Clarion APX400.2の取扱説明書

16ページ 0.27 mb
ダウンロード

ページに移動 of 16

Summary
  • Clarion APX400.2 - page 1

    ...

  • Clarion APX400.2 - page 2

    INTRODUCTION The Clarion APX200.2 and APX400.2 are full-featured two-channel amplifiers. incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, including those with sate ...

  • Clarion APX400.2 - page 3

    DESCRIPTION The Clarion APX200.2 and APX400.2 two-channel amplifiers provide 2x70 watts and 2x110 watts of power into a 4 ohm load and 2x110 watts and 2x190 watts of power into a 2 ohm load. These full featured models are an excellent choice for a variety of car audio sound system configurations. The APX200.2 and APX400.2 use an unregulated MOSFET ...

  • Clarion APX400.2 - page 4

    • Gain Control - This allows you to set the nominal operating level of the amplifier . The amplifier ’ s range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high-Q” (i.e. narrow frequency ban ...

  • Clarion APX400.2 - page 5

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2 and APX400.2 both contain power and speaker connections as shown below. 5 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery + 12v Input 6. 25 Amp Fuse / 40 Amp Fuse Figure 2- ...

  • Clarion APX400.2 - page 6

    APPLICA TIONS The Clarion APX200.2 and APX400.2 2-channel car audio amplifiers can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Set X-Over Mode to LP and adjust ...

  • Clarion APX400.2 - page 7

    2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or sa ...

  • Clarion APX400.2 - page 8

    Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 318 265 199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a ...

  • Clarion APX400.2 - page 9

    INSTALLA TION This section lists Mounting and W iring Precautions for installing a Clarion APX200.2 or APX400.2. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your ...

  • Clarion APX400.2 - page 10

    4. A secure clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible snd securely connect to the car chassis to minimize resistance and avoid noise problems. 5. Add an external fuse on the amplifier ’ s positive (+) power lead and connect it as close as possible to the vehicle’s (+) ...

  • Clarion APX400.2 - page 11

    11 Figure 6. - Electrical connections for the APX200.2 or the APX400.2 ...

  • Clarion APX400.2 - page 12

    SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. T urn the Gain Control all the way counter-clockwise. 2. T urn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all T one or Equalizati ...

  • Clarion APX400.2 - page 13

    FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay , slowly increase the V olume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to T roubleshooting. Depending on your system design, the levels may become quite loud even a ...

  • Clarion APX400.2 - page 14

    14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to e ...

  • Clarion APX400.2 - page 15

    NOTES 15 ...

  • Clarion APX400.2 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX2CH-10 Rev .1 (02/00) ...

メーカー Clarion カテゴリー Power Supply

Clarion APX400.2のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- APX400.2の取扱説明書
- Clarionの製品カード
- パンフレット
- またはClarion APX400.2の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Clarion APX400.2の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Clarion APX400.2の取り付け説明書、サービスマニュアル、簡易説明書、またはClarion APX400.2のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Clarion APX400.2の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Clarion APX400.2デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがClarion APX400.2を使用するのを助ける技術的文書のことです。説明書は通常、全てのClarion APX400.2ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Clarionの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Clarion APX400.2の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははClarion APX400.2の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Clarion APX400.2に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Clarion APX400.2デバイスの基本機能を使うにあたってのヒント。 Clarion APX400.2のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Clarion APX400.2に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるClarion APX400.2のメーカー/サービスへの連絡先に関する情報。

Clarion APX400.2についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもClarion APX400.2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがClarion APX400.2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)