Manuel d’utilisation Amana AMH*

17 pages 0.39 mb
Télécharger

Aller à la page of 17

Summary
  • Amana AMH* - page 1

    C US ® RT6621017r1 April 2010 This manual is to be used by qualified, professionally trained HV AC technicians only . Goodman does not assume any responsibility for property damage or personal injury due to improper service procedures or services performed by an unqualified person. ® is a registered trademark of Maytag Corporation or its related ...

  • Amana AMH* - page 2

    PRODUCT IDENTIFICA TION 2 The model and manufacturing number are used for positive identification of component parts used in manufacturing. Please use these numbers when requesting service or parts information. WARNING WARNING HIGH VOLTAGE! Disconnect ALL power before servicing or installing this unit. Multiple power sources may be present. Failure ...

  • Amana AMH* - page 3

    PRODUCT IDENTIFICA TION 3 The model and manufacturing number are used for positive identification of component parts used in manufacturing. Please use these numbers when requesting service or parts information. * Indicates minor revision & is not used for order entry or inventory management AMH80453AXC* AMH80703AXC* AMH80704BXC* AMH80903BXC* AM ...

  • Amana AMH* - page 4

    4 PRODUCT DESIGN WA R N I N G T O PREVENT P OSSI BLE PERSONAL I NJURY OR DEATH DUE TO ASPHYX I ATI ON, THI S FURNACE M UST BE C AT E GOR Y I VENT ED. D O NOT VENT USI NG C ATEGORY III VEN TI NG. 1. Category I Venting is venting at a non-positive pressure. A furnace vented as Category I is considered a fan-as- sisted appliance and the vent system do ...

  • Amana AMH* - page 5

    5 PRODUCT DESIGN Accessibility Clearances (Minimum) Unobstructed front clearance of 24" for servicing is rec- ommended. SW B 1 0 36 11 * 24" clear ance f or s erviceab ility recom me nded. MINIM UM CLEARA NCE TO COMBUSTIBLE MATERIAL S - INCHES ** Si ngle Wall Vent (SW ) to be us ed only as a con ncetor. Refer to the venting ta bles outl i ...

  • Amana AMH* - page 6

    COMPONENT IDENTIFICA TION 6 躀 Pressure Switch T ubul ar Heat E xchanger Flu e Pi pe C onnec ti o n Gas L i ne Entrance (Al tern at e) Indu ced Draf t Blowe r Gas Line En tr a nc e Gas V alve Roll o ut Li mit Junc tion Box Wiri ng Har nes s Grommet Gas Ma nif old Inshot Burne r Blower Door Interlock Switch Integrated Contr ol Module T rans for mer ...

  • Amana AMH* - page 7

    PRODUCT DIMENSIONS 7 AMH8 MO D EL S A B AMH 8 0 4 5 3 AX** AMH 8 0 7 0 3 AX** 14 1 2 - 1/ 2 AMH 8 0 7 0 4 BX** AMH 8 0 9 0 3 BX** AMH 8 0 9 0 4 BX** 17-1 / 2 16 A MH8 09 05C X * * A MH8 11 55C X * * 21 1 9 - 1/ 2 A MH8 140 5D X * * 24- 1 /2 23 A ll d i m e ns i o ns ar e i n in c h es . Alt. Ga s I nlet Hi gh Voltage In let Lo w V olt ag e Alt. Ga ...

  • Amana AMH* - page 8

    8 PRODUCT DESIGN MODEL TRIP POINT ID BLOWER PRESSURE SWITCH ID BLOWER PRESSURE SWITCH PART # MODEL TRIP POINT ID BLOWER PRESSURE SWITCH ID BLOWER PRESSURE SWITCH PART # AMH80453A X** -0.60 B1370142 AMH80453A X** -0.60 B1370142 AMH80703A X** -0.60 B1370142 AMH80703A X** -0.60 B1370142 AMH80704BX* * -0.60 B1370142 AMH80704BX** -0.47 B1370176 AMH80903 ...

  • Amana AMH* - page 9

    9 PRODUCT DESIGN Coil Matches: A large array of Amana ® brand coils are available for use with the AMH8 furnaces, in either upflow or horizontal applica- tions. These coils are available in both cased and uncased models (with the option of a field installed TXV expansion device). These 80% furnaces match up with the existing Amana ® brand coils a ...

