Manuel d’utilisation Canon MiniTT1

40 pages 2.65 mb
Télécharger

Aller à la page of 40

Summary
  • Canon MiniTT1 - page 1

    Owner’ s Manual MiniTT1 ™ / FlexTT5 ™ for Canon 340 – 354 MHz, US FCC / Canada IC ...

  • Canon MiniTT1 - page 2

    Please pay attention to the following safety warnings: • Operating temperature: above -15° C (5° F) and below 50° C (120° F) • Storage temperature, without batteries: above -30° C (-22° F) and below 85° C (185° F) -- Remove batteries during storage. • Battery Requirements: Qty . 2 AA (IEC:LR6) for FlexTT5 CR2450 or CR2354 for MiniTT1 ...

  • Canon MiniTT1 - page 3

    Congratulations on your purchase of the PocketWizard MiniTT1 ™ / FlexTT5 ™ System for Canon DSLR E-TTL II cameras and flashes . Canon owners can use the MiniTT1 T ransmitter and FlexTT5 T ransceiver to control single or multiple off-camera Canon E-TTL II ashes at speeds up to 8fps. The PocketWizar d ControlTL™ System takes the complex E-T ...

  • Canon MiniTT1 - page 4

    T able of Contents 4 Safety Warnings 2 Congratulations 3 Batteries 6 MiniTT1 and FlexTT5 Key Features 7 MiniTT1 Feature Call-outs 8 FlexTT5 Feature Call-outs 9 READ ME FIRST 10 Powering On 11 Basic Wireless E-TTL II: MiniTT1 OO FlexTT5 12 No Flash on Camera 12 Flash on Camera 13 Ratio Wireless E-TTL II: MiniTT1 OO FlexTT5 14 Flash on Camera 14 Gene ...

  • Canon MiniTT1 - page 5

    T able of Contents (cont’d) 5 HyperSync ® & High Speed Sync (FP Flash) 18 Advanced Features via PocketWizar d Utility 20 Channels 22 Channel T ables 23 LEARN Mode 24 Remote Camera T riggering 26 Auto-Relay Mode 27 Reset 28 Status LED 29 Mounting 30 Long Range Performance 31 T roubleshooting 32 Canon Compatibility 35 Specifications 36 FCC Wa ...

  • Canon MiniTT1 - page 6

    FlexTT5 Battery Polarity MiniTT1 Battery Polarity CR2450 & CR2354 batteries Batteries CAUTION T ur n OFF your equipment (PocketWizard units, electronic flash units, cameras, etc .) before making connections or changing batteries. FlexTT5: Install 2 fresh AA (IEC:LR6) batteries into the FlexTT5 T ransceiver . Make sure to note proper polarity . ...

  • Canon MiniTT1 - page 7

    What’ s in the Box? - MiniTT1 or FlexTT5 - Batteries - USB Cord - QuickGuide MiniTT1 and FlexTT5 Key F eatures ControlTL: PocketWizard’ s newest rmware platform taps into the camera’ s digital communications to enable an entirely new level of remote ash capabilities through our proven radio system, beginning with remote TTL for Canon E- ...

  • Canon MiniTT1 - page 8

    Locking Ring (on bottom foot) page 12 Configuration/Channel 1 Configuration/Channel 2 Power Off page 11 , 22 Internal Antenna page 31 TEST/LEARN Button page 24 Battery Compartment (on bottom) page 6 USB Connector (under rubber cover) page 20 Status LED page 29 Canon-style Hot Shoe with Pass Through page 12 MiniTT1 ™ 8 ...

  • Canon MiniTT1 - page 9

    Adjustable Antenna page 31 USB Connector (behind antenna) page 20 Locking Ring (on bottom foot) page 30 Configuration/Channel 1 Configuration/Channel 2 Power Off page 11 , 22 TEST/LEARN Button page 24 Zone Selector page 14 Lanyard Loop page 30 1/4-20 mount (on bottom) page 30 Battery Compartment (2 AA [IEC:LR6]) page 6 Canon-style Hot Shoe with P ...

