Manuale per l’uso AMX MVP-WDS

36 pagine 1.27 mb
Scarica

Vai alla pagina of 36

Summary
  • AMX MVP-WDS - page 1

    Operation/Reference Guide Touch Panels & Accessories MVP-WDS Wall Docking Station for MVP-7500/8400 Modero ® ViewPoint ® Wireless Touch Panels Last Revised: 12/13/200 7 ...

  • AMX MVP-WDS - page 2

    AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under n ormal use for three (3) years from the date of purchase fr om AMX, with the following exceptions: • Electroluminescent and LCD Control P ane ls are warranted for three (3) years, except for the display and touch overlay componen ...

  • AMX MVP-WDS - page 3

    FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the followi ng two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding inte rference that may cause undesi red operation. Federal Communications Commission (FCC) Statement Th ...

  • AMX MVP-WDS - page 4

    ...

  • AMX MVP-WDS - page 5

    Table of Contents i MVP-WDS Wall Docking Station for MVP Panels Table of Contents MVP-WDS Wall Docking Station & CB-MVPWDS Con duit Box ........................... 1 Overview .............................. ......................... ................... ......................... ............... 1 Specification s .............. ............. ..... ...

  • AMX MVP-WDS - page 6

    ii MVP-WDS Wall Docking Station for MVP Panels Table of Contents ...

  • AMX MVP-WDS - page 7

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 1 MVP-WDS Wall Docking Station for MVP Panels MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box Overview The MVP-WDS W all/Flush Mount Docking Station (FIG. 1) pro vides a surface-installed docking location. MVP-WDS stations use a security latch to secure the panel to the docking stati ...

  • AMX MVP-WDS - page 8

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 2 MVP-WDS Wall Docking Station for MVP Panels Specifica tions MVP-WDS Specifications Dimensions (HWD): • 8.59" x 12.66" x 3.40" (21.82 cm x 32.16 cm x 8.64 cm) Note : Always use the cutout/installat ion dimensions for the MVP-WDS when installing this unit into various surface ...

  • AMX MVP-WDS - page 9

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 3 MVP-WDS Wall Docking Station for MVP Panels MVP-WDS docking station co nnector locations FIG. 2 shows the layout of the connectors on th e right side of the MVP-WDS. LED Indicators The two LEDs located within the security release pushbutton on the front panel (FIG. 1) indicate battery and c ...

  • AMX MVP-WDS - page 10

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 4 MVP-WDS Wall Docking Station for MVP Panels Installation MVP-WDS wall-docking stations can be installed either the CB-MVPWDS or othe r solid surface en vironment using one of the two mounting o ptions: drywall clips or solid surface s cr ews, as described in the following sub-sections. Inst ...

  • AMX MVP-WDS - page 11

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 5 MVP-WDS Wall Docking Station for MVP Panels 2. Using either nails or screws, fasten the conduit box to the stud through the fiv e Stud Fastening Holes. 3. Remove the wiring knockouts from the right side of the conduit box to accommodate cabling to the MVP-WDS. 4. Thread the USB and Power ca ...

  • AMX MVP-WDS - page 12

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 6 MVP-WDS Wall Docking Station for MVP Panels 4. Close the battery cov er and disconnect the power connector to remo ve po wer from the unit and maintain the support cradle in the forward position. 5. Remov e the two #6-32 F aceplate Security Screws from the top rim of the faceplate, using a ...

  • AMX MVP-WDS - page 13

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 7 MVP-WDS Wall Docking Station for MVP Panels 8. Press down on the Security Latch to allow it to go through the top op ening. 9. Grasp the top rim of the faceplate and carefully slide it over the cradle (at an angle) until the faceplate is completely removed from the WDS (FIG. 8). Once the fa ...

  • AMX MVP-WDS - page 14

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 8 MVP-WDS Wall Docking Station for MVP Panels Installing the MVP-WDS in a CB-MVPWDS Conduit Box  The conduit box must be mounted prior to continuing this section. Refer to the Installing the CB-MVPWDS Conduit Box section on page 4 for detailed pre-wall installation instructions.  The fa ...

