Cub Cadet CS5018の取扱説明書

24ページ 3.39 mb
ダウンロード

ページに移動 of 24

Summary
  • Cub Cadet CS5018 - page 1

    Professional Landscaping Tools CS5018 / CS5220 18 or 20” CHAIN SA W IMPOR T ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y DO NOT THROW A W A Y ...

  • Cub Cadet CS5018 - page 2

    2 T able of Contents Content Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Know Your Unit . . . . . . . . . ...

  • Cub Cadet CS5018 - page 3

    3 • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill or under the influence of alcohol, drugs or medication. •O nly responsible individuals who are familiar with the instructions may operate the chain saw (no one under the age of 16). Provide parental supervi ...

  • Cub Cadet CS5018 - page 4

    4 Kickback Safety Precautions KICKBACK may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast r everse r eaction, kicking the guide bar up and back towards the operator . Pinching the saw chain along the top of the guide ...

  • Cub Cadet CS5018 - page 5

    5 Safety (continued) • Use caution when handling fuel. Move the chain saw at lest 10 feet (3 m) from the fueling point before starting the engine. • Do not allow other persons to be near the chain saw when starting or cutting with the chain saw. Keep bystanders and animals out of the work area. • Do not remove, damage or de-activate any of th ...

  • Cub Cadet CS5018 - page 6

    6 SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs. • WARNING - READ OPERATOR'S MANUAL Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. • ...

  • Cub Cadet CS5018 - page 7

    7 Chain Saw Components 1 - Choke lever 2 - Throttle trigger 3 - Throttle trigger lockout 4 - Carburetor adjustment scr ews 5 - Inertial brake lever 6 - Exhaust muffler 7 - Chain 8 - Guide bar 9 - Air filter cover 10 - On/off switch 11 - Fuel tank cap 12 - Starter handle 13 - Oil tank cap 14 - Primer bulb 15 - Decompression valve 16 - Lateral chain ...

  • Cub Cadet CS5018 - page 8

    8 Check the chain tension frequently when operating the chain saw . Always use protective gloves. Fitting the Bar & Chain Section 3 1 2 3 4 With the engine off, follow the ensuing instructions: • Pull the guard (Fig. 1) towards the front handle to check that the chain brake is not on. • Remove the bar nuts (A) and the chain cover (B, Fig. 2 ...

  • Cub Cadet CS5018 - page 9

    9 8 6 5 7 • Put down the chain cover, inserting it into its housing and, keeping it pressed against the bar, screw on the chain tightener screw (L, Fig. 5) so that the pawl (D, Fig. 3) goes into the hole (G, Fig. 3) of the bar. • Fit the chain cover and the relative nuts without tightening them. • Tension the chain by means of the tensioning ...

  • Cub Cadet CS5018 - page 10

    10 Oil and Fuel Section 4 10 11 Never use waste oil. Always use biodegradable lubricant (part number em-1108014) which is specific for bar and chain and also respectful towards natur e and the chain saw's parts. T wo-stroke engines have high specific horsepower and we therefor e r ecommend the use of well- known, super gasoline, without lead a ...

  • Cub Cadet CS5018 - page 11

    11 Operate this unit only in a well-ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. A void accidental starting. Make sur e you ar e in the starting position when pulling the starter rope (Fig. 13). T o avoid serious injury , the operator and unit must be in a stable position while starting. Operation Section ...

  • Cub Cadet CS5018 - page 12

    12 Operation (continued) 16 15 17 STOPPING THE ENGINE Release the throttle lever and let the engine return to idle. (B, Fig. 15). Turn off the engine, putting the ON/OFF switch (C) in the STOP position. Do not put the chain saw on the ground when the chain is still moving. BREAKING-IN THE CHAIN New chains will stretch and must be tightened frequent ...

  • Cub Cadet CS5018 - page 13

    13 Carburetor Adjustment Section 6 CARBURETOR Before adjusting the carburetor, clean the starter cover (Fig. 18), the air filter (Fig. 19) and warm up the engine. This engine is designed and manufactured in order to comply with the applicable Exhaust Emission Standards. The Exhaust Emission Control System includes the ignition system, the air inlet ...

  • Cub Cadet CS5018 - page 14

    14 21 22 23 Kickback Section 7 PRECAUTIONS AGAINST KICKBACK Kickback is a dangerous reaction that can lead to serious injury. Do not rely only on the safety devices provided with your saw. As a chain saw user, you must take special safety precautions to help keep your cutting jobs free from accident or injury. KICKBACK WARNINGS Refer to Figures 21, ...