  • Canon MiniTT1 - page 10

    READ ME FIRST If this is the first time you are using a remote E-TTL II flash system, we recommend you consult your camera and flash manuals for your camera for the basics of positioning your flash units. Review the owner’s manuals for your camer a and flash system. For most basic functions when using Canon’ s system or PocketWizard’ s, opera ...

  • Canon MiniTT1 - page 11

    Power switch OFF Power switch ON and set to C.1 1. T urn OFF all your equipment ( PocketWizard radios, electronic flashes, cameras, etc.) before making connections. 2. When all equipment is connected, turn ON your MiniTT1 or FlexTT5 first by setting the power switch to C.1 or C.2 (see Channels for more information on C.1 and C.2). V erify radio bli ...

  • Canon MiniTT1 - page 12

    MiniTT1 on camera shoe Speedlite on FlexTT5 mounted on flash stand Basic Wireless E-TTL II: MiniTT1 OO FlexTT5 No Flash on Camera This simple mode of operation allows you to use one or more remote E-TTL II ashes as one zone of light. All remote E-TTL II ashes will re at the same power level which is chosen automatically by the camera. 1. ...

  • Canon MiniTT1 - page 13

    Speedlite on MiniTT1 in camera shoe in <MASTER> mode Flash on Camera This mode is identical to the previous page, adding a ash to the top hot shoe of the MiniTT1. All remote E-TTL II ashes and the master ash will be treated as one zone of light and will re at the same power level which is chosen automatically by the camera. IMPORT ...

  • Canon MiniTT1 - page 14

    Ratio Mode FlexTT5 Zone A FlexTT5 Zone B Ratio Wireless E-TTL II: MiniTT1 OO FlexTT5 Flash on Camera This mode uses Canon’ s Wireless Flash Ratio with E-TTL II system. Place remote ashes into different slave groups and control the balance of light among the groups or zones. O  Please read your Canon manuals for more information on Flash Rat ...

  • Canon MiniTT1 - page 15

    Canon ST -E2 Ratio Wireless E-TTL II: MiniTT1 OO FlexTT5 (cont’d) General E-TTL II Considerations There are several important factors to keep in mind when using the ControlTL system to extend Canon’ s wireless functionality: • Operate the camera normally by pressing the shutter release button halfway to establish focus or metering before shoo ...

  • Canon MiniTT1 - page 16

    Manual Flash There are many ways to use PocketWizard radios to trigger manual ashes. Any PocketWizard T ransmitter can be used for triggering remote manual ashes. You may have as many remote PocketWizard radios on the same channel as you would like. The FlexTT5 used as a receiver can trigger a compatible Canon Speedlite set to manual mode in ...

  • Canon MiniTT1 - page 17

    Use for remote manual flash FlexTT5 mounted with V elcro ® & connected to studio flash 17 Manual Flash (cont’d) Other Manual Flashes Connect the remote FlexTT5’ s port to your ash’ s sync terminal using: a) the correct PocketWizard ash sync cable for best results. - or - b) your ash’ s original sync cable and a PocketWizard ...

  • Canon MiniTT1 - page 18

    Setting the HyperSync Offset in the PocketWizard Utility HyperSync ® & High Speed Sync (FP Flash) HyperSync allows for a PocketWizard connected ash to begin ring just *before* the camera triggers a sync pulse. Since you are triggering “faster than a wire” with HyperSync, you can sync at shutter speeds faster than X-sync for many came ...

  • Canon MiniTT1 - page 19

    Front Curtain Clipping = move HyperSync slider towards 0 Rear Curtain Clipping = move HyperSync slider away from 0 19 HyperSync ® & High Speed Sync (FP Flash) (cont’d) HyperSync is set in a transmitting radio only . It is not used in a remote FlexTT5. All receiving PocketWizard radios, including the Plus II, etc., will trigger in sync with H ...

