Manual de instrucciones Porter-Cable 7320

23 de páginas 0.27 mb
Descargar

Pasar a la página of 23

Summary
  • Porter-Cable 7320 - page 1

    Double Insulated Laminate T rimmers Instruction manual ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 MODEL 7310 T rimmer MODEL 7319 Tilt Base T rimmer MODEL 7312 Offset T rimmer MODEL 7320 Base Attachment For 97311 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur ...

  • Porter-Cable 7320 - page 2

    2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage. There ...

  • Porter-Cable 7320 - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry p ...

  • Porter-Cable 7320 - page 4

    4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fir e and/or serious injury . The term "power tool" in all of the warnings listed below refers to your mains-operated (cor ded) power tool or battery-operated (cordless) power tool. SA VE THESE INSTRUCTIONS 1) W ork area safety a) Keep w ...

  • Porter-Cable 7320 - page 5

    5 on. A wrench or a key left attached to a r otating part of the power tool may result in personal injury . e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress pr operly . Do not wear loose clothing or jewelry . Keep your hair , clothing and gloves away ...

  • Porter-Cable 7320 - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULA TED GRIPPING SURF ACES WHEN PERFORMING AN OPERA TION WHERE THE CUTTING TOOL MA Y CONT ACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator . 2 . USE CLAMPS OR OTHER PRACTICAL WA Y TO S ...

  • Porter-Cable 7320 - page 7

    7 MOTOR Many Porter -Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 per cent of that shown on the specification plate on the tool. Several models, however , are designed for A.C. current only . Refer to the specification plate on your tool for proper voltage and current rating ...

  • Porter-Cable 7320 - page 8

    FUNCTIONAL DESCRIPTION FOREWORD Porter -Cable Laminate T rimmers ar e designed for the flush and bevel trimming of laminated plastics, phenolics, and other similar materials that have a bonding agent too hard to be trimmed with or dinary tools. The Tilt-Base model allows trimming into corners inaccessible to standard trimmers. This model also allow ...

  • Porter-Cable 7320 - page 9

    9 CARTON CONTENTS 1. T rimmer motor 2. T rimmer base (or bases, if a kit is purchased) 3. Wr ench (or wrenches, if a kit is pur chased) OPERA TION A MODEL 7301 MOTOR UNIT All laminate trimmers in this manual use the Model 7301 Motor Unit. TO ST ART AND STOP THE MOTOR NOTE: This tool is shipped completely assembled. No assembly time or tools are r e ...

  • Porter-Cable 7320 - page 10

    1. On Models 7310 and 7319, you can install bits either with the motor unit attached or removed. NOTE: See the instructions (Model 7312) for installing the bit in the OFFSET trimmer . See instructions (Model 7320) for installing the bit in the UNDERSCRIBE trimmer . 2. Clean and insert the shank of the bit (C) Fig. 2 into the collet until the end of ...

  • Porter-Cable 7320 - page 11

    1. Loosen the base-locking screw (A) Fig. 4) approximately 1/4 turn. 2. T ur n the depth-adjusting wheel (B) Fig. 4 to reduce or incr ease the depth of cut. 3 . Tighten the base-locking screw securely . Make a test cut in scrap material to check the depth of cut. 4. Repeat steps 1 through 3 until the desired depth of cut is achieved. 11 ADJUSTING T ...

  • Porter-Cable 7320 - page 12

    12 1. Remove the power unit from the base unit (see “TO INST ALL BIT” ). 2. Install the bit. 3. The base and roller guide (A) Fig. 5 is assembled at the factory . T o install, remove a sub-base mounting scr ew (A) Fig. 6 and insert the alignment pin (in the guide base) into the hole (C) in the bottom of the trimmer sub-base. Fasten with two mou ...

  • Porter-Cable 7320 - page 13

    13 USING STRAIGHT EDGE GUIDE Y ou can use the straight edge guide (D) Fig. 5 with either bit for trimming straight edges. Attach it to the guide base and adjust similar to the other guides. Model 7319 Tilt Base T rimmer is completely attached at the factory . Y ou can remove the base from the Model 7301 motor with a base locking screw (A) Fig. 8. N ...

