Manual de instrucciones Porter-Cable MODEL 7310

25 de páginas 0.3 mb
Descargar

Pasar a la página of 25

Summary
  • Porter-Cable MODEL 7310 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable MODEL 7310 - page 2

    T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property ...

  • Porter-Cable MODEL 7310 - page 3

    Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry produ ...

  • Porter-Cable MODEL 7310 - page 4

    Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work are ...

  • Porter-Cable MODEL 7310 - page 5

    d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose cl ...

  • Porter-Cable MODEL 7310 - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2 . USE CLAMPS OR OTHER PRACTICAL WAY TO SECURE A ...

  • Porter-Cable MODEL 7310 - page 7

    7 NOTES ...

  • Porter-Cable MODEL 7310 - page 8

    8 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g .................... ...

  • Porter-Cable MODEL 7310 - page 9

    9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amp ...

  • Porter-Cable MODEL 7310 - page 10

    10 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for flush and bevel trimming laminated plastics, phenolics, and other similar materials having a bonding agent too hard to be trimmed with ordinary tools. The Tilt-Base model allows trimming into corners inaccessible to standard trimmers and to trim laminated surfaces jo ...

  • Porter-Cable MODEL 7310 - page 11

    11 TO AVOID PERSONAL INJURY OR DAMAGE TO FINISHED WORK ALWAYS ALLOW THE MOTOR TO COME TO A COMPLETE STOP BEFORE SETTING TRIMMER DOWN. TO INST ALL BIT DISCONNECT TOOL FROM POWER SOURCE. 1. On Models 7310 and 7319 bits may be installed with the motor unit either assembled or removed from the base. See instructions under Model 7312 for installing the ...

  • Porter-Cable MODEL 7310 - page 12

    ADJUSTING DEPTH OF CUT DISCONNECT TOOL FROM POWER SOURCE. 1. Loosen base locking screw (Fig. 3) approximately one-quarter turn. 2. Turn depth adjusting wheel (Fig. 3) clockwise, looking at top of wheel, to raise cutter reducing depth of cut or counterclockwise to lower cutter for increasing depth of cut. 3. Tighten base locking screw securely and m ...

  • Porter-Cable MODEL 7310 - page 13

    13 ASSEMBLING AND ADJUSTING BASE AND ROLLER GUIDE 1. Remove power unit from base unit (see “TO INSTALL BIT”), and install the bit. 2. The base and roller guide (A) Fig. 4, is assembled at the factory. To assemble, remove a sub-base mounting screw (A) Fig. 5 and insert alignment pin in guide base into hole (C) in bottom of trimmer sub-base. Fast ...

  • Porter-Cable MODEL 7310 - page 14

    14 5. Remove guide setting gauge from trimmer and install flush trimming bit. 6. Adjust depth of cut so that the straight portion of the bit extends below the trimmer base at least the thickness of the material to be trimmed. 7. Make a trial cut on scrap material. Readjust if necessary. BEVEL TRIMMING 1. Follow Steps 1 through 5 under FLUSH TRIMMIN ...

  • Porter-Cable MODEL 7310 - page 15

    15 be sure at least 1 / 2 " of bit shank is engaged in collet. Do not use bits that result in having less than 1 / 2 " of bit shank engaged in collet. To do so may cause poor gripping of collet resulting in loose bit and damage to work, or personal injury should the bit come out of collet. ADJUSTING TIL T 1. Loosen two tilt locking screws ...

  • Porter-Cable MODEL 7310 - page 16

    16 TO INST ALL & REMOVE BIT DISCONNECT TOOL FROM POWER SOURCE. 1 . Insert long portion of hex wrench (furnished) through spindle lock hole (see Fig. 10) so that wrench protrudes from both sides of base housing. It may be necessary to rotate spindle by hand to align hole in spindle with holes in housing. 2 . Clean and insert bit shank into colle ...

  • Porter-Cable MODEL 7310 - page 17

    17 3. DISCONNECT TOOL FROM POWER SOURCE. 4 . Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and cord will not “hang up” on any obstructions. 6. Be sure workpiece is firmly held in place. Use clamps where necessary to secure workpiece. 7. Plug in power supply cord. Be alert to ...

  • Porter-Cable MODEL 7310 - page 18

    18 UNDERSCRIBE 7320 TRIMMER ASSEMBL Y The Underscribe Trimmer Base is assembled to the Model 7301 Trimmer Motor as follows: NOTE: The 43109 Trim Bit must be installed into the Trimmer Motor before attaching the motor to the Underscribe Base. DISCONNECT TOOL FROM POWER SOURCE. 1. Clean and insert shank of bit (A) Fig. 14, into collet until end of sh ...

  • Porter-Cable MODEL 7310 - page 19

    19 bottoms. Then pull bit out approximately 1 / 8 ". 2 . Depress spindle lock (B) Fig. 14, and rotate collet nut (C) clockwise by hand until lock engages hole in motor spindle. 3 . While holding spindle lock engaged, tighten collet nut securely by turning clockwise using wrench provided. NEVER TIGHTEN COLLET WITHOUT BIT INSERTED, TO DO SO MAY ...

  • Porter-Cable MODEL 7310 - page 20

    20 If joint to TOO TIGHT (laminate will not snap into place), turn eccentric counterclockwise. 4. Repeat Steps 1 through 3 as required to achieve a good fit- up. USING THE UNDERSCRIBE TRIMMER The bottom plate of the Underscribe Trimmer has a guide lip (see Fig. 17). This guide lip is moved along an installed piece of laminate as the trimmer bit cut ...

  • Porter-Cable MODEL 7310 - page 21

    21 5. Position the underscribe trimmer onto the face frame so that the top (see Fig. 19), is against the edge of the stile. NOTE: The trimmer should be to the right of the rail, so that the cutting action will move from right to left (see Fig. 19). 6. Verify that bit is clear of foreign objects and that cord will not hang on any obstructions. 7. Gr ...

  • Porter-Cable MODEL 7310 - page 22

    22 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail t ...

  • Porter-Cable MODEL 7310 - page 23

    23 SERVICE REPLACEMENT P ARTS When servicing use only identical replacement parts. SERVICE AND REP AIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER- CABLE SERVICE STATION ...

  • Porter-Cable MODEL 7310 - page 24

    24 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable MODEL 7310 - page 25

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Fabricante Porter-Cable Categoría Laminate Trimmer

Los documentos del dispositivo Porter-Cable MODEL 7310 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Porter-Cable
- manuales de instrucciones MODEL 7310
- hojas de producto Porter-Cable
- folletos informativos
- o etiquetas energéticas Porter-Cable MODEL 7310
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Porter-Cable MODEL 7310.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Porter-Cable MODEL 7310, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Porter-Cable MODEL 7310. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Porter-Cable MODEL 7310.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Porter-Cable MODEL 7310, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Porter-Cable MODEL 7310. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Porter-Cable MODEL 7310.

El manual de instrucciones completo de Porter-Cable debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Porter-Cable MODEL 7310 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Porter-Cable MODEL 7310, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Porter-Cable MODEL 7310 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Porter-Cable MODEL 7310 - que deben facilitarnos los primeros pasos durante el uso de Porter-Cable MODEL 7310
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Porter-Cable MODEL 7310
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Porter-Cable MODEL 7310 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Porter-Cable MODEL 7310?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable MODEL 7310, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable MODEL 7310 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)