Français dropdown-ico

Manuel d’utilisation Alpine PXI-H990

116 pages 6.32 mb
Télécharger

Aller à la page of 116

Summary
  • Alpine PXI-H990 - page 1

    PXI-H990 PXI-H990 OWNER'S MANUAL R Sankei Kikaku Co ., Ltd. 1-13-38, Hinodai, Hino , T okyo , Japan ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagaw a-ku, T okyo 141-0031, J apan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, T orrance, California 90501, U .S.A. Phone 1-800-ALPINE-1 (1-800-257-4631 ...

  • Alpine PXI-H990 - page 2

    ...

  • Alpine PXI-H990 - page 3

    ENGLISH R PXI-H990 Multimedia Manager™ • OWNER'S MANUAL Please read before using this equipment. ...

  • Alpine PXI-H990 - page 4

    ...

  • Alpine PXI-H990 - page 5

    1 - EN Contents W ARNING W ARNING ............................................................................................................................... 3 CA UTION ................................................................................................................................ 4 PRECA UTIONS ................................. ...

  • Alpine PXI-H990 - page 6

    2 - EN Contents Using the m ulti-channel function Adjustment procedure for multi-channel function ................................................................. 52 Speaker setup (Dolby SP) ....................................................................................................... 53 Adjusting the speaker le vels (OUTPUT LEVEL) ...... ...

  • Alpine PXI-H990 - page 7

    3 - EN W ARNING W ARNING This symbol means important instructions. Failure to heed them can result in serious injury or death. DO NOT OPERA TE ANY FUNCTION THA T T AKES YOUR A TTENTION AWA Y FROM SAFEL Y DRIVING YOUR VEHICLE. Any function that requir es y our prolonged attention should only be performed after coming to a complete stop. Always stop ...

  • Alpine PXI-H990 - page 8

    4 - EN W ARNING CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. HAL T USE IMMEDIA TEL Y IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing. PRE ...

  • Alpine PXI-H990 - page 9

    5 - EN Basic Operation Operating the PXI-H990 The PXI-H990 is operated from the head unit with which it is used. These operating instructions describe operation with the head unit; both from the unit itself and from the remote control unit. • The operation for the PXI-H990 is perf ormed from the head unit setup operation. See the reference page i ...

  • Alpine PXI-H990 - page 10

    6 - EN Basic Operation Using This Manual The PXI-H990 is operated from the head unit with which it is used. These operating instructions describe operation from both the D VI-9990 head unit and from the R UE-4196 remote control unit included with the head unit. When operating the main unit with the remote control supplied with the head unit, change ...

  • Alpine PXI-H990 - page 11

    7 - EN 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick T urning the po wer on and off This unit does not hav e a power switch. The head unit to which the unit is connected, controls its power . In order to protect the speakers when the power is f irst switched on or when the head unit is reset, no sound is produced until sys ...

  • Alpine PXI-H990 - page 12

    8 - EN Basic Operation 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ SP SETUP [Speaker Setup] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ SP SELECT [Speaker Select] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ SYSTEM SEL [System Select] ” , then pre ...

  • Alpine PXI-H990 - page 13

    9 - EN 7 Press 1 ( ) or 5 ( ) , select the system, then press 2 (ENT) . * 1 There is no OFF setting. * 2 It is not possible to turn both “ MID ” and “ WF ” off. If one is set to “ OFF ” , the other cannot be set to “ OFF ” . • Do not connect the tweeter (TW) to the channel without “ TW ” indicated in the table above. If connec ...

  • Alpine PXI-H990 - page 14

    10 - EN Basic Operation 10 Press 1 ( ) or 5 ( ) , select “ OFF ” , then press 2 (ENT) . Repeat steps 9 and 10 and s witch off all unconnected speakers . 11 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Press 6 (R TN) or RETURN on the remote control in the setting mode to return to the previous item. Sup ...

  • Alpine PXI-H990 - page 15

    11 - EN TITLE Setting the speakers (SP SELECT) Description The operations performed with the remote control unit in step 1 can also be performed by pressing MENU (SETUP) for at least 3 seconds , moving the joystic k up or down to select “ AP SETUP ” , then pressing the jo ystick. Related page Supplementary information This page includes supplem ...

  • Alpine PXI-H990 - page 16

    Automatic Adjustments 12 - EN Preparations for automatic adjustments The PXI-H990 is equipped with two automatic adjustment functions: “Road Equalizer” and “ Automated Time Correction”. The preparations described belo w must be made in order to perform these automatic adjustments. After making these preparations, refer to “ Automatic adju ...

  • Alpine PXI-H990 - page 17

    13 - EN 3 Connect the included microphone to the PXI-H990. Ref er to the Installation manual. • When combined with a separately sold monitor that is Road EQ compatible and the Road Equalizer function are used, the separately sold monitor ’ s built-in microphone can be used. • When connecting two PXI-H990 units, connect the microphone to both ...

  • Alpine PXI-H990 - page 18

    Automatic Adjustments 14 - EN Hints on using the Road Equalizer function The Road Equalizer compensates for constantly changing noise, so always keep the micr ophones connected. The follo wing three places are recommended to place the microphones. Also, when combining with the separately sold monitor , the built-in microphone can be used. A Ceiling ...

