Italiano dropdown-ico

Manuale per l’uso Behringer SHARK DSP110

25 pagine 1.37 mb
Scarica

Vai alla pagina of 25

Summary
  • Behringer SHARK DSP110 - page 1

    SHARK ® DSP110 Userss Manual Version 1.2 April 2001 www.behringer.com ENGLISH ...

  • Behringer SHARK DSP110 - page 2

    2 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 3

    3 SHARK DSP1 10 1. INTRODUCTION Thank you very much for expressing your confidence in BEHRINGER products by purchasing the SHARK DSP110. + This manual first describes the terminology used, so that you can fully understand the DSP110 and its functions. Please read the manual carefully and keep it for future reference. 1.1 The concept With the SHARK ...

  • Behringer SHARK DSP110 - page 4

    4 SHARK DSP1 10 Fig. 1.1: T ypical feedback loop 1. 2 Before you begin Your SHARK was carefully packed in the factory and the packaging is designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the carton and its contents for any signs of physical damage, which may have occurred during transit. + If ...

  • Behringer SHARK DSP110 - page 5

    5 SHARK DSP1 10 Be sure that there is enough air space around the unit for cooling and please do not place the SHARK on high-temperature devices such as power amps, etc. to avoid overheating. Please use the enclosed power supply to connect the unit to the mains. The supply complies with all applicable safety standards. + Please note that all units ...

  • Behringer SHARK DSP110 - page 6

    6 SHARK DSP1 10 1. 3 Control elements Fig. 1.2: Front p anel control elements of the DSP1 10 1 The CLIP LEVEL METER shows you whether or not the digital circuitry is driven correctly. Any corrections can be made with the CLIP LEVEL control . Be sure that the CLIP LED wont light up. 2 The CLIP LEVEL control lets you adapt the internal gain optima ...

  • Behringer SHARK DSP110 - page 7

    7 SHARK DSP1 10 4 The 4-digit DISPLAY reads the absolute values of the adjusted parameters. 5 The FB-D FILTER STATUS LEDs display the status of each of the 12 individual filters. The SHARK uses four different filter modes: s Disabled filters (which can be re-enabled with the ACTIVE button). When a filter is off, its LED is not lit. s Free filters w ...

  • Behringer SHARK DSP110 - page 8

    8 SHARK DSP1 10 9 The LOW CUT button lets you enter the high pass filters cut-off frequency (20 to 150 Hz). When set to OFF the filter is inoperative. The control and Hz LEDs light up while you are entering a value. Use the UP/DOWN buttons to edit. Pressing the LOW CUT button for a longer time (please wait, until all five parameter LEDs li ...

  • Behringer SHARK DSP110 - page 9

    9 SHARK DSP1 10 + When both FILTER LED and display stop flashing, the FILTER LEARN function has been completed. Press the FILTER key to cancel the function. After a short delay, the unit returns to the FILTER menu. The FILTER LEARN function generates short feedback-causing signals that are sent back to the DSP110s input, where feedbacks are dete ...

  • Behringer SHARK DSP110 - page 10

    10 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 11

    11 SHARK DSP1 10 20 This is the SHARKs balanced JACK input, which is wired in parallel to the XLR input. 21 Use the INPUT LEVEL switch to select the input sensitivity (microphone or line levels). In LINE mode, you can use the CLIP LEVEL control to adapt the internal level settings to the digital circuitry. Please make sure that the CLIP-LED will ...

  • Behringer SHARK DSP110 - page 12

    12 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 13

    13 SHARK DSP1 10 2.1.3 Connection between mixing console and power amplifier When you use the SHARK as a Delay Line unit for speaker systems placed at various positions (see chapter 2.3), you should connect the SHARK between the consoles output and the input of the power amp driving the delayed speakers. ...

  • Behringer SHARK DSP110 - page 14

    14 SHARK DSP1 10 2.1.4 The SHARK used in the monitor path Inserting the DSP110 in the monitor path of your mixing console gives you utmost protection against unwanted feedback. Monitor paths are particularly susceptible to feedback, because on stage there are usually several microphones and speakers placed close to each other. Especially vocal micr ...

