Français dropdown-ico

Manuel d’utilisation Runco DTV-940/943

69 pages 1.67 mb
Télécharger

Aller à la page of 69

Summary
  • Runco DTV-940/943 - page 1

    O WNER ’ S O PERA TING M ANUAL DTV Capable CR T Projector DT V -94 0/943 ...

  • Runco DTV-940/943 - page 2

    ...

  • Runco DTV-940/943 - page 3

    i-1 T ABLE OF CONTENTS T ABLE OF CONTENTS............................................................................................................................1 SAFETY INSTRUCTIONS ............................................................................................................................... . 1-1 On safety.................... ...

  • Runco DTV-940/943 - page 4

    i-2 T ABLE OF CONTENTS RANDOM ACCESS ADJUSTMENT MODE .................................................................................................. 6-1 Starting up the Random Access Adjustment mode ............................................................................................6-1 Overview ‘Random Access Adjustment’ mode ....... ...

  • Runco DTV-940/943 - page 5

    T ABLE OF CONTENTS Hardware Configuration ......................................................................................................... ................................9-1 How to format the control data................................................................................................. ..............................9-1 Send ...

  • Runco DTV-940/943 - page 6

    T ABLE OF CONTENTS Error Messages ................................................................................................................. .................................10-13 No Pattern Error ................................................................................................................ ................................. ...

  • Runco DTV-940/943 - page 7

    1-1 SAFETY INSTRUCTIONS Notice on Safety This equipment is built in accordance with the requirements of the international safety standards EN60950, UL 1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including electrical business equipment. These safety standards impose important requirements on the use ...

  • Runco DTV-940/943 - page 8

    1-2 Safety Instructions A. Mains lead (Power cord) with CEE 7 plug: The wires of the mains lead are colored in accor- dance with the following code. Green and yellow: earth (safety earth) Blue: neutral Brown: line (live) B. Power cord with ANSI 73.1 1 plug: The wires of the power cord are colored in accor- dance with the following code. Green/yello ...

  • Runco DTV-940/943 - page 9

    2-1 LOCA TION AND FUNCTION OF CONTROLS RS 232 Input Port Connection between the controller and projector . Connect the RS- 232 output from the controller to this port. RS 232 Output Port RS 232 Input Port allows a communication link for PC or MAC to the next projector in a series of projectors. IR Sensor Receiver for control signals transmitted fro ...

  • Runco DTV-940/943 - page 10

    2-2 LOCA TION AND FUNCTION OF CONTROLS IR T ransmission Indicator ADJ. : Adjust key , to enter or exit the adjustment mode. Address key (recessed key) : to enter the address of the projec- tor (between 0 and 9). Press the address key , followed by press- ing one digit button between 0 and 9. When addressed to O , the remote will talk to any project ...

  • Runco DTV-940/943 - page 11

    3-1 CONNECTIONS AC Power (mains) Cord Connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector on the front of the projector . Power Check The power voltage is determined by the sticker on the front of the projector . W arning! V erify the power voltage corresponds ...

  • Runco DTV-940/943 - page 12

    3-2 Connections SOURCE SELECTION SELECT AN INPUT FROM BELO W: RGB S-VIDEO VIDEO COMPONENT VIDEO Select with or then <ENTER> <EXIT> to return FROM RCU GENERAL ACCESS SHARPNESS TINT COLOR BRIGHTNESS CONTRAST 56 34 12 Enter ADJUST Select with , or then <ENTER>. <EXIT> to return FROM LOCAL KEYP AD RS232 IN RS232 OUT IR COMM PORT ...

  • Runco DTV-940/943 - page 13

    3-3 Connections GENERAL ACCESS SHARPNESS TINT COLOR BRIGHTNESS CONTRAST 56 34 12 Enter ADJUST Select with , or then <ENTER>. <EXIT> to return FROM LOCAL KEYP AD ...

  • Runco DTV-940/943 - page 14

    3-4 Connections GENERAL ACCESS SHARPNESS TINT COLOR BRIGHTNESS CONTRAST 56 34 12 Enter ADJUST Select with , or then <ENTER>. <EXIT> to return FROM LOCAL KEYP AD ...

