Manual de instrucciones Thermador CD365

28 de páginas 2.76 mb
Descargar

Pasar a la página of 28

Summary
  • Thermador CD365 - page 1

    Car e & Use Man ual and Installation Instructions for Thermador ® Glass Ceramic Gas and Glass Ceramic Dual Gas & Electric Cooktops Models: CGX304 / CGX365 / CGX456 CD365 / CD456 ...

  • Thermador CD365 - page 2

    A Special Message to Our Customers, Thank you for buying a Thermador ® cooktop. We hope that the informa- tion in this manual helps you easily operate and care for your cooktop for years of satisfaction. Please contact us if you have any questions or comments. Sincerely, Thermador Test Kitchen Consumer Scientists Packaged with Cooktop Care and Use ...

  • Thermador CD365 - page 3

    PROPANE GAS INSTALLATION The cooktop is ready for use with natural gas. It may be converted for use with propane gas using the Burner Propane Conversion Kit, Model NLPKIT5, Part Number 35-00-622. A qualified service techhnican or installer can convert the cooktop. Be sure the unit being installed is correct for the type of gas being used. Refer to ...

  • Thermador CD365 - page 4

    SAFETY PRA CTICES T O A V OID PERSONAL INJUR Y IMPOR T ANT SAFETY INSTR UCTIONS READ ALL INSTRUCTIONS BEFORE USING YOUR COOKTOP PAGE 2 • Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally. • Do not cook on a cooktop in which the glass top has broken. I ...

  • Thermador CD365 - page 5

    IMPOR T ANT SAFETY INSTR UCTIONS PAGE 3 • The cooktop is factory assembled for natural gas . I t should be correctly adjusted by a qualified service person or installer for the type of gas with which it is used. (See Page 1 for propane gas.) • For personal safety, wear proper apparel. Loose fitting garments or hanging sleeves should never be wo ...

  • Thermador CD365 - page 6

    ELECTRICAL REQUIREMENTS AND GROUNDING INSTR UCTIONS See Installation Instructions for electrical require- ments and grounding instructions, Page 24. FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD PLUG. If the electrical outlet you intend to use ...

  • Thermador CD365 - page 7

    MODEL and P AR TS IDENTIFICA TION 1. 1300 to 9100 BTU/HR Burner & Control Knob 2. 1650 to 11,000 BTU/HR Burner & Control Knob 3. 1650 to 11,000 BTU/HR Burner & Control Knob 4. 1300 to 9100 BTU/HR Burner & Control Knob 5. Dual-Circuit Element: Small 6"–1000 Watt, Large 9" – 2200 Watt Element & Control Knob 6. Dual-C ...

  • Thermador CD365 - page 8

    MODEL and P AR TS IDENTIFICA TION Models CGX365U Models CGX456U Page 6 Model CGX304U ...

  • Thermador CD365 - page 9

    1. 1300 to 9100 BTU/HR Burner & Control Knob 2. 1650 to 11,000 BTU/HR Burner & Control Knob 3. ExtraLow® 365 to 11,000 BTU/ HR Burner & Control Knob 4. ExtraLow® 300 to 9100 BTU/HR Burner & Control Knob 5. 1300 to 9100 BTU/HR Burner & Control Knob 6. 1650 to 11,000 BTU/HR Burner & Control Knob 7. "ON" Light 8. Gr ...

  • Thermador CD365 - page 10

    ELECTRIC COOKT OP OPERA TION ELEMENTS When either element is turned on the "ON" signal light turns red; when both elements are turned off, the “ON” signal light goes out. Page 8 BEFORE USING THE COOKTOP FOR THE FIRST TIME: • Remove all packing materials and literature from the cooktop surface. Read all safety precautions and care &a ...

  • Thermador CD365 - page 11

    ELECTRIC COOKT OP OPERA TION Page 9 SIGNAL LIGHTS Element “ ON ” Signal Light The element “ON” signal light glows whenever any element is turned on. The light remains lit until all of the elements are turned off. The “ON” light is located on the right side and below the control knobs. HOT SURFACE INDICATOR LIGHTS Whenever a cooking surf ...

