AEG Thyro-S H1の取扱説明書

48ページ 1.92 mb
ダウンロード

ページに移動 of 48

Summary
  • AEG Thyro-S H1 - page 1

    Ethernet Bu s Module Pr ofi Net PERFECT IN FORM AND FUNCTION Oper ating Instruction s • Thyr o-S ...H1, ..HRL1 • Thyr o-A ...H1, ..HRL1, ..HRLP1 • Thyr o-A …C01, ..C0 2, ..C03, ..C05, ..C0 7 • Thyr o-P ower Manager • Thyr o-Step Controller • Thyr o-Measurement Unit ...

  • AEG Thyro-S H1 - page 2

    2 Contents 1. Introduction 5 1.1 General 5 1.2 Special features 5 1.3 Type designation 5 1.4 Abbreviations 5 1.5 Warranty 5 2. Safety 6 2.1 Identification in the operating instructions 6 2.2 General danger information 6 2.3 Operator requirements 7 2.4 Personnel requirements 7 2.5 Intended use 7 2.6 Use of the device 7 2.6.1 Operation 7 2.6.2 Prior ...

  • AEG Thyro-S H1 - page 3

    3 9. Connection diagrams Thyro-A 30 10. Connection diagrams Thyro-S 31 1 1. Connection diagrams Thyro-Step Controller 32 12. Specific notes 33 12.1 Installation 33 12.2 Service 33 13. T echnical Data 33 14. Dimension drawings 34 15. Accessories and options 34 16. Approvals and conformity 34 17. Appendix A Acyclic parameter tables 36 List of figures ...

  • AEG Thyro-S H1 - page 4

    4 Contact Technical queries Do you have any technical queries regarding the subjects dealt with in these operating instructions? If so, please get in touch with our team for power controllers: Tel. +49(0)2902 763-520 or +49(0)2902 763-290 Commercial queries Do you have any commercial queries on power controllers? If so, please get in touch with our ...

  • AEG Thyro-S H1 - page 5

    5 1. Introduction The operating instructions below serve only as an addition to be used in conjunction with the operating instructions of the AEG Power Solutions Thyro-A power controller, Thyro-S power switch, and Thyro- Power Manager in the versions of the types indicated on the covering page. The safety instructions con- tained therein are to be ...

  • AEG Thyro-S H1 - page 6

    6 2. Safety 2.1 Identification in the operating instructions In these operating instructions, there are warnings before dangerous actions. These warnings are divided into the following danger categories: DANGER Dangers that can lead to serious injuries or fatal injuries. W ARNING Dangers that can lead to serious injuries or considerable damage to p ...

  • AEG Thyro-S H1 - page 7

    7 NOTE Communication errors To avoid communication errors please note the following points: > Use shielded cables. > Undertake grounding of the bus module (X1.7 to X8.7). Do not ground additionally at the power controller. 2.3 Operator requirements The operator must ensure the following: - The safety regulations of the operating instructions ...

  • AEG Thyro-S H1 - page 8

    8 2.6.2 Prior to installation / commissioning - If stored in a cold environment: ensure that the device is absolutely dry. (Allow the device a period of at least two hours to acclimatize before commissioning) - Ensure sufficient ventilation of the cabinet if mounted in a cabinet. - Observe minimum spacing. - Ensure that the device cannot be heated ...

  • AEG Thyro-S H1 - page 9

    9 3. Functions 3.1 Processing the setpoint Thyro-S Only local setpoints, no bus setpoint Switching signal (24DC) at the control terminal X22.1 of the Thyro-S > No wiring of the terminal point X22.4 at the power controller - The bus module is fully functional. The analog signal from the control terminal X22.1 is used as setpoint (on/off). Setpoin ...

  • AEG Thyro-S H1 - page 10

    10 3.3 Processing the setpoint Thyro-Step Controller Only local setpoints, no bus setpoint Analog input at control terminal X6.1 or X6.4 (depending on X6.7) of the TSC > Do not connect anything to terminal X2.1 of the power controller. - The bus module is fully functional. The analog signal from the control terminal X6.1 or X6.4 is used as setpo ...

  • AEG Thyro-S H1 - page 11

    11 4. Installation DANGER Dangers during Installation Risk of injury / Risk of damage to the device or plant Observe all safety regulations in the chapter “Safety”. 4.1 Connection terminals (overview) T ab.1 Connecting terminals (overview) Connection diagram see page 30. 4.2 Connecting a 24 V power supply > Switch off the main power supply i ...