  • Runco DTV-940/943 - page 15

    3-5 Connections GENERAL ACCESS SHARPNESS TINT COLOR BRIGHTNESS CONTRAST 56 34 12 Enter ADJUST Select with , or then <ENTER>. <EXIT> to return FROM LOCAL KEYP AD RS232 IN RS232 OUT IR COMM PORT REMOTE R G(s) B H V VIDEO S - VIDEO This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1), Thi ...

  • Runco DTV-940/943 - page 16

    3-6 (R-Y)Y(B-Y)3S or (R-Y)Y3s(B-Y) input selection a. W ith the RCU: Select “Component” in the Source Selection Menu b. W ith the local keypad : (to gain access to the local keypad, see ‘Local keypad’ in chapter ‘Location and function of controls’.) -Press ADJUST key , the General access menu is displayed on the screen. -Use the control ...

  • Runco DTV-940/943 - page 17

    4-1 CONTROLLING The DT V - 94 94 3 can be controlled with a. The RCU b. The hardwired RCU (cable not included) c. The local keyboard The procedure and results of controlling the projector with either of these RCU options is essentially the same. How to use your RCU a) Point the front of the RCU towards the projector b) RCU used in a hardwired confi ...

  • Runco DTV-940/943 - page 18

    4-2 Controlling Input selection. T wo possible ways of selecting an input : a) Display General access menu with RCU by pressing ADJ button. This brings up a secondary general access menu. Choose source selec- tion and highlight desired source. b) W ith the local keypad : Press first the ADJUST key to display the General access menu. Use the control ...

  • Runco DTV-940/943 - page 19

    4-3 Controlling Analog Picture Controls The analog picture controls can be adjusted with the RCU. The control keys are located on the lower right side of the key panel of the RCU and indicated with the name of the control and an icon. When an analog picture control is pressed, a text box with bar scale and the function name of the control, e.g. ‘ ...

  • Runco DTV-940/943 - page 20

    5-1 ST AR T UP OF THE ADJUSTMENT MODE Adjustment mode All picture geometry and convergence adjustments are made while in the ‘Adjustment mode’. T wo possible ways to enter the adjust ment mode: a) Using the RCU . Press the ADJUST key . The projector displays the path selection menu. b) Using the local keypad. Press the ADJUST key . The projecto ...

  • Runco DTV-940/943 - page 21

    5-2 Start Up of the Adjustment Mode RANDOM ACCESS - Random Access should be selected if the user intends to make only a few adjustments. SER VICE - Service should be selected if the user intends to delete blocks, change pass- word or apply information. EYE-Q - This selection will only be available when the subconver gence unit EYE-Q is connected to ...

  • Runco DTV-940/943 - page 22

    6-1 RANDOM ACCESS ADJUSTMENT MODE Starting up the random access adjustment mode. Push the control disc up or down to highlight “RANDOM ACCESS” and the press ENTER. Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also ...

  • Runco DTV-940/943 - page 23

    6-2 Random Access Adjustment Mode Selecting Setup Pattern If an external source is connected to the projector , this menu will be displayed. Push the con- trol disc up or down to highlight the desired setup pattern and then press ENTER. Genlocked pattern : internally generated cross hatch pattern, locked on the external source. NOTE: The Genlocked ...

  • Runco DTV-940/943 - page 24

    6-3 Random Access Adjustment Mode Random access adjustment mode selection menu. This is the main menu for the Random Access adjustment mode. Through this menu, the following adjustments and features are accessible: - Picture T uning Sync slow/fast (video/s-video) Color Balance - Geometry Convergence - Color Select Picture T uning Highlight Picture ...

  • Runco DTV-940/943 - page 25

    6-4 Random Access Adjustment Mode Peaking Peaking improves the contours in a projected image. Highlight PEAKING by push- ing the control disc up or down and press ENTER to toggle the peaking between OFF and ON. During the creation of new settings for a RGB source the peaking is switched to OFF . Color Select Highlight COLOR SELECT by pushing the co ...

  • Runco DTV-940/943 - page 26

    6-5 Random Access Adjustment Mode Geometry Adjustments The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color images : Left-right (EW) and T op-Bottom Cor- rections, Blanking, Horizontal Amplitude, V ertical Amplitude, V ertical Linearity and Horizon- tal Phase. Highligh ...

