日本語 dropdown-ico

Cisco Systems PG30 G-.TNの取扱説明書

24ページ 0.87 mb
ダウンロード

ページに移動 of 24

Summary
  • Cisco Systems PG30 G-.TN - page 1

    BURNERS BRULEURS BRENNER QUEMADORES BRUCIA T ORI Complying with EMC 89/336/CEE LV 73/23/CEE T echnical Documentation CIB Unigas S.p.a. - Campodarsego (PD) M03978CA Rev . 00 10/99 MANUAL FOR - INST ALLA TION - OPERA TION - MAINTENANCE LIGHT OIL BURNERS G18 G-.SP PG25 G-.SP PG30 G-.TN FOREWORD Page 2 PARTE I: INSTALLATION Page 4 PARTE II: OPERATION P ...

  • Cisco Systems PG30 G-.TN - page 2

    2 PREF ACE THIS MANUAL IS SUPPLIED AS AN INTEGRAL AND ESSENTIAL PART OF THE PRODUCT AND MUST BE DELIVERED TO THE USER. INFORMATION INCLUDED IN THIS SECTION ARE DEDICATED BOTH TO THE USER AND TO PERSONNEL FOLLOWING PRODUCT INSTALLATION AND MAINTENANCE. THE USER WILL FIND FURTHER INFORMATIONS ABOUT OPERATING AND USE RESTRICTIONS, IN THE SECOND SECTIO ...

  • Cisco Systems PG30 G-.TN - page 3

    3 FOREWORD 3) GENERAL INSTRUCTIONS DEPENDING ON FUEL USED 3A) ELECTRICAL CONNECTION * For safety reasons the unit must be efficiently earthed and installed as required by current safety regulations. * It is vital that all saftey requirements are met. In case of any doubt, ask for an accurate inspection of electrics by qualified personnel, since the ...

  • Cisco Systems PG30 G-.TN - page 4

    4 AB B L C C L D E G KH P M G1 8 S P 275 90 200 365 475 340 255 115 230 125 121÷134 M 8 Fig. 1 P ART I: INST ALLA TION MANUAL TECHNICAL DA T A BURNER MODEL IDENTIFICATION Burners are identified by burner type and model. Burner type identification is described as follow: Type: G18 Model: G-. SP. S. *. A. (1) (2) (3) (4) (5) (6) (1) BURNER TYPE G18 ...

  • Cisco Systems PG30 G-.TN - page 5

    5 Fig. 1a Fig. 2 Fig. 3 Fig. 3a 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 6 8 10 12 14 16 18 20 -1 0 1 2 3 4 10 12 14 16 18 20 22 24 26 28 30 -1 -0 . 5 0 0.5 1 1.5 2 2.5 3 10 12 14 16 18 20 22 24 26 28 30 32 34 AB B L C C L D E FGKHP M PG 25 SP PG 30 SP 515 155 345 660 85 0 267 260 520 133 29 0 125 155 M 10 PERFORMANCE CURVES OVERALL DIMENSIONS INSTALLAT ...

  • Cisco Systems PG30 G-.TN - page 6

    6 MOUNTINGS AND CONNECTIONS The burners are despatched in cardboard packages. The packaging contains the following items: 1 burner; 2 flexible light oil tubes; 1 light oil filter; 1 gasket to be inserted between the burner and the boiler; 1 this manual, the Guarantee Certificate and the test certificate. T o get rid of the burner’s packing and in ...

  • Cisco Systems PG30 G-.TN - page 7

    7 G18SP PG25SP PG30TN Fig. 6 Fig. 5 Fig. 5b Fig. 5a ...

  • Cisco Systems PG30 G-.TN - page 8

    8 BAR G P H 8 9 1 01 11 21 31 41 51 6 1 71 8 1. 75 6. 02 6. 38 6. 73 7. 05 7. 37 7. 67 7. 96 8. 24 8. 51 8. 77 9. 02 2. 00 6. 88 7. 29 7. 69 8. 06 8. 42 8. 77 9. 10 9. 42 9. 72 10. 02 10. 31 2. 25 7. 74 8. 20 8. 65 9. 07 9. 47 9. 86 10. 23 10. 59 10. 94 11. 28 11. 60 2. 50 8. 59 9. 12 9. 61 10. 08 10. 53 10. 96 11. 37 11. 77 12. 16 12. 53 12. 89 3. ...

