Behringer SHARK DSP110の取扱説明書

25ページ 1.37 mb
ダウンロード

ページに移動 of 25

Summary
  • Behringer SHARK DSP110 - page 1

    SHARK ® DSP110 Userss Manual Version 1.2 April 2001 www.behringer.com ENGLISH ...

  • Behringer SHARK DSP110 - page 2

    2 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 3

    3 SHARK DSP1 10 1. INTRODUCTION Thank you very much for expressing your confidence in BEHRINGER products by purchasing the SHARK DSP110. + This manual first describes the terminology used, so that you can fully understand the DSP110 and its functions. Please read the manual carefully and keep it for future reference. 1.1 The concept With the SHARK ...

  • Behringer SHARK DSP110 - page 4

    4 SHARK DSP1 10 Fig. 1.1: T ypical feedback loop 1. 2 Before you begin Your SHARK was carefully packed in the factory and the packaging is designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the carton and its contents for any signs of physical damage, which may have occurred during transit. + If ...

  • Behringer SHARK DSP110 - page 5

    5 SHARK DSP1 10 Be sure that there is enough air space around the unit for cooling and please do not place the SHARK on high-temperature devices such as power amps, etc. to avoid overheating. Please use the enclosed power supply to connect the unit to the mains. The supply complies with all applicable safety standards. + Please note that all units ...

  • Behringer SHARK DSP110 - page 6

    6 SHARK DSP1 10 1. 3 Control elements Fig. 1.2: Front p anel control elements of the DSP1 10 1 The CLIP LEVEL METER shows you whether or not the digital circuitry is driven correctly. Any corrections can be made with the CLIP LEVEL control . Be sure that the CLIP LED wont light up. 2 The CLIP LEVEL control lets you adapt the internal gain optima ...

  • Behringer SHARK DSP110 - page 7

    7 SHARK DSP1 10 4 The 4-digit DISPLAY reads the absolute values of the adjusted parameters. 5 The FB-D FILTER STATUS LEDs display the status of each of the 12 individual filters. The SHARK uses four different filter modes: s Disabled filters (which can be re-enabled with the ACTIVE button). When a filter is off, its LED is not lit. s Free filters w ...

  • Behringer SHARK DSP110 - page 8

    8 SHARK DSP1 10 9 The LOW CUT button lets you enter the high pass filters cut-off frequency (20 to 150 Hz). When set to OFF the filter is inoperative. The control and Hz LEDs light up while you are entering a value. Use the UP/DOWN buttons to edit. Pressing the LOW CUT button for a longer time (please wait, until all five parameter LEDs li ...

  • Behringer SHARK DSP110 - page 9

    9 SHARK DSP1 10 + When both FILTER LED and display stop flashing, the FILTER LEARN function has been completed. Press the FILTER key to cancel the function. After a short delay, the unit returns to the FILTER menu. The FILTER LEARN function generates short feedback-causing signals that are sent back to the DSP110s input, where feedbacks are dete ...

  • Behringer SHARK DSP110 - page 10

    10 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 11

    11 SHARK DSP1 10 20 This is the SHARKs balanced JACK input, which is wired in parallel to the XLR input. 21 Use the INPUT LEVEL switch to select the input sensitivity (microphone or line levels). In LINE mode, you can use the CLIP LEVEL control to adapt the internal level settings to the digital circuitry. Please make sure that the CLIP-LED will ...

  • Behringer SHARK DSP110 - page 12

    12 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 13

    13 SHARK DSP1 10 2.1.3 Connection between mixing console and power amplifier When you use the SHARK as a Delay Line unit for speaker systems placed at various positions (see chapter 2.3), you should connect the SHARK between the consoles output and the input of the power amp driving the delayed speakers. ...

  • Behringer SHARK DSP110 - page 14

    14 SHARK DSP1 10 2.1.4 The SHARK used in the monitor path Inserting the DSP110 in the monitor path of your mixing console gives you utmost protection against unwanted feedback. Monitor paths are particularly susceptible to feedback, because on stage there are usually several microphones and speakers placed close to each other. Especially vocal micr ...

  • Behringer SHARK DSP110 - page 15

    15 SHARK DSP1 10 Fig. 2.4: T wo SHARKs in the monitor path 2.1.5 The SHARK used in single channels and subgroups Whenever you want to make sure that wanted feedback such as the feedback sounds produced by a guitar wont be removed, you should insert one or several DSP110 into feedback-prone single channels (e.g. vocals) or subgroups of your ...

