Italiano dropdown-ico

Manuale per l’uso American Standard 70145A 11/00

19 pagine 0.34 mb
Scarica

Vai alla pagina of 19

Summary
  • American Standard 70145A 11/00 - page 1

    Form No. 70145A 11/00 AMERICAN SANDERS TECHNOLOGY Printed in the READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the ma ...

  • American Standard 70145A 11/00 - page 2

    Page 2 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Contents of this Book Operator Safety Instructions ........................................................ 3 Machine Safety Statements ......................................................... 5 Introduction and Machine Specifications ..................................... 6 230V E ...

  • American Standard 70145A 11/00 - page 3

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 3 DANGER means: Severe bodily injury or death can occur to you or other personnel if the DAN- GER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your ma ...

  • American Standard 70145A 11/00 - page 4

    Page 4 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual DANGER : This machine had rotating and moving elements that can cause serious injury. Follow these precautions: • Do not operate this machine unless all guards, doors and covers are secure and in place. • Keep hands, feet and loose clothing away from all moving parts. • Do no ...

  • American Standard 70145A 11/00 - page 5

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 5 The following safety decals are mounted on the machine as shown. If these or any other machine decal, label or plate should become damaged or illegible, install a new decal in its place. Contact your local autho- rized distributor for new decals. The following information signals p ...

  • American Standard 70145A 11/00 - page 6

    Page 6 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Introduction and Machine Specifications Operating Control Lever Motor Starter / Protector Tension Release Lever Level Adjustment Nut Sanding Pressure Adjustment PART NUMBER 07094C ABRASIVE SIZE 29 1 / 2 " x 7 7 / 8 " CONTACT WHEEL SPEED 2850 rpm (revolutions per minute) A ...

  • American Standard 70145A 11/00 - page 7

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 7 230V Electrical Connection Instructions CAUTION: This machine will operate only on AC frequency and on electrical voltage shown on the motor nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has a plug as show ...

  • American Standard 70145A 11/00 - page 8

    Page 8 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Ho w to T ranspor t the Machine WARNING : The machine is heavy. Remove the motor from the machine before transporting. Get help loading the machine and motor. Transporting the Machine - One Person To transport the machine, follow this procedure: 1. Make sure the power cable is disc ...

  • American Standard 70145A 11/00 - page 9

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 9 NOTE: It is not necessary to adjust the fan belt independently during this procedure or during replace- ment. The idler pulley is factory adjusted. 5. Close the belt guard door. 6. Plug the motor pigtail in, twisting to lock. Transporting the Machine - Two People When transporting ...

  • American Standard 70145A 11/00 - page 10

    Page 10 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Machine Set-Up To set-up your machine follow this procedure: 1. Familiarize yourself with the machine and read all danger, warning and caution statements. Make sure all operators of this machine have read this Owner's Manual. If they cannot read English, have the manual expla ...

  • American Standard 70145A 11/00 - page 11

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 11 How to Operate the Machine DANGER: Sanding/finishing wood floors can create an environment that can be explosive. Cigarette lighters, pilot lights and any other source of ignition can create an explosion when active during a sanding session. All sources of ignition should be extin ...

  • American Standard 70145A 11/00 - page 12

    Page 12 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Figure 11 To operate the machine follow this procedure: 1. Install the operator's belt as follows: a. Position the operator's belt around waist. b. Cross the straps at the waist. See figure #11. c . Slide the belt loop end over the handle on the control lever side. Adjus ...

  • American Standard 70145A 11/00 - page 13

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 13 A. First pass forward, right to left. C. Second pass forward, overlap ½ the drum width. D. Second pass reverse, retrace second path forward, etc.....for the entire room. B. First pass reverse, retrace same path. E. Work the remaining unsanded floor in the same fashion, right to l ...

  • American Standard 70145A 11/00 - page 14

    Page 14 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Sanding Cuts and Sandpaper Initial Cut The purpose of the initial cut is to remove old finish and gross imperfections on the floor surface. The sanding equipment should be adjusted to heavy sanding pressure setting and a coarse abrasive belt should be used. If the surface is sever ...

  • American Standard 70145A 11/00 - page 15

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 15 Sander Adjustment Procedures DANGER: Electrocution could occur if main- tenance and repairs are performed on a unit that is not properly dis- connected from the power source. Disconnect the power supply be- fore attempting any maintenance or service. DANGER : Moving parts of this ...

  • American Standard 70145A 11/00 - page 16

    Page 16 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Figure 15 Leveling To adjust the machine leveling follow this procedure: 1. Locate the leveling screw. See figure #15. The leveling screw is located towards the rear of the chassis beneath the sanding pressure knob. 2. Tighten the leveling screw (compress the leveling spring) to s ...

  • American Standard 70145A 11/00 - page 17

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 17 Routine Maintenance The following items need to be periodically inspected and maintained to keep your sander in good working condition. Sanding Chamber Periodically blow out the sanding chamber to prevent large accumulations of debris which could interfere with the performance of ...

  • American Standard 70145A 11/00 - page 18

    Page 18 AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual P ROBLEM C AUSE A CTION Chatter T roubleshooting Drive belts slip. Insufficient tension. Tension drive belt as described in (Squeaking or squealing sound) adjustment procedures. Worn belts. Replace belts. Squealing, growling or grinding Damaged and/or worn bearing. Remove drive be ...

  • American Standard 70145A 11/00 - page 19

    AMERICAN SANDERS TECHNOLOGY Classic 8 Operator's Manual Page 19 Burning or glazing. Dull abrasive. Replace abrasive. Excessive sanding pressure. Decrease sanding pressure setting. Fig. #14, page 13. Too fine of an abrasive. Use coarser abrasive. Slow cutting. Dull abrasive. Replace abrasive. Too fine of an abrasive belt. Use a coarser abrasive ...

Fabbricante American Standard Categoria Sander

I documenti che otteniamo dal fabbricante del dispositivoAmerican Standard 70145A 11/00 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici American Standard
- manuali per l’uso 70145A 11/00
- schede prodotto American Standard
- opuscoli
- o etichette energetiche American Standard 70145A 11/00
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso American Standard 70145A 11/00.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione American Standard 70145A 11/00, manuali di manutenzione, brevi manuali o manuali utente American Standard 70145A 11/00. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto American Standard 70145A 11/00.

Manuali per l’uso simili

Manuale completo del dispositivo American Standard 70145A 11/00, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare American Standard 70145A 11/00 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti American Standard 70145A 11/00.

Il manuale per l’uso completo American Standard, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale American Standard 70145A 11/00 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice American Standard 70145A 11/00, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per American Standard 70145A 11/00 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo American Standard 70145A 11/00 - che ci dovrebbe aiutare nei primi passi durante l'uso American Standard 70145A 11/00
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del American Standard 70145A 11/00
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio American Standard 70145A 11/00 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su American Standard 70145A 11/00?

Utilizza il modulo sottostante

Se non hai risolto il problema con American Standard 70145A 11/00 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con American Standard 70145A 11/00 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)