  • Cub Cadet CS5018 - page 15

    26 28 25 27 INERTIAL CHAIN BRAKE The inertial chain brake ensures maximum safety when using the chain saw. It protects the operator from dangerous kickback which can occur during working phases. The chain brake can be actuated in two ways. First, when the operator presses the lever (Fig. 25) (manual operation) the chain consequently and instantly l ...

  • Cub Cadet CS5018 - page 16

    16 29 30 Cutting T echniques (Felling, Limbing Bucking) Section 9 31 32 OPERA TING INSTRUCTIONS Always follow the safety precautions. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vibrations and kickback vary with differ ent materials; the safety requir ements and r egulations would not be r espec ...

  • Cub Cadet CS5018 - page 17

    17 Now, make your felling cut on the opposite side of the trunk. Start the cut about 4-5 cm (2”) higher than the center of the notch (3 - Fig. 30). Always leave a hinge (A, Fig. 31 and 32) which allows you to control the direction the tree falls in. Put a wedge into the felling cut, before the tree starts to move, to prevent the chain saw guide b ...

  • Cub Cadet CS5018 - page 18

    18 37 38 Maintenance Section 10 39 Always wear protective gloves and eye pr otection during maintenance operations. Do not carry out maintenance when the engine is hot. CHAIN SHARPENING The pitch of the chain (Fig. 37) is .325”x.058”. Sharpen the chain using protective gloves and a round file of Ø 4.8 mm (3/16”). Do not fit the .325” chain ...

  • Cub Cadet CS5018 - page 19

    19 Maintenance (continued) 40 41 42 43 GUIDE BAR The guide bar has a sprocket at its base that must be lubricated with grease using a lubrication syringe (Fig. 40). Reverse the guide bar every 8 working hours to ensure uniform wear. Keep the bar groove and lubrication hole clean using the bar groove cleaner (Fig. 41). Check the bar rails frequently ...

  • Cub Cadet CS5018 - page 20

    20 46 47 49 FUEL FIL TER Check the fuel filter periodically. Replace it if it is too dirty (Fig. 45). OIL PUMP (automatic / adjustable) Flow adjustment is pre-set by the manufacturer. Oil flow can be adjusted by the operator according to specific requirements. This is accomplished by the special adjusting screw (Fig. 46). Oil flow occurs only when ...

  • Cub Cadet CS5018 - page 21

    21 51 50 Maintenance (continued) 52 53 CHAIN BRAKE Always wear safety glasses when performing maintenance on your saw . If the chain brake does not work properly, remove the bar clamp (chain cover) to inspect. Clean brake mechanism and related parts, removing woodchips, dust, excessive oil and foreign material. Use a brush or low volume compressed ...

  • Cub Cadet CS5018 - page 22

    22 ENGINE* *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle Displ ...

  • Cub Cadet CS5018 - page 23

    23 EP A Emission Control W arranty Statement Y our W arranty Rights and Obligations The Environmental Protection Agency and Cub Cadet LLC (Cub Cadet) are pleased to explain the emission control system warranty on your 2002 and later small off-road engine. New small off-road engines must be designed, built and equipped to meet stringent anti-smog st ...

  • Cub Cadet CS5018 - page 24

    MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given by ...

メーカー Cub Cadet カテゴリー Chainsaw

Cub Cadet CS5018のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CS5018の取扱説明書
- Cub Cadetの製品カード
- パンフレット
- またはCub Cadet CS5018の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cub Cadet CS5018の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cub Cadet CS5018の取り付け説明書、サービスマニュアル、簡易説明書、またはCub Cadet CS5018のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cub Cadet CS5018の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cub Cadet CS5018デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCub Cadet CS5018を使用するのを助ける技術的文書のことです。説明書は通常、全てのCub Cadet CS5018ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cub Cadetの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cub Cadet CS5018の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCub Cadet CS5018の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cub Cadet CS5018に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cub Cadet CS5018デバイスの基本機能を使うにあたってのヒント。 Cub Cadet CS5018のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cub Cadet CS5018に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCub Cadet CS5018のメーカー/サービスへの連絡先に関する情報。

Cub Cadet CS5018についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCub Cadet CS5018の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCub Cadet CS5018で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)