Manuale per l’uso Broan ELITE E54000

44 pagine 3.04 mb
Scarica

Vai alla pagina of 44

Summary
  • Broan ELITE E54000 - page 1

    Model E54000 ENGLISH....................................2 FRANÇAIS...............................15 ESPAÑOL.................................28 99043938E In USA - BROAN Hartford, Wisconsin In CANADA - BROAN Drummondville, QC, Canada REGISTER YOUR PRODUCT ONLINE AT : www.Broan.com/register For additional Information visit www.Broan.com ...

  • Broan ELITE E54000 - page 2

    - 2 - READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1 . Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2 . Before servicing or cleaning unit, s ...

  • Broan ELITE E54000 - page 3

    - 3 - ! CAUTION 1 . For indoor use only. 2 . To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. 3 . Take care when using cleaning agents or detergents. 4 . Avoid using food products that produce flames under the Range ...

  • Broan ELITE E54000 - page 4

    - 4 - OPERATION Controls The hood is operated using the slide controls under the bottom of the hood. The light switch turns the lamps on and off. The blower switch turn the blower on to three speed settings: 0 - OFF 1 - LOW SPEED 2 - MEDIUM SPEED 3 - HIGH SPEED The pilot lamp lights up whenever the blower is on. HEAT SENTRY™ Your hood is equipped ...

  • Broan ELITE E54000 - page 5

    - 5 - FUSE REPLACEMENT IF LIGHTS FAIL TO OPERATE, DISCONNECT THE POWER AT THE SERVICE ENTRANCE. CHECK THE FUSE AND REPLACE IF NECESSARY. 1. Remove the grease filters. 2. Remove the cover of the fuse box. 3. Locate the fuse holder. Unscrew its cap and remove the fuse. 4. Replace the fuse with the same size and amperage (5x20mm, 4amp, 125volt). Do no ...

  • Broan ELITE E54000 - page 6

    - 6 - MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filter The grease filter should be cleaned frequently. Use a warm detergent solution. Grease filter is dishwasher safe. See “INSTALL FILTERS” section for removal and installation instructions. Non-ducted Recirculation Filter The non-ducted ...

  • Broan ELITE E54000 - page 7

    - 7 - PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Support Frame 1 - Parts Bag containing: 1 - Support Frame Bracket 1 - Discharge Collar 4 - Lag Bolts (6 x 70mm) 14 - Mounting Screws (3.9 x 9.5mm Pan Head) 2 - Mounting Screws (2.9 x 9.5mm Pan Head) 4 - Washers 6.4mm Diameter 6 - Ser ...

  • Broan ELITE E54000 - page 8

    - 8 - INSTALL THE DUCTWORK DUCTED HOODS ONLY ! CAUTION: To reduce the risk of fire, use only metal ductwork. 1 . Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run will allow the hood to perform most efficiently. 3. Long duct runs, elbows, and transitions will reduce the performance of the hood. Use a ...

  • Broan ELITE E54000 - page 9

    - 9 - PREPARE SUPPORT FRAME 8 AND 9-FOOT CEILINGS 1. Measure the ceiling height and determine distance between the cook top and bottom of hood. 2. Remove (4) screws and washers in the height adjustment slots. Figure 8. 3. Per the chart, adjust overall lenght of the support frame. Figure 8. 4. Reinstall (4) screws and washers in the height adjustmen ...

  • Broan ELITE E54000 - page 10

    - 10 - MOUNTING SCREWS (3.9x9.5mm) SUPPORT FRAME BRACKET FRONT SUPPORT FRAME FIG. 9 PREPARE SUPPORT FRAME, cont’d. 7. Hang the support frame from the support frame bracket (located on ceiling). Securely fasten with (4) 3.9x9.5mm mounting screws. Fig. 9. PREPARE THE HOOD DUCTED AND NON-DUCTED HOODS 1. Assemble the Electrical Mounting Plate to the ...

  • Broan ELITE E54000 - page 11

    - 11 - FIG.13 NON-DUCTED RECIRCULATION PLENUM FIG.14 DUCT CONNECTOR 5” METAL EXPANSION DUCT PREPARE THE HOOD, cont’d. NON-DUCTED HOODS ONLY 3. Install the non-ducted recirculation plenum through the upper rectangular openings in the support frame. Fig. 13 4. Install the 5” diameter duct connector to plenum. Twist and lock to secure. Fig. 14. ...