  • Behringer SHARK DSP110 - page 16

    16 SHARK DSP1 10 ...

  • Behringer SHARK DSP110 - page 17

    17 SHARK DSP1 10 2. 2 The Feedback Destroyer in the SHARK The SHARK identifies feedback by splitting the entire frequency spectrum (20 Hz to 20 kHz) into sections of 1/60 of an octave and determining the level of each of these bands. The values calculated are then referenced to the level of the overall signal. The resulting level difference determi ...

  • Behringer SHARK DSP110 - page 18

    18 SHARK DSP1 10 2. 3 The integrated Delay In addition to speakers on or near the stage, major-scale installations often have speaker groups positioned at a distance to the stage or flown above the audience, in order to provide listeners away from the stage with direct sound. However, since sound needs some time to travel around (343.6 m/sec at 20? ...

  • Behringer SHARK DSP110 - page 19

    19 SHARK DSP1 10 between microphones, without producing any unpleasant side effects. A typical Gate application is the processing of vocal tracks. Especially when using a Compressor, the distance between microphone and singer is critical: as the distance increases, more and more disturbing background noise is picked up. Use the Gate function to fad ...

  • Behringer SHARK DSP110 - page 20

    20 ...

  • Behringer SHARK DSP110 - page 21

    21 SHARK DSP1 10 Unbalanced use of mono 1/4" jack plugs Ring Balanced use of stereo 1/4" jack plugs Balanced use with XLR connectors 1 2 3 2 1 3 ...

  • Behringer SHARK DSP110 - page 22

    22 SHARK DSP1 10 4. SPECIFICATIONS AUDIO INPUTS Connectors XLR and 1/4" jack T ype RF filtered, servo-balanced input Impedance 6 kOhms balanced, 3 kOhms unbalanced Nominal Operating Level microphone or line level source (switchable) Max. Input Level +19 dBu at microphone level and line level AUDIO OUTPUTS Connectors XLR and 1/4" jack T yp ...

  • Behringer SHARK DSP110 - page 23

    23 SHARK DSP1 10 5. RACKMOUNT (OPTIONAL) With the available rackmount (optional) you have the possibility to place five SHARKs on two units of space in your rack. + Before you begin with the work, please disconnect the Power Supply Units from the SHARKs! To mount the SHARKs on the rackmount you should use the supplied screws (type M3). You need two ...

  • Behringer SHARK DSP110 - page 24

    24 SHARK DSP1 10 Fig. 5.1: Inst allation of the DSP1 10 on the available rackmount (optional) + Please, only use the supplied screws to install the SHARKs on the rackmount. Longer or thicker screws can damage the electronics inside of the device and doing so will void your warranty rights. You will need 2 units of space for the DSP110 rackmount. Fo ...

  • Behringer SHARK DSP110 - page 25

    25 SHARK DSP1 10 6. WARRANTY 6. WARRANTY § 1 WARRANTY CARD/ONLINE REGISTRATION To be protected by the extended warranty, the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH, in accordance with the conditions stipulated in § 3. Failure to return the card in ...

メーカー Behringer カテゴリー Power Supply

Behringer SHARK DSP110のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SHARK DSP110の取扱説明書
- Behringerの製品カード
- パンフレット
- またはBehringer SHARK DSP110の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Behringer SHARK DSP110の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Behringer SHARK DSP110の取り付け説明書、サービスマニュアル、簡易説明書、またはBehringer SHARK DSP110のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Behringer SHARK DSP110の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Behringer SHARK DSP110デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBehringer SHARK DSP110を使用するのを助ける技術的文書のことです。説明書は通常、全てのBehringer SHARK DSP110ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Behringerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Behringer SHARK DSP110の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBehringer SHARK DSP110の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Behringer SHARK DSP110に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Behringer SHARK DSP110デバイスの基本機能を使うにあたってのヒント。 Behringer SHARK DSP110のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Behringer SHARK DSP110に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBehringer SHARK DSP110のメーカー/サービスへの連絡先に関する情報。

Behringer SHARK DSP110についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBehringer SHARK DSP110の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBehringer SHARK DSP110で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)