  • Alpine PXI-H990 - page 19

    15 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick Using the Road Equalizer function Road Equalizer (REAL-TIME OPTIMIZED AD APTIVE DRIVING EQU ALIZER) is a function that automatically adjusts the equalizer settings during dri ving accor ding to the amount of road noise. T o use Road Equalizer, f irst connect the ...

  • Alpine PXI-H990 - page 20

    Automatic Adjustments 16 - EN 1 Press and hold F • SETUP for at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MOBILE.S.MGR [Mobile Sound Manager] ” , then press 2 (ENT) . ...

  • Alpine PXI-H990 - page 21

    17 - EN A Selecting the Micr ophone 1) In the Road Equalizer mode, press 1 ( ) or 5 ( ) , select “ MIC SELECT [Microphone Select] ” , then press 2 (ENT) . 2) Press 1 ( ) or 5 ( ) , select the microphone, then press 2 (ENT) . EXTERNAL MIC [External Microphone]: Set this when using the microphone included with the PXI-H990. MONIT OR MIC [Monitor ...

  • Alpine PXI-H990 - page 22

    Automatic Adjustments 18 - EN 1) In the Road Equalizer mode, press 1 ( ) or 5 ( ) , select “ R.EQ SETUP [Auto Road EQ Setup] ” , then press 2 (ENT) . 2) Press 2 (ENT) . Measuring begins after a 10 second count- down, so lea v e the car and close the door within 10 seconds. Measuring is canceled if 2 (ENT) is pressed during measuring or dur ing ...

  • Alpine PXI-H990 - page 23

    19 - EN 1) In the Road Equalizer mode, press 1 ( ) or 5 ( ) , select “ Road EQ ON/OFF ” . 2) When OFF , press 1 ( ) after pressing 2 (ENT) to s witch ON. T o switch from ON to OFF , press 5 ( ) after pressing 2 (ENT) . Select “ OFF ” if you do not want to use the Road Equalizer function. • Press 6 (R TN) or RETURN on the remote control in ...

  • Alpine PXI-H990 - page 24

    Automatic Adjustments 20 - EN 1) In the Road Equalizer mode, press 1 ( ) or 5 ( ) , select “ MODE SELECT ” , then press 2 (ENT) . 2) Press 1 ( ) or 5 ( ) , select the desired mode, then press 2 (ENT) . MODE1 [Mode1]: Low compensation mode. Suit- able f or a quiet car . MODE2 [Mode2]: Higher compensation mode. MODE3 [Mode3]: Highest compensation ...

  • Alpine PXI-H990 - page 25

    21 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick Performing time correction automatically (A utomated Time Correction) Due to the particular conditions inside the vehicle, there is a major dif ference between the distances of the var ious speakers and the listening position. This function uses the included meas ...

  • Alpine PXI-H990 - page 26

    Automatic Adjustments 22 - EN 4 Press and hold F • SETUP for at least 3 seconds. 5 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . Perf orming time correction automatically (A utomated Time Correction) (continued) ...

  • Alpine PXI-H990 - page 27

    23 - EN 7 Press 1 ( ) or 5 ( ) , select “ MOBILE.S.MGR [Mobile Sound Manager] ” , then press 2 (ENT) . 8 Press 1 ( ) or 5 ( ) , select “ TCR [Time Correction] ” , then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select “ AUT O TCR [Auto Time Correction] ” , then press 2 (ENT) . • Check that “ TCR ” is set to “ ON ” . If it is set ...

  • Alpine PXI-H990 - page 28

    Automatic Adjustments 24 - EN 11 When the system reset is completed, return to the car and check that the setting v alue of the Automated Time Correction is reflected. If the setting v alue is not changed, the microphone ma y not receive sound, the speaker ma y be damaged, the connection and wiring may be a malfunction. T o store the settings, ref ...

  • Alpine PXI-H990 - page 29

    25 - EN TITLE Using the Road Equalizer function P erforming time correction automati- cally (Automated Time Correction) Description Connect both microphones if two PXI-H990s are connected. If the microphone does not pick up the sound or the speakers are not w or king or are connected or wired improperly , the automatic adjustments are not performed ...

  • Alpine PXI-H990 - page 30

    26 - EN Settings/Adjustments P erf orming time correction manuall y (Time Correction) Though suff icient correction can be achieved with the “ Automated T ime Correction” automatic adjustments, it is also possible for the user to calculate the correction values and mak e the adjustments manually . This manual adjustment requires suff icient kno ...

  • Alpine PXI-H990 - page 31

    27 - EN 4 Divide the distances calculated f or the different speak ers by the speed of sound (343 m/s temperature 20 ° C). This value is the time correction v alue f or the different speakers . • The speed of sound fluctuates according to the temperature. The accurate speed of sound can be achie ved with the formula shown belo w . Speed of sound ...

  • Alpine PXI-H990 - page 32

    28 - EN Settings/Adjustments 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick 5 Press and hold F • SETUP f or at least 3 seconds. 6 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 7 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . Perf orming time ...

  • Alpine PXI-H990 - page 33

    29 - EN Continued 8 Press 1 ( ) or 5 ( ) , select “ MOBILE.S .MGR [Mobile Sound Manager] ” , then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select “ TCR [Time Correction] ” , then press 2 (ENT) . 10 Press 1 ( ) or 5 ( ) , select “ TCR ON/OFF [Time Correction ON/OFF] ” . 11 When OFF , press 1 ( ) after pressing 2 (ENT) to s witch TCR ON [ ...