  • AEG Thyro-S H1 - page 12

    12 5. Settings 5.1 Setting the protocol The Ethernet bus module supports various real time Ethernet bus systems. The desired system can be selected using the rotary switch “Protocol”. For ProfiNet this needs to be set to 0. 5.2 Setting the number of slots The number of devices which are connected to the Ethernet bus module is set with the rotar ...

  • AEG Thyro-S H1 - page 13

    13 5.4 Operating display of the bus module T able 2 Operating display of the bus module Operating status of the Ethernet bus module Status LED of the Ethernet Ports LED Color Status Meaning SYS Green On Operating system running Red Flashing with 1Hz Error in boot process Red On Waiting for boot process (check position of “Protocol” switch) Off ...

  • AEG Thyro-S H1 - page 14

    14 6. Operation 6.1 Start configuration (parameterization) Via the parameterization (in step 7 – HW Config, double-click on slot 0 of the bus module, parameter tab) the following settings can be undertaken. No connection (slot 1-8): Here you can set what should happen with the output data of the devices if the connection to the master is interrup ...

  • AEG Thyro-S H1 - page 15

    15 T ab. 3 Interpretation of the master setpoint with Thyro-S T ab. 4 Cyclic input and output data with Thyro-S ..H1 T ab. 5 Cyclic input and output data with Thyro-S ..HRL1 T ab. 5b Thyro-S Faults Setpoint (Master) Status (return value) (Total setpoint) 0 to 409 = OFF 0 = 410 to 1091 1/5 819 1092 to 1706 = 1/3 1365 = 1707 to 3071 1/2 2047 3072 to ...

  • AEG Thyro-S H1 - page 16

    16 T ab. 5b Thyro-S Status 6.4 Input and output data Thyro-A T ab. 6 Cyclic input and output data with Thyro-A 1A...H1 T ab. 7 Cyclic input and output data with Thyro-A 1A...HRL1 Description Bit LEDs Relay Pulse inhib active Bit 0 none open (bridge X2.1-X2.2 open) Bit 0 none open Mains frequency is 60Hz Bit 2 none open Relay status Bit 8 none open ...

  • AEG Thyro-S H1 - page 17

    17 T ab. 8 Cyclic input and output data with Thyro-A 1A...HRLP1 T ab. 9 Cyclic input and output data with Thyro-A 2A...H1 T ab. 10 Cyclic input and output data with Thyro-A 2A...HRL1 Offset Input data, actual values Data type Size Unit 0 Load voltage L1 float 4 [V] 4 Load current L1 float 4 [A] 8 Power L1 float 4 [W] 12 Mains voltage L1 integer 2 [ ...

  • AEG Thyro-S H1 - page 18

    18 T ab. 1 1 Cyclic input and output data with Thyro-A 2A...HRLP1 T ab. 12 Cyclic input and output data with Thyro-A 3A...H1 Offset Input data, actual values Data type Size Unit 0 Load voltage L1 float 4 [V] 4 Load voltage L3 float 4 [V] 8 Load current L1 float 4 [A] 12 Load current L2 float 4 [A] 16 Load current L3 float 4 [A] 20 Power L1 float 4 ...

  • AEG Thyro-S H1 - page 19

    19 T ab. 13 Cyclic input and output data with Thyro-A 3A...HRL1 T ab. 14 Cyclic input and output data with Thyro-A 3A...HRLP1 Offset Input data, actual values Data type Size Unit 0 Load voltage L1 float 4 [V] 4 Load voltage L2 float 4 [V] 8 Load voltage L3 float 4 [V] 12 Load current L1 float 4 [A] 16 Load current L2 float 4 [A] 20 Load current L3 ...

  • AEG Thyro-S H1 - page 20

    20 T ab. 14a Thyro-A Fault T ab. 14b Thyro-A Status Description Bit LEDs Relay Frequency measurement outside of 47Hz to 63Hz Bit 0 Pulse Inhibit LED flashing slowly open SYNC error, no cero crossing within the gate Bit 1 Pulse Inhibit LED flashing slowly open Temperature monitoring triggered Bit 2 Load Fault LED flashing slowly open Load fault Bit ...

  • AEG Thyro-S H1 - page 21

    21 T ab. 15 Cyclic input and output data with Thyro-A 1A...C01 Offset Input data, actual values Data type Size Unit 0 Load voltage L1 float 4 [V] 4 Load current L1 float 4 [A] 8 Power L1 float 4 [W] 12 Mains voltage L1 integer 2 [V] 14 Switch-on time TS integer 2 [period] 16 Switch-on angle alpha integer 2 [0.01 °el] 18 Total setpoint integer 2 40 ...

