Français dropdown-ico

Manuel d’utilisation Barco R9010510

154 pages 8.28 mb
Télécharger

Aller à la page of 154

Summary
  • Barco R9010510 - page 1

    iCon H250/400 Owners manual (Preliminary) R9010510 R9010500 R5976992/0A 13/12/2006 ...

  • Barco R9010510 - page 2

    Product revision Software versio n: V1.00 Barco nv Presentations Noordl aan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51 E-mail: presentations.bid@barco.com Visit us at the web: www.barco.com P r i n t e di nB e l g i u m ...

  • Barco R9010510 - page 3

    Changes Barco provides this manual ’as is’ without warranty of any kind, either ex pressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Ba rco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time withou ...

  • Barco R9010510 - page 4

    The period of guarantee begins on the date of transfer of risks, in th e case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified no tice of complai nt, Barco can repair the fault or provide a replacement at its own discretion within an approp riate period. If this m ...

  • Barco R9010510 - page 5

    • Restricted Uses : The SOFTWARE is not designed or intended for use or resale in ha zardous environments requiring fail-safe perfor- mance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, or o ther devices or systems in which a malfunction of t he SOFTWARE would result i n f ores ...

  • Barco R9010510 - page 6

    T rademarks Brand and product names mentioned in this manual may be trademarks, r egistered trademarks or copyri ghts of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures. ...

  • Barco R9010510 - page 7

    Table of con tents T ABLE OF CONTENTS 1. Introducti on ......................................................................................................... 5 1.1 About this manual ........................... .................. ............... ............... ................... ............... ....... 5 1 . 2 N e t w o r k c e n t r i c v i s ...

  • Barco R9010510 - page 8

    Table of con tents 7 . 5 . 1 . 3 C o l o r ................ ................... ............... ............... ................... ............... ............... . .6 3 7 . 5 . 1 . 4 T i n t ( N T S C v i d e o s i g n a l s o n l y ) ........................... ............... ............... ................... ............. 6 4 7.5.1.5 Sharpne ...

  • Barco R9010510 - page 9

    Table of con tents 1 1 . 2 S N M P i n t e g r a t i o n. ................... ............... ............... ................... ............... ............... ......... ....... 1 3 6 1 2 . M a i n t e n a n c e...................................................................................................... 1 3 9 12.1 Cleaning the lens . ... ...

  • Barco R9010510 - page 10

    Table of con tents 4 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 11

    1. Introducti on 1. INTRODUCTION Overview • About this manual • Network centric visualization 1.1 About this manual How to use this Manual ? This manual contains 5 main parts : 1. Installation : T he mechanical setup of the projector : removing from the shipping bo x , getting the projector ready to be started. 2. Setup : Adjusting the projecti ...

  • Barco R9010510 - page 12

    1. Introduct ion 1.2 Network centric visualization Architecture : Parts and T ools • Barco Client software : runs on a client PC and allows control/diagnostics of the projector • Barco DropZone : presentation too l, running on a client PC and allowing file manipulations (launch,...) a nd sharing with the projector • Barco Server software : ru ...

  • Barco R9010510 - page 13

    2. Packagin g 2. P ACKAGING 2.1 Unpacking CEE7 European power plug to connect the power cord to the wall outlet. ANSI 73.1 1 American power plug to connect the power cord to the wall outlet. Content • 1 projector (weight ± 14 kg or 31 lbs) • 1 remote control unit RCU + 2 batteries. • 2 power cables with outlet plug type CEE7 and ANSI 73.1 1. ...

  • Barco R9010510 - page 14

    2. Packaging How to unpack the project or 1. Release the cord straps. PULL TO OPE Image 2-2 2. Remo ve the assembly from the pallet 3. Remo ve the cardboard cover 4. Remo ve the large cardboard 5. Remo ve the 8 foam parts 6. Loosen and remove the 3 screws spacers fixing the projector to the wooden board 7. Remo ve the projector from the board Save ...

  • Barco R9010510 - page 15

    3. I nstallation gui delines 3. INST ALLA TION GUIDELINES Overview • Safety warnings • Installation guidelines • Network implementation 3.1 Safety warnings W ARNING : Before installing the projector , read first the safety instructions in the safety manual (R5975258) delivered with the projec tor . Insure that the projector is installed in an ...

  • Barco R9010510 - page 16

    3. Installation guide lines Failure to take suitable precautions to protect the projector f ro m the effects of persistent and prolonged air contaminants will culmi- nate in extensive and irreversible ingrained op tical damage. At this stage cleaning of the internal optical units will be non-ef fective and impracticable. Damage of this nature is un ...

  • Barco R9010510 - page 17

    4. Installatio n 4. INST ALLA TION Overview • Battery installation in the RCU • Lens installation • Removing the lens • Lens range • Lens Formulas • Projector configuration • Positioning the projector Dimensions Dimensions are given in mm and inch ( 1inch = 25.4 mm) L eng th w ith diff eren t l enses : see t a bl e Cold air IN Cold ai ...

  • Barco R9010510 - page 18

    4. Installati on Lens Length of projecto r CLD (1.2-1.6:1) 530 mm CLD (1.6-2.4:1) 525 mm CLD (2.4-4.3:1) 550 mm QCLD (1.1-1.3:1) 580 mm QCLD (0.85:1) 610 mm 4.1 Battery installation in the RCU How to insta ll the batte ry T wo batteries are packed together with the RCU. Before u sing your RCU, install first these batteries. 1. Remo ve the battery c ...

  • Barco R9010510 - page 19

    4. Installatio n 4.2 Lens installation How to insta ll ? 1. T ake the lens out of its packing material 2. Fix the lens by placing it in the housing Image 4-3 Note: In case of a motorized lens the female jack must be in front of the male jack located in the upper-left part of the housing in the projector 3. Push carefully to lock the lens in the hou ...

  • Barco R9010510 - page 20

    4. Installati on 4.4 Lens range Overview tabl e Lens Partnumber QCLD (0.85:1) R9849860 QCLD (1.1-1.3:1) R9849850 CLD (1.2-1.6:1) R9849870 CLD (1.6-2.4:1) R9849880 CLD (2.4-4.3:1) R9849890 See the Maint enance appe ndix for mor e informa tion abo ut lens clea ning. 4.5 Lens Formulas Formulas Lenses Metric Formulas ( meter) Inch formulas (inch) QCLD ...

  • Barco R9010510 - page 21

    4. Installatio n 1 2 3 4 Image 4-6 The configurat ion should also be comm unicated to the projector. This is done in the Insta llation menu thr ough the Projector Configuration param eter . (See Setup sectio n) 4.7 Positioning the projector On-Axis projec tion Projection where the projector is positioned so as to have the centre of the lens coincid ...