  • Alpine PXI-H990 - page 34

    30 - EN Settings/Adjustments 13 Press 1 ( ) or 5 ( ) , select “ L or R ” or “ L+R ” , then press 2 (ENT) . L or R: Different adjustment v alues can be set for the left and right channels . L+R: Sets the same adjustment v alues for the left and right channels. When “ L+R ” is selected. 1) Press 1 ( ) or 5 ( ) , select either the Lch or R ...

  • Alpine PXI-H990 - page 35

    31 - EN 16 Press 1 ( ) or 5 ( ) , select “ ADJUST [Adjust] ” , then press 2 (ENT) . 17 Press 2 (ENT) , and press 1 ( ) or 5 ( ) , adjust time correction (0.00~20.00ms, 0.05ms step), then press 6 (RTN) . 18 T o adjust another channel, repeat steps 14 to 17. 19 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. ? ...

  • Alpine PXI-H990 - page 36

    32 - EN Settings/Adjustments 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick Equalizer adjustments The PXI-H990 is equipped with a graphic equalizer and parametric equalizer . Y ou can set the Equalizer to whatev er values you want. Graphic equalizer The lev el of the front, rear and center channels can be adjusted ...

  • Alpine PXI-H990 - page 37

    33 - EN 1 Check that the head unit def eat mode is off. 2 Press and hold F • SETUP for at least 3 seconds. 3 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ MOBILE.S.MGR [Mobile Sound Manager] ...

  • Alpine PXI-H990 - page 38

    34 - EN Settings/Adjustments 8 Press 1 ( ) or 5 ( ) , select the Equalizer type, then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select “ CH MODE [Channel Mode] ” , then press 2 (ENT) . 10 Press 1 ( ) or 5 ( ) , select “ L or R ” or “ L+R ” , then press 2 (ENT) . L or R: Different adjustment v alues can be set for the left and right chann ...

  • Alpine PXI-H990 - page 39

    35 - EN 11 Press 1 ( ) or 5 ( ) , select “ CH SELECT [Channel Select] ” , then press 2 (ENT) . 12 Press 1 ( ) or 5 ( ) , select the desired channel, then press 2 (ENT) . The channels that can be selected depend on the system settings (page 9). 13 Press 1 ( ) or 5 ( ) , select “ BAND [Band] ” , then press 2 (ENT) . 14 Press 1 ( ) or 5 ( ) , ...

  • Alpine PXI-H990 - page 40

    36 - EN Settings/Adjustments 15 Press 1 ( ) or 5 ( ) , select “ ADJUST [Adjust] ” , then press 2 (ENT) . 16 Press 2 (ENT) , and press 1 ( ) or 5 ( ) , adjust the lev el ( ± 9 dB, in steps of 0.5 dB), then press 6 (RTN) . 17 T o adjust another frequency band, repeat steps 13 to 16. 18 T o adjust other channels, repeat steps 11 to 17. 19 Once th ...

  • Alpine PXI-H990 - page 41

    37 - EN 11 Press 1 ( ) or 5 ( ) , select “ CH SELECT [Channel Select] ” , then press 2 (ENT) . 12 Press 1 ( ) or 5 ( ) , select the desired channel, then press 2 (ENT). The channels that can be selected depend on the system settings (page 9). 13 Press 1 ( ) or 5 ( ) , select “ BAND [Band] ” , then press 2 (ENT) . 14 Press 1 ( ) or 5 ( ) , s ...

  • Alpine PXI-H990 - page 42

    38 - EN Settings/Adjustments 16 Press 1 ( ) or 5 ( ) , select the mode “ FREQ [F requency] ” , then press 2 (ENT) . 17 Press 1 ( ) or 5 ( ) , select the frequency , then press 2 (ENT) . F or the adjustable frequencies, see page 109. • It is not possible to adjust the frequencies of adjacent bands within 4 steps. 18 Press 1 ( ) or 5 ( ) , sele ...

  • Alpine PXI-H990 - page 43

    39 - EN 20 Press 1 ( ) or 5 ( ) , select “ L V [Le vel] ” , then press 2 (ENT) . 21 Press 1 ( ) or 5 ( ) , adjust the le vel ( ± 9dB 0.5dB step), then press 2 (ENT) . 22 T o adjust another band, after pressing 6 (RTN) , repeat steps 13 to 21. 23 T o adjust other channels, after pressing 6 (RTN) , repeat steps 11 to 22. 24 Once the settings are ...

  • Alpine PXI-H990 - page 44

    40 - EN Settings/Adjustments Crossover network The PXI-H990 is equipped with an activ e dividing network allo wing the bands to be split before amplification by the po wer amplifier . Because of this, there is no need for a passiv e network between the speakers and amplifiers and the amplifiers are fully independent, thus eliminating the problem of ...

  • Alpine PXI-H990 - page 45

    41 - EN L.P .F . cutoff frequency The H.P .F . setting cannot be the same as or e xceed the L.P .F . setting for that channel. • The crossov er network is a filter that divides specif ic frequency bands. • The high pass filter is a f ilter that cuts frequencies below a certain frequenc y (bass frequencies) and lets through treble frequencies. ? ...

  • Alpine PXI-H990 - page 46

    42 - EN Settings/Adjustments 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick Crossover adjustment/Switching the phase 1 Press and hold F • SETUP for at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . ...

