Manuale per l’uso APC 10-40KW 400V UPS

90 pagine 8.07 mb
Scarica

Vai alla pagina of 90

Summary
  • APC 10-40KW 400V UPS - page 1

    APC Silcon 10-40kW 400V UPS Installation Guide Copyright 2000 APC Denmark ApS This manual is subject to change without notice and does not represent a commitment on the part of the vendor ...

  • APC 10-40KW 400V UPS - page 2

    2 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Thank You! Thank you for chosing the APC Silcon Series UPS. Please read this Installation Guide thoroughly prior to installing the system. It provides important information on safe and efficient installation. The installation and use of this product must comply with national, federal, state, ...

  • APC 10-40KW 400V UPS - page 3

    990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 3 Contents 1.0 Introduction 5 1.1 Tools and Equipment 5 2.0 Unpacking 6 3.0 Installation 8 3.1 Requirements on Site 8 3.1.1 Cabinet Dimensions H*xWxD - 1400xWx800 [mm]. Width as in below table: 8 3.2 Footprint 10 3.2.1 600mm UPS Cabinet with 1xBP I or Isolation Transformer 10 3.2.2 800mm UPS C ...

  • APC 10-40KW 400V UPS - page 4

    4 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 6.1.3 Operating The External Service Bypass Switch 57 6.2 Service Bypass Panel for Parallel Redundant Operation 59 6.2.1 Two Parallel Systems with Service Bypass Panel 60 6.2.2 Parallel/Redundant Operation with Service Bypass Panel and External Battery via MCCB 61 6.2.3 Operating External Se ...

  • APC 10-40KW 400V UPS - page 5

    Introduction 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 5 1.0 Introduction Power regulation varies from country to country, and information given in this installation guide can therefore only be of a general nature. Electricians should therefore always refer to national and local electrical codes prior to installing the UPS system. 1.1 ...

  • APC 10-40KW 400V UPS - page 6

    6 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Unpacking 2.0 Unpacking 1. To unpack UPS unit, remove top and bottom screws from side plates of packaging and lift up side plates 2. Verify compliance between type label on reverse side of front door and system ordered. Check input and output voltage 3. Copy type label data to label copy bel ...

  • APC 10-40KW 400V UPS - page 7

    Unpacking 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 7 Copy of type label PLEASE RECYCLE The shipping materials for the APC Silcon UPS are recyclable. Please save them for later use or dispose of them appropriately. ...

  • APC 10-40KW 400V UPS - page 8

    8 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Installation 3.0 Installation 3.1 Requirements on Site All system parts are accessible from front or top of UPS. Cable entries are accessible from bottom. A 1m free space on all sides should be allowed during installation. Once the system is installed it may be placed close to walls as long ...

  • APC 10-40KW 400V UPS - page 9

    Installation 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 9 Cabinets 600 mm wide 10-20kW with 1xBP l 1400 mm 10-20kW with 2xBP l 800 mm wide 1400 mm 1000 mm wide 10-20kW with 3xBP l 40kW without batteries 600 mm wide 1000 mm wide 1400 mm 40kW with 2xBP l 1400 mm 1400 mm 1400 mm APC Isolation Transformer module 10-80kW 600 mm wide Battery ...

  • APC 10-40KW 400V UPS - page 10

    10 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Installation 3.2 Footprint 3.2.1 600mm UPS Cabinet with 1xBP I or Isolation Transformer 3.2.2 800mm UPS Cabinet with 1xBP I or Built-in Isolation Transformer, or 2xBP I Rear Front Power cable entry Com. cable entry Rear Front Power cable entry Com. cable entry ...

  • APC 10-40KW 400V UPS - page 11

    Installation 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 11 3.2.3 1000mm Cabinet for 10-20kW UPS with 3xBP I 3.2.4 600mm Cabinet for 40kW UPS without Batteries Rear Front Power cable entry Com. cable entry Rear Front Power cable entry Com. cable entry ...

  • APC 10-40KW 400V UPS - page 12

    12 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Installation 3.2.5 1000mm Cabinet for 40kW UPS with 2xBP I 0 195 Rear Front Power cable entry Com. cable entry ...

  • APC 10-40KW 400V UPS - page 13

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 13 4.0 External Connection 4.1 Connecting the UPS 4.1.1 Connecting the 10-20kW UPS CAUTION! At a switch mode load of 100% the neutral must be rated for 200% output phase current CAUTION! This UPS unit is an EN 50091-2 product and may cause radio interference in a domestic e ...

