Black Box LE072Aの取扱説明書

26ページ 0.16 mb
ダウンロード

ページに移動 of 26

Summary
  • Black Box LE072A - page 1

    CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com JULY 1996 ...

  • Black Box LE072A - page 2

    1 FCC ST A TEMENT FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to ...

  • Black Box LE072A - page 3

    2 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS Contents Chapter Page 1. Specifications ....................................................................................... 3 2. Introduction......................................................................................... 4 2.1 Available Models ....................................... ...

  • Black Box LE072A - page 4

    3 CHAPTER 1: Specifications Connectors — LE071A, LE073A: (1) RJ-45 male; LE171: (1) RJ-45 female, LE072A, LE074A: (1) BNC male; LE172: (1) BNC female; LE075A: (1) AUI male; LE175: (1) AUI female Size — 4.1"H x 2.4"W x 1"D (10.4 x 6.1 x 2.5 cm) Weight — 0.2 lb. (0.1 kg) Standards — Conforms to the IEEE 802.3 Ethernet standard. ...

  • Black Box LE072A - page 5

    4 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 2. Introduction 2.1 A vailable Models The following models of the Adapters and the Media Units are available: Modular Parallel Adapters: • LE071A: Modular Parallel Adapter w/SPC for 10BT • LE072A: Modular Parallel Adapter w/SPC for BNC • LE073A: Modular Parallel Adapter w/EPS for 10BT • L ...

  • Black Box LE072A - page 6

    5 CHAPTER 2: Introduction 2.2 Features The Adapters offer the following features: • Fits any Ethernet cable type via modular snap-on media units • Supplied with drivers for Novell ® NetWare ® (ODI™), Microsoft ® LAN Manager, 3Com ® 3+Open™ (NDIS), Artisoft LANtastic and Packet TCP/IP • Powered by the Self-Powering Cable (SPC), or any ...

  • Black Box LE072A - page 7

    6 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 3. Installation IMPOR T ANT! Make sure the computer is turned off while performing the install procedure. 3.1 Attach the Media Unit To attach the Media Unit to the Adapter, hold the Adapter with the logo facing up, press the top and bottom of the unit together, and insert it until it snaps into t ...

  • Black Box LE072A - page 8

    7 CHAPTER 3: Installation 3.2 Connect the Network Cable Connect the network cable unit as illustrated for each model below. 3.2.1 LE071A AND LE073A For the Modular Parallel Adapter w/SPC for 10BT (LE071A) and the Modular Parallel Adapter w/EPS for 10BT (LE073A), refer to Fig. 3-2 . Fig. 3-2. Connecting an Unshielded T wisted Pair Cable to the Media ...

  • Black Box LE072A - page 9

    8 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 3.2.2 LE072A AND LE074A For the Modular Parallel Adapters for BNC (LE072A and LE074A), refer to Fig. 3-3. Fig. 3-3. Connecting an RG-58/U Coaxial Cable to the Media Unit. Make sure that the RG-58A/U coaxial cable has a T-connector at the end. Then connect the T- connector to the BNC connector at ...

  • Black Box LE072A - page 10

    9 CHAPTER 3: Installation NOTE Both ends of the T- connector must be attached to network cabling. If the Adapter is at the end of a network segment, the end of the T-connector not attached to the network must have a 50-ohm terminator installed. 3.2.3 LE075A For the Modular Parallel Adapter for AUI, refer to Fig. 3-4 . After connecting the connector ...

  • Black Box LE072A - page 11

    10 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 3.3 Plug the Ethernet Adapter into the Computer Plug the 25-pin connector on your Modular Parallel Adapter into the parallel port at the back of your notebook/laptop computer, holding the Adapter with the logo at the top. Tighten the knobs on the Adapter clockwise to fasten it tightly (see Fig. ...

  • Black Box LE072A - page 12

    11 CHAPTER 3: Installation 3.5 Install the AC Power Adapter If the SPC is not used, plug the AC power adapter cable into the small round socket at the back of the Modular Media Unit, as shown in Fig. 3-6 . Plug the other end of the AC adapter cable into any standard electrical outlet. The red LED will then light up. Fig. 3-6. Installing the AC Powe ...

