Bunn CRT5 CRTF5の取扱説明書

32ページ 1.32 mb
ダウンロード

ページに移動 of 32

Summary
  • Bunn CRT5 CRTF5 - page 1

    CR T5 CR TF5 ...

  • Bunn CRT5 CRTF5 - page 2

    Page 2 INTRODUCTION This equipment will automatically brew a half-gallon batch of coffee into an awaiting dispenser. The brewer may include a hot water faucet for allied beverage use. It is only for indoor use on a sturdy counter or shelf. BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it ...

  • Bunn CRT5 CRTF5 - page 3

    Page 3 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. # 12364.0000 ...

  • Bunn CRT5 CRTF5 - page 4

    Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. Model 35 requires 3-wire, grounded service rated 120/208 or 120/240 volts ac, 20 amp, single phase, 60 Hz. Proceed as follows: Model 20 requires 2-wire, grounded service rated 120 volts ac, 20 amp, single phase, 60 Hz. P ...

  • Bunn CRT5 CRTF5 - page 5

    Page 5 MODELS W/OUT FAUCET Models CRT5, CRT5A & CRT5B 1. Remove the shipping cap from the bulkhead fitting on the rear of the brewer. 2. Attach the flare fitting from the short piece of tubing on the flow control (supplied) to the water inlet fitting at the rear of the brewer. 3. Flush the water line and securely attach it to the flare fitting ...

  • Bunn CRT5 CRTF5 - page 6

    Page 6 INITIAL SET -UP CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails. 2. Place an empty dispenser under the funnel. 3. Place the heater switch at the rear of the brewer in the “OFF” lower position. 4. Conne ...

  • Bunn CRT5 CRTF5 - page 7

    Page 7 10478 061500 2. Setting batch sizes. T o set a batch volume, first check that the SET/LOCK switch is in the “SET” position on the circuit board. Press and hold the ST AR T or BREW switch until three distinct clicks are heard, and then release the switch. (Failure to release the switch within two seconds after the third click causes the v ...

  • Bunn CRT5 CRTF5 - page 8

    Page 8 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by ...

  • Bunn CRT5 CRTF5 - page 9

    Page 9 TROUBLESHOOTING (cont.) Brew cycle will not start (cont.) Water is not hot PROBABLE CAUSE REMEDY 3. ON/OFF Switch 4. Start Switch 5. Timer 6. Solenoid Valve 7. Water strainer/flow control (.222 GPM) 1. Tank Heater Switch 2. (A) Limit Thermostat (B) Thermal Cut-Off (Brewers with Faucet) CAUTION - Do not eliminate or bypass limit thermostat or ...

  • Bunn CRT5 CRTF5 - page 10

    Page 10 TROUBLESHOOTING (cont.) Inconsistent beverage level in dispenser Consistently low beverage level in the dispenser Spitting or excessive steaming 1. Strainer /flow control (.222 GPM) 2. Syphon System 3. Lime Build-up CAUTION - Tank and tank components should be delimed regularly depending on local water conditions. Excessive mineral build-up ...

  • Bunn CRT5 CRTF5 - page 11

    Page 11 TROUBLESHOOTING (cont.) Spitting or excessive steaming (cont.) Dripping from sprayhead Water flows into tank continu- ously (ON/OFF Switch "ON") Water flows into tank continu- ously (ON/OFF Switch "OFF") Beverage overflows dispenser 2. Control Thermostat 1. Syphon System 2. Lime Build-up CAUTION - Tank and tank com- pone ...

  • Bunn CRT5 CRTF5 - page 12

    Page 12 TROUBLESHOOTING (cont.) Weak beverage Dry coffee grounds remain in the funnel Brewer is making unusal noises 1. Filter Type 2. Coffee Grind 3. Sprayhead 4. Funnel Loading 5. Water Temperature 1. Funnel Loading 1. Solenoid 2. Plumbing Lines 3. Water Supply 10478 022800 PROBLEM PROBABLE CAUSE BUNN® paper filters must be used for proper extra ...