  • Broan ELITE E54000 - page 12

    - 12 - INSTALL THE UPPER DECORATIVE FLUE, cont’d. NON-DUCTED HOODS ONLY (8-FOOT AND 9-FOOT CEILINGS) 4. Install the upper flue with air vent “up”. Secure to the support frame with (2) 2.9x9.5mm mounting screws. Fig. 16. (10-FOOT CEILINGS) 5. Discard the upper flue supplied with the hood. Replace with the upper flue supplied with flue extensio ...

  • Broan ELITE E54000 - page 13

    - 13 - 5” NON-DUCTED CONNECTION TAPE FIG.19 CONNECT THE DUCTWORK Duct tape all connecton’s to make them secure and air tight. DUCTED HOODS ONLY 1. Connect 6” diameter metal duct to ducting that discharges to the outside. NON-DUCTED HOODS ONLY 2. Connect 5” diameter expandable metal duct from the non-ducted plenum to the adapter on the blowe ...

  • Broan ELITE E54000 - page 14

    - 14 - INSTALL FILTERS (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filter, push in on the metal latch tab and tilt filter downward to remove. 2. To install the GREASE filter, align rear filter tabs with slots in the hood. Depress the metal latch tab, push filter into posi- tion and release. Make sure filter is se- curely engaged after ins ...

  • Broan ELITE E54000 - page 15

    - 15 - LISEZ ET CONSERVEZ CES INSTRUCTIONS AVERTISSEMENT POUR RÉDUIRE LES RISQUES D’INCENDIE, D’ÉLECTROCUTION OU DE BLESSURES CORPORELLES, OBSERVEZ LES INSTRUCTIONS SUIVANTES : 1 . N’utilisez cet appareil que de la façon prévue par le manufacturier. Si vous avez des questions, contactez le manufacturier à l’adresse ou au numéro de té ...

  • Broan ELITE E54000 - page 16

    - 16 - 4 . Utilisez un extincteur SEULEMENT LORSQUE : A . Vous savez qu’il s’agit d’un extincteur de classe ABC et que vous en connaissez le fonctionnement. B . L’incendie est petit et limité à l’endroit où il a débuté. C . Les pompiers ont été avisés. D . Vous pouvez combattre l’incendie en ayant accès à une sortie de secours ...

  • Broan ELITE E54000 - page 17

    - 17 - FONCTIONNEMENT Commandes La hotte fonctionne à l’aide des boutons coulissants situés sous la partie inférieure de la hotte. L’ interrupteur d’éclairage allume et éteint les lampes. L’ interrupteur du ventilateur active le ventilateur à trois régimes différents : 0 - ARRÊT 1 - BASSE VITESSE 2 - MOYENNE VITESSE 3 - HAUTE VITES ...

  • Broan ELITE E54000 - page 18

    - 18 - REMPLACEMENT DU FUSIBLE SI LES LAMPES NE FONCTIONNENT PAS, DÉCONNECTER L’ALIMENTATION ÉLECTRIQUE AU POINT D’ORIGINE DE L’INSTALLATION ÉLECTRIQUE. VÉRIFIER QUE LE FUSIBLE SOIT EN BON ÉTAT, PUIS LE REMPLACER AU BESOIN. 1. Retirer les filtres à graisses. 2. Retirer le couvercle de la boîte du fusible. 3 . Localiser le porte-fusible ...

  • Broan ELITE E54000 - page 19

    - 19 - ENTRETIEN Un bon entretien de votre hotte garantira une excellente performance. Filtres à graisses Les filtres à graisses doivent être nettoyés fréquemment. Utiliser une solution d’eau chaude additionnée de détergent. Les filtres à graisses peuvent être lavés au lave- vaisselle. Voir la section « INSTALLATION DES FILTRES » pour ...

  • Broan ELITE E54000 - page 20

    - 20 - PRÉPARATION DE LA HOTTE Retirer la hotte de l’emballage, puis vérifier le contenu. Vous devez recevoir : 1 - Hotte 1 - Conduit décoratif 1 - Structure de support 1 - Sachet avec : 1 - Bride de la structure de support 1 - Collier d’évacuation 4 - Tire-fond (6 x 70 mm) 14 -Vis de montage (3,9 x 9,5 mm, tête ronde) 2 - Vis de montage ( ...