  • Barco R9010510 - page 22

    4. Installati on P PD x F a b c S S B SH SW SH SW F CD=SH/2+B-A A front plate Image 4-7 16 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 23

    4. Installatio n P PD F a b c S S B SH SW SH SW F CD=B-A A front plate Image 4-8 A 100% Off-Axis position mea ns that the position of the centre of the lens is shifted by half the screen height. Never use a short throw lens in an Off-Axis installation. Shifting the lens will not guarantee optim al image quality . C AUTION : Only for projectors cont ...

  • Barco R9010510 - page 24

    4. Installati on C AUTION : Never place the projecto r on either side ! Floor Floor Image 4-9 18 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 25

    5. Connecti ons 5. CONNECTIONS Overview • Power connection • Connections • Signal connections 5.1 Power connection Power connection 1. Use the supplied powe r cord to connect the projector to the power outlet. 2. Plug the fe male power connector into the male connector at the front of the projector. Image 5-1 Power connection 5.2 Connections ...

  • Barco R9010510 - page 26

    5. Connecti ons USB RJ45 LAN Image 5-3 Point to point c onfiguration A B Image 5-4 In case of a tempo rary configuration (demo p urposes) one can use the point to point co nfiguration, the con- nection being done via RJ45 connections using a crosse d UTP cable. The connection of the server sec tio n of the projector shou ld be done in the same way ...

  • Barco R9010510 - page 27

    5. Connecti ons 5.3 Signal connections Overview • The input section • Connecting a Composite v ideo signal • Connecting an S -Video signal • Connecting an RGB signal • Connecting a Component Video signal • Connecting a D VI signal • Connecting a computer signal • The DVI output 5.3.1 The input section Input layers The input section ...

  • Barco R9010510 - page 28

    5. Connecti ons L1 LAYER 1 L1 LAYER 2 L1 LAYER 3 L1 LAYER 4 Image 5-6 Input section L1 LAYER 1 L1 LAYER 2 L1 LAYER 3 L1 LAYER 4 Image 5-7 Input with 2 RGB ana log input mod ules (ordere d with RGB Opti on) L1 LAYER 1 L1 LAYER 2 L1 LAYER 3 L1 LAYER 4 Image 5-8 Input with HDSDI/SDI module (o rdered with HDSD I/SDI Option) 22 R5976992 ICON H250/400 13 ...

  • Barco R9010510 - page 29

    5. Connecti ons 5.3.2 Connect ing a Composite vi deo signal Composite vi deo connectio n A Composite video signal is often available on a yellow cinch connector of a Camera, VCR or DVD player, i n this case you will need an adapter cable cinch/BNC to connect to Video input of the RGB board. How to connect a c omposite video s ignal 1. Con nect the ...

  • Barco R9010510 - page 30

    5. Connecti ons • 3 for the color signals R,G,B • 2 for the sync signals H (horizont al sync), V (vertical syn c) RGBS : If the source disposes of a composite sync output i.e. one wire includes the horizontal and the vertical syn c than the V BNC must not be connect ed, resulting in 4 BNC being connected (V is free). RG s B : If the source disp ...

  • Barco R9010510 - page 31

    5. Connecti ons How to connect a Component video signal 1. Con nect the 3 BNC connectors to the projector ’s RGB input DVD Pla y er Image 5- 12 In case of a “progressive scan” com ponent video source, the no tation used is PR/Y/PB 5.3.6 Connecting a DVI signal DVI Digital Visual Interface is a display interface developed in re sponse to the p ...

  • Barco R9010510 - page 32

    5. Connecti ons Image 5- 13 Left side : DVI connection on Layer 2, righ t side : DVI connection on Layer 0 Note that the 2 DVI outputs are identical and are proces sed in the same way in the projector 5.3.7 Connecti ng a computer signal How to connect a computer signal 1. Con nect the D15 connector to the projector ’s Computer input Image 5- 14 5 ...

  • Barco R9010510 - page 33

    5. Connecti ons Image 5- 15 The DVI output is at 1920x1080 (projector ’s native resolution) Image 5- 16 R5976992 ICON H250/400 13/12/2006 27 ...

  • Barco R9010510 - page 34

    5. Connecti ons 28 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 35

    6. Setup 6. SETUP Overview • RCU & Local keypad • T erminology overview • Switching on • Setting up the RCU add ress • Setting up the projector address (o nly if necessary) • Setting up the orientation • Adjusting the lens • Setup the baudrate for serial communication • Setting the server ON/O FF state • Preferences • Inst ...

  • Barco R9010510 - page 36

    6. Setup Image 6-1 Local keypad layout Remote control funct ions. This remote control includes a ba ttery powered infrared (IR) trans mitter that allows the user to control the projector remotely . This remote control is used for source selection, control, adaptation and set up . It includes automatic st oring of picture controls (Bright- ness, S h ...

  • Barco R9010510 - page 37

    6. Setup 6.2 T erminology overview Overview The following table gives an overview of the keys. Image 6-2 1 Function keys user programmable keys with functions for direct access. 2 MENU Menu key , to e nter or exit the T o olbar menu. 3 Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address ke ...

  • Barco R9010510 - page 38

    6. Setup 10 Lens control use these buttons to obtain the desired ZO OM, SHIFT , FOCUS. 11 VOL use this button to obtain the desired sound level (audio = optional) 12 Picture controls use these buttons to obtain the desired picture analog level. 13 DIGI ZOOM allows a digital Zoom of a part of the image 14 FREEZ press to freeze the projected image. 1 ...

  • Barco R9010510 - page 39

    6. Setup If the Security mod e is enabled, a tex tbox will be displayed fo r PIN code entry , see Security s e t t i n gi nt h e Installation menu 6.4 Setting up the RCU address What has to be done ? T o allow the communication between the RCU and the projector the RCU has to be programmed with the same address as the projector . This address must ...

  • Barco R9010510 - page 40

    6. Setup Common add ress/Projector address : Beside the pro jector address, th e projector disposes also of a Co mmon address which can be set to “0” or “1” (by default “0”). In other wo rds, an RCU set to address “0” will alway s control a projector regardl ess of its projector address (since it uses the co mmon address). 6.5 Setti ...

  • Barco R9010510 - page 41

    6. Setup How to change the common address ? 1. Proceed in the same way as for the projector address 6.6 S etting up the orientation What must be done ? Depending on the mechanical orientation of the projector , the projector ’s internal settings have to be adapted. The projector is shipped (default) with a table/front orientation. How to s et the ...

  • Barco R9010510 - page 42

    6. Setup How to Zoom/focus or shif t via the RCU (or keypad) 1. Press LENS ZOOM or LENS FOCUS or LENS SHIFT on the RCU 3 1 4 2 LE N S ZOOM LE N S SH IF T LE N S FOCU S V O L CONT R BRI GHTN Image 6-8 2. Use the arrow k eys to adjust 9 0 EN T ER ME N U BA C K DI G I Z OO M PH A SE PA U SE PI P L OGO Image 6-9 How to Zoom/focus or shift in the OSD ? ...