  • Cisco Systems PG30 G-.TN - page 9

    9 Fig. 7 Fig. 9 Fig. 8 LIGHT OIL PUMPS SUNTEC AS57C Suction height: 0.5 bar Advised value to prevent air separation from oil: 0.35 bar Rated speed: max. 2850 rpm Operation viscosity: from 2 to 12 cSt Inlet pressure: max. 2 bar DELTA VM2RL2 Suction height: 0.5 bar Advised value to prevent air separation from oil: 0.35 bar Rated speed: max. 3500 rpm ...

  • Cisco Systems PG30 G-.TN - page 10

    10 VBS VBS + - Fig. 12 Fig. 11 Fig. 10 Fig. 12a AIR FLOW ADJUSTMENT Burner G18SP Loose the screw VBS and rotate the air damper in the desired position, to set the air flow. At the end of settings, tight the screw VBS. Burners PG25SP - PG30TN Loose the screw VBS and set the air flow, working directly on the air damper. At the end of settings, tight ...

  • Cisco Systems PG30 G-.TN - page 11

    11 P ART II: OPERA TION MANUAL LIMIT A TIONS OF USE THE BURNER IS AN APPLIANCE DESIGNED AND CONSTRUCTED TO OPERA TE ONL Y AFTER BEING CORRECTL Y CONNECTED TO A HEA T GENERA TOR (E.G. BOILER, HOT AIR GENERA TOR, FURNACE, ETC.), ANY OTHER USE IS TO BE CONSIDERED IMPROPER AND THEREFORE DANGEROUS. THE USER MUST GUARANTEE THE CORRECT FITTING OF THE APPL ...

  • Cisco Systems PG30 G-.TN - page 12

    12 C AR VRT R C V Fig. 13 Fig. 13a ABCD 6 0 ° 6446 4 5 ° 1 0 546 6 0 ° 8446 4 5 ° 1 2 546 6 0 ° 8446 4 5 ° 1 2 546 G1 8 S P PG 28 SP PG 30 TN P ART III: MAINTENANCE At least once a year carry out the following maintenance procedures. If servicing is on a seasonal basis, it is recommended at the end of the season; routine sevice should be carr ...

  • Cisco Systems PG30 G-.TN - page 13

    13 Fig. 14 CHECK OF THE IONIZA TION CURRENT To check the detector signal follow the prcedure shown in fig. 14. If the signal is not within the prescribed range, check the electrical contacts; check also that the combustion head is clean and the photoelectric sensor is correctly positioned. Replace it if necessary. TERMINAL BLOCK MC Scale µA DC Min ...

  • Cisco Systems PG30 G-.TN - page 14

    14 ELECTRICAL DIAGRAM code 01-369 BURNER G18SP ELECTRICAL DIAGRAM code 04-575 BURNER PG25SP 1 - Electric supply 230V 50Hz 2N a.c. 2 - Don't reverse Phase and Neutral 3 - Make sure that the burner is properly hearted 1 - Electric supply 230V 50Hz 2N a.c. 2 - Don't reverse Phase and Neutral 3 - Make sure that the burner is properly hearted ...

  • Cisco Systems PG30 G-.TN - page 15

    15 ELECTRICAL DIAGRAM code 04-574 BURNER PG30TN EVG1 Light oil solenoid valve I st stage EVG2 Light oil solenoid valve II nd stage F Fuses FR Photoresistor IL Main switch L Phase LF Burner operation light LB Burner lockout light LEVG1 EVG1 opening signalization light LEVG2 EVG2 opening signalization light LOA24/BOA64 Flame monitor device MA Power s ...

  • Cisco Systems PG30 G-.TN - page 16

    16 SP ARE P ARTS BURNER G18SP MAINTENANCE POS. D E SC RI PTIO N C OD E POS. D E SC R IPT IO N C OD E 1 HO USI NG 3010019 19 B LA ST T UB E 3090055 2 CO NDE NSE R 60 30004 20 CO M BUS T I O N HE A D 3060115 3 M O T O R 218000 9 21 E LECT RO DE S UPP O RT 228001 6 4 F LA M E CO NT RO L DEV I CE LO A 24 20 20445 22 G A SK ET 211003 1 5 S O CKE T F O R ...