  • APC 10-40KW 400V UPS - page 14

    14 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection * DIN gL types PVC cables isolated to withstand ambient temperature of max. 30oC ** Must be rated as external PE cable if mains system is not supplying PE NOTICE! Check correct phase rotation of mains input voltage!! Max. input/output cables: 35mm 2 . If there is no neut ...

  • APC 10-40KW 400V UPS - page 15

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 15 4.1.2 Connecting the 40kW UPS NOTICE! Install gland plate in bottom of unit CAUTION! At a switch mode load of 100% the neutral must be rated for 200% output phase current. CAUTION! This UPS unit is an EN 50091-2 product and may cause radio interference in a domestic envi ...

  • APC 10-40KW 400V UPS - page 16

    16 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection * DIN gL types PVC cables isolated to withstand ambient temperature of max. 30oC. ** Must be rated as external PE cable if mains system is not supplying PE. NOTICE! Check correct phase rotation of mains input voltage!! Max. input/output cables: 120mm 2 . Battery: 70 mm 2 ...

  • APC 10-40KW 400V UPS - page 17

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 17 4.2 System Integration Interface System Integration Interface (SII) is the control link between UPS and system main switches as shown in above diagram. The purpose of the SII is to ensure correct operation of switches without losing system output power. Auxiliary contact ...

  • APC 10-40KW 400V UPS - page 18

    18 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.2.1 Connections Blue Brown ...

  • APC 10-40KW 400V UPS - page 19

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 19 Terminal Blocks: X003/X004 (Anxiliary Contacts) When switching Q001, Q002, Q010, Battery Breaker 1 or Battery Breaker 2 from “ON or 1” to “OFF or 0”, the anxiliary contact has to be open BEFORE the corresponding main contacts are opened. When switching Q001, Q002 ...

  • APC 10-40KW 400V UPS - page 20

    20 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection The built-in parallel board connects two or more UPS systems in parallel, either to obtain increased system reliability or to obtain higher output power. The parallel board also ensures correct load-sharing between paralled systems. To prepare the UPS for parallel/redund ...

  • APC 10-40KW 400V UPS - page 21

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 21 External Control Cables External multicore cable is equipped with 15-pin SUB-D plug at either end. Connect pin 1 to pin 1, and pin 2 to pin 2 etc. up to pin 15 - with the exception of pin 8, which is not to be connected. Shield is connected to plug cover at both ends. Te ...

  • APC 10-40KW 400V UPS - page 22

    22 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.4 Communication Interface Board The 3-port ComInterface is used to establish an interaction between UPS and e.g. a computer system. Main purpose: To ensure a controlled computer shut-down in case of a mains supply failure. 4.4.1 Connections . . ...

  • APC 10-40KW 400V UPS - page 23

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 23 4.5 Connecting of APC Silcon Tripel Chassis The enclosed Triple Chassis must be connected to the serial port on the Communication Interface Board, and to the 24V supply (cables included). Terminal locations shown below. 23.62 inch/600mm Cabinet APC Silcon Triple Chassis ...

  • APC 10-40KW 400V UPS - page 24

    24 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.6 APC Silcon Triple Chassis The APC Silcon Triple Chassis (AP9604S) is an American Power Conversion (APC) external management peripheral that allows you to use monitoring and control management peripherals with your APC Silcon series UPS. The retrofit model (AP9604SR) ...

  • APC 10-40KW 400V UPS - page 25

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 25 4.6.2.3LEDs The APC Silcon Triple Chassis status LED provides important information concerning operation of the chassis. Refer to the table below for a description of the conditions indicated by the LED. 4.6.2.4Optional Power Input With the Optional Power input, you can ...

  • APC 10-40KW 400V UPS - page 26

    26 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.6.3.1Order of Management Peripheral Cards Because UPS signals are passed between management peripherals, you must install management peripheral cards in the correct order for them to work together properly. The card slots are numbered 1 to 3, from left to right, as vie ...

  • APC 10-40KW 400V UPS - page 27

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 27 To add card slots, you can daisy-chain the APC Silcon Triple Chassis with the standard Triple Chassis (AP9604) management peripheral, installing the APC Silcon Triple Chassis closer to the UPS. 4.6.4 Powering the APC Silcon Triple Chassis The APC Silcon Triple Chassis su ...