  • Barco R9010510 - page 43

    6. Setup A text box appears on the screen, follow the instructions. Image 6-1 1 Image 6- 12 The use of a sheet o f paper held in front of the screen can be useful to determine the focus plane (position for best focus) V ertical s hift range : -25% (down) to 140 %(up) Except for the Q CLD (0.85:1) : -25% (down) to 30%(up) 6.8 Setup the baudrate for ...

  • Barco R9010510 - page 44

    6. Setup 7. Press ENTER Always select the highest rate (115200) unless otherwise specified. 6.9 Setting th e server ON/OFF state Starting up The Server (desktop) will always be displayed at projector startup, it can how ever still be shut down and re-started via t he Genera l menu. During the standby state of the projector the Server can be chosen ...

  • Barco R9010510 - page 45

    6. Setup Image 6- 15 5. Press ENTER 6. A d ialog box is displayed Image 6- 16 7. Select ON or O FF for the “Projector standby stat e” setting 6.10 Preferences Overview • Language setting • Pre-programming RCU quick access keys • Automatic startup • Background 6.10.1 Language setti ng List of languages The list of selectable languages de ...

  • Barco R9010510 - page 46

    6. Setup Image 6- 17 7. Press ENTER The language is adapted and a bullet shows the active selection. 6.10.2 Pre- programming RCU quick access keys What can be done ? The 3 function keys on t op of the RCU can be associated with a particular item in one of the menus. Each function which is not password protected or does not have a key on the RCU can ...

  • Barco R9010510 - page 47

    6. Setup F1 F2 F3 ME N U BACK Image 6- 19 The menu item is stored i n the quick acces s key Factory pre-prog rammed functions -F1 : -F2 : -F3 : 6.10.3 Automati c startup What can be done ? The automatic startup allows to bypass the standby state i.e. start up without going in st andby state after switching on the projector . This means that the a u ...

  • Barco R9010510 - page 48

    6. Setup Image 6- 20 7. Press ENTER 6.10.4 Background Background setti ng The background of the projected image can be chosen to be : • iCon server: the desktop is always displayed in the background : video con tent is displayed on top of the desktop image (desktop integration). • Black : a black image is displayed in the background How to setu ...

  • Barco R9010510 - page 49

    6. Setup How to install the ser ver softw are ? 1. Th e server software is by default installed on the projector . if necessary , reinstall it from the CD . The CD containing the server software and the clien t tools are delivered with the pro jector . They can always be downloaded from the secured PartnerZo ne Web site : h ttps ://secure .barco.co ...

  • Barco R9010510 - page 50

    6. Setup A menu is dropped down Image 6- 24 projector li st: contains a projecto r and a projecto r group sub lis t 2. click on the + sign of the projector list A dialog box is displayed Image 6- 25 3. Fill in the Name, the IP address (optional) and th e Port number of TCP/IP connection Note: default port number = 9999 4. Fill in the alias Tip : ? ...

  • Barco R9010510 - page 51

    6. Setup For a point to poi nt installation the projector ’s IP address must be entered manually . Check the operating system o n the for the IP address, or contact your IT administrato r . How to add a projecto r group to the projec tor group list ? 1. Click on the white arrow A menu is displayed, image 6-24 2. Click on the + sign of the project ...

  • Barco R9010510 - page 52

    6. Setup When connect ed to a group of projectors, so me controls may be disab led. In general, controls w ill only be selected if this is the status of all projectors in the gro up. Sliders will be set to a particular value only i f this is the same on all projectors in the g roup, otherwise they will be positioned centrally w ith a dash in the va ...

  • Barco R9010510 - page 53

    6. Setup Image 6-31 Image 6-32 C AUTION : Leave these IP addresse s unchanged ! The server menu The server menu can be opened by right clicking from the server tray icon R5976992 ICON H250/400 13/12/2006 47 ...

  • Barco R9010510 - page 54

    6. Setup Image 6- 33 Start Meetings contr ol The meeting control is start ed and positioned on the desktop, through out the m eeting i t will allow to : • Accept requests interactively : a request f or a desktop sharing f rom a client PC must be accepted on the iCon server, a dial og box is displayed on the iCon asking to accept or decline the de ...

  • Barco R9010510 - page 55

    6. Setup Networking setti ngs Image 6- 35 • Port settings: it is advised to leave these settings in their default value. • Mail to field : see mail configuration in the client software • SNMP enable: allows to enable the SNMP control of the projector . The Enable write option allows to enable the client to overwrite projector settings via SNM ...

  • Barco R9010510 - page 56

    6. Setup • Enable password protection : when using a password, one must enter it when starting up the client interface • Automatically open sole document ... : when using a USB stic k, the document is automatically opened (only when one docu- ment present). When using a passw ord, the control via the previous V1.1 clie nt version will not be po ...

  • Barco R9010510 - page 57

    6. Setup • Disallow new meeting participants: New meeting participan ts will not be able to request desktop sharing or desktop control. • Disallow Launch file: Lau nching a file with the DropZone will be impossible when activating this setting, hereby preventing undesired content to be projected during a meeting. • Enable/disable desktop shar ...

  • Barco R9010510 - page 58

    6. Setup 6.15 Start up Start up T o start using the DropZone one must define the server (projector /display) to connect to. Several situations are possible. 1. The projector/display to connect to has not yet been declared in t he DropZone interface, in that case the projector/display has to be added to the DropZone list using the Add function. 2. T ...

  • Barco R9010510 - page 59

    6. Setup Following message is displayed : “Connected to <pro jectorname> ...” How to select an ex isting projec tor by its name ? 1. Click on the three suspension points to open the projector selection dialog box, image 6-44 2. Open th e listbox and select the projector . Image 6- 46 the location will also be filled (if it has been entere ...

  • Barco R9010510 - page 60

    6. Setup 54 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 61

    7. Advanced 7. ADV ANCED 7.1 The OSD Menu Structure The projector has a build in tool bar menu which allows eas y access to different parameters for projector setup. The menu is activated by pressing MENU , it contains 2 levels depending on the type of user: • Level 1: Standard user • Level 2: Advanced user Level 2 is password protected, the ad ...

  • Barco R9010510 - page 62

    7. Advanced Image 7-1 2. Key in t he desired value. Entering numeric values using the arr ow keys on the remote control 1. Press ENTER t o activate the input field. 2. Press ← or → to select the digit to be changed. Image 7-2 3. Press ↓ or ↑ to increase or decrease the value. Entering numeric val ues using the arrow key s on the local keyp ...

  • Barco R9010510 - page 63

    7. Advanced Selecting a source from the me nu bar (OSD) will always display that source in a fu ll screen mode. When selectin g a source with a different resolution (a nd/or aspect ratio) than the proje ctor ’s r esolution (and/or aspect ratio ), th e source can be shown in its na tive resolution or can be re-scaled to the projecto r’s resoluti ...