  • Broan ELITE E54000 - page 21

    - 21 - INSTALLATION DU SYSTÈME DE CONDUITS HOTTES À ÉVACUATION EXTÉRIEURE SEULEMENT ! ATTENTION : Pour réduire les risques d’incendie, n’utilisez que des conduits en métal. 1. Déterminer par où passera le conduit, entre votre hotte et l’extérieur. 2. Un conduit droit et court permettra à votre hotte de fonctionner plus efficacement. ...

  • Broan ELITE E54000 - page 22

    - 22 - PRÉPARATION DE LA STRUCTURE DE SUPPORT PLAFONDS DE 8 PI ET DE 9 PI 1. Mesurer la hauteur de plafond et établir la distance entre la surface de cuisson et le bas de la hotte. 2. Enlever les (4) vis et rondelles des fentes de réglage de hauteur. Figure 8. 3 . Régler la longueur générale de la structure de support selon le graphique. Figu ...

  • Broan ELITE E54000 - page 23

    - 23 - PRÉPARATION DE LA STRUCTURE DE SUPPORT (suite) 7. Suspendre la structure de support à la bride de la structure (au plafond). Bien serrer avec les (4) vis de montage de 3,9 mm x 9,5 mm. Fig. 9. PRÉPARATION DE LA HOTTE HOTTES À ÉVACUATION ET À RECIRCULATION 1 . Assembler la plaque d’installation électrique à la hotte en utilisant les ...

  • Broan ELITE E54000 - page 24

    - 24 - PRÉPARATION DE LA HOTTE (suite) HOTTES À RECIRCULATION SEULEMENT 3. Installer le déflecteur à travers les ouvertures rectangulaires dans la structure de support. Fig. 13 4. Monter le raccord de conduit d’un diamètre de 5 po sur le déflecteur. Tourner et verrouiller en place. Fig. 14. 5. Fixer le conduit métallique extensible de 5 po ...

  • Broan ELITE E54000 - page 25

    - 25 - CONDUIT DÉCORATIF INFÉRIEUR VIS DE MONTAGE (3,9 x 9,5 mm) MONTAGE DU CONDUIT D É C ORATIF SUPÉRIEUR (suite) HOTTES À RECIRCULATION SEULEMENT (PLAFONDS DE 8 PI ET DE 9 PI) 4. Installer le conduit décoratif supérieur avec la grille d’aération en haut. Fixer sur la structure de support avec les (2) vis de montage de 2,9 x 9,5 mm. Fig. ...

  • Broan ELITE E54000 - page 26

    - 26 - RACCORD DES CONDUITS Sceller hermétiquement tous les joints à l’aide de ruban à conduits. HOTTES À ÉVACUATION SEULEMENT 1. Raccorder le conduit métallique de 6 po de diamètre aux conduits d’évacuation vers l’air libre. HOTTES À RECIRCULATION SEULEMENT 2 . Raccorder le conduit métallique extensible de 5 po de diamètre allant ...

  • Broan ELITE E54000 - page 27

    - 27 - INSTALLATION DES FILTRES (HOTTES À ÉVACUATION ET À RECIRCULATION) 1. Pour retirer le filtre à GRAISSES, abaisser l a languette du taquet et incliner vers le bas. 2 . Pour replacer le filtre à GRAISSES, aligner les languettes arrière du filtre avec les fentes de la hotte. Abaisser la languette vers le bas, pousser le filtre pour le reme ...

  • Broan ELITE E54000 - page 28

    - 28 - LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA PARA EVITAR EL RIESGO DE INCENDIO, CORTOCIRCUITO O DAÑO PARA LAS PERSONAS, OBSERVE ATENTAMENTE LAS SIGUIENTES NORMAS: 1 . Use esta unidad solamente de la manera indicada por el fabricante; si tiene dudas, póngase en contacto con éste a la dirección o teléfono indicados en la garantía. 2 . ...

  • Broan ELITE E54000 - page 29

    - 29 - ! ADVERTENCIA 1 . Para uso en interiores. 2. Para reducir el riesgo de incendios y para evacuar correctamente los humos, asegurarse de haber realizado una conducción del aire hasta el exterior. No expulsar los humos en espacios cerrados por paredes o techos, áticos, espacios angostos o garajes. 3 . Prestar la máxima atención al utilizar ...