  • Alpine PXI-H990 - page 47

    43 - EN 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MOBILE.S .MGR [Mobile Sound Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ CR OSSO VER [Crossov er] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ CH MODE [Channel Mode] ” , then press 2 (ENT ...

  • Alpine PXI-H990 - page 48

    44 - EN Settings/Adjustments 8 Press 1 ( ) or 5 ( ) , select “ CH SELECT [Channel Select] ” , then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select the channel (speaker) to be adjusted, then press 2 (ENT) . The channels that can be selected depend on the system settings (page 9). 10 Press 1 ( ) or 5 ( ) , select “ ADJUST [Adjust] ” , then pr ...

  • Alpine PXI-H990 - page 49

    45 - EN 13 Press 1 ( ) or 5 ( ) , select “ LOW .SL [Low P ass Slope] ” or “ HI.SL [High P ass Slope] ” , then press 2 (ENT) . 14 Press 1 ( ) or 5 ( ) , adjust the slope, then press 2 ( ENT ) . 15 Press 1 ( ) or 5 ( ) , select “ LEVEL [Le v el] ” , then press 2 (ENT) . 16 Press 1 ( ) or 5 ( ) , adjust the level ( – 12dB~0dB, 1dB steps) ...

  • Alpine PXI-H990 - page 50

    46 - EN Settings/Adjustments 19 T o adjust another channel, after pressing 6 (RTN) , repeat steps 8 to 18. 20 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Press 6 (R TN) or RETURN on the remote control in the setting mode to return to the previous item. Hint f or adjusting the subwoofer • If the subwoof ...

  • Alpine PXI-H990 - page 51

    47 - EN 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick MX settings MX (Media Xpander) makes vocals or instr uments sound distinct regardless of the music source. The FM radio and CD will be able to reproduce the music clearly e ven in cars with a lot of road noise. When the head unit ’ s music source is switched, the sett ...

  • Alpine PXI-H990 - page 52

    48 - EN Settings/Adjustments 4 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ MEDIA.S.MGR [Media Sound Manager] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ MX [Media Xpander] ” , then press 2 (ENT) . 7 Press 1 ( ) or 5 ( ) , select “ MX ON/OFF ” . 8 When OFF , press ...

  • Alpine PXI-H990 - page 53

    49 - EN 9 If set to ON, press 1 ( ) or 5 ( ) , select “ MEDIA SEL [Media Select] ” , then press 2 (ENT) . 10 Press 1 ( ) or 5 ( ) , select the source (medium) to be set, then press 2 (ENT) . 11 Press 1 ( ) or 5 ( ) , select “ MX SELECT [MX Select] ” , then press 2 (ENT) . Continued ...

  • Alpine PXI-H990 - page 54

    50 - EN Settings/Adjustments 12 Press 1 ( ) or 5 ( ) , select the desired mode, then press 2 (ENT) . When “ OFF ” is selected, the MX eff ect is turned off. FM: MX1 to 5 and OFF The medium to high frequencies become more clear , and produces well balanced sound in all the bands. CD: MX1 to 5 and OFF CD mode processes a large quantity of data. T ...

  • Alpine PXI-H990 - page 55

    51 - EN TITLE Performing time correction manually (Time Correction) Equalizer adjust- ments Crossover adjustment/ Switching the phase MX settings Description Time correction cannot be performed for speak ers set to “ OFF ” at the speaker settings (page 7). In reality the time difference depends not only on the difference in ph ysical distance b ...

  • Alpine PXI-H990 - page 56

    52 - EN Using the m ulti-channel function Adjustment pr ocedure for m ulti-channel function Make the adjustments described belo w in order to reproduce Dolby Digital and DTS sound with greater accuracy . Adjustment procedure • In case of combining the A utomatic adjustments etc. W e recommend to make the Automatic adjustments before the multi-cha ...

  • Alpine PXI-H990 - page 57

    53 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick Speaker setup (Dolb y SP) The PXI-H990 can be set according to the playable frequency range of your speaker s. Check the playable frequency range of the speakers (not including the subw oofer) befor e perform- ing this operation to verify whether the speakers c ...

  • Alpine PXI-H990 - page 58

    54 - EN Using the m ulti-channel function 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ SP SETUP [Speaker Setup] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ Dolby SP [Dolby Speaker Setup] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ CH SELECT [Channel ...

  • Alpine PXI-H990 - page 59

    55 - EN 8 Press 1 ( ) or 5 ( ) , select “ SETUP [Setup] ” , then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select the speaker type , then press 2 (ENT) . (Subwoof er is only ON/OFF .) LARGE: When a speaker that can pla y low frequencies is connected SMALL: When a speaker that cannot pla y low frequen- cies is connected OFF: When no speaker is co ...

  • Alpine PXI-H990 - page 60

    56 - EN Using the m ulti-channel function 10 T o adjust another speaker , repeat steps 6 to 9. Cut-off frequency setting Set the cut-off frequency to restrict the playbac k when the speaker settings are set to “ SMALL ” . P erform this setting after selecting the speaker setting of e very speaker . 1) On the mode Dolby SP , press 1 ( ) or 5 ( ) ...

  • Alpine PXI-H990 - page 61

    57 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP Adjusting the speaker le vels (OUTPUT LEVEL) Use the test tones output from the PXI-H990 to adjust so that the volume of the dif ferent speakers is equal. T o achieve a str ong sense of pr esence, adjust so that the v olume of the sound heard from the different speak ers at the listening position is the s ...

