Bunn AF PR-3の取扱説明書

17ページ 0.33 mb
ダウンロード

ページに移動 of 17

Summary
  • Bunn AF PR-3 - page 1

    B UNN ® OPERA TING & SER VICE MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 28791.0001B 1/00 ©1998 Bunn-O-Matic Corporation AF PR-2 AF PR-3 AFPR-3 VERSION DISCONTINUED The information in this manual is no longer current. ...

  • Bunn AF PR-3 - page 2

    2 INTRODUCTION This equipment supplies a premixed liquid product to the hoppers on the CDS-2 or 3 dispensers. It is for indoor use only on a sturdy counter or shelf. WARRANTY Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from de- fects in material and workmanship existing at the time of manufactur ...

  • Bunn AF PR-3 - page 3

    3 INITIAL SET -UP NOTE: This refill unit should not be used to initially fill the hopper . Running the motor for extended periods will trip the thermal switch. The thermal switch will reset, but requires up to 30 minutes of cooling time. NOTE: Hoses, clamps and product container connectors are not supplied. Fittings and labels are supplied. Make ...

  • Bunn AF PR-3 - page 4

    4 CLEANING RECOMMENDED WEEkL Y CLEANING: This should be done in conjunction with the recommended weekly cleaning of your CDS-2 or CDS-3 machine. The CDS Hoppers must be empty before starting. 1. Prepare a 1 gallon cleaning solution consisting of 1 gallon of hot water and a sanitizing cleaner which contains 3-5% chlorine based sanitizer . Mix per ma ...

  • Bunn AF PR-3 - page 5

    5 OPERA TING CONTROLS A. MAIN POWER ON/OFF The main power ON/OFF switch is located on the right of the front panel just above the power cord. B. REFILL CIRCUIT ON/OFF The refill circuit ON/OFF switches are located on the right of the front panel just above the main power switch. These allow each circuit to operate independently of the other . P205 ...

  • Bunn AF PR-3 - page 6

    6 PROBLEM 1. Empty product container 2. No power or incorrect voltage to the dispenser 3. Signal cable unplugged 4. Hopper is full 5. Fuse and fuse holder 6. Main ON/OFF switch 7. Probe box LOW/OFF/HIGH switch - es 8. Circuit board 9. Vacuum switches 10. Vacuum/Supply pump 1. Motor over heats Replace or refill (A1) Check the outlet for 120 volts o ...

  • Bunn AF PR-3 - page 7

    7 SERVICE This section provides procedures for testing and replacing various major components used in this dispenser should service become necessar y . Refer to T roubleshooting for assistance in determining the cause of any problem. WARNING - Inspection, testing, and repair of electri- cal equipment should be performed only by qualified service p ...

  • Bunn AF PR-3 - page 8

    8 Removal and Replacement: 1. Disconnect the ten pin plug from the main wiring harness to the circuit board. 2. Remove the six #4-40 screws and spacers securing the circuit board to the solenoid mounting bracket. Remove circuit board and discard. 3. Install new circuit board using #4-40 screws and spacers to secure the circuit board to the vacuum s ...

  • Bunn AF PR-3 - page 9

    9 FIG. 4 FUSE HOLDER FUSE AND FUSE HOLDER P1561 Location: The fuse holder is located on the lower right front of the autofill box just to the left of the power cord. T est Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Remove cap and fuse from fuse holder . 3. Remove fuse from the cap. 4. Check for continuity through the fuse. I ...

  • Bunn AF PR-3 - page 10

    10 Removal and Replacement:: 1. Remove the wires from the switch terminals. 2. Compress the clips inside the autofill box and gently push the switch through the opening 3. Push the new switch into the opening and spread the clips to hold switch in the autofill box. 4. Refer to Fig 7 when reconnecting the wires. P1522 FIG. 7 MAIN ON/OFF SWITCH TER ...

  • Bunn AF PR-3 - page 11

    11 FIG. 8 PROBE SWITCHES Probe Boxes: 1. Disconnect the signal cable from the probe boxes. 2. Remove probe box from CDS hopper . 3. Place the switch on the probe box in the “HIGH” position. 4. Check the resistance across the box cable pins, see Fig. 8B. PROBE SYSTEM P1523 P1539 FIG. 8B PROBE BOX CABLE PINS SERVICE (cont.) Location The probe swi ...

  • Bunn AF PR-3 - page 12

    12 SERVICE (cont.) REFILL SWITCHES FIG. 12 REFILL SWITCHES Location: The refill switches are located on the upper right front of the autofill box. T est Procedures: 1. Disconnect the dispenser from the power sour ce. 2. Disconnect the two white/red, brown/black or red/ black wires from the switch terminals. 3. Check for voltage across the white/r ...

  • Bunn AF PR-3 - page 13

    13 SERVICE (cont.) V ACUUM/SUPPL Y PUMP ASSEMBL Y FIG. 16 V ACUUM/SUPPL Y PUMP ASSEMBL Y P1560 Location: The vacuum/supply pumps are located inside the autofill box. T est Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Disconnect the white wire from the pump lead and the yellow , orange or red wire from the other lead. 3. Check ...

  • Bunn AF PR-3 - page 14

    14 SERVICE (cont.) V ACUUM/SUPPL Y PUMP TUBE INST ALLA TION 1. Separate the pump head from the pump body . Hold pump head as shown in Fig. 18, with roller in the 2, 6 10 o’clock positions. 2. Wrap tubing around rollers and hold as shown in Fig. 18. 3. Insert the slot of the tubing key (supplied), as shown in Fig. 18 on the rotor so the bottom edg ...

  • Bunn AF PR-3 - page 15

    15 V ACUUM SWITCHES FIG. 16 V ACUUM SWITCHES Location: The vacuum switches are located inside autofill box, mounted on the left side of the mounting bracket. T est Procedure: 1. Disconnect the dispenser from the power sour ce. 2. Disconnect flavor input lines. 3. Disconnect white/red, red/black or the brown/black wires on the vacuum switch. 4. Ch ...

  • Bunn AF PR-3 - page 16

    16 28791.1 011500 ...

  • Bunn AF PR-3 - page 17

    17 28791.1 011500 ...

メーカー Bunn カテゴリー Beverage Dispenser

Bunn AF PR-3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- AF PR-3の取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn AF PR-3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn AF PR-3の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn AF PR-3の取り付け説明書、サービスマニュアル、簡易説明書、またはBunn AF PR-3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn AF PR-3の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn AF PR-3デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn AF PR-3を使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn AF PR-3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn AF PR-3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn AF PR-3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn AF PR-3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn AF PR-3デバイスの基本機能を使うにあたってのヒント。 Bunn AF PR-3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn AF PR-3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn AF PR-3のメーカー/サービスへの連絡先に関する情報。

Bunn AF PR-3についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn AF PR-3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn AF PR-3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)