-
Cisco AIR-CAP702I-I-K9 - page 1
G ETTING S TARTED G UIDE Cisco Aironet 700 Series Access Points First Published: June 2013 Last Updated: September 2014 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Connectors 7 Configuring the Access Point 8 Mounting the Access Point 9 Deploying the Access Point ...
-
Cisco AIR-CAP702I-I-K9 - page 2
2 1 About this Guide This Guide provides in structions on how to install and conf igure your Cisco Aironet 700 Seri es Access Point. The 700 Series Access Point is referred to as the 700 series or the access point in this document. 2 Introduction to the Access Point The 700 series supports high-performing two spatial stream rates over a deployab le ...
-
Cisco AIR-CAP702I-I-K9 - page 3
3 War n in g IMPORT ANT SAFETY INSTRUCTIONS This warning symbol means d anger . Y ou are in a situation that could cause bod ily injury . Before you work on any equipment, be aware of the hazards invo lved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of ea c ...
-
Cisco AIR-CAP702I-I-K9 - page 4
4 4 Unpacking T o unpack the access point , follow these steps: Step 1 Unpa ck and remove the access point and the accessory kit from the shipping box . Step 2 Re turn any packing material to the shippi ng con tainer and save it for future use. Step 3 V erify that you have received the items lis ted below . If any item is missing or da maged, conta ...
-
Cisco AIR-CAP702I-I-K9 - page 5
5 Figur e 1 Access P oint LED Indicator (t op) The ports and connections on the side of the access point are shown in Figure 2 . 1 LED indicator 347756 1 ...
-
Cisco AIR-CAP702I-I-K9 - page 6
6 Figur e 2 Access P oint P orts and Connection s (bot tom) 7 Configuring the Access Point This section describes how to connect the access point to a wir eless LAN controller . Because th e configura tion process takes place on the co ntroller , see the Cisco Wireless LAN Controller Configuration Guide for additional information. This guide is ava ...
-
Cisco AIR-CAP702I-I-K9 - page 7
7 The Controller Discovery Process The access point uses standard Control and Provisioning of Wireless Access Points Protocol (CAPW AP ) to communicate between the controller and other wireless access points on the network. CAPW AP is a standard, interoperable pro tocol which enables an access controller to ma nage a collection of wirele ss termina ...
-
Cisco AIR-CAP702I-I-K9 - page 8
8 Preparing the Access Point Before you mount and deploy your access poin t, we recommend that you perform a site su rvey (or use the site planning tool) to determine the best location to install your access point. Y ou should have the following in formation about your wireless network available: • Access point locations. • Access point mountin ...
-
Cisco AIR-CAP702I-I-K9 - page 9
9 Figure 3 Pr e-Installat ion Configuration Setup T o perform pre-installati on configuration, perform the following steps: Step 1 Mak e sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco Prime Infras tructure procedures as de scri bed in the appropriate Cisc o wireless LA N ...
-
Cisco AIR-CAP702I-I-K9 - page 10
10 e. If the operating system download is successful, the access point reboots. Step 3 Config ure the access point if required. Use the controller CLI, contro ller GUI, or Cisco P rime Infrastructure to customize the access-point-spe cific 802.11n network settings. Step 4 If the pre-installatio n configuration is successful, the Status LED is green ...
-
Cisco AIR-CAP702I-I-K9 - page 11
11 10 Troubleshooting If you experience difficulty getting your access point installe d a nd running, look for a solution to your problem in this guide or in additional access point documentation. These, an d other documents, are available on Cisco.com. Guidelines for Using Cisco Ai ronet Lightweigh t Access Points Keep these guidelines in mind whe ...
-
Cisco AIR-CAP702I-I-K9 - page 12
12 Troubleshooting the Ac cess Point Join Process Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signe d certificates are n ot enabled on the controller; the access point’ s a nd controller’ s regu latory domains don’t match, and so on. Controller software enables you to configure th e ac ...