  • Barco R9010510 - page 64

    7. Advanced • Color : adjusts the level of color saturation in a P AL signal • Tint : adjusts the level of color saturation in an NTSC signal How to select the S-Vid eo input ? 1. Press MENU to a ctivate the T ool bar 2. Press ↓ to Pull down the Source Selection menu 3. Use ↑ or ↓ to se lect L2 S-V ideo Image 7-4 4. Press EN TER to confir ...

  • Barco R9010510 - page 65

    7. Advanced • Contrast • Brightness • Phase • Input balance • AutoImage : or manu al edit of the image file settings 7.3.5 PC When Select PC when you are in presence of a data s ignal of the RGB + s ync form connected to the D15 input connector of the projector. An RGB data sign al can have its sync signal added in d ifferent ways, refer ...

  • Barco R9010510 - page 66

    7. Advanced How to select th e DVI input on layer 3? 1. Press MENU to a ctivate the T ool bar 2. Press ↓ to Pull down the Source Selection menu 3. Use ↑ or ↓ to select L3 DVI Image 7-8 4. Press EN TER to confirm your choice A bullet indicates the selected composite video source which now appears on the screen. Adjustment s on a DVI signal The ...

  • Barco R9010510 - page 67

    7. Advanced 7.4.2 Freeze Freezing the image With the Freeze function, the image can be frozen. T o re start the image, reuse the Freeze function or press the FREEZE button on the remote. H o wt of r e e z et h ei m a g e? 1. Press MENU to a ctivate the T ool bar 2. Press → to select General 3. Press ↓ to Pull down the General menu 4. Use ↑ or ...

  • Barco R9010510 - page 68

    7. Advanced On the screen appears a text box. In this case the projector i s an iCon H400 Image 7- 12 6. Press MENU or B ACK to exit or to go back to the previous menu 7.5 Image Overview • Image settings • Aspect ratio • Color temperature • Film mode detection (video only) • Input balance • Automatic gain control (AGC) • Manual gain c ...

  • Barco R9010510 - page 69

    7. Advanced It is recommended to adjust the brigh tness before adjustin g the contrast. How to change the Contrast 1. Press MENU to a ctivate the T ool bar 2. Press → to select the Image item 3. Press ↓ to Pull dow n the Image menu 4. Use ↑ or ↓ to select settings 5. Press → to pu ll down the menu 6. Use ↑ or ↓ to se lect Contrast 7. ...

  • Barco R9010510 - page 70

    7. Advanced 2. Press → to select the Image item 3. Press ↓ to Pull dow n the Image menu 4. Use ↑ or ↓ to select settings 5. Press → to pu ll down the menu 6. Use ↑ or ↓ to select Color 7. Press ENTER On the screen appears now a slider box Image 7- 16 8. Use ← or → , the numeric keys on the remote, or the keypad to change the color ...

  • Barco R9010510 - page 71

    7. Advanced On the screen appears now a slider box Image 7- 18 8. Use ← or → , the n umeric keys on the remote, or the keypad to change the Sh arpness 7.5.1.6 Gamma Gamma adjustment The gamma parameter d etermines the way your encoded (luminance) signal is transformed into brightness at the output of th e projector . A correct gamma setting wil ...

  • Barco R9010510 - page 72

    7. Advanced Image 7- 20 How to adjust t he Phase 1. Press MENU to a ctivate the T ool bar 2. Press → to select the Image item 3. Press ↓ to Pull dow n the Image menu 4. Use ↑ or ↓ to select settings 5. Press → to pu ll down the menu 6. Use ↑ or ↓ to select Phase 7. Press ENTER On the screen appears now a slider box Image 7- 21 8. Use ...

  • Barco R9010510 - page 73

    7. Advanced On the screen appears now a slider box Image 7- 22 8. Use ← or → , the num eric keys on the remote, or the keypad to change the Noise Reduction 7.5.2 Aspect rati o Aspect rat ios The standard aspect ratio used in broadcast television is the 4:3 ratio. However, most of the DVD sources use nowadays the wide screen 16:9 or even the Cin ...

  • Barco R9010510 - page 74

    7. Advanced 4:3 16:9 2.35:1 16:9 anamorphic 2.35:1 anamorphic Projector setting Source 4:3 16:9 5:4 Image 7- 25 Possible aspect ratio settings and their effect on differen t sources We can conclude that the thumb rule for DVD projection is to alw ays leave the projector in 4:3 format except when dealing with anamorphic sources where the 16:9 settin ...

  • Barco R9010510 - page 75

    7. Advanced Image 7- 26 4. Use ↑ or ↓ to select Aspect ratio 5. Use → open the Aspect ratio menu 6. Use ↑ or ↓ to select the desired ratio 7. Press EN TER to confirm The aspect ratio settings are grey ed out in case the Show native resolution or the Full screen rep resentation settin g is enab led. How to set a custom A spect ratio ? 1. P ...

  • Barco R9010510 - page 76

    7. Advanced 7.5.3 Color temperature What can be done ? The color temperature can be selecte d according to the type of source: There are 4 different preset color temperatures: • Projector white • computer : 9300 K • Video : 6500 K • Film : 5400 K • Broadcast : 3200 K These calibrated presets can be selected and will provide optimum color ...

  • Barco R9010510 - page 77

    7. Advanced A slider box for the red custom setting is displayed as we ll as a wizard text box in the lower part of the screen. Image 7- 30 Follow the instructions on the wizard text box. Image 7-31 Image 7-32 7.5.4 Film mode detecti on (video only) What can be done ? Some sources like common DVD material are derived from cinema 24 Hz s ources (2/2 ...

  • Barco R9010510 - page 78

    7. Advanced Image 7-34 The film mode detection insures that these converted signals are shown without artefact s, especially motion artefacts due to bad de-inte rlacing. This fu n ction may cause undes ired effects on standard sources, th erefore it can be disabled (OFF) at any time Enabling/disabl ing the fil m mode detection 1. Pres s MENU to act ...

  • Barco R9010510 - page 79

    7. Advanced B Black level 0.7V Image 7-36 Black level ∆ G ∆Β ∆ R R G B Image 7-37 The objective of i nput ba lancing The objective in input balancing is to “set” the same black level and the same white level for the three colors of a particular input source. Black level setting : brightness White level setting : contrast The same absolut ...

  • Barco R9010510 - page 80

    7. Advanced An alternativ e to a full screen White/b lack pattern is the stan dard gray scale pattern, the white bar will be u sed for white ba lance and the blac k bar for bl ack bala nce. Image 7-39 It is not necessary to adjust the black balance. Its value is automatically set to an optim al value (512). Performing White input bal ance 1. Select ...

  • Barco R9010510 - page 81

    7. Advanced 10. Adjust the Green white level (gain) until bright spots appear on the white part of the image 1 1. Adjust the Blue white level (gain) until bright spots appear on the white part of the image 12. Adjust the Red white level (gain) until bright spots appear on the white part of the image The projected image should now be noisy neutral g ...

