Italiano dropdown-ico

Manuale per l’uso Chamberlain 1140

32 pagine 2.49 mb
Scarica

Vai alla pagina of 32

Summary
  • Chamberlain 1140 - page 1

    QLD Office: 17 Oasis Court Clontarf 4019 (07) 3883-0200 NSW Office: 34-36 Marigold Street Revesby 2212 (02) 9722 5555 VIC/T AS Office: 147-153 Canterbury Road Kilsyth 3137 (03) 9237 7766 B&D Doors New Zealand: 70 Allens Road EastT amaki Auckland, New Zealand (09) 273 8600 www .bnd.co.nz SA Office: 23 Frederick Road Royal Park 5014 (08) 8447 474 ...

  • Chamberlain 1140 - page 2

    2 Introduction 2-7 Safety rule review ........................................................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning ..................................................................4-5 Carton inventory .......... ...

  • Chamberlain 1140 - page 3

    3 Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench Locking pliers 13mm, 11mm, and 6mm Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 8mm, 5mm, and 4mm Drill Bits Carpenter's Level T o avoid damage to the garage door and opener , disable locks before installing and operating the opener . Use a woo ...

  • Chamberlain 1140 - page 4

    Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fibreglass, steel, aluminum, door with glass panels, etc.). See page 21 for details. Support bracket & fastening hardware is required. See page 17. — — — — — — — — Door Centre Header W all Safety Reversing Sensor Gap between flo ...

  • Chamberlain 1140 - page 5

    5 Access Door Gap between floor and bottom of door must not exceed 6mm. Safety Reversing Sensor The Chamberlain Group, Inc. One-Piece Door with T rack Installation (Cable -USA) 3/3/93 Header Bracket Header Sleeve Bracket Door Bracket Straight Door Arm Curved Door Arm Tr o lley Emergency Release Rope & Handle Rail Garage Door Header Wa l l Safet ...

  • Chamberlain 1140 - page 6

    6 Y our garage door opener is packaged in two cartons which contains the motor unit and the parts illustrated below . If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and packing material until installation and adjustment i ...

  • Chamberlain 1140 - page 7

    Hardwar e Inventory Separate all hardware and group as shown below for the assembly and installation procedures. 7 Spri ng /Tro lley Nut (1 ) Mast er Link (2) ASSE MBLY INSTALLATION NOT ICE Handle Rope Lock Was her 8mm (7) Hex Screw 8mm x 2 0mm (4) Nut 8mm (7) Carriage Bolt 8mm x 6 5mm (2) Screw (2 ) Was hered Screw 25 mm (4 ) (mo unted in op ener) ...

  • Chamberlain 1140 - page 8

    8 ASSEMBL Y STEP 1 Assemble the Rail NOTE: If your opener came with a one piece rail, proceed to Assembly step 2, page 9. Grease inside edges of rail brace sections. Place rail pieces on flat surface for assembly . All four rail sections are interchangeable. Slide rail braces onto rail section. Connect rail by sliding rail brace onto next rail sect ...

  • Chamberlain 1140 - page 9

    9 ASSEMBL Y STEP 3 Attach Chain Spreader Attach chain spreader to opener with phillips pan head screws. Chain Spreader P hillips Pan Head Screws Opener T o avoid serious damage to opener , ONL Y use screws mounted in top of motor unit. W W ARN ARN ING ING CAUTION CAUTION ATTENTION ATTENTION AVERTISSEMENT AVERTISSEMENT ASSEMBL Y STEP 2 Attach T roll ...

  • Chamberlain 1140 - page 10

    Bolt Tr olley Stop Bolt Hole L ock Was her Nut Bolt Nut Lock Washer Was h ere d Bolt Spr o ck e t 2 S top s 4 Spr o ck e t Spre a d er Stops Spreader Screwdriver T ip Nut Ring Wre nch Spring Nut Header Sleeve Screwdriver T ip Nut Ring Wre nch Spring Nut Header Sleeve F ASTEN RAIL TO OPENER SET CHAIN TENSION 10 1 14A2845 114mm 114mm 1. Clean and rem ...