  • Runco DTV-940/943 - page 27

    6-6 Random Access Adjustment Mode Raster Shift Adjustment The green raster must be centered both horizontally and vertically on the center of the CR T surface. T o center the green raster , look into the green lens and use the control disc to move the raster . CAUTION It is necessary to look into the lenses to perform these adjustments. T o avoid e ...

  • Runco DTV-940/943 - page 28

    6-7 Random Access Adjustment Mode Left-Right (east-west) Adjustments Left-right and center adjustments affect only the vertical lines of the projected image. T o start up the left-right and center adjustments, follow the next procedure : Push the control disc up or down to highlight LEFT -RIGHT (E/W) on the geometry menu and then press ENTER . Only ...

  • Runco DTV-940/943 - page 29

    6-8 Random Access Adjustment Mode GEOMETR Y H PHASE RASTER SHIFT LEFT - RIGHT (E-W) SIZE V LINEARITY BLANKING Select with then <ENTER> <EXIT> to return. or TOP - BO TT OM (N-S) TOP - BO TTOM (N-S) H CENTERLINE BO W H CENTERLINE SKEW TOP BO W TOP KEYST ONE BOTT OM KEYST ONE BOTT OM BO W Select with then <ENTER> <EXIT> to retu ...

  • Runco DTV-940/943 - page 30

    6-9 Random Access Adjustment Mode Size Adjustment Push the control disc up or down to highlight SIZE on the Geometry menu and then press ENTER . ENTER will select size adjustment. EXIT returns to random access adjustment mode menu. ADJUST returns to operational mode. Adjust the horizontal size by pushing the control disc to the right or to the left ...

  • Runco DTV-940/943 - page 31

    6-10 Random Access Adjustment Mode GEOMETR Y H PHASE RASTER SHIFT LEFT - RIGHT (E-W) TOP - BO TT OM (N-S) H & V SIZE V LINEARITY Select with then <ENTER> <EXIT> to return. or BLANKING T op blanking Bottom blanking Left blanking Right blanking BLANKING TOP BOTT OM LEFT RIGHT Select with then <ENTER> <EXIT> to return. Adju ...

  • Runco DTV-940/943 - page 32

    6-11 Random Access Adjustment Mode Convergence Adjustment Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image. Start with the coarse convergence adjustments a ...

  • Runco DTV-940/943 - page 33

    6-12 Random Access Adjustment Mode V ertical corners Highlight ‘V ertical corners’ and press ENTER to start the adjustment. T o make a coarse adjustment of the red or blue horizontal lines in zone 10, 14, 18 and 22 simultaneously . Hint: - Adjust until the red or the blue horizontal lines are on the green lines or as close as possible to the gr ...

  • Runco DTV-940/943 - page 34

    7-1 SER VICE MODE Starting up the Service mode. Use the control stick to highlight ‘Service’ and then press ENTER. Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password pro- tected items are now also available if you stay in the adjustment mode. ENTER co ...

  • Runco DTV-940/943 - page 35

    7-2 Service Mode Projector Set-up Highlight ‘Projector Set-Up’ by pushing the control disc up or down and press ENTER to display the projector set-up menu. W ithin the projector set-up menu, the following items can be consolidated or set to the desired setting : - Identification - T otal run time - Change password - Change language - Change pro ...

  • Runco DTV-940/943 - page 36

    7-3 Service Mode T otal Run Time Highlight ‘T otal Run T ime’ with the control disc and press ENTER to dis- play the amount of time the projector has played since its first start up at the factory . Note : all projectors leave the factory after a burn-in period of approxi- mately 100 hours. Change password This item is password protected. Highl ...

  • Runco DTV-940/943 - page 37

    7-4 Service Mode Change Projector Address Every projector requires an individual address between 0 and 255. This address can be software installed. T o change that address, push the control disc up or down to highlight ‘Change Pro- jector Address’ and press ENTER. The Change Projector Address menu will be displayed and the actual address will b ...

  • Runco DTV-940/943 - page 38

    7-5 Service Mode Memory management Highlight ‘Memory management’ by pushing the control disc up or down and press ENTER to display the memory management menu. W ithin the memory management menu, the following items can be consolidated or executed : - copy a block - delete a block - delete all blocks - all settings to midposition - R&B conve ...

