  • Black Box 1121A - page 7

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 5 2.0 Installation The matrix i s housed in a 2RU 19” wide rack mountable enclosure. Al l of I/O, control, and the power connections are on the rear of the uni t. Figure 1 – Rear panel of AC1123A showing all the connections 2.1 Input Audio & Video Connections Figure 2 ...

  • Black Box 1121A - page 8

    Model AC1120A, AC1121A, AC1122A, AC1123A 6 The audio input on the basic unit uses standard 3.5mm m ini-stereo connectors. To use these with PC audio, standard m ale-to-male audio extension cables would be required. To connect from ty pical TV sources with separate right and left connectors, 3.5mm male to 2 RCA cable s would be needed. Technical Not ...

  • Black Box 1121A - page 9

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 7 The audio outputs of the matrix are balan ced. So a + and a – are provided for each side. There is also a ground connection avail able. If you are going to connect the matrix out put to a single-ended audio device (one with RC A or phono connectors), then use the + of the ...

  • Black Box 1121A - page 10

    Model AC1120A, AC1121A, AC1122A, AC1123A 8 The main RS-232 port is on a screw term inal and the auxiliary port is on an RJ45. Caution on RJ45 Control Input Since the matrices with the IP control and those without both have an RJ45 connector next to the RS-232 scr ew terminal, it is easy to confuse their function. The functi on of the connector shou ...

  • Black Box 1121A - page 11

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 9 Figure 8 – Aux RS-232 port pinout 2.4.2 Units with IP control Models AC1121A and AC1123A are equipped wi th 10/100 base-T Ethernet connection and can be controlled via IP. They also have the primary RS-232 serial control port on the screw terminal i nput. The com mand set ...

  • Black Box 1121A - page 12

    Model AC1120A, AC1121A, AC1122A, AC1123A 10 All of the front panel switch es have built-in LEDs that h elp in the operation . The functions of fro nt panel are carefully designed for intuitiveness. W ith just a little practice, one can learn to quickly monitor and control the m atrix. 3.1.1 Viewing Audio and Video Routings or “Ties” There are t ...

  • Black Box 1121A - page 13

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 11 Press and release any output button, the b acklit LED of that bu tton will light, and if that output’s video and audi o are tied to one particular input, t hat input LED will also light. Note: If there is audio breakaway, the input LED will not be lit You can now use the ...

  • Black Box 1121A - page 14

    Model AC1120A, AC1121A, AC1122A, AC1123A 12 When you are done viewing ties, to exit you can hit ENTER. If you don’t hit any buttons, then after 8 sec the vi ew function times out and all the input and output LEDs will go out. 3.1.1.3 Viewing ties by Audio onl y Press and release the AUD and/or VID bu ttons so that the backlit LED of the AUD butto ...

  • Black Box 1121A - page 15

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 13 Press and release any Input button, the b acklit LED of that bu tton will light, and all the backlit LEDs for the ou tputs tied to it will light up solid. At this point, pressing any output buttons will be breaking or making connections. To disconnect a tie, press th e lit ...

  • Black Box 1121A - page 16

    Model AC1120A, AC1121A, AC1122A, AC1123A 14 3.1.3 Recalling Presets (routing patterns) The number of presets accessible from front panel is the same as # of inputs (however through the IP or Serial port, the unit can store and recall up to 16 presets even for an 8 input Model) Press and release the Preset button. The button will ligh t up solid. Th ...

  • Black Box 1121A - page 17

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 15 The associated input LED lights up, the matrix will tem porarily route the audio input from t he selected channel to audio output #1 and moni tor its level on the front panel. Any other outputs t ied to this selected input channel st ay connected during this adjustm ent pr ...

  • Black Box 1121A - page 18

    Model AC1120A, AC1121A, AC1122A, AC1123A 16 3.2 Control Commands (RS-232 and IP) The matrices can be cont rolled via an external control system by using RS-232. Additionally , Models AC1121A and AC1123A can be controlled t hrough an IP port. Any program capabl e of standard serial communi cation in ASCII format is capable of working with the m atri ...

  • Black Box 1121A - page 19

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 17 3.2.1 Naming Functions The matrix unit can be named. Its name can be up to 10 characters l ong. To assign or retrieve a unit nam e: Command: NU<cr> stands for Name Unit Response: xxxxxxxxxx (current name) Rename unit: ___________ No change<cr> If you hit <cr ...

  • Black Box 1121A - page 20

    Model AC1120A, AC1121A, AC1122A, AC1123A 18 Response: CAn,m<cr> CVn,m<cr> Note: If the system does not have audio, it will still accept this comm and but response will be missing audio tie line. 3.2.3 Preset Pattern Saving and Routing Functions 3.2.3.1 To recall a saved preset Video routing pattern: Command: PRx<cr> stands for Pre ...

  • Black Box 1121A - page 21

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 19 3.2.6 To Read Audio Volume Units (VU) of output #1 This comm and returns the height of hypothetical bar LED indicator having a height of 16 segments. It will return a nu mber from 0 to 16 with 10 being 0 db level. So if the output #1 is at 0 dB (900 mv p-p sinewave) it ret ...