  • AEG Thyro-S H1 - page 22

    22 T ab. 18 Cyclic input and output data with Thyro-A 1A...C05 Offset Input data, actual values Data type Size Unit 0 Load voltage phase 1 float 4 [V] 4 Load current phase 1 float 4 [A] 8 Load current phase 2 float 4 [A] 12 Total load current float 4 [A] 16 Power phase 1 float 4 [W] 20 Power phase 2 float 4 [W] 24 Total power float 4 [W] 28 Mains v ...

  • AEG Thyro-S H1 - page 23

    23 6.5 Input and output data Thyro-Power Manager T ab. 21 Cyclic input and output data TPM automatic mode T ab. 22 Cyclic input and output data TPM manual mode Offset Input data, actual values Data type Size Unit 0 AC input 1 float 4 [A],[V] 4 AC input 2 float 4 [A],[V] 8 AC input 3 float 4 [A],[V] 12 Power float 4 [W] 16 Energy float 4 [kWh] 20 DC ...

  • AEG Thyro-S H1 - page 24

    24 6.6 Input and output data Thyro-Step Controller T ab. 23 Cyclic input and output data TSC mode 6.7 Input and output data Thyro Input/Output Unit T ab. 24 Cyclic input and output data TIO mode Offset Input data, actual values Data type Size Unit 0 AC input 1 float 4 [A],[V] 4 AC input 2 float 4 [A],[V] 8 AC input 3 float 4 [A],[V] 12 Power float ...

  • AEG Thyro-S H1 - page 25

    25 6.8 Input and output data Thyro-Measurement Unit T ab. 25 Cyclic input and output data TMU mode Offset Input data, actual values Data type Size Unit 0 AC input 1 float 4 [A],[V] 4 AC input 2 float 4 [A],[V] 8 AC input 3 float 4 [A],[V] 12 Power float 4 [W] 16 Energy float 4 [kWh] 20 DC input 1 integer 2 4096=100% 22 DC input 2 integer 2 4096=100 ...

  • AEG Thyro-S H1 - page 26

    26 6.9 Acyclic data transmission (parameterization) Via the acyclic parameter data transmission, parameters of the devices can be changed or selected. Cyclical and acyclical services can be used in the network simultaneously. Read data record “RDREC”: For reading access to a data record, the slot, index and length of the data record must be ent ...

  • AEG Thyro-S H1 - page 27

    27 7. External connections 7.1 Power supply +24V to X11, current consumption approx. 150mA The foregoing circuit diagram shows the connection of the bus module supply 24V DC (approx. 150mA) bridge (contact) Thyro-S: see chapter 3.1 Thyro-a: see chapter 3.2 TPM: see chapter 3.3 X1 - X8 to the power controllers ...

  • AEG Thyro-S H1 - page 28

    28 7.2 Operating elements and terminal blocks This chapter describes the available terminal blocks, plug connectors and operating elements. Configuration of the 7 pin connector of slots X1 to X8: 1 Switched ground potential. All pins 1 of slots X1 – X8 are connected. 2 RxD 3 TxD 4 Ground 5 Switchable ground potential. The slots X1 – X8 can be s ...

  • AEG Thyro-S H1 - page 29

    29 8. Interfaces 8.1 System interface The bus module is connected with the relevant system interfaces of the power controllers via X1 to X8 (four-wire, 2x2 twisted, shared shielding). The transmission rate is 38,400 Bd. The asynchronous characters are transferred with 8bit, no parity, one stop bit. The protocol begins with STX, followed by an ident ...

  • AEG Thyro-S H1 - page 30

    30 9. Connection diagrams Thyro-A Fig. 2 Connection diagram Thyro-A bus setpoint is active bus setpoint/ analog input bus setpoint/analog input bus setpoint/analog input bus setpoint/ analog input group switching selective switching bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input analog in ...

  • AEG Thyro-S H1 - page 31

    31 10. Connection diagrams Thyro-S Fig. 3 Connection diagram Thyro-S bus setpoint/analog input bus setpoint/analog input group switching selective switching bus setpoint is active analog input is active setpoint *blank bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog in ...

  • AEG Thyro-S H1 - page 32

    32 11. Connection diagrams TSC Fig. 4 Connection diagram TSC bus setpoint/analog input bus setpoint/analog input group switching selective switching bus setpoint is active analog input is active bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog input bus setpoint/ analog ...