  • Runco DTV-940/943 - page 39

    7-6 Service Mode Deletion of blocks This item is password protected. The delete function is used to clear all data (settings) from an adjustment block. A delete can be given : - block by block or - for all blocks. Deleting block by block The ‘delete a block’ function deletes the settings of a selected block. Highlight ‘Delete a block’ with ...

  • Runco DTV-940/943 - page 40

    7-7 Service Mode MEMOR Y MANA GEMENT COPY A BLOCK DELETE A BLOCK DELETE ALL BLOCKS R & B CONVERGENCE MID GR CONVERGENCE MID Select with then <ENTER> <EXIT> to return. or ALL SETTINGS TO MIDPOS All settings to midposition Item is password protected. Highlight ‘All settings to midposition’ with the control disc and press ENTER to ...

  • Runco DTV-940/943 - page 41

    7-8 Undo R & B convergence mid When “R & B convergence mid” is selected, all convergence settings are set to their midposition. T o cancel this action, select ‘Undo R & B convergence mid’ by pushing the control disc up or down and press ENTER. ‘Undo R & B convergence mid’ is displayed in the Memory management menu instea ...

  • Runco DTV-940/943 - page 42

    7-9 Service Mode G2 Adjustment Item is password protected. Highlight ‘G2 adjust’ with the control disc and press ENTER to continue. A safety notice will be displayed on the screen as it is necessary to open the top cover to adjust the G2. ‘G2 adjustment should be performed by RUNCO personnel, or RUNCO authorized dealers’. If you are qualifi ...

  • Runco DTV-940/943 - page 43

    7-10 Service Mode If a memory block adjusted on an internal # pattern is available, the CR T run in cycle will start when pressing ENTER . If no such block is available, the projec- tor cannot run the CR T run in option and leaves the adjustment mode. If you still want to run CR T run in cycle, create first a memory block on an inter- nal # pattern ...

  • Runco DTV-940/943 - page 44

    7-11 Service Mode I2C Diagnostics Highlights ‘I2C Diagnostics’ by pushing the control disc up or down and press ENTER. The I2C diagnostics menu gives an overview of the I2C failure inside the projec- tor . T o scroll through the failure list, push the control disc up or down. The I2C address, IC number and module name will be given in I2C diagn ...

  • Runco DTV-940/943 - page 45

    8-1 MESSAGES, W ARNINGS, AND F AILURES When selecting a new source, information about this source will be displayed on the screen. Source number , horizontal and vertical frequencies of the dis- played source. Announcement of the selected source. Message to enter your password. Password contains 4 digits. These messages will be dis- played on the s ...

  • Runco DTV-940/943 - page 46

    8-2 Messages, W arnings, and Failures Communication error between EYE-Q and the projector . Call a qualified service technician. Message during the start up of the EYE-Q is ready to accept commands. Message when one of the fans are not working anymore. Pro- jector switches to stand-by . F AILURE EYE-Q commu- nication error W AIT starting up EYE-Q F ...

  • Runco DTV-940/943 - page 47

    9-1 RS-232 CONTROL TXD RXD GND CTS DSR PC TXD RXD GND +9V +9V Projector 3 2 5 8 6 3 2 5 8 6 Recommended Method Pin to Pin All 9 Pins By fa r , the most accurate way to control or integrate the DT V - 940/ 94 3 into a home theater system is by RS 232 control. In this sec t ion, you will find hardware configuration and how to format the control data, ...

  • Runco DTV-940/943 - page 48

    9-2 RS-232 CONTROL Sending a RECORD (single instruction) A RECORD consists of 9 bytes of information in the following order: STX, OFFS, ADR, CMD, DA T1, DA T2, DA T3, DA T4, CHKS Wher e: STX - 02H Make projector(s) listen for its (their) unique address. OFFS - (1-255) Offset you choose so that none of the data or CMDs - 02H (STX). Normally set the ...

  • Runco DTV-940/943 - page 49

    9-3 RS-232 CONTROL 2 4 71 8 4 4 44 2 1 STX Off est ADRe CMDe D A Tle D A T2e D A T3e DA T4e CHKSe Alwa ys 2 W ake up projo Y ou choose offset. This is added to the rest of the bytes so that none of them equal 2 which would mak e the projector think its being told to wak e up again. Normally this is 0. It is set to 4 in this w orking example to show ...