  • AMX MVP-WDS - page 15

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 9 MVP-WDS Wall Docking Station for MVP Panels Installing the MVP -WDS Using Expansion Clips Expansion clips are mounted through the fou r ov al holes located along the rim of the MVP-WD S. As the screw is tightened, the clip bends to ward the inser tion hole and into the wall. This bending cr ...

  • AMX MVP-WDS - page 16

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 10 MVP-WDS Wall Docking Station for MVP Panels 5. Carefully insert the main unit (with expansion clip s) into the cutout so that the Mounting T abs on the MVP-WDS lie flush against the wall. FIG. 10 MVP-WDS Wall Mount cutout dim ensions using expansion clips FIG. 11 MVP-WDS installation confi ...

  • AMX MVP-WDS - page 17

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 11 MVP-WDS Wall Docking Station for MVP Panels 6. T ighten all four drywall clip sets (scre ws and clips) until both Mounting T abs are securely fastened and flush against the wall. 7. Follo w the steps outlined in the Replacing the F aceplate on the MVP-WDS section on page 13 to angle the MV ...

  • AMX MVP-WDS - page 18

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 12 MVP-WDS Wall Docking Station for MVP Panels  V erify that the terminal end of the power cable is not connected to a po wer source before plugging in the 2-pin po wer connector .  The USB connectors can be from either a USB extension cable, or a wireless USB RF transmitter . 4. T est ...

  • AMX MVP-WDS - page 19

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 13 MVP-WDS Wall Docking Station for MVP Panels Replacing the Fa ceplate on the MVP-WDS 1. T emporarily apply power to the MVP-WDS by connecting th e terminal end of the power cable to the power supply . 2. Press the Cradle Activ ation Pushbutton (located in side the MVP-WDS battery compartmen ...

  • AMX MVP-WDS - page 20

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 14 MVP-WDS Wall Docking Station for MVP Panels Initially , both blue LEDs illuminate and remain dim (indic ating that the power is being supplied to the MVP-WDS). Using the 3.5mm mini-Ph oenix Connector for Power T o use the 2-pin 3.5 mm mini-Phoenix con nector for use with a 12 VDC-complian ...

  • AMX MVP-WDS - page 21

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 15 MVP-WDS Wall Docking Station for MVP Panels  If a USB keyboard has been connected, only on-screen keyboards and ke ypads will reflect any external ke ystrokes sent from the external USB keyboard. T o be detected by the docking station, USB input devices (keyboard / mouse) must be plugge ...

  • AMX MVP-WDS - page 22

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 16 MVP-WDS Wall Docking Station for MVP Panels  When the MVP is properly docked, the fo llow ing message is displayed on the pane l (FIG. 17).  Proper docking and communication can be verif ied via the on-screen system message, or the illuminated Docking Status button on the Protect Set ...

  • AMX MVP-WDS - page 23

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 17 MVP-WDS Wall Docking Station for MVP Panels 5. Lift the panel off the alignment guide pins and remove it from the support cradle. Undock-<USER> Stri ng When the MVP is removed from the docking station (undocked), the undock-<user> string is sent to the NetLinx Master .  If t ...

  • AMX MVP-WDS - page 24

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 18 MVP-WDS Wall Docking Station for MVP Panels Installing the MVP-WDS-SK Silver Conversion Kit The VP-WDS-SK Silver Conv ersion Kit (FG5965-22) contains the following components:  One Silver Cradle Bezel/Faceplate (60-5965-20SL)  One Silver Cradle Pi vot ( Support Cr adle ) (60-5965-21S ...

  • AMX MVP-WDS - page 25

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 19 MVP-WDS Wall Docking Station for MVP Panels 7. Disconnect the 2-pin mini-Phoenix conne ctor from the side of the docking station to remove po wer from the unit and maintain the support cradle in this angled position. 8. Close the battery cov er . 9. Remov e the two #6-32 Faceplate Security ...

  • AMX MVP-WDS - page 26

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 20 MVP-WDS Wall Docking Station for MVP Panels 14. Press downward on the Security Latch (towards the pushb utton) to get it to go through the top opening and allow the faceplate’ s remov al. 15. Grab the top rim of the faceplate and carefully slid e it o ver the cradle (at an angle) until t ...