  • Barco R9010510 - page 82

    7. Advanced 7.5.7 Manual gain contr ol What can be done ? Beside the AGC there is the possibility to manually set the gain of the incoming video signal. When the AGC is enabled (ON), the manual setting does not affect the gain, AGC must therefore be disabled. The manual gain control must be done on an external pattern with white areas (grey scale b ...

  • Barco R9010510 - page 83

    7. Advanced Image 7- 45 5. Press ENTER A text box is displayed Image 7- 46 7.6.2 Lamp mode Single mode The projector will always switch to the lamp with the shortest r untime when the difference between the runtimes of lamp 1 and lamp 2 reaches 100 hours , switching from one lamp to another happe ns only at switching on of the projector and not dur ...

  • Barco R9010510 - page 84

    7. Advanced Image 7- 47 Single mode operation : switching princip le Dual mode Both lamps are working at the same time. When one lamp fails, the projector continues the projection usin g the remaining lamp. Again the lamp error is logged and shown on the screen. How to select th e lamp mode ? 1. Press MENU to a ctivate the T ool bar 2. Press → to ...

  • Barco R9010510 - page 85

    7. Advanced When switching from th e dual mode to the single mode the lamp with the longest runtim e is switched off. If the runtimes are equal (if the projecto r has always been operated in dual mode) then lamp 1 is switc hed out. When switch ing to single mod e, returning to the du al mode will not be p ossible in the first 60 sec onds, Dual in t ...

  • Barco R9010510 - page 86

    7. Advanced How to reset the l amp runtime ? 1. Press MENU to a ctivate the T ool bar 2. Press → to s elect the Lamp item 3. Press ↓ to Pu ll down the Lamp menu 4. Use ↑ or ↓ to se lect Reset runtime 5. Press → to pu ll down the menu 6. Use ↑ or ↓ t os e l e c tt h el a m pt ob e r e s e t Image 7- 51 7. Press ENTER A dialog box is di ...

  • Barco R9010510 - page 87

    7. Advanced A lamp failing to startup will b e noticed by a low light output of the projector since the projector goes in single lamp mode. In case of a lamp error contact the local Barco authorized technician How to clear the lamp error ? 1. Press MENU to a ctivate the T ool bar 2. Press → to s elect the Lamp item 3. Press ↓ to Pu ll down the ...

  • Barco R9010510 - page 88

    7. Advanced A dialog box is displayed Image 7- 56 6. Use ← or → , the numeric keys on the remo te, or the keypad to change the runtime warning setting. W ARNING : Lamp runtim e reset as well as the lamp replacement can only be done by a Barco authorized technician. 7.7 Image files Overview • Introduction to Image files • Load file • Force ...

  • Barco R9010510 - page 89

    7. Advanced 7.7.2 Load file When to lo ad a file ? In some cases the user wants a particular file to be used for the display of a particular source. In this case the user should load the desired file from the image files menu. The load file option will allow the user to choose between several files corresponding more or less to the active source sp ...

  • Barco R9010510 - page 90

    7. Advanced What to do if the image is not pe rfect ? If the displayed image is not correct after AutoImage or after selecti ng the best fitting file, go to the Edit menu, select the active file and change the settings. 7.7.3 Forced file load Forced f ile load In some cases the user wants only one particular file to be loaded for a particular input ...

  • Barco R9010510 - page 91

    7. Advanced 7.7.4 Auto Image What can be done ? AutoImage creates the best suited image file for the c onnected source. It calculates/measures se veral source parameters : • T otal pixels per line • Start pixel • Phase • Contrast/Brightness levels Auto Image works only for d ata images. The measure of the total number of pixels per line can ...

  • Barco R9010510 - page 92

    7. Advanced 7.7.5 Edit file What can be done with the Edit file menu ? The Edit file menu makes it possible to change the settings of th e file according to the real settings of the connected source. Consult the source specifications before entering the data. only the active file can be edited How to edit a file ? 1. Press MENU to a ctivate the T o ...

  • Barco R9010510 - page 93

    7. Advanced Which items can be adjus ted ? The following items can be adjusted : • Active horizontal pixels • Horizontal start in pixels • Horizontal period in ns • Active verti cal lines • V ertical start in lines Advanced vide o settings The advanced button enables the advanced settings for a video source. Image 7-64 video signal video ...

  • Barco R9010510 - page 94

    7. Advanced Image 7- 67 It is recommended to use the d efault values. 7.7.6 Save as (creat e a custom file) Creating a custom file When the loaded file is a standard file there is a possibility of saving it as a custom file (= creating a custom file) , this is done with the save as function. T he saved file will always be a custom file (saved i n t ...

  • Barco R9010510 - page 95

    7. Advanced 3. Press ↓ to Pull down the Image files menu 4. Use ↑ or ↓ to se lect Rename Image 7- 70 5. Press ENTER A dialog box is displayed Use ← or → , ↓ or ↑ the numeric keys on the remote, or the keypad to edit and change the values, conf irm with ENT ER. Image 7- 71 7.7.8 Copy Copy a file The copy function allows to copy a file ...

  • Barco R9010510 - page 96

    7. Advanced Image 7- 73 6. Use ↑ or ↓ to select the file to be copied 7. Press ENTER The file name is copied in the edit field 8. Use the keys on the remote to change the name of the destination file 7.7.9 Delet e How to delete a fi le ? 1. Press MENU to a ctivate the T ool bar 2. Press → to select the Image files item 3. Press ↓ to Pull do ...

  • Barco R9010510 - page 97

    7. Advanced 7. Press ENTER The selected file is deleted and is removed from the list 7.8 Display setup Overview • Dynacolor™ • Brilliant Color TM mode • Full screen synchronous representation • T ext box • Menu bar position • Status bar position • Sliderbox position 7.8.1 Dynacol or™ What can be done? DynaColor™ will eliminate c ...

  • Barco R9010510 - page 98

    7. Advanced Due to the tolerance on optical components the x, y values of this color gamut of each projector will dif fer . Image 7- 78 The color gamut of each project or will dif fer When working with a multichannel se tup, these color differences between different projectors can be smoothed out by matching the color gamuts of the diff erent proje ...

  • Barco R9010510 - page 99

    7. Advanced G1 G2 R1 R2 B1 W1 0 x y .1 .2 .3 .4 .5 .6 .7 .1 .2 .3 .4 .5 .6 .7 .8 B2 W2 Gc Wc Yc Rc Mc Bc Cc Image 7- 80 The Comm on Color Gam ut R1 Red projec tor 1 R2 Red projec tor 2 G1 Green Projector 1 G2 Green Projector 2 B1 Blue Projector 1 B2 Blue Projector 2 W1 White Projector 1 W2 White Projector 2 Rc Red Common Color Gamut Gc Green Common ...

