Manuel d’utilisation Briggs & Stratton 500Z - 26

16 pages 0.97 mb
Télécharger

Aller à la page of 16

Summary
  • Briggs & Stratton 500Z - 26 - page 1

    1/2008 1 5101454 Rev. IR TP 300-7368-IR-ZT-N Dealer Setup & Adjustment Instructions 500Z - 26 HP Briggs & Stratton 48” Mower Deck T ABLE OF CONTENTS: SETUP PROCEDURES Quick Setup List ................................................................2 Uncrating ............................................................................3 Ba ...

  • Briggs & Stratton 500Z - 26 - page 2

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 2 Quick Setup List - P age Setup Procedure Steps to P erform 3 Uncrating ❏ Remov e Crate & Banding. ❏ Disengage T ransmission Release Le v ers. ❏ Release P arking Brake and Roll T r actor forw ard off skid. ❏ Engage T ransmission Release Le v ers. 3 Battery Installation ❏ Instal ...

  • Briggs & Stratton 500Z - 26 - page 3

    500Z 26HP - 48” Mower Dec k 1/2008 3 TP 300-7368-IR-ZT-N Uncrating 1. Using a reciprocating utility saw or equivalent, cut the crate away from the bottom skid. Remove the crate. Remove the shrink-wrap plastic. 2. Cut the nylon banding from the front of the frame and the rear of the bumper. 3. Pull both transmission release levers (A, Figure 1) ba ...

  • Briggs & Stratton 500Z - 26 - page 4

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 4 T ractor Assembl y Install Gr ound Speed Control Le vers 1. Install the ground speed control levers (A, Figure 3) onto the control lever base (B) using the 5/16-18 x 3/4” bolts, 5/16” lock washers and 5/16” flat washers (C, D & E). Prior to tightening the bolts, align the handles ...

  • Briggs & Stratton 500Z - 26 - page 5

    500Z 26HP - 48” Mower Dec k 1/2008 5 TP 300-7368-IR-ZT-N Chec k Fluid Le vels Chec k the Engine Oil Level 1. Use the engine oil dipstick (A, Figure 5) to check the engine oil level. If necessary add engine oil. Check the engine manufacturer’s owner’s manual for the oil recommendations. Chec k / Fill T ransmission Oil Oil Type: 20W-50 conventi ...

  • Briggs & Stratton 500Z - 26 - page 6

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 6 Chec k the Mower Assembl y Chec k T or que - Mower Blades 1. Park the machine on a flat, level surface and engage the parking brake. 2. Lock the deck lift pedal in the 4-1/2” (11,47 cm) position. 3. Check that blades are installed with the tabs pointing up toward the deck as shown in Figu ...

  • Briggs & Stratton 500Z - 26 - page 7

    500Z 26HP - 48” Mower Dec k 1/2008 7 TP 300-7368-IR-ZT-N Chec k Deck Rod Timing 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 40 psi (2,76 bar). 2. To check the lift rod timing, measure and record the distance between the ...

  • Briggs & Stratton 500Z - 26 - page 8

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 8 Figure 10. 2 x 4 Locations Figure 11. Hanger Chain Adjustment Dec k Leveling Adjustment NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted. 1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. ...

  • Briggs & Stratton 500Z - 26 - page 9

    500Z 26HP - 48” Mower Dec k 1/2008 9 TP 300-7368-IR-ZT-N Chec k Deck Drive Belt 1. Lower the mower deck to its lowest cutting position. 2. Remove the mower deck guards. 3. Make sure the V-side of the belt runs in the pulley grooves (Figures 14). 4. If the belt is not properly seated, use a 1/2” breaker bar, and place the square end in the squar ...

  • Briggs & Stratton 500Z - 26 - page 10

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 10 Lubrication Lubricate the unit at the locations shown in Figure 15 through18 as well as the following lubrication points. Grease: • front caster wheel axles and yokes • deck lift pivot blocks • mower deck spindles • mower deck idler arm Use grease fittings when present. Disassemble ...