  • Behringer SHARK DSP110 - page 15

    15 SHARK DSP1 10 Fig. 2.4: T wo SHARKs in the monitor path 2.1.5 The SHARK used in single channels and subgroups Whenever you want to make sure that wanted feedback such as the feedback sounds produced by a guitar wont be removed, you should insert one or several DSP110 into feedback-prone single channels (e.g. vocals) or subgroups of your ...

  • Behringer SHARK DSP110 - page 16

    16 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 17

    17 SHARK DSP1 10 2. 2 The Feedback Destroyer in the SHARK The SHARK identifies feedback by splitting the entire frequency spectrum (20 Hz to 20 kHz) into sections of 1/60 of an octave and determining the level of each of these bands. The values calculated are then referenced to the level of the overall signal. The resulting level difference determi ...

  • Behringer SHARK DSP110 - page 18

    18 SHARK DSP1 10 2. 3 The integrated Delay In addition to speakers on or near the stage, major-scale installations often have speaker groups positioned at a distance to the stage or flown above the audience, in order to provide listeners away from the stage with direct sound. However, since sound needs some time to travel around (343.6 m/sec at 20? ...

  • Behringer SHARK DSP110 - page 19

    19 SHARK DSP1 10 between microphones, without producing any unpleasant side effects. A typical Gate application is the processing of vocal tracks. Especially when using a Compressor, the distance between microphone and singer is critical: as the distance increases, more and more disturbing background noise is picked up. Use the Gate function to fad ...

  • Behringer SHARK DSP110 - page 20

    20 ...

  • Behringer SHARK DSP110 - page 21

    21 SHARK DSP1 10 Unbalanced use of mono 1/4" jack plugs Ring Balanced use of stereo 1/4" jack plugs Balanced use with XLR connectors 1 2 3 2 1 3 ...

  • Behringer SHARK DSP110 - page 22

    22 SHARK DSP1 10 4. SPECIFICATIONS AUDIO INPUTS Connectors XLR and 1/4" jack T ype RF filtered, servo-balanced input Impedance 6 kOhms balanced, 3 kOhms unbalanced Nominal Operating Level microphone or line level source (switchable) Max. Input Level +19 dBu at microphone level and line level AUDIO OUTPUTS Connectors XLR and 1/4" jack T yp ...

  • Behringer SHARK DSP110 - page 23

    23 SHARK DSP1 10 5. RACKMOUNT (OPTIONAL) With the available rackmount (optional) you have the possibility to place five SHARKs on two units of space in your rack. + Before you begin with the work, please disconnect the Power Supply Units from the SHARKs! To mount the SHARKs on the rackmount you should use the supplied screws (type M3). You need two ...

  • Behringer SHARK DSP110 - page 24

    24 SHARK DSP1 10 Fig. 5.1: Inst allation of the DSP1 10 on the available rackmount (optional) + Please, only use the supplied screws to install the SHARKs on the rackmount. Longer or thicker screws can damage the electronics inside of the device and doing so will void your warranty rights. You will need 2 units of space for the DSP110 rackmount. Fo ...

  • Behringer SHARK DSP110 - page 25

    25 SHARK DSP1 10 6. WARRANTY 6. WARRANTY § 1 WARRANTY CARD/ONLINE REGISTRATION To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in ...

Fabbricante Behringer Categoria Power Supply

I documenti che otteniamo dal fabbricante del dispositivoBehringer SHARK DSP110 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Behringer
- manuali per l’uso SHARK DSP110
- schede prodotto Behringer
- opuscoli
- o etichette energetiche Behringer SHARK DSP110
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Behringer SHARK DSP110.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Behringer SHARK DSP110, manuali di manutenzione, brevi manuali o manuali utente Behringer SHARK DSP110. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Behringer SHARK DSP110.

Manuali per l’uso simili

Manuale completo del dispositivo Behringer SHARK DSP110, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Behringer SHARK DSP110 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Behringer SHARK DSP110.

Il manuale per l’uso completo Behringer, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Behringer SHARK DSP110 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Behringer SHARK DSP110, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Behringer SHARK DSP110 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Behringer SHARK DSP110 - che ci dovrebbe aiutare nei primi passi durante l'uso Behringer SHARK DSP110
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Behringer SHARK DSP110
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Behringer SHARK DSP110 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Behringer SHARK DSP110?

Utilizza il modulo sottostante

Se non hai risolto il problema con Behringer SHARK DSP110 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Behringer SHARK DSP110 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)