Manuel d’utilisation Clarion APX200.2

16 pages 0.27 mb
Télécharger

Aller à la page of 16

Summary
  • Clarion APX200.2 - page 1

    ...

  • Clarion APX200.2 - page 2

    INTRODUCTION The Clarion APX200.2 and APX400.2 are full-featured two-channel amplifiers. incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, including those with sate ...

  • Clarion APX200.2 - page 3

    DESCRIPTION The Clarion APX200.2 and APX400.2 two-channel amplifiers provide 2x70 watts and 2x110 watts of power into a 4 ohm load and 2x110 watts and 2x190 watts of power into a 2 ohm load. These full featured models are an excellent choice for a variety of car audio sound system configurations. The APX200.2 and APX400.2 use an unregulated MOSFET ...

  • Clarion APX200.2 - page 4

    • Gain Control - This allows you to set the nominal operating level of the amplifier . The amplifier ’ s range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high-Q” (i.e. narrow frequency ban ...

  • Clarion APX200.2 - page 5

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2 and APX400.2 both contain power and speaker connections as shown below. 5 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery + 12v Input 6. 25 Amp Fuse / 40 Amp Fuse Figure 2- ...

  • Clarion APX200.2 - page 6

    APPLICA TIONS The Clarion APX200.2 and APX400.2 2-channel car audio amplifiers can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Set X-Over Mode to LP and adjust ...

  • Clarion APX200.2 - page 7

    2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or sa ...

  • Clarion APX200.2 - page 8

    Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 318 265 199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a ...

  • Clarion APX200.2 - page 9

    INSTALLA TION This section lists Mounting and W iring Precautions for installing a Clarion APX200.2 or APX400.2. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your ...

  • Clarion APX200.2 - page 10

    4. A secure clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible snd securely connect to the car chassis to minimize resistance and avoid noise problems. 5. Add an external fuse on the amplifier ’ s positive (+) power lead and connect it as close as possible to the vehicle’s (+) ...

  • Clarion APX200.2 - page 11

    11 Figure 6. - Electrical connections for the APX200.2 or the APX400.2 ...

  • Clarion APX200.2 - page 12

    SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. T urn the Gain Control all the way counter-clockwise. 2. T urn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all T one or Equalizati ...

  • Clarion APX200.2 - page 13

    FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay , slowly increase the V olume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to T roubleshooting. Depending on your system design, the levels may become quite loud even a ...

  • Clarion APX200.2 - page 14

    14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to e ...

  • Clarion APX200.2 - page 15

    NOTES 15 ...

  • Clarion APX200.2 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX2CH-10 Rev .1 (02/00) ...

Fabricant Clarion Catégorie Power Supply

Les documents que nous recevons du fabricant de l'appareilClarion APX200.2 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Clarion
- manuels d’utilisations APX200.2
- fiches produit Clarion
- dépliants
- ou étiquettes-énergie Clarion APX200.2
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Clarion APX200.2.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Clarion APX200.2, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Clarion APX200.2. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Clarion APX200.2.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Clarion APX200.2, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Clarion APX200.2 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Clarion APX200.2.

Le manuel d’utilisation complet Clarion, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Clarion APX200.2 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Clarion APX200.2, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lClarion APX200.2 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Clarion APX200.2 - qui devraient nous aider dans les premières étapes lors de l'utilisation Clarion APX200.2
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Clarion APX200.2
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Clarion APX200.2 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Clarion APX200.2?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Clarion APX200.2, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Clarion APX200.2 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)