  • Briggs & Stratton 500Z - 26 - page 11

    500Z 26HP - 48” Mower Dec k 1/2008 11 TP 300-7368-IR-ZT-N Figure 19. Adding Fuel A. Fuel Cap A Adding Fuel To add fuel: 1. Remove the fuel cap (A, Figure 19). 2. Fill the tank to about 1-1/2” (3,81 cm) of the bottom of the filler neck. This will allow for fuel expansion. NOTE: Do not overfill. Refer to your engine manual for specific fuel recom ...

  • Briggs & Stratton 500Z - 26 - page 12

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 12 P erf orm the Safety Chec ks Functional T ests 1. Check the tractor for loose bolts, screws, nuts, etc. 2. Start the engine and check all the controls for proper operation: ground speed control levers, parking brake, throttle cable, electric PTO clutch, etc. 3. Stop the engine and check fo ...

  • Briggs & Stratton 500Z - 26 - page 13

    500Z 26HP - 48” Mower Dec k 1/2008 13 TP 300-7368-IR-ZT-N Adjustment Pr ocedures Seat Adjustment See Figure 20. The seat can be adjusted forward and backward. Move the seat adjustment lever towards the left, position the seat as desired, and release the seat adjustment lever to lock the seat into position. A Figure 20. Seat Adjustment A. Seat Adj ...

  • Briggs & Stratton 500Z - 26 - page 14

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 14 Return-T o-Neutral Adjustment To determine if it is necessary to adjust the neutral return, perform the following steps. 1. Disengage the PTO, engage the parking brake and turn off the engine. 2. Move the ground speed control levers into the operating position, pull levers rearward and rel ...

  • Briggs & Stratton 500Z - 26 - page 15

    500Z 26HP - 48” Mower Dec k 1/2008 15 TP 300-7368-IR-ZT-N P arking Brake Adjustment 1. Disengage the PTO, stop the engine, engage the parking brake, and remove the key from the ignition. 2. Raise the seat plate to gain access to the parking brake components. 3. Measure the distance from the top of the brake spring rod (C, Figure 23) to the top of ...

  • Briggs & Stratton 500Z - 26 - page 16

    500Z 26HP - 48” Mower Dec k TP 300-7368-IR-ZT-N 1/2008 16 PRODUCTS, INC. 535 Macon Street McDonough, GA., 30253 www.snapper.com The Snapper logo is a trademark of Briggs & Stratton Corporation, Milwaukee, WI, USA Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights ...

Fabricant Briggs & Stratton Catégorie Lawn Mower Accessory

Les documents que nous recevons du fabricant de l'appareilBriggs & Stratton 500Z - 26 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Briggs & Stratton
- manuels d’utilisations 500Z - 26
- fiches produit Briggs & Stratton
- dépliants
- ou étiquettes-énergie Briggs & Stratton 500Z - 26
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Briggs & Stratton 500Z - 26.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Briggs & Stratton 500Z - 26, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Briggs & Stratton 500Z - 26. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Briggs & Stratton 500Z - 26.

Manuel d’utilisation complet de l’appareil Briggs & Stratton 500Z - 26, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Briggs & Stratton 500Z - 26 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Briggs & Stratton 500Z - 26.

Le manuel d’utilisation complet Briggs & Stratton, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Briggs & Stratton 500Z - 26 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Briggs & Stratton 500Z - 26, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lBriggs & Stratton 500Z - 26 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Briggs & Stratton 500Z - 26 - qui devraient nous aider dans les premières étapes lors de l'utilisation Briggs & Stratton 500Z - 26
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Briggs & Stratton 500Z - 26
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Briggs & Stratton 500Z - 26 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Briggs & Stratton 500Z - 26?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Briggs & Stratton 500Z - 26, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Briggs & Stratton 500Z - 26 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)