  • Runco DTV-940/943 - page 50

    9-4 RS-232 CONTROL COMMAND BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8 BYTE 9 POWER ON/OFF $02 $00 $00 $0E $00 $00 $00 $00 $0E POWER ON $02 $00 $00 $51 $0A $00 $00 $01 $5C POWER OFF $02 $00 $00 $51 $0A $00 $00 $00 $5B ENTER $02 $00 $00 $07 $00 $00 $00 $00 $07 EXIT $02 $00 $00 $08 $00 $00 $00 $00 $08 ADJUST $02 $00 $00 $09 $00 $00 $00 $0 ...

  • Runco DTV-940/943 - page 51

    10-1 EYE-Q TM Autoconvergence OVER VIEW The EYE-Q TM auto-convergence system allows for faster and more accurate conver gence when used by the installer upon initial instal- lation. The EYE-Q TM system also allows the end-user to perform occasional conver gence touch ups without having to learn the com- plex convergence procedure using the TOUCH-UP ...

  • Runco DTV-940/943 - page 52

    10-2 EYE-Q TM AUT OCONVERGENCE Easy-to-use, high precision automatic convergence system. V arious options on the menu offer you the solution for your own individual needs: Align: convergence starts for the current image situation Align from mid-position: convergence starts from mid-posi- tion. T ouch-up: convergence starts when the source switches ...

  • Runco DTV-940/943 - page 53

    10-3 EYE-Q TM Autoconvergence ON - SCREEN OPERA TING INSTRUCTIONS ACCESS TO EYE-Q TM ON-SCREEN MENUS After the EYE-Q TM unit has been correctly installed in the projec- tor , press the <ADJUST > button on the RCU (Remote Control Unit) or the local keypad of the projector to enter the ‘Adjustment mode’ (please refer to the projector Owner ...

  • Runco DTV-940/943 - page 54

    EYE-Q TM SETUP The EYE-Q TM SETUP procedure needs to be done only once after projector is correctly installed or whenever the projector is rein- stalled in another position. T o enter the EYE-Q TM SETUP menu: Highlight EYE-Q TM by pushing the or keys of the con- trol disc. Press the <ENTER> button to set the correct projector con- figuration. ...

  • Runco DTV-940/943 - page 55

    10-5 EYE-Q TM Autoconvergence FOCUSING THE CAMERA LENS The lens of the camera must be focused properly on the projection screen. Follow the steps described below: In the EYE-Q ...

  • Runco DTV-940/943 - page 56

    10-6 EYE-Q TM Autoconvergence CENTERING THE CAMERA The camera must be centered in middle of the projection screen. Follow the steps described below: Highlight CENTER CAMERA by pushing the up or down keys of the control disc. Press the <ENTER> button to start up the process. Note: It is critical that the green raster of the presently selected ...

  • Runco DTV-940/943 - page 57

    10-7 Appendix 2 CENTERING THE CAMERA VER TICALL Y One horizontally centered green bar will be projected onto the screen, together with a text box. Inside the box, the text of “CAM- ERA ALIGNMENT VER TICAL” indicates the item subject to adjustment and a symmetrical bar scale (from -50 to +50) under the text. If the indicated value below the bar ...

  • Runco DTV-940/943 - page 58

    10-8 EYE-Q TM Autoconvergence TOUCH-UP ON TIMER This option allows the static convergence to be carried out auto- matically after a user-defined time, which can be programmed in hours and/or minutes. T o program the touch-up on T imer: Push up or down keys of the control disc to highlight ON TIMER: off; Press the <ENTER> button to switch it t ...

  • Runco DTV-940/943 - page 59

    10-9 EYE-Q TM Autoconvergence LEARNING A REFERENCE Adjust one Reference Source with perfect geometry . This source can have either hori- zontal or vertical frequency . Remember that other sources will have the same geometry as this Reference Source. This means that if a source has 4:3 aspect ratio, all sources will be adjusted with a 4:3 aspect rat ...

