Manuale per l’uso Aiwa 586IVX

68 pagine 0.72 mb
Scarica

Vai alla pagina of 68

Summary
  • Aiwa 586IVX - page 1

    586IV X Re v . 2 + System Boar d Use r ’ s Manua l - 32970703 - ...

  • Aiwa 586IVX - page 2

    FCC Statement on Class B This equipment has been tested and found to comply with the limits fo r a Class B digital device, pursuant to Part 15 of the FCC rules. Thes e limits are designed to provide reasonable protection against harmful in - terference when the equipment is operated in a residential installation . This equipment generates, uses and ...

  • Aiwa 586IVX - page 3

    Table of Content s Chapter 1: Introductio n ............................................................ 5 Features and Specification s .................................................. 6 Package Checklis t .............................................................. 8 Chapter 2: Hardware Installatio n ........................................... ...

  • Aiwa 586IVX - page 4

    4 Save & Exit Setu p ........................................................ 5 3 Exit Without Savin g ....................................................... 5 4 Desktop Management Interface (DMI ) .................................... 5 6 System Error Repor t .......................................................... 5 4 IDE Device Driver s .. ...

  • Aiwa 586IVX - page 5

    5 The 586IVX is a Pentiu m  processor-class system board supportin g Intel Pentiu m  Processor with MMX Technology and Intel Pentiu m  pro - cessors running at 75MHz, 90MHz, 100MHz, 120MHz, 133MHz, 150MHz, 166MHz and 200MHz frequencies. The 58 6 IV X also support s Cyri x  6x86 ™ P120+/P133+/P150+/P166+ and AMD-K5 PR75/PR90 / PR100/PR ...

  • Aiwa 586IVX - page 6

    6 Features and Specification s Processo r • Intel Pentiu m  Processor with MM X  Technology - 166/20 0 • Intel Pentiu m  75/90/100/120/133/150/166/200MH z • Future Pentiu m  OverDrive processo r • Cyri x  6x86 ™ P120+/P133+/P150+/P166 + • AMD-K5 PR75/PR90/PR100/PR120/PR133/PR16 6 Chipse t • Intel 82430VX PCIse t Cache M ...

  • Aiwa 586IVX - page 7

    7 • Soft Power supporte d PCI IDE Interfac e • PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up t o 16.6MB/sec. ) • DMA Mode 2 Bus Master IDE (data transfer rate up to 22.2MB/sec. ) • Bus mastering reduces CPU utilization during disk transfe r • ATAPI IDE CD-ROM supporte d Integrated I/ O • Two NS16C550A-compatible high speed U ...

  • Aiwa 586IVX - page 8

    8 Package Checklis t The 586IVX package contains the following items : • The 586IVX system boar d • The 586IVX user ’ s manua l • One 40-pin IDE hard disk cabl e • One 34-pin floppy disk drive cabl e • One IDE driver diskett e • Five spare jumper s If any of these items are missing or damaged, please contact you r dealer or sales repr ...

  • Aiwa 586IVX - page 9

    9 Chapter 2 Hardware Installatio n This chapter summarizes the steps to install the 586IVX system boar d into your system unit. It also includes a description of the area in whic h you must work and directions for memory installation. Before installin g the system board, obtain the memory you plan to install. Refer to th e System Memory section for ...

  • Aiwa 586IVX - page 10

    10 Static Electricity Precaution s 1 . To prevent electrostatic build-up, leave the board in its anti-stati c bag until you are ready to install it . 2 . Wear an antistatic wrist strap . 3 . Do all preparation work on a static-free surface with the syste m board components facing up . 4 . Hold the system board by its edges only. Be careful not to t ...

  • Aiwa 586IVX - page 11

    11 2 . Remove the system unit cover. Refer to the manufacturer ’ s instruc - tions if necessary . 3 . Detach all connectors from the old system board and remove ex - pansion cards seated in any expansion slots . 4 . Loosen the screws holding the original system board and remov e the board from the system. Save the screws . 5 . Remove the 586IVX f ...

