Porter-Cable 310の取扱説明書

17ページ 0.28 mb
ダウンロード

ページに移動 of 17

Summary
  • Porter-Cable 310 - page 1

    Laminate T rimmer Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Pleas ...

  • Porter-Cable 310 - page 2

    2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are ...

  • Porter-Cable 310 - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...

  • Porter-Cable 310 - page 4

    4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work a ...

  • Porter-Cable 310 - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • Porter-Cable 310 - page 6

    6 1 . Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Tighten Collet nut securely to prevent the bit from slipping. Never tighten collet nut without a bit. Never adjust depth of cut while motor is running. A slip ...

  • Porter-Cable 310 - page 7

    7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...

  • Porter-Cable 310 - page 8

    8 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 vo ...

  • Porter-Cable 310 - page 9

    9 SELECTING THE BIT The Model 310 is equipped with a 1 / 4 " diameter collet to accept laminate trimming bits with 1 / 4 " diameter shanks. A – Motor Unit G – Ring Spring B – Base Unit H – Clamp Knob C – Sub-Base J – Collet Nut F – Depth Adjusting Ring K – Switch A F G H C B K J H C Fig. 1 FUNCTIONAL DESCRIPTION OPERA TION ...

  • Porter-Cable 310 - page 10

    10 TO INST ALL BIT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit as follows: a. Loosen clamping knob (H) Fig. 1. b. Grasp power unit (A) Fig. 1, and pull straight up and out of the base unit (B) Fig. 1. This will also release the depth adjusting ring (F) Fig. 1, from ring springs (G) Fig. 1. 3. Lay power unit on bench wi ...

  • Porter-Cable 310 - page 11

    11 USING A LAMINA TE TRIMMER 1. Material to be trimmed must overhang the base material by a least 1 / 8 ". 2. Always wear ansi Z87.1 safety glasses while operating a laminate trimmer. 3. DISCONNECT TOOL FROM POWER SOURCE. 4. Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and ...

  • Porter-Cable 310 - page 12

    12 ASSEMBLING AND ADJUSTING BASE AND ROLLER (73100) 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit (see TO INSTALL BIT), and install the bit. 3. Position the base and roller guide assembly (A) Fig. 2, to the base unit. The alignment pin on the back of the guide base fits into hole (C) Fig. 3. 4. Place the two mounting scr ...

  • Porter-Cable 310 - page 13

    13 FLUSH TRIMMING 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Attach base and guide to trimmer as outlined under ASSEMBLING AND ADJUSTING BASE AND ROLLER. 3. Remove roller guide and replace with flush trimming guide (B) Fig. 2. This guide may be identified by the molded on letter “F”. The stud on the end of this guide must face toward the trimmer ...

  • Porter-Cable 310 - page 14

    14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST AR T Should your tool fail ...

  • Porter-Cable 310 - page 15

    15 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable • ...

  • Porter-Cable 310 - page 16

    16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable 310 - page 17

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

メーカー Porter-Cable カテゴリー Laminate Trimmer

Porter-Cable 310のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 310の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable 310の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable 310の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable 310の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable 310のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable 310の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable 310デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable 310を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable 310ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable 310の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable 310の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable 310に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable 310デバイスの基本機能を使うにあたってのヒント。 Porter-Cable 310のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable 310に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable 310のメーカー/サービスへの連絡先に関する情報。

Porter-Cable 310についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable 310の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 310で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)