Bushnell LS1440の取扱説明書

20ページ 0.22 mb
ダウンロード

ページに移動 of 20

Summary
  • Bushnell LS1440 - page 1

    INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. ENGLISH Miter Sa w MODEL LS1440 002146 DOUBLE INSULA TION ...

  • Bushnell LS1440 - page 2

    2 SPECIFICATIONS Blade diameter ................................................................................................................. ................................... 355 mm Hole diameter.................................................................................................................. ................ 25 mm and 25.4 m ...

  • Bushnell LS1440 - page 3

    3 GENERAL SAFETY RULES GEA001-3 W ARNING: Read all instructions. F ailure to f ollow all instructions listed below ma y result in electric shock, fire and/or serious injur y . The term “power tool” in all of the warnings listed below ref ers to your mains-operated (corded) po wer tool or batter y- operated (cordless) pow er tool. SA VE THESE IN ...

  • Bushnell LS1440 - page 4

    4 or storing power tools. Such pre ventive saf ety measures reduce the risk of star ting the power tool accidentally . 19. Store idle power tools out of the reach of c hil- dren and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. P ower tools are dangerous in the hands of untrained users. 20. Mai ...

  • Bushnell LS1440 - page 5

    5 27. Select saw blades in relation to the material to be cut. 28. T ake care when slotting. 29. Replace the kerf board when w orn. 30. Do not use saw blades manufactured from high speed steel. 31. Some dust created fr om operation contains chemicals known to cause cancer , birth defects or other reproductive harm. Some examples of these chemicals ...

  • Bushnell LS1440 - page 6

    6 INST ALLA TION Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the handle latch. Release the handle latch by low er ing the handle slightly and turn the handle latch to the released position. This tool should be bolted with four bolts to a le vel and stab le surface using the bolt holes provided in the to ...

  • Bushnell LS1440 - page 7

    7 Kerf boar d This tool is provided with the k erf board in the tur n base to minimize tearing on the exit side of a cut. If the k erf groov e has not yet been cut in the kerf board by the factory , you should cut the groov e before actually using the tool to cut a workpiece. Switch on the tool and low er the blade gently to cut a groov e in the ke ...

  • Bushnell LS1440 - page 8

    8 Fence plate The fence plate is designed to pre vent smaller cutting scraps from jamming inside the blade case. The f ence plate mov es r ight or left automatically as the turn base is rotated. Switch action CA UTION: • Before plugging in the tool, alw ays check to see that the s witch trigger actuates properly and returns to the “ OFF ” pos ...

  • Bushnell LS1440 - page 9

    9 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the hex bolt countercloc kwise. Then remov e the hex bolt, outer flange and blad e. T o install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surf ace of the blade matches the direction of the arrow on the b lade case ...

  • Bushnell LS1440 - page 10

    10 Slip the pin on the blade guard into the slot in the guide arm while returning the blade guard to its original fully closed position. Then tighten the he x bolt clock- wise to secure the center cov er. Lo wer the handle to make sure that the blade guard mov es proper ly . Make sure shaft loc k has released spindle before mak- ing cut. Dust bag T ...

  • Bushnell LS1440 - page 11

    11 Horizontal vise (Accessory) The horizontal vise can be installed on either the left or right side of the base. When performing 15 ° or greater miter cuts, install the horizontal vise on the side opposite the direction in which the turn base is to be tur ned. By turning the vise knob counterclockwise , the screw is released and the vise shaft ca ...

  • Bushnell LS1440 - page 12

    12 leav e a mar k (sa w mar k) in the wo r kpiece and the precision of the cut will be impaired. 1. Press cutting Secure the workpiece with the vise. Switch on the tool without the blade making any contact and wait until the b lade attains full speed before low- ering. Then gently lower the handle to the fully low ered position to cut the workpiece ...

  • Bushnell LS1440 - page 13

    13 After changing the miter angle, cut the wood f acing at that selected angle. If there is a gap between the b lade, the wood facing and the work- piece, mov e the wood facing slightly in the direct ion of the arrow and cut it again. CA UTION: • Use straight wood of e ven thickness as the w ood facing. • Use screws to attach the w ood facing t ...

  • Bushnell LS1440 - page 14

    14 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. WA R N I N G : • Alwa ys be sure that the blade is sharp and clean for the best and safest performance. Adjusting the cutting angle This tool is carefully adjusted and aligned at the factory , but rough ...

  • Bushnell LS1440 - page 15

    15 Adjusting for smooth handle action The hex loc k nut which holds the gear housing and the arm has been factory adjusted to assure smooth handle action up and down and to guarantee pre- cise cutting. Do not tamper with it. Should looseness dev elop at the gear hous- ing and arm connection, perform the following adjustment. W ork the handle up and ...

  • Bushnell LS1440 - page 16

    16 A CCESSORIES CA UTION: • These accessories or attachments are recommended for use with y our Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment for its stated purpose. If you need an y assistance for more details regarding these acce ...

  • Bushnell LS1440 - page 17

    Memo 17 ...

  • Bushnell LS1440 - page 18

    Memo 18 ...

  • Bushnell LS1440 - page 19

    Memo 19 ...

  • Bushnell LS1440 - page 20

    Makita Cor poration 883619D8 ...

メーカー Bushnell カテゴリー Saw

Bushnell LS1440のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LS1440の取扱説明書
- Bushnellの製品カード
- パンフレット
- またはBushnell LS1440の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bushnell LS1440の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bushnell LS1440の取り付け説明書、サービスマニュアル、簡易説明書、またはBushnell LS1440のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bushnell LS1440の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bushnell LS1440デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBushnell LS1440を使用するのを助ける技術的文書のことです。説明書は通常、全てのBushnell LS1440ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bushnellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bushnell LS1440の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBushnell LS1440の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bushnell LS1440に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bushnell LS1440デバイスの基本機能を使うにあたってのヒント。 Bushnell LS1440のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bushnell LS1440に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBushnell LS1440のメーカー/サービスへの連絡先に関する情報。

Bushnell LS1440についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBushnell LS1440の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBushnell LS1440で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)