  • Barco R9010510 - page 100

    7. Advanced Image 7- 81 The Dynacolor dialog box will be displayed. Image 7- 82 5. Push the cursor key ← or → select enable/disable and then ENTER . 94 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 101

    7. Advanced Dynacolor™ g (Light Output) V alue The value g in the Dynacolor™ interface represents a relative light output. g=1 is the maximum available light output. Assume we have a projector. L=1 in the Dynacolor™ interface will correspond with a ’maximum f ull white light’ output of x Lum ens. The Dynacolor™ Interfa ce Following para ...

  • Barco R9010510 - page 102

    7. Advanced Basic Dynaco lor™ Adjustment We assume we have a basic setup with 2 pro jectors, the Dynaco lor™ adjustment is done by using only the Dynacolor™ menu: 1. Enable D ynacolor™ on both projectors. 2. Assume th e first projector has the following measured values. Image 7- 83 3. Assume the seco nd projector has the following measured ...

  • Barco R9010510 - page 103

    7. Advanced Image 7- 84 R5976992 ICON H250/400 13/12/2006 97 ...

  • Barco R9010510 - page 104

    7. Advanced 4. We start by setting both projectors to the common red coordinate. Tip : Draw a quick sketch of both gamuts as a graphical help. 650 640 310 320 330 660 R1 R2 Image 7-85 Red coordin ates for both proje ctors 5. Display the internal color bar pattern on both projectors. 6. In the desired values, adjust the red coordinate to a common va ...

  • Barco R9010510 - page 105

    7. Advanced Select a coordinate that is present in the common gamut e.g. with the desire d values for red set to x=633 and y= 328. 650 640 310 320 330 660 R1 R2 Rc Image 7- 87 Select a coo rdinate that is p resent in the com mon gamut 7. Rep eat step 5 to 6 for all coordinates on both projectors. Both projectors will now operate within the same col ...

  • Barco R9010510 - page 106

    7. Advanced 5. Put the slider box on ’0’ (Brilliant color disabled ) or on ’1’ (Brilliant color enabled) Image 7- 89 7.8.3 Full s creen synchronous repre sentation What can be done ? In the full screen mode, the projector will always try to lock on the input source. Some monitors (conn ected on the DVI out put of the projector) may fail to ...

  • Barco R9010510 - page 107

    7. Advanced Image 7- 91 7. Press ENTER 7.8.5 Menu bar position What can be done ? The menu tool bar can be centered vertically , the range being from top of the screen to the m iddle of the screen. T his can be useful in applications where the top image content is not displayed. How to center the menu ? 1. Press MENU to a ctivate the T ool bar 2. P ...

  • Barco R9010510 - page 108

    7. Advanced Image 7- 93 5. Press ENTER 6. Use ↑ or ↓ to position the sta tus bar 7.8.7 Slider box positio n What can be done ? The slider box can be displayed anywhere on the screen, the position can be set in this menu. How to reposit ion the slide r box? 1. Press MENU to a ctivate the T ool bar 2. Press → to se lect the Display setup item 3 ...

  • Barco R9010510 - page 109

    8. Network centr ic operation s 8. NETWORK CENTRIC OPERA TIONS Overview • Introduction • Control • Configuration • Remote desktop sharing (virtual meeting) • The Web client 8.1 Introduction Overview • Network architectu re • Network functionality • iCon server specifications 8.1.1 Network architectu re SBC Single Board Computer, GUI ...

  • Barco R9010510 - page 110

    8. Network cent ric operat ions WAN LAN RM : Remote control & Management P : projection area M2 : Meeting room M1 : Meeting room 1 A : SERVER R : remote meeting attendee V : streaming video data M3 : Large conference room Image 8-1 T ypical iQ Pro ne twork architecture A server RM Remote Control and Management M1 Meeting room 1 M2 Meeting room ...

  • Barco R9010510 - page 111

    8. Network centr ic operation s The network centric p rojector may be configu red in the same way as a sta ndard PC to suppo rt : - SNMP service : provides diagnostics, basic co ntrol via SNMP messaging - Microsoft Exchan ge services: for scheduling of p rojector tasks. - Web client : offers an alterna tive to the Client so ftware through a user-fr ...

  • Barco R9010510 - page 112

    8. Network cent ric operat ions LAN A : facility manager's desk B : projection areas ... Image 8-3 control & management of networ k centric projector (s) A facility manager ’s desk B projector area What ca n be cont rolled ? Almost ever y menu item can be con trolled through the control manager • standby on/off •l a m p m o d e • s ...

  • Barco R9010510 - page 113

    8. Network centr ic operation s Image 8-4 The control interface : the general sub screen is active (see tool bar) 8.2.2 How to use the control manager? How to us e the control m anage r? 1. Cho ose the sub screen by clicking on the desired item on the tool bar in the upper part of the control interface The active sub screen is indicated with a blue ...

  • Barco R9010510 - page 114

    8. Network cent ric operat ions Image 8-5 The source selection scr een How to select a source ? 1. Click on show all or show detected Depending on the option (show all/detected) selected, a list is displa yed. In case show all is selected, a list of all possible sources is d isplayed, signal presence is indicated with an orange d ot. When show dete ...

  • Barco R9010510 - page 115

    8. Network centr ic operation s Image 8-6 PiP screen How to perform operations on a PiP layout As an example, let us choose a personal (non preset) layout, add a window , reposition the windows, and save the layout under a different name. 1. Click on one of the check boxes to choose a layout Choose a personal layout Image 8-7 R5976992 ICON H250/400 ...

  • Barco R9010510 - page 116

    8. Network cent ric operat ions The PiP screen (as well as the projected layout) is updated Image 8-8 This layout contains one window being an RGBHV Data source 2. Click on the Add window butto n Note: if the layout already contains 4 window , it will be impossible to add a new one. In that case a window is displayed, image 8-9 Image 8-9 A dialog b ...

  • Barco R9010510 - page 117

    8. Network centr ic operation s The window is added to the layout. Image 8-1 1 4. When entering the PiP screen the cursor is replaced by a hand, Click on the window to be repositioned. The window is surrounded by a white frame. 5. Drag the window to the desired position. 6. Place the cursor on one of the corners of the window to be re sized. A doub ...

  • Barco R9010510 - page 118

    8. Network cent ric operat ions A dialog box is displayed. Image 8- 13 2. Select t he layout to be imported. For more informa tion on Picture in Picture see the P iP chapter . 8.2.6 Image settings What can be done ? • General settings • Color temperature • Geometry General i mage settin gs 1. Click on Imag e settings menu in the tool bar to d ...

  • Barco R9010510 - page 119

    8. Network centr ic operation s Use the checkbox to define a coarse or a fin e setting. Click on th e Filmmode button to enable o r disable the filmmode. Color temperat ure preset settin gs 1. Click on Image settings menu in the tool bar to drop down the subme nu. 2. Click on color temp , image 8-14 3. Click on the desired preset color temperature. ...