-
Cisco AIR-CAP702I-I-K9 - page 13
13 An access point sends all syslo g messages to IP address 255.255.255.255 b y default when any of the following conditions are met: • An access point running software release 5.2 or later has been newly deploy ed. • An existing access point running softw are release 5.2 or later has been re set after clearing the configuration. If any of thes ...
-
Cisco AIR-CAP702I-I-K9 - page 14
14 Manufacturer: Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the followin g two conditions: 1. This device ma y not cause harmful interference, a nd 2. This device must accept any interference received, incl uding interference that may ca use undesired oper ...
-
Cisco AIR-CAP702I-I-K9 - page 15
15 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet a ccess po ints in Ja pan. These guideline s are provided in both Japanese and English. Japanese Translation English Translation This equipment operates in the same freque ncy bandwidth as industri ...
-
Cisco AIR-CAP702I-I-K9 - page 16
16 English Translation When installing the product, please use the provid ed or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Elect rical Appliance an d Material Safety Law proh ibits the use of UL-certified cables (that have the “UL” sh own on the code) for any other ...
-
Cisco AIR-CAP702I-I-K9 - page 17
17 European Community, Switzerland, Norway, Iceland, and Liechtenstein Models: AIR-CAP702I-E-K9 AIR-SAP702I-E-K9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC ...
-
Cisco AIR-CAP702I-I-K9 - page 18
18 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referr ed to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed. This device also conforms to the EMC re ...
-
Cisco AIR-CAP702I-I-K9 - page 19
19 Generic Discussion on RF Exposure The Cisco products are designed to comply with the following na tional and international standard s on Human Exposure to Radio F requencies: • US 47 Code of Federal Regulations Pa rt 2 Subpart J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (9 ...
-
Cisco AIR-CAP702I-I-K9 - page 20
20 This Device Meets the In dustry Canada Guidelines fo r Exposure to Radio Waves The 700 series device includes a radio transmi tter and receiver . It is desi gned not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as refer e nced in Health Canada Safety Code 6. The guidelines include a substantial safety ...
-
Cisco AIR-CAP702I-I-K9 - page 21
21 • FCC Bulletin 65C (01-01): Evaluating Comp liance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields: Additiona l Information for Evaluati ng Compliance for Mobi le and Portable Devices with FCC limits for Human Exposure to Radio Frequency Emission Y ou can obtain additional information from the following org ...
-
Cisco AIR-CAP702I-I-K9 - page 22
22 The operation of the low-power ra dio-freque ncy devices is subjec t to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediatel y and can't re-operate it until th e harmful interference is clear . The authorized r ...
-
Cisco AIR-CAP702I-I-K9 - page 23
23 Operation of Cisco Aironet Access Points in Brazil This section contains special information for ope ration o f Cisco Aironet access points in Bra zil. Access Point Models AIR-CAP702I-T -K9 AIR-SAP702I-T -K9 Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a prot eção con tra interferência preju ...
-
Cisco AIR-CAP702I-I-K9 - page 24
24 Step 2 Crea te the DHCP pool, including the ne cessary parameters such as default r outer and name server . A DHCP scope example is as follows: ip dhcp pool <pool name> network <IP Network> <Netmask> default-router <Default router> dns-server <DNS Server> Where: <pool name> is the name of the DHCP pool, such a ...
-
Cisco AIR-CAP702I-I-K9 - page 25
25 ...
-
Cisco AIR-CAP702I-I-K9 - page 26
26 Cisco and the Cisco logo are trademarks or registered tra demarks of Cisco and/or its affiliates in the U.S. and other countries. T o view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their re spective owners. The use of the word partner does not imply a pa rtnersh ...
Hai una domanda su Cisco AIR-CAP702I-I-K9?
Utilizza il modulo sottostante
Se non hai risolto il problema con Cisco AIR-CAP702I-I-K9 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco AIR-CAP702I-I-K9 è probabile che voglia condividere il modo di risolverlo.