  • APC 10-40KW 400V UPS - page 28

    28 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.6.5 Troubleshooting The following table shows the solution to common problems with the operation of the Triple Chassis 4.6.5.1If Problems Persist For problems not covered in the troubleshooting chart or for persistent problems, follow this procedure: 1) Note the serial ...

  • APC 10-40KW 400V UPS - page 29

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 29 4) Pack the APC Silcon Triple Chassis carefully in its original packaging, if possible. Do not use polystyrene beads for packing. Damage sustained in transit is not covered under the warranty. Enclose a letter in the package with your name, address, RMA number, a copy of ...

  • APC 10-40KW 400V UPS - page 30

    30 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection UPS Shut Down RS-232 Input or Advanced Mode RS-232 Data RX In Line Fail RS-232 Output or Advanced Mode RS-232 Data TX Out Unregulated +24 VDC Output Normally Open Line Fail Signal Normally Open Low Battery Signal Normally Closed Line Fail Signal Common Chassis ...

  • APC 10-40KW 400V UPS - page 31

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 31 4.6.6.2Power, Physical, and Environmental Specifications. Item Specification Power Turn on voltage: > 22 VDC Turn off voltage: < 16 VDC Current draw (normal operation): 90 mADC Current draw (voltage < 16 VDC ): < 1 mADC Physical Size (H xW x D): 1.75 x 17.0 x ...

  • APC 10-40KW 400V UPS - page 32

    32 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.7 APC Silcon Battery Cabinets Installation and use of this product must comply with all national, federal, state, municipal or local codes. If you need assistance, please have your UPS model and serial number ready and call APC, see “How to Contact APC” in this gui ...

  • APC 10-40KW 400V UPS - page 33

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 33 4.7.1 Cabinets UPS with Built-in Batteries 4.7.2 Preparing Batteries CAUTION! Battery drawer weighs approx. 22 kg with batteries. The 12V, 7.2 Ah batteries are glued to drawer plate. Battery drawers present a risk of electric shocks. Prior to installation of battery draw ...

  • APC 10-40KW 400V UPS - page 34

    34 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection Battery drawers are wrapped in cardboard and delivered on pallets. Unpack battery drawers, checking that type, number and size comply with the order. Connect wire as shown below: ...

  • APC 10-40KW 400V UPS - page 35

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 35 800mm Battery Cabinet 1000mm Battery Cabine 4.7.3 Mounting Batteries Unscrew front frame of UPS and slide frame down as shown above. Battery drawers may be installed after removal of front cover. WARNING! Open front door of UPS and unscrew front cover. Do not install bat ...

  • APC 10-40KW 400V UPS - page 36

    36 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection Check all battery connections to ensure that proper contact is established. Insert battery drawers in the APC Silcon UPS Connect all battery drawers to the terminal on the left side of the column ...

  • APC 10-40KW 400V UPS - page 37

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 37 4.7.4 Final Checks CAUTION! Follow the “ start-up procedure ” in APC Silcon User Guide. IMPORTANT SAFETY INSTRUCTIONS a) The servicing of batteries requires battery knowledge and should be carried out or supervised by qualified personnel only. Keep unauthorized perso ...

  • APC 10-40KW 400V UPS - page 38

    38 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.7.5 APC Silcon Battery Cabinets Installation and use of this product must comply with all national, federal, state, municipal or local codes. If you need assistance, please have your UPS model and serial number ready and call APC, see the section “How to contact APC? ...

  • APC 10-40KW 400V UPS - page 39

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 39 4.7.5.1Installation of Batteries See Installation Guide for Battery Cabinet for: • Preparing Batteries and UPS • Dimensions and Weight • Connecting Batteries WARNING! The entire system contains HAZARDOUS AC/DC VOLTAGES from several power sources. Some terminals and ...

  • APC 10-40KW 400V UPS - page 40

    40 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.8 Battery Breaker Box/Fuse-box Battery Breaker Box/Fuse-box provides overcurrent and short-circuit protection for UPS installations with external batteries. CAUTION! Batteries connected to a UPS out of service for a period exceeding 8 days may be damaged. Refer to Sect ...