  • Thermador CD365 - page 12

    GAS CONTROL KNOB SETTINGS EXTRALOW ® (CGX Models Only) STANDARD BURNER (All Models) GAS COOKT OP OPERA TION Page 10 FOR THE BEST RESULTS • Temperature control will be more accurate if a lid is used. • Bring food to a rolling boil; stir well to be sure all the food is boiling; cover and reduce the heat to just below LO . • Check periodically ...

  • Thermador CD365 - page 13

    GAS COOKT OP OPERA TION BURNER BASE Igniter (Underside) COOKTOP PARTS FOR PROPER COMBUSTION DO NOT USE THE COOKTOP WITHOUT THE BURNER GRATES IN PLACE . Each five finger grate is porcelain enameled cast iron and has five (5) prongs. These prongs fit into the five (5) indentations on the burner plate below. Prongs Indentations B Notch C Page 11 BURNE ...

  • Thermador CD365 - page 14

    Flame Too Large for Pan Size Balanced Pan Unbalanced Pan Use Lids that fit Properly CHARACTERISTICS OF A GOOD PAN The choice of pans directly affects the cooking speed and uniformity. For best results select pans with the following features: FLAT BASES - Check flatness of pan with a straight edge. When pan is hot, the base (pan bottom) should rest ...

  • Thermador CD365 - page 15

    Woks and Speciality Pans Use only a flat bottom wok on electric heating elements. A round bottom wok can be used on the burners with a support ring. The round bottom wok is unstable without the ring. Check that the ring does not restrict air to the burners causing a yellow flame. See Custom Accessories AWOKRING below. Specialty pans such as woks, l ...

  • Thermador CD365 - page 16

    Page 14 ELECTRIC COOKING CHAR T FOOD ST AR T COOKING CONTINUE COOKING BREADS French T oast, Pancak es, 5 to 6 3 to 4 Grilled Sandwiches CEREALS H1 3-1/2 to 5 Cornmeal, Grits, Oatmeal CHOCOLA TE LO EGGS Hl LO Cook ed in Shell Fried, Scrambled 5 to 6 2 to 3 MEA T , FISH, POUL TR Y Bacon, Sausage Patties 5 to 6 3 to 4 Braising: Swiss Steak, 5 to 6 LO ...

  • Thermador CD365 - page 17

    Page 15 F ood Start Cooking Continue Cooking or Continue Cooking Standard Burners Extra Lo w ® , Burners (CGX models only) BREADS Med. - preheat skillet Med. Lo to Med. Use standard French T oast, Pancak es, cook burner setting Grilled Sandwiches CEREALS HI - cov er , bring water Med. Lo to Med.- I to XLO ® - to hold, Cornmeal, Grits, to a boil, ...

  • Thermador CD365 - page 18

    Use Daily How to Use Razor Blade Scraper Page 16 CLEAN CARE TECHNIQUES (FOR MOST SOILS) 1. Clean the surface when it is completely cool, with the exception of spills containing milk, dry sugar, sugar syrup, or tomato described in the Special Care Techniques on the following page. These must be removed IMMEDIATELY. CAUTION: DO NOT use any kind of cl ...

  • Thermador CD365 - page 19

    GLASS CERAMIC COOKT OP CLEANING GUIDE CD365U Model Sho wn SPECIAL CARE TECHNIQUES TYPE OF SOIL POSSIBLE SOLUTION Page 17 Failure to remove these soils immediatly can permanently damage the surface. • Remove pan and turn off the element. • Angle the scraper slightly, using care not to gouge or scratch the glass. Push soil off the heated area. ? ...

  • Thermador CD365 - page 20

    DU AL and ALL GAS COOKT OP CLEANING GUIDE The entire Cooktop can be saf ely cleaned by wiping with clean warm water and a clean sponge , then dr ying. If stubborn soil remains, follow the r ecommended cleaning methods below . • Do not clean any part of the cooktop surface when an y element or burner is on. • Alwa ys use the mildest cleaner that ...