  • Canon MiniTT1 - page 20

    MiniTT1 USB port FlexTT5 USB port PocketWizard Utility Adv anced Features via P ocketWizard Utility Advanced features in the MiniTT1 and FlexTT5 are available when using the PocketWizard Utility and connecting your radio to your PC or Mac via a USB cable. Be sure to install the Utility before connecting! Download the latest version of the Utility a ...

  • Canon MiniTT1 - page 21

    21 Advanced F eatures via PocketWizard Utility (cont’d) Remote TTL Flash Sleep Delay: Normally your ControlTL transmitter tells all remote E-TTL II ashes to sleep when the camera sleeps. This saves batteries in the remote ash but could cause the ash to take a moment to be ready before the next trigger . Enable this feature to have your C ...

  • Canon MiniTT1 - page 22

    Channels Channels enable you to work with other photographers and to keep your triggering exclusive. Some channels operate on different frequencies to help you avoid interference. All PocketWizard radio slaves set to the same channel work together . ControlTL uses a new channel system in addition to the Standard channel system used in other PocketW ...

  • Canon MiniTT1 - page 23

    23 A MiniTT1 T ransmitter or a FlexTT5 T ransceiver always transmits on a Standard Channel and a ControlTL Channel for every trigger . Make sure you choose a set of channels/ frequencies that will not interfere with or trigger other PocketWizard users. When using ControlTL channels 5 through 14, you might interfere with a MultiMAX user on Standard ...

  • Canon MiniTT1 - page 24

    TEST/LEARN Button LEARN Mode Channels can be taught via the PocketWizard Utility . See the Utility’ s help for more information. T eaching via the Utility is recommended. Channels can also be taught in the eld using PocketWizard transmitters. Tr ansmitting channel: A MiniTT1 or FlexTT5 learning from a PocketWizard transmitter will learn both a ...

  • Canon MiniTT1 - page 25

    LEARN Mode (cont’d) For remote E-TTL II to function, the ControlTL channel must be learned. If you see only 1 or 2 green blinks after teaching then a Standard channel was learned and E-TTL II will not function. If you desire E-TTL II functionality , teach the FlexTT5 again from the MiniTT1 or FlexTT5 to be used as the primary transmitter and look ...

  • Canon MiniTT1 - page 26

    FlexTT5 connected to remote camera Hold up and away for best range Remote Camera T riggering As with other PocketWizard radios, the MiniTT1 and FlexTT5 can be used to trigger a remote camera. T o perform this operation a PocketWizard motor drive cable is required. For cameras with Canon’ s E3 connector , you need the PocketWizard CM-E3-ACC cable. ...

  • Canon MiniTT1 - page 27

    FlexTT5 configured for Auto-Relay with local Speedlite Auto-Relay Mode Y ou can trigger ashes in sync with your remote camera. This is called Relay Mode. Here’ s how it works: • Press TEST on a PocketWizard that you are holding in your hands. • The FlexTT5 connected to your remote camera receives the signal and triggers your camera. • T ...

  • Canon MiniTT1 - page 28

    Flex TEST button Reset The MiniTT1 and FlexTT5 can be reset in the eld. There are two types of reset. RESET A: Returns both C.1 and C.2 to the channels you last set in the PocketWizard Utility . Reset A is primarily used for resetting channels that were taught in the eld. 1. T urn the radio off 2. While holding TEST , slide the power switch t ...

  • Canon MiniTT1 - page 29

    MiniTT1 Status LED FlexTT5 Status LED Status LED The Status LED indicates that the unit is powered on, and displays battery level and other special status modes. Under normal operation the LED will display a short blink every 2 seconds. This is the normal “powered on and waiting for trigger” blink. The color of the LED indicates battery level: ...

  • Canon MiniTT1 - page 30

    Speedlite Stand Maximum range, OC-E3 cord with added ferrite clamp Maximum range, no cord 30 Velcro ® Mounting Mount a remote FlexTT5 T ransceiver using any of the following methods. ...