  • APC 10-40KW 400V UPS - page 41

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 41 4.8.1 Battery Breaker Box UPS Ampere Rating [A] Connection Cable [mm2] Max. short- circuit current [kA] Dimensions HxWxD [mm] Weight [kg] 10 kW 20 kW 40 kW 25 50 63 4 10 16 10 10 10 540x540x183 504x540x183 540x540x183 20 20 20 ...

  • APC 10-40KW 400V UPS - page 42

    42 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.8.2 Battery Breaker Box Connection Diagram X009 LED signal from UPS “OK to operate corresponding MCCB” X010 MCCB position signals for UPS X011 Trip for emergency stop (220-240V AC) Battery 1 Battery 2 Battery 1 Battery 2 UPS UPS Main cables are connected directly t ...

  • APC 10-40KW 400V UPS - page 43

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 43 4.8.3 Fuse-box UPS Ampere Rating [A] Connection Cable [mm 2 ] Max. short-circuit current [kA] Dimensions HxWxD [mm] Weight [kg] 10 kW 20 kW 40 kW 25 50 63 4 10 16 10 10 10 540x540x183 504x540x183 540x540x183 20 20 20 ...

  • APC 10-40KW 400V UPS - page 44

    44 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 External Connection 4.8.4 Fuse-box Connection Diagram X009 LED signal from UPS “ OK to operate corresponding fuse. ” X010 Released fuse signal for UPS Battery 1 Battery 2 Battery 1 Battery 2 UPS UPS ...

  • APC 10-40KW 400V UPS - page 45

    External Connection 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 45 4.8.5 UPS with External Battery in Battery Breaker Box/Fuse-box Configuration ...

  • APC 10-40KW 400V UPS - page 46

    46 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Programming Parameters 5.0 Programming Parameters Below table shows operating parameters programmable from keyboard. Only qualified users should re-set programming parameters. 5.1 Parameters * Factory settings in bold ** Only for systems with Battery Monitor active *** Do not leave system r ...

  • APC 10-40KW 400V UPS - page 47

    Programming Parameters 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 47 5.1.1 Programming Keys NOTICE! Display accuracy is + 1%, + digit. Scrolls up through list Scrolls down through list Stores parameters/ enter parameter stack Silences the audible alarm Chooses parameters Displays time Exits a mode Accesses alarm stack ...

  • APC 10-40KW 400V UPS - page 48

    48 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Programming Parameters 5.1.2 Programming Example - Switch to Bypass Operation Return to normal operation Follow same procedure to program other parameters. 5.2 System Configuration System configuration parameters are vital for correct system operation and are password- protected. NOTICE! Do ...

  • APC 10-40KW 400V UPS - page 49

    Programming Parameters 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 49 System Configuration Parameters (password protected) * Bold text refers to factory standard setting **Advanced Battery Monitor Parameter Setting* Comments Isolation Transformer Input YES, NO YES if optional input isolation transformer is available IsolationTransformer ...

  • APC 10-40KW 400V UPS - page 50

    50 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Programming Parameters 5.2.1 Programming Example - Change Charge Voltage to 446 NOTICE! Change charge voltages, battery warning limit, shut down voltage and high battery temperature limit by entering the actual value. See example above. ...

  • APC 10-40KW 400V UPS - page 51

    Programming Parameters 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 51 5.2.2 Programming Example - Change to Output Isolation Transformer available NOTICE! Change parameters by pressing the key once or several times. See example above. ...

  • APC 10-40KW 400V UPS - page 52

    52 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Programming Parameters 5.3 Programming Parameters for Advanced Parallel Operation To use the advanced parallel functions, the following parameters must be programmed: 1. “Station number” 2. “Highest station address” 3. “Advanced power management” 4. “APM test mode active” 5. ...

  • APC 10-40KW 400V UPS - page 53

    Programming Parameters 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 53 5.3.2 Programming example Example with four systems in parallel with separate batteries. • Programme the station addresses 1-4: 1 for UPS 1, 2 for UPS 2, 3 for UPS 3, and 4 for UPS 4. • All UPS systems have to be programmed to “Highest station address”:4. • ...

  • APC 10-40KW 400V UPS - page 54

    54 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.0 Options/Accessories Please contact your local APC representative for information on options/accessories available in your region. See “How to Contact APC” in this guide. 6.1 Service Bypass Panel for Single Operation UPS Exter- nal System Input Fuse [A] Max. Pro- ...