  • AEG Thyro-S H1 - page 33

    33 12. Specific notes 12.1 Installation The bus modules can be installed in any desired order. 12.2 Service The devices supplied have been produced in accordance with the quality standard ISO 9001. Should there be faults in spite of this, our 24 hour service hotline is on hand, tel.: +49 (0)2902 763-100. 13. Technical Data Power supply 24V DC 150mA ...

  • AEG Thyro-S H1 - page 34

    34 14. Dimension drawings 15. Accessories and options Ready-made bus module-side shielded cable. A set of cable consists of 4 connection cables for connecting 4 power controllers. Order number 2000 000 848 Bus module connection cable for 4 controllers, 2.5 m long Order number 2000 000 849 Bus module connection cable for 4 controllers, 1.5 m long 16 ...

  • AEG Thyro-S H1 - page 35

    35 In detail ProfiNet IEC 61158 IEC 61784 Built-in device (VDE0160) EN 50 178 Storage temperature (D) -25°C - +55°C Transport temperature -25°C - +70°C Operating temperature (better B) -10°C - +55°C Humidity class B EN 50 178 tab. 7 (EN 60 721) Degree of contamination 2 EN 50 178 tab. 2 Air pressure 900mbar * 1000m above sea level Degree of p ...

  • AEG Thyro-S H1 - page 36

    36 17. Appendix A 1. Acyclic parameter table Thyro-S; Thyro-A; -C01; -C02; -C03; -C05 Table A: Thyro-S.., Thyro-A.., Thyro-A-C01; -C02; -C03; -C05 controller parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 I_TYP Controller type current u16 0… 2 U_TYP Controller supply voltage u16 0…1000 3 P_TYP Cont ...

  • AEG Thyro-S H1 - page 37

    37 1S 1A 2A 3A 1A Unit R / W H1 HRL1 H1 HRL1 HRLP H1 HRL1 HRLP H1 HRL1 HRLP C01 C02 C03 C05 Default Note Index A r x x x x x x x x x x x x x x x type 1 V r x x x x x x x x x x x x x x x type 2 W r x x x x x x type H RLP1 3 r/w * x x x x x x x x x x x x x TAKT S1.1-2 6 ˚ el r/w * x x x x x x x x x x x 60 ˚ el R201 7 period r/w * x x x x x x x x x ...

  • AEG Thyro-S H1 - page 38

    38 2. Acyclic parameter table Thyro-C07 Table B: Thyro-C07 controller parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 I_TYP Controller type current u16 0… 2 U_TYP Controller supply voltage u16 0…1000 3 P_TYP Controller type output power u32 0… 6 BETR Operating mode u16 0…3 reserved, TAKT, VAR, Q ...

  • AEG Thyro-S H1 - page 39

    39 unit R / W Default Note Index A r type 1 V r type 2 W r type H RLP1 3 r/w * TAKT S1.1-2 6 °el r/w * 60°el R201 7 r/w * 8 period r/w 6 period 9 period r/w* 50 period R201 10 period r/w * 3 period R201 11 period r/w 50 period 12 period r/w 0 period 13 °el r/w 180°el 14 °el r/w 0°el 15 r/w * Uload2 S1.3-5 power only with H RLP1 16 r/w 20 17 r ...

  • AEG Thyro-S H1 - page 40

    40 3. Acyclic parameter table Thyro-Power Manager Table C: TPM parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 W1_TYP Type value transformer 1 u16 1...65535 2 W2_TYP Type value transformer 2 u16 1...65535 3 W3_TYP Type value transformer 3 u16 1...65535 4 W_CTRL Transformer setting u16 0...65535 bit code ...

  • AEG Thyro-S H1 - page 41

    41 Unit R / W Default Note Index r/w 100 1 r/w 100 2 r/w 100 3 r/w 8 4 r/w 230 5 r/w * 50 R309 7 r/w * 10 S2 8 r/w 0 9 r/w 5 10 r/w 10 11 r/w 15 12 r/w 20 13 r/w 25 14 r/w 30 15 r/w 35 16 r/w 40 17 r/w 45 18 4096=10V r/w 0 39 1/819 r/w 819 40 r/w 1 41 4096=10V r/w 0 42 1/819 r/w 819 43 r/w 2 44 4096=10V r/w 0 45 1/819 r/w 819 46 r/w 3 47 4096=10V r ...

  • AEG Thyro-S H1 - page 42

    42 4. Acyclic parameter table Thyro-Step Controller Table D: TSC parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 W1_TYP Type value transformer 1 u16 1...65535 2 W2_TYP Type value transformer 2 u16 1...65535 3 W3_TYP Type value transformer 3 u16 1...65535 4 W_CTRL Transformer setting u16 0...65535 5 U_TY ...