  • Aiwa 586IVX - page 12

    12 Board La you t square denotes pin 1 U29 ISA Slot 4 ISA Slot 3 ISA Slot 2 ISA Slot 1 PCI Slot 4 PCI Slot 3 PCI Slot 2 PCI Slot 1 S oc k e t 7 S oc k e t 7 Pin 1 1 2 4 3 JP7 1 5 6 2 1 5 6 2 JP2 JP3 1 2 4 3 JP4 JP5 J8 Primary IDE Secondary IDE J11 J12 82438VX J10 Floppy JP12 JP 11 JP10 J9 ATX Power Connector JP1 J3 BIOS 82371S B 82438VX SRA M Batte ...

  • Aiwa 586IVX - page 13

    13 Jumper s JP2-JP5, JP7, JP10-JP1 2 Intel, Cyrix and AMD processor s JP1 - CMOS clea r JP13 - Password clea r Socket s SM1 to SM4 - SIMM socket s U29 - ZIF socke t J 2 - USB 1 por t J 4 - USB 2 por t J 8 - IrDA connecto r J 9 - Fan connecto r J1 0 - FDD connecto r J1 1 - Primary IDE HDD connecto r J1 2 - Secondary IDE HDD connecto r J1 3 - ATX pow ...

  • Aiwa 586IVX - page 14

    14 SIM M The SIMM (Single In-line Memory Module) sockets are divided into tw o banks on the system board, Bank 0 and Bank 1. Each bank consists o f 2 SIMM sockets . You will need either 2 or 4 pieces of SIM modules, depending on th e amount of memory you intend to install. The system board will not wor k if you install 1 or 3 pieces. Make sure you ...

  • Aiwa 586IVX - page 15

    15 The table below summarizes the bank locations and modules neede d for the corresponding memory sizes . Memory Siz e 8M B 8M B 16M B 16M B 16M B 24M B 24M B 32M B 32M B 40M B 40M B 48M B 48M B 64M B 64M B 64M B 72M B 72M B 80M B 80M B 96M B 96M B 128M B Bank 0 SIMM 1 1MBx3 2 — 2MBx3 2 — 1MBx3 2 1MBx3 2 2MBx3 2 4MBx3 2 2MBx3 2 1MBx3 2 4MBx3 2 ...

  • Aiwa 586IVX - page 16

    16 Cache Memor y The 586IVX system board can support 256KB pipeline burst, direct ma p write-back cache SRAM. Your system board may come with 256K B cache mounted at locations U11 and U17 of the system board . 1 . Position the SIMM above the socket with the “ notch ” in the modul e aligned with the “ key ” on the socket . 2 . Seat the modul ...

  • Aiwa 586IVX - page 17

    17 CPU Installatio n The 586IVX allows for easy installation of CPUs. Make sure all jumpers ar e set correctly before applying power or you may damage the CPU or syste m board. Use a needle-nosed plier to move the jumpers if necessary . Jumpers JP10, JP11 and JP12 are used to set the external bus clock o f your processor. Refer to the following pag ...

  • Aiwa 586IVX - page 18

    18 Jumper Settings for Intel Processor s Voltage s 2.7 V 2.8 V 2.9 V 3.3V * (VR/STD ) 3.5 V (VRE ) JP 2 1-3, 2-4 O n 1-3, 2-4 O n 1-3, 2-4 O n 3-5, 4-6 O n 3-5, 4-6 O n JP 3 1-2 O n 3-4 O n 5-6 O n 3-4 O n 3-4 O n JP 4 3-4 O n 3-4 O n 3-4 O n 3-4 O n 1-2 O n JP 7 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 O n 1-2, 3-4 O n Intel Processor s ...

  • Aiwa 586IVX - page 19

    19 Jumper Settings for Cyrix 6x86 Processor s JP1 0 1-2 O n 2-3 O n 1-2 O n 1-2 O n JP1 1 1-2 O n 1-2 O n 2-3 O n 1-2 O n JP1 2 1-2 O n 1-2 O n 1-2 O n 2-3 O n JP 5 3-5 On, 2-4 O n Cyrix CPU s P120 + P133 + P150 + P166 + Ext. Bu s CL K 50MH z 55MH z 60MH z 66MH z Cyrix CPU s P120+/P133+ / P150+/P166 + Freq. Rati o 2 x Voltage s 2.7 V 2.8 V 2.9 V 3. ...