  • APC 10-40KW 400V UPS - page 55

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 55 *** If no external System Output fuses are available or if it has a higher value than indicated above, System Output and UPS Output cables should be dimensioned as System Input and UPS Input cables. ** Sizes according to IEC 364-5-532 for PVC insulated copper cables (max ...

  • APC 10-40KW 400V UPS - page 56

    56 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.1.1 Wiring up UPS with SBP in TN-C-S Network 6.1.2 Wiring up UPS with SBP in TN-S Network ...

  • APC 10-40KW 400V UPS - page 57

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 57 6.1.3 Operating The External Service Bypass Switch Action 1. Press on the k e yboard 2. Press or on the k e yboard until 3. Press on the k e yboard 4. Press on the k e yboard 5. Chec k lamp indication on the Service Bypass Panel 6. T urn the external bypass switch (Q003) ...

  • APC 10-40KW 400V UPS - page 58

    58 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.1.3.1Switching from External Bypass to Normal UPS Operation Action 1. T urn the input switch (Q002) to position ” 0 “ 2. Open the UPS front door and press the green "ON ” key 3. Press on the keyboard 4. Press or on the keyboard until 5. Press on the keyboard ...

  • APC 10-40KW 400V UPS - page 59

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 59 6.2 Service Bypass Panel for Parallel Redundant Operation Service Bypass Panel (SBP) Mains Supply System Output Control cables Q003 Q004 Q001b Q001a Q002b Q002a APC Silcon 400V UPS X020 X021 X020 X021 APC Silcon 400V UPS Battery Battery Breaker/ Fuse Box ...

  • APC 10-40KW 400V UPS - page 60

    60 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.2.1 Two Parallel Systems with Service Bypass Panel ...

  • APC 10-40KW 400V UPS - page 61

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 61 6.2.2 Parallel/Redundant Operation with Service Bypass Panel and External Battery via MCCB ...

  • APC 10-40KW 400V UPS - page 62

    62 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.2.3 Operating External Service Bypass Switch for Parallel Systems 6.2.3.1Bypassing Parallel UPS Systems CAUTION! Batteries connected to a UPS out of service for a period exceeding 8 days may be damaged. H002a ...

  • APC 10-40KW 400V UPS - page 63

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 63 Step 1-4 can be carried out with any of the parallel systems, ho we ver this will s witch all systems into bypass operation. 1. Press on the keyboard 2. Press or on the keyboard until 3. Press on the keyboard 4. Press on the keyboard All systems will transf er to bypass ...

  • APC 10-40KW 400V UPS - page 64

    64 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.2.3.2 Switching Parallel System from External Bypass into Normal UPS Operation H002a ...

  • APC 10-40KW 400V UPS - page 65

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 65 Action 1. Check that output s witch (Q004) is in position “ 0 ” 2. Check that all output s witches (Q002) are in position “ 0 ” 3. T ur n input s witches (Q001) to position “ 1 ” 4. Open the UPS front door and press the green “ ON ” push-botton 5. Press o ...

  • APC 10-40KW 400V UPS - page 66

    66 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.2.4 Isolating One UPS for Service/Maintenance In a redundant system, one UPS may be isolated for service/maintenance without affecting other UPSs. 1. Check that remaining UPS(s) is capable of carrying the load in the event that one UPS is isolated 2. Switch off system ...

  • APC 10-40KW 400V UPS - page 67

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 67 6.2.5 Switching Back to Normal Parallel/Redundant Operation 1. Turn input switch (Q001) and output switch (Q002) to position “ 1 ” 2. Charge capacitor, connect battery and start up UPS UPS will automatically switch to normal operation and start load-sharing with othe ...

  • APC 10-40KW 400V UPS - page 68

    68 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.3 Intersystem Synchronization Unit Intersystem Synchronization Unit System (ISU System) The ISU system consists of inter-connected ISUs. One ISU system may consist of up to 5 ISUs, regardles of ISU configuration. The ISU system synchronizes the voltage of parallel oper ...

  • APC 10-40KW 400V UPS - page 69

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 69 6.4 Relay Board Relays All relays are “fail safe”: In alarm modes, relay coil will be de-energized. Maximum load: 8.0A – 250VAC Minimum load: 0.05A – 6VAC 1 2 3 0.3A – 60VDC 0.05A – 6VDC ...

