Cisco Systems 6100の取扱説明書

12ページ 0.09 mb
ダウンロード

ページに移動 of 12

Summary
  • Cisco Systems 6100 - page 1

    CHAPTER Cisco 6100 Set Up and Installation Manual 8-1 8 Installation - Subtended Netw or k This section discusses installation procedures for adding subtended 6100s to a subtending host 6100. In this manual, the term “subtending” refers to the host 6100 node, and “subtended” refers to the do wnstream 6100 node in a subtended network. All 61 ...

  • Cisco Systems 6100 - page 2

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-2 8.1.1 Cab le Diagram - Subtending The following is an illustration of the basic cabling of a subtended 6100. Some connectors are not used because they are specific to one of the other configurations of the 6100 or because the y have been reserved ...

  • Cisco Systems 6100 - page 3

    78-5481-02 09/15/98 Installation - Subtended Network 8 Cisco 6100 Set Up and Installation Manual 8-3 8.2 Installation Pr ocedures - Subtending The following table shows a check list of the installation steps for subtended 6100s. Then subsequent subsections, as noted in the last column of the T able 8-1, discuss each of the installation steps in det ...

  • Cisco Systems 6100 - page 4

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-4 8.2.2 Connecting the DS3 Subtending Card The DS3 subtending I/O card has two sets of DS3 75-ohm coaxial BNC connectors. Each set consists of a transmit and a receiv e connector . The follo wing figure illustrates the 2x DS3 subtend card. Figure 8-2 ...

  • Cisco Systems 6100 - page 5

    78-5481-02 09/15/98 Installation - Subtended Network 8 Cisco 6100 Set Up and Installation Manual 8-5 Connect the DS3 subtending I/O card to connector J48, a 96-pin DIN connector , on the subtending host 6100 MC backplane. Refer to the Figure 8-3 for the location of these connectors. Figure 8-3 DS3 Subtending Card Connector DS3 sudtending card Syste ...

  • Cisco Systems 6100 - page 6

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-6 Figure 8-4 DS3 Subtend Card - Standoffs See Figure 8-1 for an illustration of the cabling between the system I/O card on the subtended node 6100 and the DS3 subtend card on the subtended 6100. DS3 card Existing backplane screw DS3 card standoff DS3 ...

  • Cisco Systems 6100 - page 7

    78-5481-02 09/15/98 Installation - Subtended Network 8 Cisco 6100 Set Up and Installation Manual 8-7 8.2.3 Installing the DS3 Subtend Module The DS3 NI module should be installed in slot 10 of the host 6100 before the A TU-Cs are installed in the subtended node 6100. The DS3 subtend module should be installed in slot 9 of the subtending host 6100. ...

  • Cisco Systems 6100 - page 8

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-8 Using either the ferrite beads shipped with the DS3 NI module (type 43) or ones that use ferrite material type 43 or 44 with an impedance of >200 ohms +/- 20% at 100 MHz, attach the beads close to the transmit and recei ve BNC connectors on the D ...

  • Cisco Systems 6100 - page 9

    78-5481-02 09/15/98 Installation - Subtended Network 8 Cisco 6100 Set Up and Installation Manual 8-9 Figure 8-8 shows the ferrite beads on the coaxial cable close to the BNC connectors on the DS3 subtend card. Figure 8-8 Ferrite Beads Close to BNC Connectors 8.2.5 Completing the Installation When the system I/O card on the subtended node and the DS ...

  • Cisco Systems 6100 - page 10

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-10 8.3 Adding a DS3 Subtend Car d If you hav e an existing MC and you need to add a DS3 subtend card, you will need to remov e two of the screws from the backplane, add the standoffs shipped with the card, and reuse the tw o screws. See the following ...

  • Cisco Systems 6100 - page 11

    78-5481-02 09/15/98 Installation - Subtended Network 8 Cisco 6100 Set Up and Installation Manual 8-11 If you are installing the DS3 subtending I/O card on an older MC, you will need to add the standof fs to mount the card. The follo wing procedures describe how to add the standof fs. Figure 8-4 illustrates the procedure. 1 Remov e the two screws cu ...

  • Cisco Systems 6100 - page 12

    8 Installation - Subtended Network 78-5481-02 09/15/98 Cisco 6100 Set Up and Installation Manual 8-12 ...

メーカー Cisco Systems カテゴリー Marine Sanitation System

Cisco Systems 6100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 6100の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems 6100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems 6100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems 6100の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems 6100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems 6100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems 6100デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems 6100を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems 6100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems 6100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems 6100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems 6100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems 6100デバイスの基本機能を使うにあたってのヒント。 Cisco Systems 6100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems 6100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems 6100のメーカー/サービスへの連絡先に関する情報。

Cisco Systems 6100についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems 6100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems 6100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)