  • Chamberlain 1140 - page 11

    11 IMPORT ANT INST ALLA TION INSTRUCTIONS 1. READ AND FOLLOW ALL INST ALLA TION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener only on properly balanced and lubricated garage door . An improperly balanced door may not reverse when required and could result in severe injury or death. 3. All repairs to cables, spring assemblies and other ha ...

  • Chamberlain 1140 - page 12

    12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centreline of the garage door . 2. Extend the line onto the header wall above the d ...

  • Chamberlain 1140 - page 13

    13 One Piece Door Without T rack 1/30/92 - 4/7/92 Header Wa l l Ve r tical Centreline Ve r tical Centreline of Garage Door 40mm Reinforcement Board Unfinished Ceiling OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports 40mm Reinforcement Board ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centreline of your g ...

  • Chamberlain 1140 - page 14

    14 INST ALLA TION STEP 2 Install the Header Bracket W ALL HEADER BRACKET INST ALLA TION • Centre the bracket on the vertical guideline with the bottom edge of the bracket on the horizontal line (with the arrow pointing toward the ceiling). • Mark all of the bracket holes. Drill 4.5mm (3/16") pilot holes and fasten the bracket with wood scr ...

  • Chamberlain 1140 - page 15

    15 Ring fastener (2) Temporary Support Garage Door Header Wall Header Bracket Header Sleeve Bracket Clevis PIn 8mm x 13mm (2) Ring Fastener Ring Fastener Clevis Pin 8mm x 13mm Clevis Pin 8mm x 13mm Header Sleeve Bracket Rai l HARDW ARE SHOWN ACTUAL SIZE INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position opener on garage floor ...

  • Chamberlain 1140 - page 16

    16 T op of Motor Unit Header Bracket Top of door Door ONE-PIECE DOOR WITHOUT TRACK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height. • The top of the door should be level with the top of the motor un ...

  • Chamberlain 1140 - page 17

    17 1 14A2845 INST ALLA TION STEP 6 Install the door control Locate the door control within sight of the door at a minimum height of 1.5m where small children cannot reach, and away from all moving parts of the door and door hardware. 1. Strip 6mm of insulation from one end of the bell wire. Connect it to the two screw terminals on the back of the d ...

  • Chamberlain 1140 - page 18

    18 WIRING INSTRUCTIONS FOR ACCESSORIES • Place entrapment warning label on the inside of door as a reminder of safe operating procedures. Place the manual release/safety reverse test label in plain view on the inside of the garage door . T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE in ...

  • Chamberlain 1140 - page 19

    19 1 14A2845 Overhand Knot Em ergency R elease Handle T rolley Release Arm NOTICE The Chamberlain Group, Inc. Figure 16 - Manual Release 4210E - 3/8/93 Rope T rolley • T o prevent possible SERIOUS INJURY or DEA TH from a falling garage door: – If possible, use emergency release handle to disengage trolley ONL Y when garage door is CLOSED. Weak ...

  • Chamberlain 1140 - page 20

    20 Invisible Light Beam Protection Area The Chamberlain Group, Inc. Safety Sensor Instruction Sheet Page 1  Protector System Disk #1 (Yellow) 11/5/91 - 1/15/92 Wing Nut Sensor Beam 100-150mm max. above floor Sensor Beam 100-150mm max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install the Sa ...

  • Chamberlain 1140 - page 21

    21 Carriage Bolt 8mm x 65mm Nut 8mm Lock Washer 8mm Sheet Metal Screw HARDW ARE SHOWN ACTUAL SIZE 1 14A2845 Fibreglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. T o prevent damage to garage doors reinforce inside of door with angle iron both vertically and horizontally . W W ARN ARN ...

  • Chamberlain 1140 - page 22

    22 Carriage Bolt 8mm x 65mm Nut 8mm Lock Washer 8mm Sheet Metal Screw HARDW ARE SHOWN ACTUAL SIZE 1 14A2845 Header W all Ve r tical Centreline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/ ...

