Français dropdown-ico

Manuel d’utilisation Chamberlain 3265 1/2 HP

36 pages 2.91 mb
Télécharger

Aller à la page of 36

Summary
  • Chamberlain 3265 1/2 HP - page 1

    The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Model 3265 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the ...

  • Chamberlain 3265 1/2 HP - page 2

    2 Introduction 2-5 Safety symbol and signal word review . . . . . . . . . . . . . . . .2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . .3 T ools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Carton invento ...

  • Chamberlain 3265 1/2 HP - page 3

    3 T o prevent damage to garage door and opener: • AL WA YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJURY or DEA TH: • AL WA YS call a trained door systems technician if garage door binds, sticks or is out of bal ...

  • Chamberlain 3265 1/2 HP - page 4

    FI N ISHED CEILI N G S u pport b racket & fastening hard w are is re qu ired. See page 12. Slack in chain tension is normal w hen garage door is closed. Safety Re v ersing Sensor Header W all Access Door Safety Re v ersing Sensor Gap b et w een floor and b ottom of door m u st not exceed 1/4" (6 mm). W all- mo u nted Door Control Motor Uni ...

  • Chamberlain 3265 1/2 HP - page 5

    5 Y our garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below . Carton Inventor y Straight Door Arm Sectio ...

  • Chamberlain 3265 1/2 HP - page 6

    6 ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position rail at a 45˚ angle to opener so one hole in rail and motor unit line up. • Thread one of the washered bolts part way i ...

  • Chamberlain 3265 1/2 HP - page 7

    7 Lock W asher T o Tighten O u ter Nu t Inner Nu t T rolley T o Tighten Inner Nu t O u ter Nu t INST ALLA TION ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown (Figure 1). • When the chain is approxima ...

  • Chamberlain 3265 1/2 HP - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket withi ...

  • Chamberlain 3265 1/2 HP - page 9

    9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HEA ...

  • Chamberlain 3265 1/2 HP - page 10

    10 Cle v is Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you will need help. Have someone hold the opener securely on a temporary support to a ...

  • Chamberlain 3265 1/2 HP - page 11

    11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to- rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail ...

  • Chamberlain 3265 1/2 HP - page 12

    Meas u re Distance Lag Scre w s 5/16"-1 8 x1-7/ 8 " Str u ct u ral S u pports Bracket ( N ot Pro v ided) Lag Scre w s 5/16"-1 8 x1-7/ 8 " ( N ot Pro v ided) Bolt 5/16"-1 8 x7/ 8 " Lock W asher 5/16" Nu t 5/16"-1 8 FINISHED CEILING Hidden S u pport Bolt 5/16"-1 8 x7/ 8 " Lock W asher 5/16" Nu t ...

  • Chamberlain 3265 1/2 HP - page 13

    13 T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJURY or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a minimu ...

  • Chamberlain 3265 1/2 HP - page 14

    14 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only . The light will turn ON and r ...

  • Chamberlain 3265 1/2 HP - page 15

    15 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet you have, contac ...

  • Chamberlain 3265 1/2 HP - page 16

    16 In v isi b le Light Beam Protection Area Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage ...

  • Chamberlain 3265 1/2 HP - page 17

    17 DOOR TRA CK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door T rack FLOOR MOUNT (RIGHT SIDE) W ALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W al l (Provided with Extension Bracket) (Provided with Extension Bracket) Fi g ure 1 Fi g ure 2 Fi g ure 3 Fi g ure 4 W ALL MO ...

  • Chamberlain 3265 1/2 HP - page 18

    In v isi b le Light Beam Protection Area Safety Re v ersing Sensor Connect W ire to Opener Q u ick-Connect T erminals Bell W ire Bell W ire Finished Ceilin g Q u ick-Connect T erminals 3. Insert into appropriate terminals 1. Strip w ire 7/16" (1 1 mm) 2. T w ist like colored w ires together Red Grey W hite 7/16" (1 1 mm) Safety Re v ersin ...

  • Chamberlain 3265 1/2 HP - page 19

    19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following p ...