  • Barco R9010510 - page 120

    8. Network cent ric operat ions a dialog box is displayed. Image 8- 19 3. Use the bu ttons to zoom or pan. Tip : Use the buttons to choose small, medium or large adjustment steps. Each click changes the setting. 4. Click on the desired aspect ratio and resolution handling mode. 8.2.7 Advanced cont rol Overview • Lens adjustments •O p t i o n s ...

  • Barco R9010510 - page 121

    8. Network centr ic operation s Image 8- 21 Tip : Use the buttons to choose small, medium or large adjustment steps. Each click changes the setting. 8.2.7.2 Option s How to start up the options menu ? 1. Click on the Adva nced menu in the tool bar to drop down the subm enu. 2. Click on Options . Image 8- 22 The adva nced Opti ons screen How to set ...

  • Barco R9010510 - page 122

    8. Network cent ric operat ions Image 8- 23 2. Click on Apply to perform AutoImage. Lamp runtime warnings startu p settings 1. Fill in the lamp runtime warning time. Image 8- 24 2. Click on startup screen to enable the startup screen. 3. Click on Auto Startup to enable automatic startup. A blue spot indicates that th e function is enabled. 8.3 Conf ...

  • Barco R9010510 - page 123

    8. Network centr ic operation s • daily : E-mail is sent every day , the time can be set • weekly: the day can be set with a calendar • on warning : a E-mail is sent whenever a warning is generated by the projector 8.3.2 E-mail confi guration How to configure the E-ma il ? 1. Click on C onfiguration in the toolbar 2. Click on Mail Config to o ...

  • Barco R9010510 - page 124

    8. Network cent ric operat ions Image 8- 27 8.3.3 Projector Fir mware Upgrade What can be done ? The client software allows to do a n upgrade of the projector ’s firmware. The upgrade is done with a binary file (extension = “.bin” ) which is sent to the projector using the LAN c onnection. Single projector as well as multiple projector (group ...

  • Barco R9010510 - page 125

    8. Network centr ic operation s Image 8- 29 5. Press the Upgrade button on the upgrade screen to start the opera tion The information screen w ill show the progress of the operation. If the download doesn ’t succeed please contact Barco 8.4 Remote desktop sharing (virtua l meeting) What can be done ? The remote desktop sharing in the DropZone all ...

  • Barco R9010510 - page 126

    8. Network cent ric operat ions IQ Pro Server desktop Control 1 1 1 2 3 2 3 3 2 Image 8- 30 Virtu al Meeting 1 f orward control 2 r elease control 3 r equest control How to perform remote de sktop sharing ? 1. Click on t he middle button 120 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 127

    8. Network centr ic operation s The middle button indicates the activation of the remote The desktop is displayed on the local PC monitor . Image 8- 31 remote des ktop sharing in ca se of a PowerPoint TM presentation How to take (mouse and keyboard)Cont rol over the deskt op ? 1. Click on the Control menu The Control menu is displayed Image 8- 32 2 ...

  • Barco R9010510 - page 128

    8. Network cent ric operat ions The Control menu is displayed Image 8- 33 2. S elect the Release Control item The desktop remote control can now be requested by someone else. How to forward control over the desktop ? 1. Click on the Control menu The Control menu is displayed Image 8- 34 2. S elect the Forward Control item A pop up menu shows the me ...

  • Barco R9010510 - page 129

    8. Network centr ic operation s Image 8- 35 Web inte rface What can be done ? The possibilities are mainly the same as on the client software. The web interface allows a user friendly way to manage t he projector/display , its use being straightforward and similar to the client interface (ref). Requirements for the use of th e Web clien t Some comp ...

  • Barco R9010510 - page 130

    8. Network cent ric operat ions 124 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 131

    9. General guidel ines on Network Conf igurati on 9. GENERAL GUIDELINES ON NETWORK CONFIGURA TION Overview • General Network • The Internet and Web services The insta llati on of the i Q Pro in a Loc al Area Ne twork mus t be done in the same wa y as the i nstal lation o f a standard PC in that particular netwo rk meaning that the same rules an ...

  • Barco R9010510 - page 132

    9. General guidel ines on Network Conf igurati on Image 9-1 system tray Image 9- 2 server settings dialog box For more info, see "SNMP services", page 135 Microsoft Exchange and Outlook T o enable control via the Microsoft Exchange integration, you need to install, enable and configure t he IQProEXCH module. T o enabl e control from Micro ...

  • Barco R9010510 - page 133

    10. Exchange 10. EXCHANGE Introduction Some parameters values are installation dependent, and are show n here as an example. Y ou may need assistance from yo u network administrator , IT Manager or MIS help desk to obtain the settings or to co nfigure the projector for you, since this is a task description targeted to ‘Administrators’ an d need ...

  • Barco R9010510 - page 134

    10. Exchange For security reasons, y ou will probably not want to ma ke the projector account part of one of the administrator groups. 2. Enable the acco unt to be used by the “iQ Pro Exchange Integration” service 3. In the Tree of the “Local Security Settings” application, navigate t o Security Settings->Local Policies->User Right As ...

  • Barco R9010510 - page 135

    10. Exchange Panel/Administrative T ools/ Local Security Settings/Security Settings/Lo cal Policies/User Right Assignment. In the list, add the user to the entry “ Log on as a service ” 3. Th e log file contains “ Could not log on with Profile ’M S Exchange Setting s ’” Make sure the profile exists. T o ch eck this, log in to the projec ...

  • Barco R9010510 - page 136

    10. Exchange Overview of the commands •O N •S T A N D B Y • P AUSE • P AUSE ON • P AUSE OFF •L O G O •L O G O O N •L O G O O F F • SWITCH SOURCE •S W I T C H L A Y O U T • LAUNCH A TT ACHMEN T • STORE A TT ACHMENT •S T O R E file name •S T O R E F I L E file path • LAUNCH filenam e • LAUNCH FILE filepath • DELETE f ...

  • Barco R9010510 - page 137

    10. Exchange Image 10-3 10.2.2 Example Schedule projector ta sks in Microsoft Outlook 20 00 following tasks are scheduled: Image 10-4 1. store a ttachment at 12:30 (The attached file is iQ_Pro_brochure.pdf) 2. turn the projector on at 13:00 and launch a different attached file 3. show the logo from 14:29 to 14:31 to hide the killing of the applicat ...

  • Barco R9010510 - page 138

    10. Exchange Image 10-5 The form contains the functionality that a normal user sh ould be able to use without consulting the documentation. The attachments, date and time fields must be edited in the “Appointment” tab. Choosing items from the drop-dow n boxes fills in the subject. By default, the layouts “Full-screen” and “2by2 raster” ...