  • AMX MVP-WDS - page 27

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 21 MVP-WDS Wall Docking Station for MVP Panels 4. Carefully remov e the cradle piv ot’ s attachment screw and place it aside for later re-attachment. 5. Carefully slide the black piv ot cradle combo unit (battery cover/support cradle) up from the metallic housing and use the screwdri ver to ...

  • AMX MVP-WDS - page 28

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 22 MVP-WDS Wall Docking Station for MVP Panels 8. Carefully place the first circuit board aside and rota te the black piv ot combo unit over to expose the second circuit board attached to the backside of the u nit ( B in FIG. 24). 9. Carefully remove this second board by unscrewing the three ...

  • AMX MVP-WDS - page 29

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 23 MVP-WDS Wall Docking Station for MVP Panels 5. Use the scre wdriv er to install one of the previous ly remo ved MVP Support Cradle Securing screws to the securing plate (shown in FIG. 23 on pa ge 21). 6. Carefully slide the entire silver battery pi vot combo unit into the black WDS metal h ...

  • AMX MVP-WDS - page 30

    MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box 24 MVP-WDS Wall Docking Station for MVP Panels  Open the Battery Compartment by pressing down on the Battery Compartment Latch and then pulling the cov er outwards.  Press the Cradle Acti vation pushb utton (the small recessed white b utton lo cated near the pins in Battery Slot #2) to ...

  • AMX MVP-WDS - page 31

    Upgrading the Docking Station Firmw are 25 MVP-WDS Wall Docking Station for MVP Panels Upgrading the Docking Station Firmware The following accessory de vices are firmware upgradeable:  MVP-TDS T able T op Dockin g Station ( FG5965-10 )  MVP-WDS W all/Flush Mount Docking Station - Black ( FG5965-11 )  MVP-WDS W all/Flush Mount Docking Stat ...

  • AMX MVP-WDS - page 32

    Upgrading the Docking Station Firmware 26 MVP-WDS Wall Docking Station for MVP Panels Step 2: Upgrade t he Docking Station firmware v ia USB 1. Configure the panel for a USB Connection T ype. 2. Prepare NetLinx Studio for comm unication to the panel v ia a V irtual Master . 3. After the Communication V erification dialog windo w verifies acti ve co ...

  • AMX MVP-WDS - page 33

    Upgrading the Docking Station Firmw are 27 MVP-WDS Wall Docking Station for MVP Panels 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r eboot of the panel can take up 30 seconds after the f irmwar e pr ocess has finished. 11. Click Send to begin the transfer . The fil ...

  • AMX MVP-WDS - page 34

    Upgrading the Docking Station Firmware 28 MVP-WDS Wall Docking Station for MVP Panels Although firmware u pgrades can be don e over wirele ss Ethernet; it is recommended that firmware KIT files be transfer red over a direct USB connection and only when the panel is connected to a power supply . If battery power or wireless connection fails during a ...

  • AMX MVP-WDS - page 35

    Upgrading the Docking Station Firmware 29 M VP-WDS Wall Docking Station for MVP Pan els ...

  • AMX MVP-WDS - page 36

    12/07 © 2007 AMX. All rights reserved. AMX a nd the AMX logo are regist ered trademarks of AMX. AMX rese rves the right to alter specific ations without no tice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support ? ...

Fabbricante AMX Categoria Car Video System

I documenti che otteniamo dal fabbricante del dispositivoAMX MVP-WDS possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici AMX
- manuali per l’uso MVP-WDS
- schede prodotto AMX
- opuscoli
- o etichette energetiche AMX MVP-WDS
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso AMX MVP-WDS.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione AMX MVP-WDS, manuali di manutenzione, brevi manuali o manuali utente AMX MVP-WDS. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto AMX MVP-WDS.

Manuale completo del dispositivo AMX MVP-WDS, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare AMX MVP-WDS dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti AMX MVP-WDS.

Il manuale per l’uso completo AMX, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale AMX MVP-WDS - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice AMX MVP-WDS, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per AMX MVP-WDS che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo AMX MVP-WDS - che ci dovrebbe aiutare nei primi passi durante l'uso AMX MVP-WDS
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del AMX MVP-WDS
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio AMX MVP-WDS in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su AMX MVP-WDS?

Utilizza il modulo sottostante

Se non hai risolto il problema con AMX MVP-WDS con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con AMX MVP-WDS è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)