  • AEG Thyro-S H1 - page 43

    43 Unit R / W Default Note Index r/w 100 1 r/w 100 2 r/w 100 3 r/w 8 4 r/w 230 5 r/w * 50 R309 7 r/w * 11 S2 8 r/w * 2978 9 r/w * 5956 10 r/w * 8934 11 r/w * 11912 12 r/w * 14890 13 r/w * 17868 14 r/w * 20846 15 r/w * 23824 16 r/w * 26802 17 r/w * 29780 18 r 27 20/4096mA r/w 0 31 20/4096mA r/w 4096 32 20/4096mA r/w 0 37 20/4096mA r/w 4096 38 4096=1 ...

  • AEG Thyro-S H1 - page 44

    44 5. Acyclic parameter table Thyro-Measurement Unit Table D: TMU parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 W1_TYP Type value transformer 1 u16 1...65535 2 W2_TYP Type value transformer 2 u16 1...65535 3 W3_TYP Type value transformer 3 u16 1...65535 4 W_CTRL Transformer setting u16 0...65535 bit c ...

  • AEG Thyro-S H1 - page 45

    45 Unit R / W Default Note Index r/w 100 1 r/w 100 2 r/w 100 3 r/w 8 4 r/w 230 5 r/w * 50 R309 7 4096=10V r/w 0 39 1/819 r/w 819 40 r/w 1 41 4096=10V r/w 0 42 1/819 r/w 819 43 r/w 2 44 4096=10V r/w 0 45 1/819 r/w 819 46 r/w 3 47 4096=10V r/w 0 48 1/819 r/w 819 49 r/w 4 50 4096=10V r/w 0 51 1/819 r/w 819 52 r/w 9 53 4096=10V r/w 0 54 1/819 r/w 819 5 ...

  • AEG Thyro-S H1 - page 46

    46 6. Acyclic parameter table Thyro Input-Output Unit Table F: TIO parameters slot 1-8 Controller parameter Index Symbol Name Data type Value range Combo-opt. 1 W1_TYP Type value transformer 1 u16 1...65535 2 W2_TYP Type value transformer 2 u16 1...65535 3 W3_TYP Type value transformer 3 u16 1...65535 4 W_CTRL Transformer setting u16 0...65535 bit ...

  • AEG Thyro-S H1 - page 47

    47 Unit R / W Default Note Index r/w 100 1 r/w 100 2 r/w 100 3 r/w 8 4 r/w 230 5 r/w * 50 R309 7 4096=10V r/w 0 39 1/819 r/w 819 40 r/w 1 41 4096=10V r/w 0 42 1/819 r/w 819 43 r/w 2 44 4096=10V r/w 0 45 1/819 r/w 819 46 r/w 3 47 4096=10V r/w 0 48 1/819 r/w 819 49 r/w 4 50 4096=10V r/w 0 51 1/819 r/w 819 52 r/w 9 53 4096=10V r/w 0 54 1/819 r/w 819 5 ...

  • AEG Thyro-S H1 - page 48

    Emil-Siepmann-Str . 32 5958 1 W ar stein-Belecke Deut schland T el.: +49(0)290 2 763 -520 / -290 Fax: +49(0)290 2 763 -120 1 www .aegpowercontr ollers .com www .aegps.com AEG is a r egistered tr ademark used under license fr om AB Electrolux Betriebs anleitung/Oper ating In struction s 80000 29997 BAL, en 0 7/1 0; printed in Germany , subject to ch ...

メーカー AEG カテゴリー Network Card

AEG Thyro-S H1のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Thyro-S H1の取扱説明書
- AEGの製品カード
- パンフレット
- またはAEG Thyro-S H1の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AEG Thyro-S H1の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AEG Thyro-S H1の取り付け説明書、サービスマニュアル、簡易説明書、またはAEG Thyro-S H1のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AEG Thyro-S H1の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AEG Thyro-S H1デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAEG Thyro-S H1を使用するのを助ける技術的文書のことです。説明書は通常、全てのAEG Thyro-S H1ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AEGの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AEG Thyro-S H1の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAEG Thyro-S H1の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AEG Thyro-S H1に関してこのドキュメントで見つけることができる全てのヒントの目次
3. AEG Thyro-S H1デバイスの基本機能を使うにあたってのヒント。 AEG Thyro-S H1のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AEG Thyro-S H1に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAEG Thyro-S H1のメーカー/サービスへの連絡先に関する情報。

AEG Thyro-S H1についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAEG Thyro-S H1の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAEG Thyro-S H1で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)