  • Amana AMH* - page 10

    10 PRODUCT DESIGN Thermost at s: The following Amana ® brand Thermostats are suggested for use with the AMH8 Furnace Models: Filters: Filters are required with this furnace and must be provided by the installer. The filters used must comply with UL900 or CAN/ULCS111 standards. Installing this furnace without filters will void the unit warranty. Re ...

  • Amana AMH* - page 11

    11 PRODUCT DESIGN T winComfort™ Configuration & Operation OFF ON Blower Switch to Hi Heat Operation Blower Switch to Hi Heat Operation T-Stat S atisfied T-Stat S atisfied Delay Time ( 5 Min) Delay Time 1- 12 Min) Gas Valv e Swit ch to 2nd Stage Gas Valv e Swit ch to 2nd Stage Start Furnac e in Low Stage Start Furnac e in Low Stage Low-Heat Bl ...

  • Amana AMH* - page 12

    FURNACE SPECIFICA TIONS 12 NOTES: 1. For elevations above 2000 feet the rating should be reduced by 4% for each 1000 feet above sea level. The furnace must not be derated, orifice changes should only be made if necessary for altitude. 2. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufacturers meth ...

  • Amana AMH* - page 13

    BLOWER PERFORMANCE SPECIFICA TIONS 13 NOTES: 1 . CFM in chart is without filters(s). Filters do not ship with this furnace, but must be provided by the installer. 2 . All furnaces ship as high speed cooling. Installer must adjust blower cooling speed as needed. 3 . For most jobs, about 400 CFM per ton when cooling is desirable. 4 . INSTALLATION IS ...

  • Amana AMH* - page 14

    BLOWER PERFORMANCE SPECIFICA TIONS 14 30 40 50 60 70 80 90 1 10 12 0 100 13 0 140 150 100 90 80 70 60 50 40 30 20 10 OU TPUT B T U/HR x 10 00 BTU OUTPUT vs T EMPERA TURE RISE CHART TE M PE R AT U R E R ISE 600 CFM 700 900 100 0 1 100 1200 1400 1600 180 0 2000 2200 2400 CFM FORM ULA S BTU OUTPUT = C FM x 1.08 x RISE RISE = BTU OUTPUT 1.08 ÷ CFM 800 ...

  • Amana AMH* - page 15

    15 WIRING DIAGRAMS Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring. HIGH VOL T A GE! DISCONNECT ALL POWER BEFORE SERVICI NG OR INST A LLING THIS UNIT . M UL TIPL E POW ER SOUR CES MA Y BE P RESENT . F AILURE TO DO SO MA Y CAUSE PROP ERTY DAMAG E, PERSO NAL INJURY OR DEA TH . AMH8_CA/CB CAP ...

  • Amana AMH* - page 16

    16 WIRING DIAGRAMS Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring. HIGH VOL T A GE! DISCONNECT ALL POWER BEFORE SERVICI NG OR INST A LLING THIS UNIT . M UL TIPL E POW ER SOUR CES MA Y BE P RESENT . F AILURE TO DO SO MA Y CAUS E PROPERTY DAMAG E, PERSONAL I NJUR Y OR DEA TH. CA P BK (H I) A ...

  • Amana AMH* - page 17

    17 SCHEMA TICS HI G H VO L T AG E! DISC ONNECT ALL POWER BEFORE SERVICI NG OR INST A LLIN G THIS UNIT . M UL TIPL E POW ER SOURCES M A Y BE PR ESENT . F AILURE T O DO SO MA Y CAUS E PROPERTY DAMAG E, PERSONAL I NJUR Y OR DEA TH . TYPICAL SCHEMATIC AMH8 ____** MODEL FURNACES WR 50M56-289 INTEGRATED IGNITION CONTROL .00 05 3M K4 K2 HI HEAT COOL PARK ...

Fabricant Amana Catégorie Furnace

Les documents que nous recevons du fabricant de l'appareilAmana AMH* peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Amana
- manuels d’utilisations AMH*
- fiches produit Amana
- dépliants
- ou étiquettes-énergie Amana AMH*
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Amana AMH*.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Amana AMH*, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Amana AMH*. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Amana AMH*.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Amana AMH*, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Amana AMH* par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Amana AMH*.

Le manuel d’utilisation complet Amana, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Amana AMH* - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Amana AMH*, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAmana AMH* qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Amana AMH* - qui devraient nous aider dans les premières étapes lors de l'utilisation Amana AMH*
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Amana AMH*
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Amana AMH* dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Amana AMH*?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Amana AMH*, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Amana AMH* il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)