  • Porter-Cable 7320 - page 14

    14 DISCONNECT THE TOOL FROM THE POWER SOURCE! MODEL 7312 OFFSET TRIMMER ASSEMBL Y Y our Model 7312 Offset T rimmer was assembled at the factory . However , if you choose to attach an auxiliary base, use the following instructions: 1. Remove the collet nut and collet from the motor unit. 2. Attach the drive pulley (A) Fig. 10 to the motor spindle. T ...

  • Porter-Cable 7320 - page 15

    1. Loosen the bit in the collet (See "TO INST ALL & REMOVE THE BIT" ). 2. Place the hex wrench (A) Fig. 14 in the depth-adjusting screw (B). 3. Hold the spindle (C) Fig. 14 with your fingers. Apply light upward pressur e on the bit to maintain contact between the bit shank and the adjusting screw . T ur n the hex wrench counter -clock ...

  • Porter-Cable 7320 - page 16

    1. Allow your workpiece to overhang the base material by at least 1/8". 2. Firmly grasp the motor housing, being sure switch is in the “OFF” position. 3. Ensure that the bit is clear of foreign objects and that the cor d will not “hang up” on any obstructions. 4. Hold the workpiece firmly in place. Use clamps when necessary . 5. Plug i ...

  • Porter-Cable 7320 - page 17

    17 TYPICAL APPLICA TIONS TRIMMING 3 / 4 " IN-AND-OUT TRIMMING SCRIBING OF VERTICAL BACKSPLASH OF INST ALLED CORNER BACKSPLASH TO WALL APPLICA TION – T rimming front edge of 3 / 4 " vertical backsplash. This is an opera- tion standard trimmers with round or square bases are unable to do without the use of a special bit. Self-piloted bit ...

  • Porter-Cable 7320 - page 18

    18 T rims up to vertical surfaces. T rims odd angled corners less than or greater than 90°. ADJUSTING THE BIT EXPOSURE DISCONNECT THE TOOL FROM THE POWER SOURCE. 1. Loosen the base locking screw (E) Fig. 20 approximately 1/4 turn. 2. T urn the depth-adjusting wheel (D) Fig. 20 counter -clockwise (looking at top of wheel) to lower the bit until it ...

  • Porter-Cable 7320 - page 19

    19 The “butt” joint is commonly used in the construction of face frames. T o install a laminate covering on a face frame: Always wear safety glasses while operating a laminate trimmer . A T rimmer Base B Sub-Base C Installed laminate D Guide Lip E Bit F Laminate 1. Cut the pieces of laminate covering to rough size. Apply contact cement to the f ...

  • Porter-Cable 7320 - page 20

    20 6. V erify that the bit is clear of foreign objects and that the cor d will not get caught on any obstructions. 7. Grasp the motor firmly to resist starting torque and move the switch button to the "ON" position. 8. Allow the motor to reach full-speed. Feed the trimmer from right to left with a smooth steady motion. NOTE: The tapered e ...

  • Porter-Cable 7320 - page 21

    21 A complete line of accessories is available from your Porter -Cable • Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Porter -Cable Authorized Service Stations. Please visit our W eb Site www .porter -cable. com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Porter ...

  • Porter-Cable 7320 - page 22

    22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, pr oves to be defective in workmanship or materi ...

  • Porter-Cable 7320 - page 23

    ® 4825 Highway 45 North Jackson, TN 38305 1-800-223-7278 www .porter -cable.com ...

Fabricante Porter-Cable Categoría Laminate Trimmer

Los documentos del dispositivo Porter-Cable 7320 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Porter-Cable
- manuales de instrucciones 7320
- hojas de producto Porter-Cable
- folletos informativos
- o etiquetas energéticas Porter-Cable 7320
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Porter-Cable 7320.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Porter-Cable 7320, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Porter-Cable 7320. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Porter-Cable 7320.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Porter-Cable 7320, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Porter-Cable 7320. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Porter-Cable 7320.

El manual de instrucciones completo de Porter-Cable debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Porter-Cable 7320 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Porter-Cable 7320, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Porter-Cable 7320 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Porter-Cable 7320 - que deben facilitarnos los primeros pasos durante el uso de Porter-Cable 7320
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Porter-Cable 7320
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Porter-Cable 7320 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Porter-Cable 7320?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 7320, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 7320 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)