  • Alpine PXI-H990 - page 62

    58 - EN Using the m ulti-channel function 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ OUTPUT LEVEL [Output Le vel] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ CH SELE ...

  • Alpine PXI-H990 - page 63

    59 - EN 8 Press 1 ( ) or 5 ( ) , select “ LEVEL [Le v el] ” , then press 2 (ENT) . 9 Press 2 (ENT) , press 1 ( ) or 5 ( ) , adjust the output le vel, then press 6 (RTN) . Each speaker can be adjusted b y ± 10 dB ( ± 1 dB step). 10 T o adjust another speaker , repeat steps 6 to 9. 11 When the settings are completed, press 1( ) or 5 ( ) , selec ...

  • Alpine PXI-H990 - page 64

    60 - EN Using the m ulti-channel function 2(ENT) 1( ) 5( ) F • SETUP Adjusting the acoustic image (BI PHANT OM) T o achieve sound with a sense of presence, the center speak er must be placed directly in front of the driv er ’ s seat and the passenger ’ s seat. W ith this function, the center channel information is distributed to the left and ...

  • Alpine PXI-H990 - page 65

    61 - EN 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ BI PHANT OM [Bi Phantom] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ MODE ON/OFF [Bi Phantom ON/OFF] ” . 7 When ...

  • Alpine PXI-H990 - page 66

    62 - EN Using the m ulti-channel function 9 Press 1 ( ) or 5 ( ) , adjust the level, then press 2 (ENT) . The level can be adjusted within the range of – 5 to +5. The higher the le vel, the more the position of the center speaker is shifted to the sides. 10 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Pr ...

  • Alpine PXI-H990 - page 67

    63 - EN 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick Mixing the Bass Sound of the Center Channel with the Sound of the Fr ont Left and Right Channels (C.B ASS SPLIT) The (bass) audio signals of the center channel are mixed into the audio signals output from the front left and right speakers. • A void stopping, pausing, ...

  • Alpine PXI-H990 - page 68

    64 - EN Using the m ulti-channel function 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ C .BASS SPLIT [Center Bass Split] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ MO ...

  • Alpine PXI-H990 - page 69

    65 - EN 8 When ON is set, press 1 ( ) or 5 ( ) , select “ FREQ [F requency] ” , then press 2 (ENT) . 9 Press 1 ( ) or 5 ( ) , select the frequency to be set, then press 2 (ENT) . P ossible frequency setting 200Hz/225Hz/250Hz/280Hz/315Hz/ 350Hz/400Hz/450Hz/500Hz 10 Once the settings are completed, press and hold F • SETUP for at least 3 second ...

  • Alpine PXI-H990 - page 70

    66 - EN Using the m ulti-channel function 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick / Mixing bass sound to the rear channel (REAR MIX) This function mixes the front channel audio signals (lo w range) to the audio signals output from the rear speakers, improving the sound in the v ehicle ’ s rear seat. • A void stop ...

  • Alpine PXI-H990 - page 71

    67 - EN 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ REAR MIX [Rear Mix] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ MODE ON/OFF [Rear Mix ON/OFF] ” . 7 When OFF , p ...

  • Alpine PXI-H990 - page 72

    68 - EN Using the m ulti-channel function 9 Press 1 ( ) or 5 ( ) , adjust the output le vel, then press 2 (ENT) . The le vel can be adjusted in fiv e steps: – 6, – 3, 0, +3 and +6. The higher the le vel, the more bass is output from the rear speakers . (The effect diff ers according to the software (D VD , etc.).) 10 Once the settings are compl ...

  • Alpine PXI-H990 - page 73

    69 - EN 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick Outputting the Front Channel Signals from the Rear Channels (REAR FILL) When playing back 2 channel software, the front channel signals can be output from the rear channels. • This function only works with two-channel signals. This operation is ineffectiv e when 5.1-c ...

  • Alpine PXI-H990 - page 74

    70 - EN Using the m ulti-channel function 1 Press and hold F • SETUP f or at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then ...

  • Alpine PXI-H990 - page 75

    71 - EN 6 After pressing 2 (ENT) , press 1 ( ) or 5 ( ) , to s witch ON/OFF . 7 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Press 6 (R TN) or RETURN on the remote control in the setting mode to return to the previous item. Supplement See page 89 f or supplementar y information. REAR FILL REAR FIL O N REAR ...

  • Alpine PXI-H990 - page 76

    Using the m ulti-channel function 72 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick Achie ving powerful high v olume sound (LISTEN MODE) W ith Dolby Digital, the dynamic range is compressed so that powerful sound can be achie ved at regular v olume levels. This compression can be canceled to ac hieve an energeti ...

  • Alpine PXI-H990 - page 77

    73 - EN 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ LISTEN MODE [Listening Mode] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ STD [ST AND- ARD] ” or “ MAX [MAXIMUM ...

  • Alpine PXI-H990 - page 78

    Using the m ulti-channel function 74 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick Adjusting the D VD level (D VD LEVEL) The volume (signal le vel) for the Dolby Digital, Pro Logic II, DTS, DTS Neo:6 and PCM modes can be set. • A void stopping, pausing, switching the disc, cueing, fast-forwarding or switchi ...