  • Chamberlain 3265 1/2 HP - page 20

    20 Header W all V ertical Centerline of Garage Door Finished Ceilin g Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 S u pport For a door w ith no exposed framing, or for the optional installation, u se lag scre w s 5/16"x1-1/2" ( N ot Pro v ided) to fasten door b racket. MET AL DOOR T op of Door (Inside Garage) Door B ...

  • Chamberlain 3265 1/2 HP - page 21

    21 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...

  • Chamberlain 3265 1/2 HP - page 22

    22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adj ...

  • Chamberlain 3265 1/2 HP - page 23

    23 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev ...

  • Chamberlain 3265 1/2 HP - page 24

    ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather ...

  • Chamberlain 3265 1/2 HP - page 25

    Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...

  • Chamberlain 3265 1/2 HP - page 26

    OPERA TION 26 T o reduce the risk of SEVERE INJUR Y or DEA TH: Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and on ...

  • Chamberlain 3265 1/2 HP - page 27

    T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically . Pull the emergency release handle down and back (toward the ...

  • Chamberlain 3265 1/2 HP - page 28

    CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re- adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse te ...

  • Chamberlain 3265 1/2 HP - page 29

    29 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins ...

  • Chamberlain 3265 1/2 HP - page 30

    Bell W ire Safety Re v ersing Sensor Diagnostics Located On Motor Unit LED or Diagnostic LED “Learn” B u tton 30 Installed Safety Re v ersing Sensor Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Co ...

  • Chamberlain 3265 1/2 HP - page 31

    *3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er ...

  • Chamberlain 3265 1/2 HP - page 32

    L O C K LIG H T 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control (al ...

  • Chamberlain 3265 1/2 HP - page 33

    1 3 4 5 6 2 33 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail 5 41D3484 Full chain assembly 6 83A1 1-2 Rail grease 7 10 11 5 N O TIC E U P C E I L I N G M O U N T O N L Y 8 6 1 4 3 2 LO C K L IG H T 9 12 Installation ...

  • Chamberlain 3265 1/2 HP - page 34

    Motor Unit Assembly Parts 34 2 10 8 13 14 15 5 19 3 9 4 16 12 7 18 11 17 6 6 7 D N UP Bro w n W ire (Do w n) Contact LIMIT SWITCH ASSEMBL Y Grey W ire Y ello w W ire (Up) Contact Center Limit Contact Dri v e Gear 1 KEY P ART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer , thrust washe ...

  • Chamberlain 3265 1/2 HP - page 35

    35 L O C K L I G H T ACCESSORIES 374LM 370LM 395LM 170 8 LM 41A52 8 1 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.4 m) Complete Rail: T o allow an 8 foot (2.4 m) door to open fully . Remote Light Control: Enables homeowner to ...

  • Chamberlain 3265 1/2 HP - page 36

    © 2007, The Chamberlain Group, Inc. 1 14A3044F All Rights Reserved LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1- 8 00-52 8 -9131 www .liftmaster .com For professional installation, parts and service, conta ...

Fabricant Chamberlain Catégorie Garage Door Opener

Les documents que nous recevons du fabricant de l'appareilChamberlain 3265 1/2 HP peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Chamberlain
- manuels d’utilisations 3265 1/2 HP
- fiches produit Chamberlain
- dépliants
- ou étiquettes-énergie Chamberlain 3265 1/2 HP
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Chamberlain 3265 1/2 HP.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Chamberlain 3265 1/2 HP, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Chamberlain 3265 1/2 HP. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Chamberlain 3265 1/2 HP.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Chamberlain 3265 1/2 HP, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Chamberlain 3265 1/2 HP par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Chamberlain 3265 1/2 HP.

Le manuel d’utilisation complet Chamberlain, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Chamberlain 3265 1/2 HP - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Chamberlain 3265 1/2 HP, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lChamberlain 3265 1/2 HP qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Chamberlain 3265 1/2 HP - qui devraient nous aider dans les premières étapes lors de l'utilisation Chamberlain 3265 1/2 HP
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Chamberlain 3265 1/2 HP
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Chamberlain 3265 1/2 HP dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Chamberlain 3265 1/2 HP?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Chamberlain 3265 1/2 HP, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain 3265 1/2 HP il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)