  • Thermador CD365 - page 21

    E Stainless Alwa ys wipe or rub with grain. Clean with a soap y sponge; rinse and dr y . Or wipe with Steel Fantastic ® or Form ula 409 ® spra yed onto a pa per towel. Polish with Re ver e W are ® T rim Frame Metal P olish or Stainless Steel Magic ® and a soft cloth. Remove water spots with a cloth dampened with white vinegar . F Cooktop Seal T ...

  • Thermador CD365 - page 22

    IMPORTANT SAFETY INSTRUCTIONS • Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. • The appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70-1990. (In Canada, installation ...

  • Thermador CD365 - page 23

    CABINET CONSIDERA TIONS AND COUNTER T OP CUT OUT Dimension requirements in Figs. 1 & 2 are for combustible surfaces. When the surface is protected by a material listed by UL as a Floor Protector and Wall Shield (UL Cat. DFCV) covered with not less than No. 28 MSG sheet metal, 0.015 inch stainless steel, 0.024 inch aluminum or copper, it is cons ...

  • Thermador CD365 - page 24

    CABINET CONSI DERA TIONS AND COUNT E R TOP CUT OUT 1. INSTALLING THE COOKTOP IN NORMAL COUNTERTOPS (For solid surface cooktop, see Section 2, below) A. Instructions are based on Standard American cabinets 36" high x 24" deep with a 25" countertop. B. Provide approximately a 10 square inch opening in the toe kick area or other cabinet ...

  • Thermador CD365 - page 25

    Connect the gas supply line to the unit pressure regulator using a l/2" flex gas line connector between wall shut-off valve and pressure regulator. Secure regulator to cooktop gas inlet using approved Teflon tape. Turn to hand tighten plus 1/4 turn, not exceeding 1 turn for alignment. Turn on gas at shut-off valve and check supply line connect ...

  • Thermador CD365 - page 26

    4A. CONNECT ELECTRICAL SUPPLY – CGX MODELS Before connecting the 5-foot supply cord to wall receptacle make certain that gas shut-off valve is in the “OFF” position. WARNING: Before turning on the power, be sure that all controls on the cooktop are turned "OFF" 4B. CONNECT ELECTRICAL SUPPLY – CD MODELS 1. Attach flexible conduit t ...

  • Thermador CD365 - page 27

    Full One Year Warranty Covers one year from the date of installation or date of occupancy for a new previously unoccupied dwelling. Save your dated receipt or other evidence of the installation/occupancy date. Thermador ® Will Pay For: All repair labor and replacement parts found to be defective due to materials and workmanship. Service must be pr ...

  • Thermador CD365 - page 28

    5551 McFadden Avenue, Huntington Beach, CA 92649 • 800/735-4328 ECO 14028 • 20-04-228B • © BSH Home Appliances Corp. • Litho U. S. A. 5/01 BEFORE CALLING FOR SERVICE If the elements do not heat or if the indicator "on" light does not glow, check the power source to see if a fuse has blown or if the circuit breaker has tripped. HO ...

Fabricante Thermador Categoría Cooktop

Los documentos del dispositivo Thermador CD365 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Thermador
- manuales de instrucciones CD365
- hojas de producto Thermador
- folletos informativos
- o etiquetas energéticas Thermador CD365
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Thermador CD365.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Thermador CD365, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Thermador CD365. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Thermador CD365.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Thermador CD365, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Thermador CD365. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Thermador CD365.

El manual de instrucciones completo de Thermador debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Thermador CD365 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Thermador CD365, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Thermador CD365 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Thermador CD365 - que deben facilitarnos los primeros pasos durante el uso de Thermador CD365
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Thermador CD365
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Thermador CD365 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Thermador CD365?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Thermador CD365, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Thermador CD365 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)