  • Alpine PXI-H990 - page 79

    75 - EN 4 Press 1 ( ) or 5 ( ) , select “ MEDIA.S .MGR [Media Sound Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ D VD LEVEL [D VD V olume Lev el Setup] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ MODE SELECT [Mode Select] ” , then press 2 (ENT) . 7 Press 1 ( ) or 5 ( ) , select the item to be adjust ...

  • Alpine PXI-H990 - page 80

    Using the m ulti-channel function 76 - EN 9 After pressing 2 (ENT) , press 1 ( ) or 5 ( ) , adjust the lev el, then press 6 (RTN) . The lev el can be adjusted in the range of – 10dB to +10dB (2dB step). 10 Repeat steps 6 to 9 to adjust the different lev els. 11 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. ? ...

  • Alpine PXI-H990 - page 81

    77 - EN 2(ENT) 1( ) 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick 6.1-Channel Settings (6.1CH MODE) Make the Dolby Digital EX and DTS-ES decoding settings. Due to the speaker setting (page 7), you may not be able to set if SYSTEM1 or SYSTEM2 is selected. See page 107 for information on Dolby Digital EX and DTS-ES. • A void stopping, ...

  • Alpine PXI-H990 - page 82

    Using the m ulti-channel function 78 - EN 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ 6.1CH MODE [6.1ch Mode] ” , then press 2 (ENT) . Cannot select 6.1CH MODE when “ SYSTEM 1 ” or “ SYSTEM 2 ” is selected at the speak er settings (page 7). 6 Pres ...

  • Alpine PXI-H990 - page 83

    79 - EN 9 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Press 6 (R TN) or RETURN on the remote control in the setting mode to return to the previous item. Supplement See page 90 f or supplementar y information. ...

  • Alpine PXI-H990 - page 84

    Using the m ulti-channel function 80 - EN 2(ENT) 1( ) 5( ) 6(RTN) F • SETUP A. PROC. RETURN / MENU SETUP ENTER/ Joystick PCM Output Settings (PCM OUT MODE) Dolby Pro Logic II processes music signals recorded in two channels and plays them in the Surround mode. Also, the output may be set to 2 or 3 channels when playing discs recorded in linear PC ...

  • Alpine PXI-H990 - page 85

    81 - EN 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ MUL TI.CH.MGR [Multi Channel Manager] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ PCM OUT MODE [PCM Out Mode] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ PCM SELECT [PCM Mode Select] ” , then pr ...

  • Alpine PXI-H990 - page 86

    Using the m ulti-channel function 82 - EN 7 Press 1 ( ) or 5 ( ) , select the desired mode, then press 2 (ENT) . PCM STEREO : 2ch output (L/R) PCM 3ch : 3ch output (L/R/Center/Rear Center) PL II MOVIE : Suits the stereo TV shows and movie programs en- coded in Dolby Surround. It improves the sound field directivity to near that of discrete 5-channe ...

  • Alpine PXI-H990 - page 87

    83 - EN 1 In PCM OUT MODE, press 1 ( ) or 5 ( ) , select “ Dolby PL II [Dolby Pro Logic II ] ” , then press 2 (ENT) . 2 Press 1 ( ) or 5 ( ) , select “ CENTER WIDTH [Center Width] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ MODE ON/OFF [Center Width ON/OFF] ” . 4 When OFF , press 1 ( ) after pressing 2 (ENT) to s witch ON ...

  • Alpine PXI-H990 - page 88

    Using the m ulti-channel function 84 - EN 7 In Dolby PL II mode, press 1 ( ) or 5 ( ) , select “ DIM CONTROL [Dimension Control] ” , then press 2 (ENT) . 8 Press 1 ( ) or 5 ( ) , select “ MODE ON/OFF [Dimension Control ON/OFF] ” . 9 When OFF , press 1 ( ) after pressing 2 (ENT) to s witch ON. T o switch from ON to OFF , press 5 ( ) after pr ...

  • Alpine PXI-H990 - page 89

    85 - EN 12 In Dolby PL II mode, press 1 ( ) or 5 ( ) , select “ P ANORAMA ON/OFF [Panorama Mode ON/OFF] ” , then press 2 (ENT) . 13 Press 1 ( ) or 5 ( ) to switch ON/OFF , then press 2 (ENT) . When set to “ ON ” , the stereo image of the front channels expands to the surround speakers . This creates a stimulating “ envelop- ing ” effect ...

  • Alpine PXI-H990 - page 90

    Using the m ulti-channel function 86 - EN 2(ENT) 1( ) 5( ) F • SETUP RETURN / MENU SETUP ENTER/ Joystick When “ Neo:6 MUSIC [DTS Neo:6 MUSIC] ” is selected, CGAIN can be set using the procedure described below . 1 In PCM OUT MODE, press 1 ( ) or 5 ( ) , select “ DTS Neo:6 ” , then press 2 (ENT) . 2 Press 1 ( ) or 5 ( ) , select “ CGAIN ...

  • Alpine PXI-H990 - page 91

    87 - EN Supplement See page 90 f or supplementar y information. DTS Neo 6 LEVEL 0. 2 4 Press 1 ( ) or 5 ( ) , select “ LEVEL ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , adjust the level, then press 2 (ENT) . The level can be adjusted from 0 to 0.5 (0.1 step). 6 Once the settings are completed, press and hold F • SETUP for at least 3 sec ...

