Skil 3100の取扱説明書

11ページ 1.63 mb
ダウンロード

ページに移動 of 11

Summary
  • Skil 3100 - page 1

    For English V ersion V ersion française V ersión en español See page 2 V oir page 12 V er la página 12 Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad IMPOR T ANT : IMPOR T ANT : IMPOR T ANTE: Read Before Using Lire avant usage Leer antes de usar 1-877-SKIL999 (1-877-754-5999) www ...

  • Skil 3100 - page 2

    2. General Safety Rules “ READ ALL INSTRUCTIONS” Failure to follow the safety rules listed below and other basic safety precautions may result in serious personal injury. THINK SAFETY Safety is a combination of operator common sense and alertness at all times when the X-Bench is being used. W ork Area KEEP CHILDREN AWAY Do not let visitors cont ...

  • Skil 3100 - page 3

    3. Read and understand all instructions for use of X- Bench and insert plates with tools. Failure to follow all instructions listed below may result in serious personal injury. Use only with Skil accessory insert plates (jig saw, drill press, belt sander and router). The stamped rails or clamps may have sharp edges. Be careful in handling the bench ...

  • Skil 3100 - page 4

    Replace damaged cords immediately. Use of damaged cords can shock, burn or electrocute. Always use proper extension cord. If an extension cord is necessary, a cord with adequate size conductors should be used to prevent excessive voltage drop, loss of power or over- heating. The table shows the correct size to use, de- pending on cord length and na ...

  • Skil 3100 - page 5

    5. 1. Opening the X-Bench a . T he X-Bench comes in the folded position and no assembly is r equired. In order to open the X-Bench, the user must pull and twist the main knob, located by the handle, to the open position (Fig. 1a). b. After the table has been opened, the knob must be turned back into the locked position before extending the legs or ...

  • Skil 3100 - page 6

    c. Once the user sets one leg at the desired height, follow the same steps for the remaining three legs. 4. Adjustable Foot – for Leveling Bench a. If you are working in an area that is not level, we have provided a solution. We have an adjustable foot that will extend 1.75” inches to level your bench (Fig. 6). Before operating make sure the en ...

  • Skil 3100 - page 7

    7 . M ake sure X-Bench is not plugged in and m ain outlet is off. 8. Power Switch a. The female plug is located on the bottom of the switch and the m ale plug is located on the side of the switch box (Fig. 11). C onnect the switch box to an electrical outlet by using an e xtension cord. Plug the desired tool into the female plug and turn the switch ...

  • Skil 3100 - page 8

    11. Tail Vise (Sold Separately) a. Locate the following parts: (1) Clamp block (MDF), (2) Guide rods, (1) Threaded rod, (6) Bolts and (6) Bolt covers. b. Position clamp block (MDF) over guide rods, and threaded r od as shown in figure 16 c . Securely attach guide block to the rods with (6) washer and bolts provided (Fig. 16). d . Place one bolt cov ...

  • Skil 3100 - page 9

    15. Shelf and Tool Bag (Sold Separately) a. Shelf and tool bag come fully assembled. b. There are four hooks under the work bench (Fig. 23.) c. Attach the Velcro straps located on the shelf to the hooks under the table (Fig. 23). Note: Unit can fold up with shelf and bag attached. Maximum weight load is 20lbs. 13. Finishing Tray (Sold Separately) a ...

  • Skil 3100 - page 10

    10 . 15. Universal Insert Plate: a. A blank insert plate is provided with the X-Bench. This area is meant to be used only with the Skil insert plate technology which is sold separately. The insert plates which can be purchased separately are a jigsaw insert plate, sander insert plate, router insert plate and a drill press insert plate. Use only X-B ...

  • Skil 3100 - page 11

    11 . Direction of Cut Direction of Cut ...

メーカー Skil カテゴリー Saw

Skil 3100のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 3100の取扱説明書
- Skilの製品カード
- パンフレット
- またはSkil 3100の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Skil 3100の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Skil 3100の取り付け説明書、サービスマニュアル、簡易説明書、またはSkil 3100のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Skil 3100の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Skil 3100デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSkil 3100を使用するのを助ける技術的文書のことです。説明書は通常、全てのSkil 3100ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Skilの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Skil 3100の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSkil 3100の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Skil 3100に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Skil 3100デバイスの基本機能を使うにあたってのヒント。 Skil 3100のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Skil 3100に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSkil 3100のメーカー/サービスへの連絡先に関する情報。

Skil 3100についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSkil 3100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSkil 3100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)