  • Runco DTV-940/943 - page 60

    10-10 EYE-Q TM Autoconvergence TOUCH UP AND AUT OCONVERGENCE ADJUSTING SCREEN SIZE In case the projection screen is not greater than the desired size or the screen has a frame around it (i.e. projection impossible outside the frame), the following blanking adjustments have to be done before starting the automatic convergence: When using a video sou ...

  • Runco DTV-940/943 - page 61

    10-11 EYE-Q TM Autoconvergence TOUCH-UP When T OUCH-UP is selected, only the static convergence of the currently selected source will be carried out automatically . Follow the steps below to select: Highlight T OUCH-UP by pushing up or down keys of the con- trol disc; Press the <ENTER> button to start up the static convergence. If the process ...

  • Runco DTV-940/943 - page 62

    10-12 EYE-Q TM Autoconvergence ON ALL SOURCES The “On all sources” functions as the “On current source.” It includes also three options: T ouch-up Align Align from mid-position The difference is that the conver gences will be carried out on all sources of the projector , i.e. all available memory banks of the pro- jector . The total number ...

  • Runco DTV-940/943 - page 63

    10-13 EYE-Q TM Autoconvergence ALIGN FROM MIDPOSITION ON ALL SOURCES When ALIGN FROM MIDPOSITION is selected, the automatic convergence on all sources will be carried out automatically , but starting from the midposition settings. By projecting alternately red and blue lines, 25 convergence areas are aligned to the green pattern. The process will r ...

  • Runco DTV-940/943 - page 64

    10-14 EYE-Q TM Autoconvergence NO P A TTERN ERROR After starting up the automatic convergence, the projector will start to calculate and locate 5 horizontal and 5 vertical lines which are used to divide the screen into 25 areas. If the projector does not succeed in finding the pattern, it will try two time. If the two attempts fail, the projector w ...

  • Runco DTV-940/943 - page 65

    10-15 EYE-Q TM Autoconvergence EYE-Q TM DIAGNOSTICS This option allows a check-up of the EYE-Q TM NOTE: Most errors that occur during the LEARN REFERENCE procedure or the beginning of the AUT OCONVERGENCE pro- cedure are caused by one of the following: Lens cap not removed Lens focus not performed properly Camera focus not performed properly Ambien ...

  • Runco DTV-940/943 - page 66

    10-16 EYE-Q TM Autoconvergence In case of failures, the error message will shown: If all the tests are successful, the EYE-Q TM F AILED... Error 1 1; or menu will be as follows: F AILED... Error 12; or Press the <EXIT> button to return to the EYE-Q TM F AILED... Error 13; or F AILED... Error 14; or F AILED... Error 15. During the Sync T est, ...

  • Runco DTV-940/943 - page 67

    Aspect Ratios: Anamorphic, Widescreen, 4:3 Bandwidth: 75 MHz Cabinet Dimensions: Width: 22 in./558.80 mm Depth: 29 in./736.60 mm Height: 12 in./304.80 mm Weight: 96 lbs./43.55 kg Color Balance: 3200K, 5400K, 6500K, 9300K, Custom Configurations: Front or rear , floor or ceiling mount Contrast Ratios: 100:1 Convergence: Dynamic geometry , 25 point zo ...

  • Runco DTV-940/943 - page 68

    ...

  • Runco DTV-940/943 - page 69

    2 900 Faber Street Union City , C A 945 87 510- 324 - 7777 Fax: 510- 324 - 9300 RUMA-00 7 8 00 10-00 ...

Fabricant Runco Catégorie CRT Television

Les documents que nous recevons du fabricant de l'appareilRunco DTV-940/943 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Runco
- manuels d’utilisations DTV-940/943
- fiches produit Runco
- dépliants
- ou étiquettes-énergie Runco DTV-940/943
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Runco DTV-940/943.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Runco DTV-940/943, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Runco DTV-940/943. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Runco DTV-940/943.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Runco DTV-940/943, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Runco DTV-940/943 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Runco DTV-940/943.

Le manuel d’utilisation complet Runco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Runco DTV-940/943 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Runco DTV-940/943, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRunco DTV-940/943 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Runco DTV-940/943 - qui devraient nous aider dans les premières étapes lors de l'utilisation Runco DTV-940/943
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Runco DTV-940/943
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Runco DTV-940/943 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Runco DTV-940/943?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Runco DTV-940/943, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Runco DTV-940/943 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)