  • Broan ELITE E54000 - page 30

    - 30 - FUNCIONAMIENTO Mandos La campana se controla mediante los mandos corrrederos situados en la parte inferior de la misma. El interruptor da luz enciende y apaga las lámparas. El interruptor del aspirador enciende el ventilator en uno de los siguientes ajustes de velocidad: 0 - APAGADO 1 - VELOCIDAD BAJA 2 - VELOCIDAD MEDIA 3 - VELOCIDAD ALTA ...

  • Broan ELITE E54000 - page 31

    - 31 - SUSTITUCIÓN DEL FUSIBLE SI LAS LUCES NO FUNCIONAN, DESCONECTE LA ELECTRICIDAD EN LA ENTRADA DE SERVICIO. COMPRUEBE EL FUSIBLE Y, SI FUESE NECESARIO, SUSITITÚYALO. 1. Retire los filtros antigrasa. 2. Retire la cubierta de la caja fusible. 3. Localice el soporte del fusible. Desatornille su tapa y retire el fusible. 4. Sustituya el fusible p ...

  • Broan ELITE E54000 - page 32

    - 32 - MANTENIMIENTO Un mantenimiento adecuado de la campana asegura el funcionamiento correcto del aparato. Filtro antigrasa El filtro antigrasa debe limpiarse con frecuencia. Use un detergente que no sea fuerte. Use un detergente que no sea fuerte. El filtro antigrasa se puede meter en el lavavajillas. Las instrucciones de desmontaje e instalaci? ...

  • Broan ELITE E54000 - page 33

    - 33 - PREPARE LA CAMPANA Sacar la campana de l’embalaje y controlar el contenido. Recivireis: 1 - Campana 1 - Chimenea decorativa 1 - Armazón de soporte 1 - Bolsita con: 1 - Placa armazón de soporte 1 - Casquillo 4 - Tirafonds (6 x 70mm) 14 - Tornillos de montaje (3.9 x 9.5mm cabeza redonda) 2 - Tornillos de montaje (2.9 x 9.5mm cabeza redonda ...

  • Broan ELITE E54000 - page 34

    - 34 - INSTALACION DEL TUBO DE EXTRACCION CAMPANAS CON CONDUCTO ! NOTA: para evitar el riesgo de incendio, use solamente material de metal. 1. Decida donde va a colocar el tubo de extracción entre la campana y la parte exterior. 2 . Un recorrido de tubo corto y recto permitirá a la campana funcionar de manera más eficaz. 3. Los recorridos largos ...

  • Broan ELITE E54000 - page 35

    - 35 - PREPARACIÓN DEL ARMAZÓN DE SOPORTE TECHOS DE 8 O 9 PIES 1. Mida la altura del techo y determine la distancia entre la encimera y la parte inferior de la campana. 2. Retire los cuatro tornillos y arandelas de las ranuras de ajuste de la altura. Figura 8. 3. Ajuste la longitud total del armazón de soporte de acuerdo con la tabla. Figura 8. ...

  • Broan ELITE E54000 - page 36

    - 36 - PREPARACIÓN DEL ARMAZÓN DE SOPORTE, cont. 7. Cuelgue el armazón de soporte de la brida para armazón de soporte (situada en el techo). Fije firmemente con cuatro tornillos de montaje de 3,9 x 9,5 mm. Fig. 9. PREPARACIÓN DE LA CAMPANA CAMPANAS CON O SIN CONDUCTO 1. Monte la Placa del sistema eléctrico a la campana con dos tornillos de mo ...

  • Broan ELITE E54000 - page 37

    - 37 - PLENO PREPARACIÓN DE LA CAMPANA, cont. SÓLO PARA CAMPANAS SIN CONDUCTO 3. Monte el pleno a través de la abertura rectangular superior del armazón de soporte. Fig. 13 4. Monte el conector de conductos de 5" de diámetro al pleno. Gire y bloquee para fijar. Fig. 14. 5. Fije el conducto expansible metálico de 5" de diámetro al p ...