  • Black Box 1121A - page 22

    Model AC1120A, AC1121A, AC1122A, AC1123A 20 Enter the second (00-59): Enter AM/PM (0-1): Notes : You have 16 seconds to make your selection, or the command is cancelled. To skip the current prompt without making a change, press ENTER. Invalid entry<cr> Cancelled <cr> if invalid value wa s entered. Cancelled <cr> if ESC was entered ...

  • Black Box 1121A - page 23

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 21 4 = Schedule On 5 = Schedule Off ESC = Quit Note: You have 16 seconds to m ake your selection, or the comm and is cancelled. Response: if “1”, “2” or “3” was entered Enter weekday Tim er1 hour (00-12): Hit Enter if you want to keep previous value Enter weekday ...

  • Black Box 1121A - page 24

    Model AC1120A, AC1121A, AC1122A, AC1123A 22 Matrix Comma nd Processing Port 1001 Port 23 IP Setup Serial Control IP Control RS-232 Port 3.2.12 IP Control Basics Figure 14 – Control Bl ock Diagram As shown in the figure above, the ma trix can be controlled via RS232 Serial port or through an IP (Ethernet) port if equipped. If t he unit is missing ...

  • Black Box 1121A - page 25

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 23 This is the normal response meaning that IP setting through the RS-232 port is allowed - - - - - Alternate Response - - - - - IP comma nds not enabled. Please refer to the manual This message indicates t hat IP setting through the RS-232 port is disabl ed on your unit for ...

  • Black Box 1121A - page 26

    Model AC1120A, AC1121A, AC1122A, AC1123A 24 9. To set a port number (IP port that co ntrols the Matrix): Command: SPN1000 <cr> stands for Set Port Num ber. Response: OK .................................................. if command completed successfully . Error ........................................................................... if com ...

  • Black Box 1121A - page 27

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 25 3.2.12.2 IP Configuration through port 23 If you were unable to enter the IP sett ing mode through the serial com mand, a Telnet TCP programm ing method can be used to turn on R S-232 serial mode programm ing, or even to configure the network settings directl y through por ...

  • Black Box 1121A - page 28

    Model AC1120A, AC1121A, AC1122A, AC1123A 26 7. To get the current subnet m ask: Command: <CTRL-B> GNM <CR> Response: <CTRL-B> A 255.255.255.0 <CR> 8. To set a subnet mask: Command: <CTRL-B> SNM 255.255.255.0 <CR> 9. To get a port number: Command: <CTRL-B> GPN <CR> Response: <CTRL-B> A 1001 <C ...

  • Black Box 1121A - page 29

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 27 Note on IP Settings through port 23 If you are unable to access the unit’s port 23 from your PC using the matrix’s default or last known IP address, it could be that the IP address of the matrix is not compatible on your LAN. One way around this is to connect your PC d ...

  • Black Box 1121A - page 30

    Model AC1120A, AC1121A, AC1122A, AC1123A 28 4.0 Maintenance and Troubleshooting 4.1 Maintenance The front panel CHECK button LED st arts flashing if one of the following conditions occurs: • RTC Battery Voltage is below 2.4V • +5V Supply is outsi de of normal operating range 4.5V – 5.5V • +12V Supply is outsi de of normal operating range 10 ...

  • Black Box 1121A - page 31

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 29 4.2.2 Shipping and Packaging If you need to transp ort or ship you r matrix: • Package it carefully. We recommend that y ou use the original container. • Before you ship the unit back to Black Box for repair or return, contact us to get a Return Authorizat ion (RA) num ...

  • Black Box 1121A - page 32

    Model AC1120A, AC1121A, AC1122A, AC1123A 30 Appendix 1 – Front Panel Quick Reference Guide Figure 15 – Control butt ons on the front panel Function Procedure View ties or Make ties  Hit VID and/or AUD buttons to light desired  Hit any of the INPUT or OUTPUT Butto ns  To change ties, hit any INPUT or OUTPUT then hit ENTR  Use ▲ and ...

  • Black Box 1121A - page 33

    8x8 and 16x16 VGA / HDTV Matrix Switch with Audio, RS232 & IP Control 31 Appendix 2 – Command Summary Command Function COn,m Connect Output (both A&V). n = output, m= input  Omitting ,m will show current connections  Substitute * for n to tie all outputs CVn,m Connect Video output. n = output, m= input  Omitting ,m will show curr ...

  • Black Box 1121A - page 34

    Model AC1120A, AC1121A, AC1122A, AC1123A 32 ...

  • Black Box 1121A - page 35

    ...

  • Black Box 1121A - page 36

    © Co py ri g ht 2008. Black Box Cor p oration. All ri g hts reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 ...

Produzent Black Box Kategorie TV Video Accessories

Dokumente, die wir vom Produzenten des Geräts Black Box 1121A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Black Box
- Bedienungsanleitungen 1121A
- Produktkarten Black Box
- Informationsbroschüren
- oder Energieetiketten Black Box 1121A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Black Box 1121A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Black Box 1121A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Black Box 1121A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Black Box 1121A ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Black Box 1121A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Black Box 1121A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Black Box 1121A verständlich ist.

Eine gänzliche Bedienungsanleitung von Black Box sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Black Box 1121A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Black Box 1121A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Black Box 1121A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Black Box 1121A - die uns die ersten Schritte während der Nutzung von Black Box 1121A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Black Box 1121A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Black Box 1121A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Black Box 1121A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Black Box 1121A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Black Box 1121A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)