  • Aiwa 586IVX - page 20

    20 Jumper Settings for AMD-K5 Processor s Voltage s 2.7 V 2.8 V 2.9 V 3.3V * (VR/STD ) 3.5 V (VRE ) JP 2 1-3, 2-4 O n 1-3, 2-4 O n 1-3, 2-4 O n 3-5, 4-6 O n 3-5, 4-6 O n JP 3 1-2 O n 3-4 O n 5-6 O n 3-4 O n 3-4 O n JP 4 3-4 O n 3-4 O n 3-4 O n 3-4 O n 1-2 O n JP 7 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 Of f 1-2, 3-4 O n 1-2, 3-4 O n P-Ratin g PR7 5 P ...

  • Aiwa 586IVX - page 21

    21 Installing Upgrade CPU s The 586IVX is equipped with a 321-pin Zero Insertion Force (ZIF) socket at location U29 of the system board. Refer to page 12 for th e location of the ZIF socket. This socket is designed for easy removal o f an old CPU and easy insertion of an upgrade CPU. The ZIF socke t allows you to carefully place the new CPU into it ...

  • Aiwa 586IVX - page 22

    22 Lifting the Handl e 2 . Once the lever is completely up, remove the old CPU carefully b y lifting it straight out of the socket. You are now ready to insert th e new CPU . 3 . Position the CPU above the ZIF socket. Make sure pin 1 of th e CPU is aligned with pin 1 of the socket. Lower the chip until th e pins are inserted properly in their corre ...

  • Aiwa 586IVX - page 23

    23 4 . Push the handle down until the handle locks into place. The to p plate will slide forward. You will feel some resistance as pressur e starts to secure the CPU in the socket. This is normal and will no t damage the CPU. However, if the handle is not completely closed , damage to the CPU and/or system board may result . Positioning the CPU Abo ...

  • Aiwa 586IVX - page 24

    24 least 3 of 4 sides of the processor and heatsink must be at least 0. 2 inches. All cables (for floppy drive, hard drive, CD-ROM, etc.) must b e routed clear of the CPU and its airspace . Fan Exhaus t The CPU must be kept cool by using a fan with heatsink. The tempera - ture of the air entering the fan/heatsink cannot exceed 4 5 o C (11 3 o F) . ...

  • Aiwa 586IVX - page 25

    25 Built-in Port s The 586IVX system board is equipped with two serial ports, one paralle l printer port, one shrouded floppy disk header, two shrouded IDE har d disk headers, and two USB ports. Refer to page 12 for the locations o f the built-in connectors and pin 1 of those connectors . PS/ 2 Mous e PS/ 2 K/ B USB 1 USB 2 Parallel Printe r COM 2 ...

  • Aiwa 586IVX - page 26

    26 I/O Addres s 3BC-3BE He x 378-37 A Hex (default ) 278-27 A He x Serial Port s The 586IVX is equipped with two serial ports at locations CN5 (COM 2 ) and CN6 (COM 1) of the system board. These built-in serial ports ar e RS-232C asynchronous communication ports with 16C550A-compatibl e UARTs that can be used with modems, serial printers, remote di ...

  • Aiwa 586IVX - page 27

    27 IDE Hard Disk Interfac e The 586IVX system board is equipped with two shrouded PCI ID E headers that will interface four Enhanced IDE (Integrated Drive Elec - tronics) hard disk drives . Note : Only Enhanced IDE hard drives or ATAPI CD-ROMs can be connecte d to the IDE interface . Connecting the IDE Hard Disk Interfac e To prevent improper IDE c ...

  • Aiwa 586IVX - page 28

    28 Heade r Note : An IDE cable with a standard 40-pin connector (without the keyin g mechanism) can be installed in the shrouded PCI IDE header. Be ex - tremely careful to match the colored edge of the ribbon with pin 1 of th e header . Connecting the Hard Disk Cabl e 1 . If you are connecting two hard drives, install the 40-pin connector o f the I ...