  • APC 10-40KW 400V UPS - page 70

    70 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.4.1 Relay Board/Relay Functions NOTICE! If alarm mode “ Communication to controller lost ” is active, ALL relays will indicate failure. Relay Number Message Alarm-trigging Events 1 ## (X002) Mains outside limits Mains voltage RMS outside limits Mains wave form (fas ...

  • APC 10-40KW 400V UPS - page 71

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 71 ## Delay programmable in configuration stack: “ Common fault delay ” . Settings 0,10,20,30 seconds. See section 5.2 in this guide for System configuration NOTICE! Alarm Trigging Events 1-2- 3-9-10-11-13 activates the corresponding alarm relay after the delay. Alarm T ...

  • APC 10-40KW 400V UPS - page 72

    72 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.5 Weight Equalizer Footprint - 600mm and 8 30 30 30 30 75 277.5 755 277.5 75 R6 19 Rear Front 490 - 600mm cabinet 690 - 800mm cabinet 550 - 600mm cabinet 750 - 600mm cabinet ...

  • APC 10-40KW 400V UPS - page 73

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 73 Footprint - 1000mm Cabinet 465 - 1000 mm cabinet 395 - 1000 mm cabinet 30 30 950 - 1000 mm cabinet 30 75 75 R6 277.5 277.5 755 Rear Front ...

  • APC 10-40KW 400V UPS - page 74

    74 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.6 Remote Display With the remote display unit data may be displayed at distances of up to 25 m from UPS. For extended communication distance, see section below. Remote display may easily be connected to UPS via one of the two serial communication ports on the communica ...

  • APC 10-40KW 400V UPS - page 75

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 75 6.6.1.1Connections Without Converter Connect a 25-pin female Sub-D and a 9-pin male Sub-D connector with a 3-wire shielded cable, as shown in the table below. Connect shield at one end only. Pin Connection for Interconnection Cable (without converter): 6.6.1.2Connections ...

  • APC 10-40KW 400V UPS - page 76

    76 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.6.2 Remote Display Installation 6.6.2.1Connecting RS232C and Mains Adapter 6.6.2.2Remote Display Power Supply The remote display is supplied by normal AC power with no battery back-up. For UPS data transmission to remote display to remain unaffected during power failur ...

  • APC 10-40KW 400V UPS - page 77

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 77 6.6.3 Remote Display Use The remote display is an inactive unit unable to influence the operation of the UPS: Some of the alarms visible on the internal display are also available on the remote display (See the Alarm section in the APC Silcon User Guide). 6.6.3.1Initiati ...

  • APC 10-40KW 400V UPS - page 78

    78 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.7 Isolation Transformer UPS Height [mm] Width [mm] Depth [mm] Weight [kg] 10 kW 20 kW 40 kW 1400 1400 1400 600 600 600 800 800 800 185 245 405 NOTICE! APC isolation transformers are available in various configuration. Contact your local APC representative for further i ...

  • APC 10-40KW 400V UPS - page 79

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 79 6.7.1 Connecting Isolation Transformer *DIN gL types PVC cables isolated to withstand a maximum ambient temperature of 30 o C. NOTICE! If an MCCB is used in stead of external input fuses, the MCCB load capacity must be 8xIn (nominal current) for minimum 10 ms. Isolation ...

  • APC 10-40KW 400V UPS - page 80

    80 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories NOTICE! Check correct phase rotation of mains input voltage! Maximum input/output cables: 35mm 2 . If in- put neutral is not available, an optional Dzn0 or Dyn11 input isolation transformer must be used. NOTICE! All external cable dimensions are recommended sizes only. R ...

  • APC 10-40KW 400V UPS - page 81

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 81 6.7.2 Wiring up UPS with External Yyn0 Isolation Transformer at Output WARNING! Isolation transformer provides galvanic isolation between mains supply and load. Load will loose galvanic isolation if isolation transformer is bypassed NOTICE! Refer to local legal regulatio ...

  • APC 10-40KW 400V UPS - page 82

    82 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.7.3 Wiring up UPS with External Yyn0 Isolation Transformer at Input WARNING! Isolation transformer provides galvanic isolation between mains supply and load. Load will loose galvanic isolation if isolation transformer is bypassed. NOTICE! Refer to local legal regulatio ...