  • Bunn CRT5 CRTF5 - page 13

    Page 13 TROUBLESHOOTING (cont.) Brewer is making unusal noises (cont.) Low beverage serving tempera- ture 4. Tank Heater 1. Warmer 2. ON/OFF Switch Remove and clean lime off the tank heater. See page 20 Refer to Service - Warmer element for testing procedures. See page 29 Refer to Service - ON/OFF Switch for testing procedures. See page 17 10478 06 ...

  • Bunn CRT5 CRTF5 - page 14

    Page 14 SERVICE This section provides procedures for testing and replacing various major components used in this brewer should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any problem. WARNING - Inspection, testing, and repair of electri- cal equipment should be performed only by qualified service pe ...

  • Bunn CRT5 CRTF5 - page 15

    Page 15 SERVICE (cont.) Test Procedures: 1. Disconnect the brewer from the power source. 2. Locate the blue wire on the control thermostat. 3. Check the voltage across the blue wire on the control thermostat and the white insert on two pole 120 volt terminal block or three pole 120/240 volt terminal blocks and the red insert on two wire 200 volt or ...

  • Bunn CRT5 CRTF5 - page 16

    Page 16 SERVICE (cont.) LIMIT THERMOSTAT Location: The limit thermostat is located inside the rear of the hood on the tank lid. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the blue and black wires from the limit thermostat. 3. Check for continuity across the limit thermostat terminals with a ohmmeter. P1800 ...

  • Bunn CRT5 CRTF5 - page 17

    Page 17 Location: The ON/OFF switch(s) are located on the front of the hood. Test Procedure: 1. Disconnect the brewer from the power source. 2. Viewing the switch from the back remove the white or red wire from the upper terminal and the black wire from the center terminal. 3. Check the voltage across the white wire or red wire and the black wire w ...

  • Bunn CRT5 CRTF5 - page 18

    Page 18 ...

  • Bunn CRT5 CRTF5 - page 19

    Page 19 SERVICE (cont.) START SWITCH Location: On brewers w/out fresh light the start switch is located in the right front of the hood. On brewers w/fresh light the start switch is located on the right side of the hood. Test Procedure: 1. Disconnect the brewer from the power supply. 2. Disconnect the blue wire and the white/red wire from the switch ...

  • Bunn CRT5 CRTF5 - page 20

    Page 20 SERVICE (cont.) TANK HEATER Location: The tank heater is located inside the tank and secured to the tank lid. Test Procedures: 1. Disconnect the brewer from the power supply. 2. Check the voltage across the black and white wires on 120 volt models or the black and red wires for 120/240 volt models, 200 volt models and 240 volt models with a ...

  • Bunn CRT5 CRTF5 - page 21

    Page 21 SERVICE (cont.) TANK HEATER (Cont.) P1168.71 FIG. 13 TANK HEATER TERMINALS 10478 061500 13. Secure sprayhead tube to hood using a hex nut. 14. Install sprayhead. 15. Reconnect the wires to the limit thermostat, tank heater and control thermostat. See limit thermo- stat and control thermostat sections in this manual when reconnecting wires. ...

  • Bunn CRT5 CRTF5 - page 22

    Page 22 SERVICE (cont.) TANK HEATER SWITCH Location: The tank heater switch is located on the rear of the brewer on the upper left side of the trunk. Test Procedure: 1. Disconnect the brewer from the power source. 2. Disconnect the black wire from the limit thermo- stat. 3. With the tank heater switch in the "ON" positionand with a voltme ...

  • Bunn CRT5 CRTF5 - page 23

    Page 23 SERVICE (cont.) TANK HEATER SWITCH (cont.) P1135.80 FIG. 15 TANK HEATER SWITCH TERMINALS 10478 061500 14. Reconnect the two black wires to the tank heater switch terminals. 15. Set tank assembly inside the hood on mounting brackets and secure with two #8-32 screws. 16. Reconnect the wires to the limit thermostat, tank heater and the control ...