  • Aiwa 586IVX - page 29

    29 We recommend that you use Enhanced IDE hard drives from the sam e manufacturer. In a few cases, drives from two different manufacturer s will not function properly when used together. The problem lies in th e hard drives, not the 586IVX system board . Preparing an IDE Drive for Us e IDE disk drives are already low-level formatted, with any bad-t ...

  • Aiwa 586IVX - page 30

    30 Installing Expansion Card s The 586IVX system board is equipped with 3 dedicated PCI slots, 3 dedicated 16-bit ISA slots and 1 shared PCI/ISA slot. All PCI slots ar e bus masters. Refer to page 12 for the locations of the expansion slots . ...

  • Aiwa 586IVX - page 31

    31 Chapter 3 Software Installatio n After you power up your system, the BIOS message appears on you r screen and the memory count begins . After the memory test, the following message will appear on the screen : Press DEL to enter setu p If the message disappears before you respond, restart your system o r press the “ Reset ” button located on ...

  • Aiwa 586IVX - page 32

    32 MODE Auto Auto Auto Auto Use the arrow keys to highlight the option you want and press <Enter> . The following describes each of these options . Note : The settings on the BIOS setup screens on the following pages are fo r reference only. Some of the settings will vary according to your system ’ s configuration and should not be referred ...

  • Aiwa 586IVX - page 33

    33 Dat e The date format is <day>, <month>, <date>, <year> . Da y Mont h Dat e Yea r Displays a da y , from Sunday to Saturda y Displays the month, from January to Decembe r Displays the date, from 1 to 3 1 Displays the yea r, from 1900 to 209 9 Tim e The time format is <hour>, <minute>, <second>. The time ...

  • Aiwa 586IVX - page 34

    34 Note : Choosing an incorrect type might cause your system to format the flopp y disk improperl y , and you will not be able to access your data . Drive A and Drive B These categories identify the types of floppy disk drives installed. Th e following are the options for drives A and B . Non e 360K, 5.25 in . 1.2M, 5.25 in . 720K, 3.5 in . 1.44M, ...

  • Aiwa 586IVX - page 35

    35 Vide o This category selects the type of video adapter used for the primar y system monito r. Although secondary monitors are supported, you do no t have to select the type in Setup. The default setting is EGA/VG A (BIO S default, Setup default) . EGA/VG A CGA 4 0 CGA 8 0 Mon o Enhanced Graphics Adapter/Video Graphics Arra y . For EGA , VGA, SVG ...

  • Aiwa 586IVX - page 36

    36 BIOS Features Setu p The BIOS Features Setup allows you to configure your system for basi c operation. Some entries are defaults required by the system board , while others, if enabled, will improve the performance of your system o r let you set some features according to your preference . Bas e Memor y Extende d Memor y Othe r Memor y This refe ...

  • Aiwa 586IVX - page 37

    37 ! WARNING ! Disk boot sector is to be modifie d Type “ Y ” to accept write or “ N ” to abort writ e Award Software, Inc . After seeing this message, if necessary, you will be able to run an anti - virus program to locate and remove the problem before any damage i s done . Many disk diagnostic programs which attempt to access the boot sec ...

  • Aiwa 586IVX - page 38

    38 A, C C, A CDROM, C, A C, CDROM, A The system will first search for a floppy drive and then a hard disk drive . The system will first search for a hard disk drive an d then a floppy drive . The system will first search for a CD-ROM drive, then a hard disk drive and then a floppy drive . The system will first search for a hard disk drive, then a C ...

  • Aiwa 586IVX - page 39

    39 Boot Up NumLock Statu s This allows you to determine the default state of the numeric keypad . By default, the system boots up with NumLock on . The function of the numeric keypad is the number keys . The function of the numeric keypad is the arrow keys . O n Of f Security Optio n This category allows you to limit access to your system and Setup ...

  • Aiwa 586IVX - page 40

    40 Enable d Disable d Video shadow is enabled . Video shadow is disabled . C8000-CBFFF Shadow to DC000-DFFFF Shado w These categories determine whether option ROMs will be copied t o RAM . Chipset Features Setu p This section gives you instructions on how to configure the syste m based on the specific features of the chipset. The chipset manages bu ...