  • Canon MiniTT1 - page 31

    Positioning Blocking Signal Acceptabl eW orst Best Long Range P erformance Long distance performance from your PocketWizards depends on the orientation and position of the units. Whenever possible, try to maintain a line of sight between the units and keep the antennas parallel. While radio does not require line of sight, it does help dramatically ...

  • Canon MiniTT1 - page 32

    32 T roubleshooting Why is my photo not properly exposed? Consult the owner’ s manuals for your ash and camera to understand how exposure decisions are made. While the ControlTL system can greatly expand the operating range of Canon’ s E-TTL II system, and over - come inherent problems with an optical communication system, it does nothing wi ...

  • Canon MiniTT1 - page 33

    T roubleshooting (cont’d) Why is my exposure bouncing around? If you are in Shutter Priority mode (Tv) and the ambient light levels are changing dramatically shot to shot, it is possible for the camera and ash to mis-communicate. The camera ma y have shifted values before the radio had time to transmit them. T ry another mode or make sure to r ...

  • Canon MiniTT1 - page 34

    34 Notes ...

  • Canon MiniTT1 - page 35

    Canon Compatibility 35 The MiniTT1/FlexTT5 are E-TTL II compatible with these Canon cameras: DSLR Cameras 1Ds MKIII, MKII, 1D MKIII, MKII, 1D MKII N 5D, 5D MKII 1 20D, 30D 2 , 40D, 50D Rebel XT / 350D, Rebel XT i / 400D, Rebel XS / 1000D, Rebel XSi / 450D The MiniTT1/FlexTT5 are E-TTL II compatible with these Canon flashes: Flash Units 580EX, 580E ...

  • Canon MiniTT1 - page 36

    36 Specifications See Channel T ables for more information on Standard and ControlTL Frequencies and Channels MiniTT1 FlexTT5 E-TTL Compatibility Canon E-TTL II Canon E-TTL II Maximum Range MiniTT1 triggering remote PocketWizards FlexTT5 triggering remote PocketWizards on Standard channels: on Standard channels: 1200 feet (365 meters) 1200 feet (3 ...

  • Canon MiniTT1 - page 37

    Specifications (cont’d) MiniTT1 FlexTT5 Camera/P1 Port 1/8” (3.5 mm) stereo miniphone for 2-stage remote camera triggering. Port V oltage Handling: up to 50 Volts, 100 milliamp continuous Tip = T rigger Ring = Pre-T rigger Sleeve = Ground Flash/P2 Port 1/8” (3.5 mm) mono miniphone. Port V oltage Handling: up to 200 Volts, 4 amps peak, 250 mi ...

  • Canon MiniTT1 - page 38

    38 ...

  • Canon MiniTT1 - page 39

    WARNING Changes or modifications to this unit not expressly approved by the party r esponsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide r ...

  • Canon MiniTT1 - page 40

    For more information on this product, including detailed features and specications, go to: www .PocketWizard.com © 2009 LPA Design, Inc. All rights reserved. Product features and specications are subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT5, HyperSync, Plus II and MultiMAX are either trademarks or registered tr ...

Fabricant Canon Catégorie Camera Accessories

Les documents que nous recevons du fabricant de l'appareilCanon MiniTT1 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Canon
- manuels d’utilisations MiniTT1
- fiches produit Canon
- dépliants
- ou étiquettes-énergie Canon MiniTT1
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Canon MiniTT1.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Canon MiniTT1, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Canon MiniTT1. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Canon MiniTT1.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Canon MiniTT1, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Canon MiniTT1 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Canon MiniTT1.

Le manuel d’utilisation complet Canon, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Canon MiniTT1 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Canon MiniTT1, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCanon MiniTT1 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Canon MiniTT1 - qui devraient nous aider dans les premières étapes lors de l'utilisation Canon MiniTT1
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Canon MiniTT1
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Canon MiniTT1 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Canon MiniTT1?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Canon MiniTT1, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Canon MiniTT1 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)