  • Barco R9010510 - page 139

    10. Exchange Image 10-7 10.2.4 Folder form Folder form Alternatively , the form can be installed for the Calendar folder only , by following the proce dure described below How to configure a fo lder form 1. In outlook, right-click on the “Calendar” icon in the “Outl ook Sh ortcuts” tab in the “Outlook Bar” to open the “Properties” p ...

  • Barco R9010510 - page 140

    10. Exchange Image 10-10 10.2.5 Limi tations and known “problems” Overlapping t asks When launching 2 attachments with overlapping times it is possible for the application to exi t at the end of the first period. For example, let’s say we try to display PRES1.PPT from 12:00 to 13: 30, and PRES2.PPT from 13:00 to 14:30, it is possible for BOTH ...

  • Barco R9010510 - page 141

    11. SNMP services 1 1. SNMP SERVICES Introduction Some parameters values are installation dependent, and are show n here as an example. Y ou may need assistance from yo u network administrator , IT Manager or MIS help desk to obtain the settings or to co nfigure the projector for you, since this is a task description targeted to ‘Administrators? ...

  • Barco R9010510 - page 142

    11. SNMP services 3. In the “Security” tab, the default Community is called ‘public’ and is read-only . Y ou may wa nt to give read-write permission to ‘ publi c’ (not recommended) or crea te a ‘private’ community with read-write permissions. 4. In the Cont rol Server , enable the SNMP support, and optionally , enable read-write sup ...

  • Barco R9010510 - page 143

    11. SNMP services Command Ty p e POWERSUPPL YERROR READ LAMPERROR READ PCST A TEPROJECTORON READ/WRITE PCST A TEPROJECTORST ANDBY READ/W RITE PCST A TE READ/WRITE R5976992 ICON H250/400 13/12/2006 137 ...

  • Barco R9010510 - page 144

    11. SNMP services 138 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 145

    12. Maintenance 12. MAINTENANCE 12.1 Cleaning t he lens T o minimize the possibility o f damage to optical coating s, or scratches to lens su rfaces, we have develo ped recommendations for clean. FIRST , w e recommend you try to rem ove any material from the lens by blow ing it off with clean, dry deionized air. DO NOT us e any liquid to clean the ...

  • Barco R9010510 - page 146

    12. Maintenance 140 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 147

    13. Image files 13. IMAGE FILES 13.1 Image files T able overvi ew The following standard image files are pre-programmed in the projector . Name 1 Resolution 2 Fvert Hz 3 FHor kHz 4 Fpix MHz 5 Ptot 6 Pact 7 Ltot 8 Lact 9 1600@48V 1600x600i 48,040 62,500 135,000 2160 1600 651 600 1600@60V 1600x900 60 56 11 9 2128 1600 932 900 1600@192 1600x600 96 63 ...

  • Barco R9010510 - page 148

    13. Image files Name 1 Resolution 2 Fvert Hz 3 FHor kHz 4 Fpix MHz 5 Ptot 6 Pact 7 Ltot 8 Lact 9 hd@24sf 1950x540 48,000 27,000 74,000 2 750 1950 562 540 hd@25i 1920x540 50,000 28,125 74,000 2 640 1920 562 540 hd@25p 1920x1080 25,000 28,125 74,000 2 640 1920 1 125 1080 hd@30p 1920x1080 30,000 33,750 74,000 2 200 1920 1 125 1080 hd@60p 1280x720 60,0 ...

  • Barco R9010510 - page 149

    13. Image files Name 1 Resolution 2 Fvert Hz 3 FHor kHz 4 Fpix MHz 5 Ptot 6 Pact 7 Ltot 8 Lact 9 PC98_3 1 120x750 60,000 50,000 78,5 69 1571 11 2 0 833 750 QXGA@56 2048x1536 56 89 247 2784 2048 1586 1536 QXGA@60 2048x1536 60 95 267 2800 2048 1589 1536 S1 152@66 1 152x900 6 6,004 61,846 94,500 1528 11 5 2 937 900 S1 152@76 1 152x900 7 6,637 71,809 1 ...

  • Barco R9010510 - page 150

    13. Image files Name 1 Resolution 2 Fvert Hz 3 FHor kHz 4 Fpix MHz 5 Ptot 6 Pact 7 Ltot 8 Lact 9 SXGA_@72_2 1280x1024 72 76,970 130,080 1690 1280 1069 1024 SXGA_@75 1280x1024 75 79,974 134,997 1688 1280 1066 1024 SXGA_@76 1280x1024 76 81,103 134,955 1664 1280 1066 1024 SXGA_@85 1280x1024 85 91,149 157,506 1728 1280 1072 1024 SXGA_L 1280x1024 60 62, ...

  • Barco R9010510 - page 151

    13. Image files Name 1 Resolution 2 Fvert Hz 3 FHor kHz 4 Fpix MHz 5 Ptot 6 Pact 7 Ltot 8 Lact 9 VIDEO625 1024x278i 25,000 15,625 31,984 1310 1024 313 278 WSXGA@60 1600x1024 60 64 137 2144 1600 1060 102 4 WSXGA+@60 1680x1050 60 79 178 2272 1680 1304 105 0 WUXGA@60 1920x1200 60 75 194 2592 1920 1245 120 0 WUXGA_2@60 1920x1200 60 89 234 2624 1920 149 ...

  • Barco R9010510 - page 152

    13. Image files 146 R5976992 ICON H250/400 13/12/2006 ...

  • Barco R9010510 - page 153

    Index INDEX A address 33 RCU 33 Address 34 Project or addre ss 34 Advanced 55 AGC 75 Auto Image 85 automatic startup 41 B brightness 63 brilliant color 99 C Cleaning 139 Lens 139 color 63 configuration 14, 46 server 46 connection 23–24, 26 Component video 24 computer 26 RGB 23 S-Video 23 connections 21 input 21 signal 21 Connections 19 contrast 6 ...

  • Barco R9010510 - page 154

    Index M Maintenance 139 manual 5 use 5 menu 55 Menu 34, 55, 67, 71, 86 , 88–90, 100 Image files menu 86, 88–90 copy file 89 custom file 88 delet e file 90 edit file 86 rename file 8 8 Image menu 67, 71 aspect ratio 67 film mode detection 71 Installation 34 projector address 34 Installation menu 100 text box 100 Using the dialog boxes 55 menu ba ...

Fabricant Barco Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilBarco R9010510 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Barco
- manuels d’utilisations R9010510
- fiches produit Barco
- dépliants
- ou étiquettes-énergie Barco R9010510
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Barco R9010510.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Barco R9010510, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Barco R9010510. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Barco R9010510.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Barco R9010510, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Barco R9010510 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Barco R9010510.

Le manuel d’utilisation complet Barco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Barco R9010510 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Barco R9010510, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lBarco R9010510 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Barco R9010510 - qui devraient nous aider dans les premières étapes lors de l'utilisation Barco R9010510
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Barco R9010510
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Barco R9010510 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Barco R9010510?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Barco R9010510, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Barco R9010510 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)