  • Aiwa 586IVX - page 41

    41 Power Managemen t This category allows you to select the type (or degree) of power savin g by changing the length of idle time that elapses before each of th e following modes are activated: Doze Mode, Standby Mode, and Sus - pend Mode . No power management. Disables the Doze, Standby an d Suspend modes . Minimum power management. Doze Mode = 1 ...

  • Aiwa 586IVX - page 42

    42 Video Off Metho d This determines the manner in which the monitor is blanked . MODEM Use IR Q This category is used to set an IRQ channel (IRQ 3, 4, 5, 7, 9, 10 o r 11) for the modem installed in your system . Doze Mode, Standby Mode, Suspend Mode and HDD Power Dow n These Green PC power saving categories are user configurable onl y when the Pow ...

  • Aiwa 586IVX - page 43

    43 IRQ3-IRQ15 ( Wake Up Events in Doze & Standby and Powe r Down & Resume Events ) These are I/O events whose occurrence can prevent the system fro m entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything which occurs to a device which is configured as enabled, even when the ...

  • Aiwa 586IVX - page 44

    44 Resources Controlled B y The Award Plug and Play BIOS has the capacity to automatically con - figure all of the boot and Plug and Play compatible devices . The system will automatically detect the settings for you. Th e categories that follow will not be shown on the PNP/PCI Con - figuration screen . This allows you to set the IRQ/DMA (you have ...

  • Aiwa 586IVX - page 45

    45 Primary IDE INT# and Secondary IDE INT # The Primary and Secondary IDE INT# categories are used to select th e PCI interrupt (A, B, C, or D) that is associated with the connected har d drives . Load BIOS Default s The “ Load BIOS Defaults ” option loads the troubleshooting default val - ues permanently stored in the ROM chips. These settings ...

  • Aiwa 586IVX - page 46

    46 On-Chip Primary PCI IDE and On-Chip Secondary PCI ID E These categories allow you to enable or disable the primary and sec - ondary IDE controller. The default is Enabled. Select Disabled if yo u want to add a different hard drive controller . Integrated Peripheral s IDE HDD Block Mod e Enable d Disable d The IDE HDD uses the block mode. The sys ...

  • Aiwa 586IVX - page 47

    47 PCI Slot IDE 2nd Channe l This allows you to designate an IDE controller card inserted into one o f the PCI slots as your secondary IDE controller . The IDE controller card is designated as the secondary ID E controller . No IDE controller card occupying any of the PCI slots . Enable d Disable d Onboard FDD Controlle r Enables the onboard floppy ...

  • Aiwa 586IVX - page 48

    48 Uses the COM 2 serial port . HP mode IrDA . SHARP mode IrDA . Standar d HPSI R ASKI R Onboard Parallel Por t Selects the I/O address and IRQ for the onboard parallel port . Disables the onboard parallel port . 378H/IRQ 7 3BCH/IRQ 7 278H/IRQ 5 Disable d Parallel Port Mod e Selects the parallel port mode according to the type of printe r device co ...

  • Aiwa 586IVX - page 49

    49 Type in the password. You are limited to eight characters. When done , the message below will appear : Confirm Password : You are being asked to verify the password. Type in exactly the sam e password. If you type in a wrong password, you will be prompted t o enter the correct password again . To delete or disable the password function, highligh ...

  • Aiwa 586IVX - page 50

    50 ROM PCI/ISA BIOS CMOS SETUP UTILITY AW ARD SOFT WARE, INC. HARD DISKS TYPE SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE Primary Master: Select Primary Master Option (N=Skip): N OPTIONS SIZE CYLS HEAD RECOMP LANDZ SECTOR MODE 2 (Y) 853 827 32 0 1653 63 LBA 1 853 1654 16 65535 1653 63 Normal 3 853 827 32 65536 1653 63 Large Note: Some OS (like SCO-UNIX ...

