-
Porter-Cable 100H - page 1
Router Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No. _______________________________________ IMPORT ANT Please make ...
-
Porter-Cable 100H - page 2
2 SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks and cement and other masonry pr oducts, and · arsenic and ...
-
Porter-Cable 100H - page 3
3 ELECTRICAL SAFETY 1. Grounded tools must be plugged into an outlet pr operly installed and grounded in accor dance with all codes and ordinances. Never r emove the grounding pr ong or modify the plug in any way . Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly gr ounded. If ...
-
Porter-Cable 100H - page 4
4 2. Do not force tool. Use the corr ect tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use tool if switch does not turn it ON or OFF . A tool that cannot be controlled with the switch is danger ous and must be repair ed. 4. Disconnect the plug from the power sour ce befo ...
-
Porter-Cable 100H - page 5
5 10. A VOID “CLIMB-CUTTING”. (See section “USING THE TOOL” in this manual). “Climb-cutting” increases the cha nce for loss of contr ol resulting in possible personal injury . 11. DO NOT HAND-HOLD THE ROUTER IN AN UPSIDE-DOWN OR HORIZONT AL POSITION. The motor can separate from the base if not properly attached accor ding to the instruc ...
-
Porter-Cable 100H - page 6
6 REPLACEMENT P ARTS When servicing use only identical replacement parts. MOTOR Many Porter -Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 per cent of that shown on the specification plate on the tool. Several models, however , are designed for A.C. current only . Refer to th ...
-
Porter-Cable 100H - page 7
7 SELECTING THE BIT This Router comes with a 1 / 4 " split type collet which accommodates bits with 1 / 4 " shanks. Disconnect tool from power sour ce while preparing it for use, making adjustments, and when it is not in use. INST ALLING AND REMOVING THE BIT DISCONNECT TOOL FROM POWER SOURCE. 1. T o remove motor unit from base unit: (a) O ...
-
Porter-Cable 100H - page 8
8 A TT ACHING THE MOTOR TO THE ROUTER BASE DISCONNECT TOOL FROM POWER SOURCE. 1. Open the clamp (A) Fig. 1 and set the power unit in the base unit. 2. Align the lower pin of the power unit (B) Fig. 1 with the groove in the base. 3. Rotate the power unit CLOCKWISE into the base until the upper guide pins are set in the gr oove of the base. 4. Close ...
-
Porter-Cable 100H - page 9
ST ARTING AND STOPPING THE MOTOR Before starting the r outer , make sure that the bit is clear of the workpiece and foreign objects. Keep a firm grip on router to r esist starting torque. Start and stop the motor by setting the toggle switch (A) Fig. 4 to the “ON” or “OFF” position. T o avoid personal injury or damage to finished work, alwa ...
-
Porter-Cable 100H - page 10
10 The speed and depth of cut will depend lar gely on the type of workpiece. Keep the cutting pressur e constant, but do not crowd the r outer so the motor speed slows excessively . More than one pass may be necessary on exceptionally hard woods or pr oblem materials to get the desired depth of cut. When making cuts on all four edges of the workpie ...
-
Porter-Cable 100H - page 11
11 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . Remove buildup of grime resulting fr om working with green or sappy wood. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear safety glasses while ...
-
Porter-Cable 100H - page 12
12 A complete line of accessories is available from your Porter - Cable • Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Porter -Cable Authorized Service Stations. Please visit our W eb Site www .porter -cable.com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Porter ...
-
Porter-Cable 100H - page 13
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T A ...
Porter-Cable 100Hについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもPorter-Cable 100Hの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 100Hで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。