Barco DP100の取扱説明書

22ページ 2.28 mb
ダウンロード

ページに移動 of 22

Summary
  • Barco DP100 - page 1

    Co oling liquid r efur bishme nt Installation manual For XLM, DP90 and DP100 R59770032/01 07/12/2006 ...

  • Barco DP100 - page 2

    Barco nv Eve nts Noordl aan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: sales.events@barco.com Visit us at the web: www.barco.com P r i n t e di nB e l g i u m ...

  • Barco DP100 - page 3

    1. Liquid C ooling Circ uit 1. LIQUID COOLING CIRCUIT Overview • Safety • Introduction • Diagnostics 1.1 Safety W ARNING : Hazardous pr oduct: Blue a ntifree ze dilu ted 1,2 et hanedio l (1/3 eth anediol – 2/3 Demi water). Not for household use. Keep out of reach of children. Harmful by oral intake. A void exposure to pregnant women. A void ...

  • Barco DP100 - page 4

    1. Liqui d Cooling Ci rcuit Parts of the liquid cooling circui t A B C H G F I K J D E Image 1-1 A DMD - Peltier cooling block. B Manometer . C Pressure vessel. D Outlet cooling circuit E Inlet cooling circuit F V ane GP u m p . H Cooling block light pipe entrance. I Flow switch. J Heat exchanger . H Transparent tube for visual check. 2 R59770032 C ...

  • Barco DP100 - page 5

    1. Liquid C ooling Circ uit Block d iagram o f the coo ling circu it Engine Pump Vane Outlet Inlet Expansion Vat Manometer Heat Exchanger Light Pipe entry Pressure relief valve (3 Bar) Vane Outlet Inlet Waterflow Sensor to SMPS Control Image 1-2 Block diagr am cooling circuit Order info li quid cooling Order numbe r Description R395198K Complete li ...

  • Barco DP100 - page 6

    1. Liqui d Cooling Ci rcuit T o oh i g ha m b i e n tt e m p e r a t u r e An Error or warning message “Ambient temp high” is displayed on the local LCD pa nel or touch panel. See manual of the projector for accessing error messages. Possible cause Solution Ambient temperature of the projector is too high. Measure the ambient temperature nearby ...

  • Barco DP100 - page 7

    1. Liquid C ooling Circ uit Possible cause Solution Defect pump. When the projector is running, you don’t feel any vibrations when touching the pump Drain the liquid cooling circuit, replace the pump, fill and pressurize the liquid cooling circuit. T i p: It’ s not ne cessary to drain the cooling circuit of the light processor . Bypass this par ...

  • Barco DP100 - page 8

    1. Liqui d Cooling Ci rcuit 6 R59770032 COOLING LIQU ID REFURBISHMENT 07/12/2006 ...

  • Barco DP100 - page 9

    2. Servicing the liquid cooling circ uit 2. SER VICING T HE LIQUID COOLING CIRCUIT W ARNING : All procedures in this chapter may on ly be performed by “qualifie d service technicians” . Definition of “qualified service tech nicians” or ”qualif ied technicians”: Persons having appropriate technica l training and experience ne cessary to ...

  • Barco DP100 - page 10

    2. Servicing the liquid coo ling circuit 2.1 Preparation for cooling liquid replacement What has to be done 1. Switch off the projector . 2. Remove the lamp unit to access the cooling liquid in- and outlet. 3. If excluding the light processor is required w hile handling the co oling circuit procedures, disconnect the circuit at the flow switch (a). ...

  • Barco DP100 - page 11

    2. Servicing t he liquid coolin g circuit OUT Image 2-3 Drain complete circui t 2. Close the valve. 3. Fill the syringe with air . Press in the valve of the male fitting when extracting air . Image 2-4 4. Couple the air filled syringe to the inlet of the cooling circuit and force air into the circuit via the syringe. L iquid will be expelled from t ...

  • Barco DP100 - page 12

    2. Servicing the liquid coo ling circuit 2.3 Filling the liq uid cooling circu it This procedure can only be used to fill an e mpty (drained) coo ling circuit. Necessary t ools • 60 cm of plastic tube with male valved fitting. • 60 cm of plastic tube with fe male valved fitting. • Syringe connected with short tube with male valved fitting. ? ...