  • Broan ELITE E54000 - page 38

    - 38 - CHIMENEA INFERIOR TORNILLOS DE MONTAJE (3.9x9.5mm) MONTAJE DE LA CHIMENEA DECORATIVA SUPERIOR, Cont. SÓLO PARA CAMPANAS SIN CONDUCTO (TECHOS DE 8 O 9 PIES) 4 . Monte la chimenea superior con los respiraderos arriba. Fíjela al armazón de soporte con dos tornillos de montaje de 3.9 x 9.5 mm. Fig. 16. (TECHOS DE 10 PIES) 5 . Deseche la chime ...

  • Broan ELITE E54000 - page 39

    - 39 - CONEXIÓN DE LA TUBERÍA Encinte todas las conexiones para fijarlas y estanqueizarlas. SÓLO PARA CAMPANAS CON CONDUCTO 1. Conecte el conducto metálico de 6" de diámetro a la tubería que descarga al exterior. SÓLO PARA CAMPANAS SIN CONDUCTO 2 . Conecte el conducto metálico expansible de 5" entre el pleno y el adaptador de la d ...

  • Broan ELITE E54000 - page 40

    - 40 - INSTALACIÓN DE FILTROS (CONFIGURACIÓN CON CONDUCTO Y SIN CONDUCTO) 1. Para quitar el filtro de GRASA, agarre con fuerza la lengüeta del seguro y tire de ella. 2. Para instalar el filtro de GRASA, alinee las lengüetas posteriores del filtro con las ranuras de la campana. Tire de la lengüeta del seguro hacia abajo, coloque el filtro en su ...

  • Broan ELITE E54000 - page 41

    - 41 - SERVICE PARTS MODEL E54000 KEY NO. PART NO. DESCRIPTION 9 B08087294 Grease Filter 14 B02300233 Motor Capacitor 16 BE3348527 Electrical Mounting Plate 19 B03295005 T r an s former Protection 26 B02300891 Halogen Lamp Bulb 37 B02300804 Heat Sentry 39 B03294033 Control Board Box Cover 45 BW0000019 Blower 48 B02310260 Motor 49 B03295 071 Blower ...

  • Broan ELITE E54000 - page 42

    - 42 - LISTE DES PIÈCES DE RECHANGE MODELE E54000 N O N O DE PIÈCE DESCRIPTION 9 B08087294 Filtre à graisses 14 B02300233 Condensateur du moteur 16 BE3348527 Plaque d’installation électrique 19 B03295005 Protection du transformateur 2 6 B02300891 Ampoule halogène 37 B02300804 Capteur thermique HEAT SENTRY MC 39 B03294033 Couvercle de boîte ...

  • Broan ELITE E54000 - page 43

    - 43 - LISTA DE PIEZAS DE RECAMBIO MODELO E54000 CÓD. N. PIEZA N. DESCRIPCIÓN 9 B08087294 Filtro antigrasa 14 B02300233 Condensador 16 BE3348527 Placa del sistema electrico 19 B03295005 Protección trasformador 26 B02300891 Lámpara halógena 37 B02300804 Sensor de temperatura 39 B03294033 Tapa de la caja base de instalación eléctrica 45 BW0000 ...

  • Broan ELITE E54000 - page 44

    SERVICE PARTS - LISTE DES PIÈCES DE RECHANGE - LISTA DE PIEZAS DE RECAMBIO MODEL E54000 04307632/7 ...

Fabbricante Broan Categoria Flat Panel Television

I documenti che otteniamo dal fabbricante del dispositivoBroan ELITE E54000 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Broan
- manuali per l’uso ELITE E54000
- schede prodotto Broan
- opuscoli
- o etichette energetiche Broan ELITE E54000
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Broan ELITE E54000.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Broan ELITE E54000, manuali di manutenzione, brevi manuali o manuali utente Broan ELITE E54000. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Broan ELITE E54000.

Manuali per l’uso simili

Manuale completo del dispositivo Broan ELITE E54000, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Broan ELITE E54000 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Broan ELITE E54000.

Il manuale per l’uso completo Broan, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Broan ELITE E54000 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Broan ELITE E54000, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Broan ELITE E54000 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Broan ELITE E54000 - che ci dovrebbe aiutare nei primi passi durante l'uso Broan ELITE E54000
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Broan ELITE E54000
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Broan ELITE E54000 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Broan ELITE E54000?

Utilizza il modulo sottostante

Se non hai risolto il problema con Broan ELITE E54000 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Broan ELITE E54000 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)