  • Alpine PXI-H990 - page 92

    Using the m ulti-channel function 88 - EN TITLE Speaker setup (Dolby SP) Adjusting the speaker le vels (OUTPUT LEVEL) Adjusting the acoustic image (BI PHANT OM) Description The operations performed with the remote control unit in step 1 can also be performed by pressing and holding MENU (SETUP) f or at least 3 seconds , moving the joystic k up or d ...

  • Alpine PXI-H990 - page 93

    89 - EN TITLE Mixing the Bass Sound of the Center Channel with the Sound of the F ront Left and Right Channels (C.BASS SPLIT) Mixing bass sound to the rear channel (REAR MIX) Outputting the F ront Channel Signals from the Rear Channels (REAR FILL) Achieving po werful high volume sound (LISTEN MODE) Adjusting the D VD lev el (D VD LEVEL) Description ...

  • Alpine PXI-H990 - page 94

    Using the m ulti-channel function 90 - EN TITLE 6.1-Channel Settings (6.1CH MODE) PCM Output Settings (PCM OUT MODE) Description The operations performed with the remote control unit in step 1 can also be performed by pressing and holding MENU (SETUP) for at least 3 seconds, moving the jo ystick up or down to select “ AP SETUP ” , then pressing ...

  • Alpine PXI-H990 - page 95

    91 - EN 2(ENT) 1( ) SOURCE/POWER 5( ) F • SETUP A. PROC. RETURN MENU SETUP ENTER/ Joystick 1 Press and hold F • SETUP for at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ A UX SETUP ” , then press 2 (ENT) . Con venient Functions External in ...

  • Alpine PXI-H990 - page 96

    92 - EN Convenient Functions 4 After pressing 2 (ENT) , press 1 ( ) or 5 ( ) , to s witch ON/OFF . 5 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • After setting A UX ON/OFF , turn the ignition key to OFF , and switch the ignition key to ACC or ON again. The setting contents are realized. • If 6 (R TN) or ...

  • Alpine PXI-H990 - page 97

    93 - EN F • SETUP 1~6 Function Indicator A. PROC. RETURN MENU SETUP ENTER/ Joystick Storing settings in the memory W ith the PXI-H990, up to six sets of adjustments and settings you have made can be stored in the memory . The adjustment and setting items listed below are all stored at one preset memor y position. Setting the speakers Time correct ...

  • Alpine PXI-H990 - page 98

    94 - EN Convenient Functions 1 Press and hold F • SETUP f or at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . 4 Press 1 ( ) or 5 ( ) , select “ PRESET [Preset] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ...

  • Alpine PXI-H990 - page 99

    95 - EN 6 Press 1 ( ) or 5 ( ) , select “ STORE [Store] ” , then press 2 (ENT) . 7 Press 1 ( ) or 5 ( ) , select “ PRESET NO [Preset No .] ” , then press 2 (ENT) . 8 Press 1 ( ) or 5 ( ) , select the preset number at which the settings are to be stored, then press 2 (ENT) . Appro ximately 5 seconds are required for the processing to be comp ...

  • Alpine PXI-H990 - page 100

    96 - EN Convenient Functions A. PROC. RETURN MENU SETUP ENTER/ Joystick 1 Press and hold F • SETUP f or at least 3 seconds. 2 Press 1 ( ) or 5 ( ) , select “ M.M.Manager [Multi Media Manager] ” , then press 2 (ENT) . 3 Press 1 ( ) or 5 ( ) , select “ AP SETUP ” , then press 2 (ENT) . Calling out stored v alues 1~6 F • SETUP Function Ind ...

  • Alpine PXI-H990 - page 101

    97 - EN 4 Press 1 ( ) or 5 ( ) , select “ PRESET [Preset] ” , then press 2 (ENT) . 5 Press 1 ( ) or 5 ( ) , select “ MODE [Recall or Store] ” , then press 2 (ENT) . 6 Press 1 ( ) or 5 ( ) , select “ RECALL [Recall] ” , then press 2 (ENT) . 7 Press 1 ( ) or 5 ( ) , select “ PRESET NO [Preset No .] ” , then press 2 (ENT) . 8 Press 1 ( ...

  • Alpine PXI-H990 - page 102

    98 - EN Convenient Functions 9 Once the settings are completed, press and hold F • SETUP for at least 3 seconds. • Press 6 (R TN) or RETURN on the remote control in the setting mode to return to the previous item. Easily calling out v alues in the memory 1 Press F • SETUP so that the function indicator becomes blue . 2 Press a button from 1 t ...

  • Alpine PXI-H990 - page 103

    99 - EN A. PROC. RETURN MENU SETUP ENTER/ Joystick / Equalizer adjustment (when D VI-9990/TMI- M990 is connected) When using the (DVI-9990) head unit and the (TMI-M990) monitor (both sold separately) in the system (page 32), EQ adjustments ar e reflected in the data on the head unit ’ s and monitor ’ s displa ys. The operation is from the remot ...

  • Alpine PXI-H990 - page 104

    100 - EN Convenient Functions 6 Use Joystic k to select “ L/R ” or “ L+R ” , and press ENTER . L/R: Independent adjustment values can be set to the Left and Right channels. L+R: The same adjustment values are set to the Left and Right channels. When “ L+R ” have been selected, use Jo ystick to select L or R, and press ENTER . L : V alid ...