  • Cisco Systems PG30 G-.TN - page 17

    17 SP ARE P ARTS BURNERS PG25SP - PG30TN MAINTENANCE POS. D E SC R IPTI ON PG 2 5SP PG 30 TN 1 E LECT RI C BO A RD 610008 6 61 00086 2 T HERM A L RELA Y -- - -- - 3 S OC K E T F O R F LA M E CO NT RO L DE V I CE 203041 5 203041 5 4 F LA M E C O NT RO L DE V I CE 202044 5 2020445 5C O N T A C T O R - - - - - - 6 I G NI TI O N T RA NSF O RM ER 217010 ...

  • Cisco Systems PG30 G-.TN - page 18

    18 APPENDIX: COMPONENTS CHARACTERISTICS FLAME CONTROL DEVICE LANDIS LOA24 Page 18 LIGHT OIL PUMPS Page 19 LANDIS AUTOMA TIC CONTROLLER LOA24 FOR LIGHT OIL BURNERS Use LOA... safety devices are intended for use in conjunction with QRB... photoresistors, for lighting and controlling low capacity forced air diesel burners with max. capacity 30 kg/h in ...

  • Cisco Systems PG30 G-.TN - page 19

    19 T echnical characteristics Voltage 220V-15%..240V+10% or 100V -15%...110V+10% Frequency 50...60Hz +/- 6% External fuse max.10A slow action Contact flow: - terminal 1 5 A - terminal 3 5A (incl.capacity absorbed by motor and pre- heater) Terminal flow: - terminals 4, 5 &10 1A - terminals 6&7 2A - terminal 8 5A Absorbed cap 3VA Protection I ...

  • Cisco Systems PG30 G-.TN - page 20

    20 SUNTEC AS oil pumps - Oil - Flow up to 75 1/h (c.600,000 kcal/h - 700 kW) - Twin-pipe system - Single-pipe system Technical data Mounting On flange or hub in acccordance with standards DIN 24220 and ISO/TC 109 SC 3 DP 5062F Threads round-headed in accordance with ISO R 228-NFE 03005(DIN2S9) Supply and return R 1/4" Delivery R 1/8" Pres ...

  • Cisco Systems PG30 G-.TN - page 21

    21 Operation The gear-set draws oil from the tank through the built-in filter and transfers it to the valve that regulates the oil pressure or tne nozzle line. All oil which does not go through the nozzle line will be dumped through the valve back to the return line or, if it is a one-pipe installation, back to the suction port in the gear-set. The ...

  • Cisco Systems PG30 G-.TN - page 22

    22 T win pipe installation Single pipe installation (remove the by-pass plug “P”) A Closed by-pass solenoid valve B Opened by-pass solenoid valve C Opened cut-off solenoid valve D Closed cut-off solenoid valve 1 Manometer plug 2 To nozzle 3 Shaft seal 4 Return to suction 5 By-pass plug 6 Return (twin pipe installation) 7 Suction (twin pipe inst ...

  • Cisco Systems PG30 G-.TN - page 23

    23 ...

  • Cisco Systems PG30 G-.TN - page 24

    Via C. Colombo, 9 - 35011 Campodarsego (PD) Italy Tel. +39-049-9200944 - Fax +39-049-9200945-9201269 Internet: www.cibunigas.it - E mail: cibunigas@cibunigas.it ...

メーカー Cisco Systems カテゴリー Burner

Cisco Systems PG30 G-.TNのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PG30 G-.TNの取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems PG30 G-.TNの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems PG30 G-.TNの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems PG30 G-.TNの取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems PG30 G-.TNのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems PG30 G-.TNの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems PG30 G-.TNデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems PG30 G-.TNを使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems PG30 G-.TNユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems PG30 G-.TNの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems PG30 G-.TNの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems PG30 G-.TNに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems PG30 G-.TNデバイスの基本機能を使うにあたってのヒント。 Cisco Systems PG30 G-.TNのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems PG30 G-.TNに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems PG30 G-.TNのメーカー/サービスへの連絡先に関する情報。

Cisco Systems PG30 G-.TNについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems PG30 G-.TNの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems PG30 G-.TNで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)