  • Barco DP100 - page 13

    2. Servicing t he liquid coolin g circuit ab c d e f M F Image 2-7 4. Couple the filled syringe to the inlet of the cooling circuit and press the cooling liquid inside the circuit. Caution: Position the empty bottle above the liquid circuit (on top of projector). OUT a b Image 2-8 Filling cooling liq uid circuit 5. Disconnect the syringe from the c ...

  • Barco DP100 - page 14

    2. Servicing the liquid coo ling circuit 2.4 Refreshing the liquid cooling circuit Over time the cool ing liquid may show d eterioration and hen ce less effective cooling ch aracteristics. T o m ain- tain sound cooling properties, we advise ANNUAL replac ement of the cooling liquid. Necessary t ools • 2 x 60 cm of plastic tube with male valved fi ...

  • Barco DP100 - page 15

    2. Servicing t he liquid coolin g circuit OUT IN Image 2- 10 Refresh cooling circ uit 5. Switch on the projector . After projector boot-up procedure, the in ternal pump will automatically start sucking-up the fresh liquid Note: Make sure that the end of the plastic tube remains immersed in the bottle with fresh cooling liquid. 6. Switch off the pro ...

  • Barco DP100 - page 16

    2. Servicing the liquid coo ling circuit b ac d M F F M Image 2-1 1 Caution: It’s important that there is no air i nside the tube. The pump is not self priming and hence i s only capable of sucking through small volumes of air. 3. Push the male valved fitting of the filled tube into the inlet of the cooling circuit. Make sure that the inlet of th ...

  • Barco DP100 - page 17

    2. Servicing t he liquid coolin g circuit 7. Uncouple the two plastic tubes. Note: Make sure that both ends of the plastic tubes in the bottle remains immersed until the plastic tubes are uncouple from the li quid c ooli ng cir cuit . Tip : Sometimes a little cooling liquid will be spilled. Wrap a small cloth around the valved fitting while uncoupl ...

  • Barco DP100 - page 18

    2. Servicing the liquid coo ling circuit ab c d e f M F Image 2- 13 2. Couple the syringe to the inlet of the cooling circuit and press t he cooling liquid inside the circuit until the manom eter indicates 1 bar pressure. Ensure that no air bubbles are injected into the circuit. Caution: Maximum 1 bar of pressure is allowed on the liquid cooling ci ...

  • Barco DP100 - page 19

    2. Servicing t he liquid coolin g circuit Check within 24 hours whether th e pressure has stabilized close to 1 bar . If not, search for leak age. 2.7 Calibrating the liquid cooling circuit T o check if the pressure vessel is correctly calibrated you m ay connect the syringe with the cooling c ircuit and measu re the a mount of liqui d that i s aut ...

  • Barco DP100 - page 20

    2. Servicing the liquid coo ling circuit ab c d e f M F Image 2- 16 3. Fill the pressure vessel with liquid as follows: a) Couple the syringe with the inlet of the cooling circuit. b) Increase the pressure by pushing in the piston of the syringe (maximum 1 bar indi cated on the m anometer). c) While pressing, expel air from the pressure vessel. d) ...

  • Barco DP100 - page 21

    2. Servicing t he liquid coolin g circuit 4. Now that the pressure vessel is liquid filled you have to increase the pressure to 1 bar by pushing in the piston of the syringe. Then immediately extract 75 ml back into the syringe by doing the following: a) T aking note of the liquid level already in the syringe, release the plunger . b) Now fill the ...

  • Barco DP100 - page 22

    2. Servicing the liquid coo ling circuit The air hose fitting of the air pump mu st be of the Shrader valve type (A) to match with the pressure vessel, so the Presta valve type (B) has to be removed. Futhermore, the pin (C) inside the Shrader valve has to be removed as well. A B A A B C C Check within 24 hours whether th e pressure has stabilized c ...

メーカー Barco カテゴリー Fan

Barco DP100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DP100の取扱説明書
- Barcoの製品カード
- パンフレット
- またはBarco DP100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Barco DP100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Barco DP100の取り付け説明書、サービスマニュアル、簡易説明書、またはBarco DP100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Barco DP100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Barco DP100デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBarco DP100を使用するのを助ける技術的文書のことです。説明書は通常、全てのBarco DP100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Barcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Barco DP100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBarco DP100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Barco DP100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Barco DP100デバイスの基本機能を使うにあたってのヒント。 Barco DP100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Barco DP100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBarco DP100のメーカー/サービスへの連絡先に関する情報。

Barco DP100についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBarco DP100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBarco DP100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)