  • Alpine PXI-H990 - page 105

    101 - EN 9 Adjust all the frequency bandwidths with the operations of step 8, then press ENTER . 10 T o adjust another channel, repeat steps 7 to 9. 11 Once the settings hav e been completed, press and hold MENU/SETUP f or at least 3 seconds. ...

  • Alpine PXI-H990 - page 106

    102 - EN Convenient Functions 6 Use Joystic k to select “ L/R ” or “ L+R ” , and press ENTER . L/R: Independent adjustment values can be set to the Left and Right channels. L+R: The same adjustment values are set to the Left and Right channels. When “ L+R ” have been selected, use Joystick to select L or R, and press ENTER . L: V alidat ...

  • Alpine PXI-H990 - page 107

    103 - EN 9 Use Joystick to select the “ Freq ” (frequency), “ Width ” (bandwidth (Q)), and “ Level ” items, then press or and adjust the various items. • See Page 109 for information about the adjustable frequencies. The frequencies of adjacent bands cannot be adjusted to within 4 steps. • The bandwidth can be adjusted to the 6 lev ...

  • Alpine PXI-H990 - page 108

    104 - EN Convenient Functions TITLE External input settings Storing settings in the memory Calling out stored values Equalizer adjust- ment (when D VI- 9990/TMI-M990 is connected) Description The operations perf or med with the remote control unit in step 1 can also be performed by pressing and holding MENU (SETUP) f or at least 3 seconds, moving t ...

  • Alpine PXI-H990 - page 109

    105 - EN Inf or mation About the Monitor Display D V D P L A Y E R VOL. - 28dB AP Preset - 1 0 : 17 V I D E O Title 3 Chapt. 1 Time 000’ 32” R C S L s R s LFE L Preset Number Display Input Signal Display The display will change depending on the input signal. The display will appear toned down in the absence of a signal. L : Left front channel R ...

  • Alpine PXI-H990 - page 110

    106 - EN Inf or mation T erminology Dolby Digital Dolby Digital is a digital audio compression technology dev eloped by Dolby Labor ator ies that allows large quantities of audio data to be efficiently recorded on discs. It is compatible with audio signals from mono (1 channel) all the wa y up to 5.1-channel surround sound. The signals for the diff ...

  • Alpine PXI-H990 - page 111

    107 - EN Dolby Digital EX Dolb y Digital EX is a technology that creates full-bandwidth output in programs from 5.1 channels to 6 channels. Using a matrix decoder, 3 surround channels are e xtracted from the signals that are recorded on the 2 channels of the program. Use this function with Dolby Digital surround EX movie soundtrac ks to bring out o ...

  • Alpine PXI-H990 - page 112

    108 - EN Inf or mation In case of difficulty If you encounter a problem, please re view the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer . Set does not operate. Nothing appears on the ...

  • Alpine PXI-H990 - page 113

    109 - EN Specifications Graphic EQ number of bands: Front (left and right) 31 bands Rear (left and right) 31 bands Center 31 bands Subwoofer 10 bands Graphic EQ boost cut range: ± 9 dB Parametric EQ number of bands: Front/rear/center 10 bands Subwoofer 2 bands Parametric EQ frequency: Front, Rear and Center Band 1: 20/22/25/28/31.5/36/40/45/50/56/ ...

  • Alpine PXI-H990 - page 114

    110 - EN Inf or mation <Components> Parts name Quantity P ar ts for mounting ....................................................................................... 1set Owner ’ s manual ........................................................................................... 1set Microphone ............................................... ...

  • Alpine PXI-H990 - page 115

    111 - EN Directory Menu Some menu cannot be selected depending on the displayed condition. . CH SELECT [Channel Select] . ADJUST [Adjust] . CH MODE [Channel Mode] . CH SELECT [Channel Select] . ADJUST [Adjust] . CH MODE [Channel Mode] . AUT O TCR [Auto Time Correction] . TCR ON/OFF [Time Correction ON/OFF] . CH SELECT [Channel Select] . BAND [Band] ...

  • Alpine PXI-H990 - page 116

    LIMITED W ARRANTY ALPINE ELECTRONICS OF AMERICA, INC. AND ALPINE OF CANADA INC. ("Alpine"), are dedicated to quality craftsmanship and are pleased to offer this Warranty. We suggest that you read it thoroughly. Should you have any questions, please contact your Dealer or contact Alpine at one of the telephone numbers listed below. [ [ [ [ ...

Fabricant Alpine Catégorie Cooktop

Les documents que nous recevons du fabricant de l'appareilAlpine PXI-H990 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Alpine
- manuels d’utilisations PXI-H990
- fiches produit Alpine
- dépliants
- ou étiquettes-énergie Alpine PXI-H990
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Alpine PXI-H990.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Alpine PXI-H990, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Alpine PXI-H990. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Alpine PXI-H990.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Alpine PXI-H990, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Alpine PXI-H990 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Alpine PXI-H990.

Le manuel d’utilisation complet Alpine, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Alpine PXI-H990 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Alpine PXI-H990, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAlpine PXI-H990 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Alpine PXI-H990 - qui devraient nous aider dans les premières étapes lors de l'utilisation Alpine PXI-H990
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Alpine PXI-H990
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Alpine PXI-H990 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Alpine PXI-H990?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Alpine PXI-H990, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Alpine PXI-H990 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)