  • Bunn CRT5 CRTF5 - page 24

    Page 24 Location: The thermal cut-off is located inside the hood connected to the tank heater. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the thermal cut-off from the tank heater and the black wire from the control thermostat. 3. Check for continuity across thermal cut-off termi- nals with an ohmmeter. THERMAL CU ...

  • Bunn CRT5 CRTF5 - page 25

    Page 25 SERVICE (cont.) TIMER (Early Models) Location: The timer is located inside the front of the trunk on the upper right side of component bracket. Test Procedure. 1. Disconnect the brewer from the power source. 2. Disconnect the polarized, three pin connector from the brewer wiring harness and rotate the brew timer dial fully counterclockwise. ...

  • Bunn CRT5 CRTF5 - page 26

    Page 26 SERVICE (cont.) TIMER (cont.) P1136 FIG. 19 TIMER TERMINALS 10478 061500 If voltage is present as described, the brew timer is operating properly. Reset the timer dial as required, to obtain the desired brew volume. If voltage is not present as described, replace the timer. Removal and Replacement: 1. Separate all connectors between the bre ...

  • Bunn CRT5 CRTF5 - page 27

    Page 27 DIGITAL BREW TIMER (Late Models) ...

  • Bunn CRT5 CRTF5 - page 28

    Page 28 4. Attach all wires to the replacement timer board prior to installation to the component mounting bracket. Refer to FIG. 21 when reconnecting the wires. 5. Install new circuit board with spacers (as re- quired) to the component mounting bracket. 6. Adjust the timer as described below. T imer Setting: NOTE: Prior to setting or modifying vol ...

  • Bunn CRT5 CRTF5 - page 29

    Page 29 ...

  • Bunn CRT5 CRTF5 - page 30

    L1 BLK WHI BLK BLK BLK BLK BLK VIO BRN/BLK YEL WHI/VIO LEFT FRONT WARMER LEFT REAR WARMER RIGHT FRONT WARMER RIGHT REAR WARMER BLK BLK TA N K HEA TER WHI (MODEL 20) NL 2 RED (MODEL 35) GREEN WHI WHI WHI WHI WHI WHI WHI WHI WHI WHI WHI/GRN WHI/BLU LOWER CENTER WARMER BLU WHI/RED WHI/RED WHI/RED ST ART SWITCH SOL T2 T4 T3 T5 T1 BREW TIMER BLU LIMIT T ...

  • Bunn CRT5 CRTF5 - page 31

    ...

  • Bunn CRT5 CRTF5 - page 32

    L1 BLK BLK WHI/RED WHI/RED WHI/RED BLK YEL WHI/VIO BRN/BLK VIO BLK BLK BLK LOWER CENTER WARMER ON/OFF SWITCH ON/OFF SWITCH ON/OFF SWITCH ON/OFF SWITCH ON/OFF SWITCH BLK BLK GREEN TANK HEATER WHI L2 WHI WHI WHI WHI WHI WHI WHI WHI WHI SOL BLU START SWITCH T1 T5 T3 T4 T2 WHI/BLU BREW TIMER LEFT FRONT WARMER LEFT REAR WARMER RIGHT FRONT WARMER RIGHT R ...

メーカー Bunn カテゴリー Coffeemaker

Bunn CRT5 CRTF5のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CRT5 CRTF5の取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn CRT5 CRTF5の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn CRT5 CRTF5の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn CRT5 CRTF5の取り付け説明書、サービスマニュアル、簡易説明書、またはBunn CRT5 CRTF5のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn CRT5 CRTF5の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn CRT5 CRTF5デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn CRT5 CRTF5を使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn CRT5 CRTF5ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn CRT5 CRTF5の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn CRT5 CRTF5の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn CRT5 CRTF5に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn CRT5 CRTF5デバイスの基本機能を使うにあたってのヒント。 Bunn CRT5 CRTF5のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn CRT5 CRTF5に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn CRT5 CRTF5のメーカー/サービスへの連絡先に関する情報。

Bunn CRT5 CRTF5についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn CRT5 CRTF5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn CRT5 CRTF5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)