  • Aiwa 586IVX - page 51

    51 If you set your HDD to Normal mode, the maximum accessible HDD wil l be 528 megabytes even though the physical size of the HDD may b e greater than that . LBA (Logical Block Addressing) Mod e LBA mode is a HDD accessing method to overcome the 528 megabyt e limitation. The number of cylinders, heads and sectors shown on th e screen may not be the ...

  • Aiwa 586IVX - page 52

    52 HDD Low Level Forma t The HDD Low Level Format utility is designed as a tool to save yo u time formatting your hard disk. It automatically looks for the necessar y information of the drive you selected. This utility also searches for ba d tracks and lists them for your reference. Highlight this option and pres s <Enter>. A screen similar t ...

  • Aiwa 586IVX - page 53

    53 Save & Exit Setu p When all the changes have been made, highlight “ Save & Exit Setup ” and press <Enter>. The message below will appear : Save to CMOS and Exit (Y/N)? N Type “ Y ” and press <Enter>. The modifications you have made will b e written into the CMOS memory, and the system will reboot. You wil l once again ...

  • Aiwa 586IVX - page 54

    54 Play BIOS. Additional information, such as ISA based peripherals, which may not be automatically detected, can be manually recorded i n the DMI pool by using the Add DMI menu. The DMI pool data is the n verified or updated whenever the system hardware or setup is altered . Running the DMI Utilit y To run the DMI utility, type: DMICFG.EXE. You ca ...

  • Aiwa 586IVX - page 55

    55 Edit DM I 1 . Use the ← o r → arrow keys to select the Edit DMI menu . 2 . Highlight the item on the left screen that you would like to edit b y using the ↑ or ↓ arrow keys, then press <Enter> . 3 . The cursor will move to the screen you select allowing you to edi t information. The screen will also display the auto-detected inform ...

  • Aiwa 586IVX - page 56

    56 System Error Repor t When the BIOS encounters an error that requires the user to correc t something, either a beep code will sound or a message will be dis - played in a box in the middle of the screen and the message, PRES S F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will b e shown in the information box at the bottom. Enter Setup to c ...

  • Aiwa 586IVX - page 57

    57 Error Message s One or more of the following messages may be displayed if the BIO S detects an error during the POST. This list indicates the error message s for all Awards BIOSes : CMOS BATTERY HAS FAILE D The CMOS battery is no longer functional. It should be replaced . CMOS CHECKSUM ERRO R Checksum of CMOS is incorrect. This can indicate that ...

  • Aiwa 586IVX - page 58

    58 Hard Disk(s) fail (08 ) Sector Verify failed . Keyboard is locked out - Unlock the ke y The BIOS detects that the keyboard is locked. Keyboard controller i s pulled low . Keyboard error or no keyboard presen t Cannot initialize the keyboard. Make sure the keyboard is attache d correctly and no keys are being pressed during the boot . Manufacturi ...

  • Aiwa 586IVX - page 59

    59 Chapter 4 T roubleshooting Checklis t This chapter of the manual is designed to help you with problems tha t you may encounter with your personal compute r . To efficiently troubleshoot your system, treat each problem individuall y . This is t o ensure an accurate diagnosis of the problem in case a problem ha s multiple causes . Some of the most ...

  • Aiwa 586IVX - page 60

    60 Hard Driv e Hard disk failure . 1 . Make sure the correct drive type for the hard disk drive has bee n entered in the BIOS . 2 . If the system is configured with two hard drives, make sure th e bootable (first) hard drive is configured as Master and the secon d hard drive is configured as Slave . Excessively long formatting period . 1 . If your ...

  • Aiwa 586IVX - page 61

    61 3 . Verify that the attached serial device works by attaching it to a seria l port that is working and configured correctl y . If the serial devic e does not work, either the cable or the serial device has a problem. I f the serial device works, the problem may be due to the onboard I/ O or the address setting . 4 . Make sure the COM port settin ...