  • Chamberlain 1140 - page 23

    23 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...

  • Chamberlain 1140 - page 24

    ALL ONE-PIECE DOORS Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 8mm x 32mm clevis pin. • Secure with a ring fastener . Adjustment Procedures for One-Piec ...

  • Chamberlain 1140 - page 25

    25 ADJUSTMENT STEP 1 Limit Adjustment Run the opener through a complete travel cycle. Force adjustments are not necessary when the door opens and closes completely and doesn't reverse unintentionally in the fully closed position. Locate the button on the back panel of motor unit. NOTE: if the operator stops or reverses and will not allow the r ...

  • Chamberlain 1140 - page 26

    ADJUSTMENT STEP 2 Adjust the Force The force, as measured on the closing edge of the door , should not exceed 400N (40kg). If the closing force is measured to more than 400N, a Safety Infrared Reversing Sensor must be installed See step 3 on page 27. The force setting button is located on the back panel of the motor unit. The force setting regulate ...

  • Chamberlain 1140 - page 27

    ADJUSTMENT STEP 3 T est the Safety Reverse System TEST • With the door fully open, place a 40mm board on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. ADJUST • If the door stops on the obstruction, it is not traveling far enough in the down direction. ...

  • Chamberlain 1140 - page 28

    28 Using Y our Garage Door Opener Y our opener will operate with up to twelve remote control transmitters, one entry keypad, and one dip- switch code transmitter . If you purchase a new remote, or if you wish to deactivate any remote, follow the instructions in the Programming section. Activate your opener with any of the following: • The hand-he ...

  • Chamberlain 1140 - page 29

    29 T o Open the Door Manually DISCONNECT THE TROLLEY : The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually . The lockout feature prevents the trolley from reconnecting automatically , and the door can be raised and lowered ...

  • Chamberlain 1140 - page 30

    T roubleshooting 1. Opener doesn't operate from either door control or remote: • Does the opener have electric power? Plug lamp into outlet. If it doesn't light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.) • Have you disengaged all door locks? Review installation instruction warnings on ...

  • Chamberlain 1140 - page 31

    31 T o Erase All Codes From Opener Receiver Memory T o deactivate any unwanted remote, first erase all codes: Press and hold the “Learn” button on opener until the smart indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use. Below are instructions for progra ...

  • Chamberlain 1140 - page 32

    1 14A2845 ©2005, All Rights Reserved Printed in Mexico W ARRANTY Controll-A-Door ® Automatic Garage Door Opener 1. Definitions ‘B&D’ means (a) in Australia - B&D Doors of 17 Oasis Court Clontarf, Queensland 4019 (b) in New Zealand - B&D Doors (NZ) Ltd of 70 Allens Road East T amaki Auckland, which is a subsidiary of Alesco NZ Ltd. ...

Fabbricante Chamberlain Categoria Garage Door Opener

I documenti che otteniamo dal fabbricante del dispositivoChamberlain 1140 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Chamberlain
- manuali per l’uso 1140
- schede prodotto Chamberlain
- opuscoli
- o etichette energetiche Chamberlain 1140
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Chamberlain 1140.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Chamberlain 1140, manuali di manutenzione, brevi manuali o manuali utente Chamberlain 1140. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Chamberlain 1140.

Manuali per l’uso simili

Manuale completo del dispositivo Chamberlain 1140, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Chamberlain 1140 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Chamberlain 1140.

Il manuale per l’uso completo Chamberlain, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Chamberlain 1140 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Chamberlain 1140, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Chamberlain 1140 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Chamberlain 1140 - che ci dovrebbe aiutare nei primi passi durante l'uso Chamberlain 1140
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Chamberlain 1140
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Chamberlain 1140 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Chamberlain 1140?

Utilizza il modulo sottostante

Se non hai risolto il problema con Chamberlain 1140 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Chamberlain 1140 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)