  • APC 10-40KW 400V UPS - page 83

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 83 6.7.4 Wiring up UPS with External Optional Dzn0 Isolation Transformer at Input WARNING! Isolation transformer provides galvanic isolation between mains supply and load. Load will loose galvanic isolation if isolation transformer is bypassed. NOTICE! Refer to local legal ...

  • APC 10-40KW 400V UPS - page 84

    84 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Options/Accessories 6.7.5 Wiring up UPS with External Optional Dzn0 Isolation Transformer at Output WARNING! Isolation transformer provides galvanic isolation between mains supply and load. Do not bypass isolation transformer in order to avoid damaging circulation currents and to prevent lo ...

  • APC 10-40KW 400V UPS - page 85

    Options/Accessories 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 85 6.7.6 Wiring up UPS with External Optional Dyn11 Isolation Transformer at Input WARNING! Isolation transformer provides galvanic isolation between mains supply and load. Do not bypass isolation transformer in order to avoid damaging circulation currents and to prevent lo ...

  • APC 10-40KW 400V UPS - page 86

    86 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 System Specifications 7.0 System Specifications 7.1 Technical Data 7.2 Back-up Time / Dimensions / Weigh Voltage 3x380/400/415V Input Voltage tolerance Normal operation Bypass operation +15% +10% (standard) +4, 6, 8% (programmable) Frequency 50Hz/60Hz +6 standard +0.5-8% (programmable) Inpu ...

  • APC 10-40KW 400V UPS - page 87

    Warranty 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 87 8.0 Warranty 8.1 APC Silcon Series Limited Factory Warranty APC warrants that the unit, when properly installed and commissioned by APC or APC authorized service personnel, shall be free from defects in materials and workmanship for a period of (1) year from the date of installatio ...

  • APC 10-40KW 400V UPS - page 88

    88 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 Appendix 9.0 Appendix 9.1 Table 1. Installation Planning Data Main Input Breaker Field Wiring* Battery Bank** UPS Module Service Bypass Panel Field Wiring Output Breaker * ** Internal Batteries available for 40kW units and smaller * * Q1 Q2 Q3 * Not supplied by APC Installation Planning Dat ...

  • APC 10-40KW 400V UPS - page 89

    Appendix 990-4050 Installation Guide APC Silcon 10-40kW 400V UPS 89 Notes: 1. Nominal input current based on rated load. 2. Maximum input current based on rated load + full battery recharge. Full battery recharge assumed to increase input current with 10%. 3. Nominal power consumption (column 1c) based on nominal input current (1e) and the correspo ...

  • APC 10-40KW 400V UPS - page 90

    90 Installation Guide APC Silcon 10-40kW 400V UPS 990-4050 How to Contact APC 10.0 How to Contact APC APC Corporate 132 Fairgrounds Road West Kingston, RI 02892 USA Telephone: 401 789-5735 Fax: 401 789-3710 PowerFax™: 800 347-FAXX Pre-sales Technical Support 877-474-5266 (1-877-4Silcon) Post-sales Technical Support 877-287-7835 (1-877-2UPS-TEK) W ...

Fabbricante APC Categoria Power Supply

I documenti che otteniamo dal fabbricante del dispositivoAPC 10-40KW 400V UPS possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici APC
- manuali per l’uso 10-40KW 400V UPS
- schede prodotto APC
- opuscoli
- o etichette energetiche APC 10-40KW 400V UPS
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso APC 10-40KW 400V UPS.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione APC 10-40KW 400V UPS, manuali di manutenzione, brevi manuali o manuali utente APC 10-40KW 400V UPS. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto APC 10-40KW 400V UPS.

Manuali per l’uso simili

Manuale completo del dispositivo APC 10-40KW 400V UPS, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare APC 10-40KW 400V UPS dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti APC 10-40KW 400V UPS.

Il manuale per l’uso completo APC, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale APC 10-40KW 400V UPS - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice APC 10-40KW 400V UPS, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per APC 10-40KW 400V UPS che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo APC 10-40KW 400V UPS - che ci dovrebbe aiutare nei primi passi durante l'uso APC 10-40KW 400V UPS
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del APC 10-40KW 400V UPS
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio APC 10-40KW 400V UPS in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su APC 10-40KW 400V UPS?

Utilizza il modulo sottostante

Se non hai risolto il problema con APC 10-40KW 400V UPS con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con APC 10-40KW 400V UPS è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)