  • Aiwa 586IVX - page 62

    62 SIM M 1MBx3 2 2MBx3 2 4MBx3 2 8MBx3 2 Bran d Fujits u OK I OK I NE C Micro n T I Micro n Micro n NE C Hitach i Fujits u Mitsubish i Hitach i NE C NE C NE C Chip Numbe r 81C1000A-7 0 M51440A-7 0 M511000B-7 0 424400-6 0 40447-6 0 TMS4400DJ-7 0 MT4C4007-70 (EDO ) MT4C4007-60 (EDO ) 4218165-60 (EDO ) 7400AS-7 0 8117400-7 0 422A06-7 0 5117400AS-7 0 4 ...

  • Aiwa 586IVX - page 63

    63 Memory Address Ma p Addres s Nam e Functio n 0000000 t o 640KB Syste m System Board Memor y 009FFF F Board RA M 00A0000 t o 128KB Vide o Reserved for Graphic s 00BFFF F Display Memor y Display Memor y 00C0000 t o 160KB I/ O Reserved for ROM o n 00E7FF F Expansion RO M I/O Adapter Car d 00E8000 t o 96KB ROM o n System Board BIO S 00FFFF F the Sys ...

  • Aiwa 586IVX - page 64

    64 Note : The I/O address hex 0000 to 00FF are reserved for the system boar d I/O. Hex 0100 to 03FF are available on the I/O channels . I/O Address Ma p I/O Addres s Functio n 0000-001 F DMA Controller 1, 8237A- 5 0020-003 F Interrupt Controller 1, 8259A, Maste r 0040-005 F Time r , 8254- 2 0060-006 F 8742 (Keyboard Controller ) 0070-007 F Real-tim ...

  • Aiwa 586IVX - page 65

    65 Appendix C Connector s Connector s J 2 J 4 J 8 J 9 J1 0 J1 1 J1 2 J1 3 CN 1 CN 5 CN 6 CN 7 USB 1 connecto r USB 2 connecto r IrDA connecto r Fan connecto r Floppy disk drive connecto r Primary IDE hard disk drive connecto r Secondary IDE hard disk drive connecto r ATX power LE D HD LE D Green LE D ATX power switc h Green switc h Reset switc h AT ...

  • Aiwa 586IVX - page 66

    66 CN 8 CN 9 PL 1 PS/2 mouse por t Game por t ATX power connecto r J8 J11 J12 J10 J9 PL1 J13 CN6 CN5 J4 CN1 CN8 J2 CN7 ...

  • Aiwa 586IVX - page 67

    67 Pi n 1 2 3 Functio n Groun d +12 V Groun d Pin Assignment s J8 - Infrared connecto r Pi n 1 2 3 4 5 Functio n IRT X GN D IRR X IRR 3 VC C J9 - Fan connecto r ...

  • Aiwa 586IVX - page 68

    68 J1 3 Pin 1 Pin 2 +5 V Groun d Pin 1 Pin 2 +5 V Signa l Pin 1 Pin 2 +5 V Signa l Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Signa l Groun d Pin 1 Pin 2 Pin 3 Pin 4 Signa l N.C . Groun d +5 V Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 +5 V N.C . Groun d Keylock Signa l Groun d HD-LE D (Primary/Secondar y IDE LED ) G-LE D (Green LED ) S ...

Fabbricante Aiwa Categoria Computer Hardware

I documenti che otteniamo dal fabbricante del dispositivoAiwa 586IVX possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Aiwa
- manuali per l’uso 586IVX
- schede prodotto Aiwa
- opuscoli
- o etichette energetiche Aiwa 586IVX
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Aiwa 586IVX.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Aiwa 586IVX, manuali di manutenzione, brevi manuali o manuali utente Aiwa 586IVX. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Aiwa 586IVX.

Manuali per l’uso simili

Manuale completo del dispositivo Aiwa 586IVX, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Aiwa 586IVX dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Aiwa 586IVX.

Il manuale per l’uso completo Aiwa, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Aiwa 586IVX - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Aiwa 586IVX, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Aiwa 586IVX che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Aiwa 586IVX - che ci dovrebbe aiutare nei primi passi durante l'uso Aiwa 586IVX
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Aiwa 586IVX
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Aiwa 586IVX in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Aiwa 586IVX?

Utilizza il modulo sottostante

Se non hai risolto il problema con Aiwa 586IVX con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Aiwa 586IVX è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)