  • Black Box LE072A - page 13

    12 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 4. Software Setup and Operation The ODI subdirectory contains the following DOS ODI files for use with Novell NetWare and other network operating systems using the ODI specifications: • LSL.COM — The Novell Link Support Layer program • SETODI.COM — Proprietary Ethernet ODI driver • IP ...

  • Black Box LE072A - page 14

    13 • .ETHERNETPOCKET PROTOCOL.INI—Sample initialization file • .NIFSETDOS.NIF— Configuration file used by the setup program The MSLANMAN.OS2DRIVERS subdirectory contains the drivers and files for Microsoft LAN Manager OS/2 workstation. • .ETHERNETPOCKET SETNDIS.OS2—Driver for Microsoft LAN Manager OS/2 workstation • .ETHERN ...

  • Black Box LE072A - page 15

    14 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 4.2.2 C ONFIGURATION (O PTIONAL ) The SETODI is a self-configuring driver that automatically detects the correct LPT port, interrupt line, and unidirectional/bidirectional mode to be used. If you have a special configuration, you may need to override this automatic selection by using the NET.CFG ...

  • Black Box LE072A - page 16

    15 4.2.3 O PERATION To start work on the NetWare workstation, run the STARTNET batch file. Then log into the network. The STARTNET.BAT file includes the following set of commands: LSL SETODI IPXODI NETX F: If you wish, you may enter these commands in the AUTOEXEC.BAT file in the order shown. To unload the ODI workstation software, unload the progra ...

  • Black Box LE072A - page 17

    16 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 3. When prompted, insert the Network Drivers diskette. 4. Select “Modular Parallel Adapter” from the menu. 5. Continue with the installation until it is completed. 6. Reboot the PC. Installation for LAN Manager versions 2.1 and later is now complete. 4.3.2 I NSTALLATION FOR M ICROSOFT LAN M ...

  • Black Box LE072A - page 18

    17 CHAPTER 4: Software Setup and Operation The options are as follows: • POLLING—A PC may use either IRQ-7 or IRQ-5 for handling the parallel port communications. If you need to work without interrupts (usually only with test evaluations), delete the semicolon in this line. This will force the driver to operate in a polled mode without using ha ...

  • Black Box LE072A - page 19

    18 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 7. In the “Network Settings” window, choose “OK.” From the next window choose “Restart Computer.” The content of the Modular Parallel Adapter OEMSETUP.INF file is: [disks] A:=., “Modular Parallel Adapter install” [netcard] ms$sndis=“Modular Parallel Adapter”, 0, ndis, etherne ...

  • Black Box LE072A - page 20

    19 CHAPTER 4: Software Setup and Operation 4.5.2 C ONFIGURATION (O PTIONAL ) SETAILAN accepts the following standard command line switches: HELP, XEROX, IEEE, MPX, PACKET_SIZE, REMOVE, VERBOSE, “?” and “@.” In addition to the standard command line switches, SETAILAN accepts the following: UNIDIR, LPTn, EPP, and DISABLELINK 4.5.3 O PERATION ...

  • Black Box LE072A - page 21

    20 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS Hardware related switches are: UNIDIR, EPP, DISABLELINK and LPTn. The Network Drivers diskette contains the SETDIAG self-test diagnostic utility program, which tests the adapter and reports the results of the tests. CAUTION Be sure that the network driver is not loaded before you run the program ...

  • Black Box LE072A - page 22

    21 CHAPTER 5: Self-T est and Diagnostics To run the self-test and diagnostics program: 1. Copy the SETDIAG.* files from the supplied network drivers diskette into the network directory. 2. At the network directory prompt, type the following command: setdiag The “setdiag” command may be entered with special command line parameters, as follows: e ...

  • Black Box LE072A - page 23

    22 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS 5.1.1 A DVANCED RAM T EST The diagnostics portion of the SETDIAG program activates a brief RAM test. However, to thoroughly test the Adapter’s RAM, several time- consuming tests are required. The Advanced RAM Test option in the SETDIAG main menu activates those tests. Once activated, all tests ...

  • Black Box LE072A - page 24

    23 CHAPTER 6: Error Messages If problems occur during operation of your Adapter, one of the messages below will be displayed. Error messages can be recognized by the beep and the word FATAL that precedes the message. All other messages on the screen are for information only. The following is a list of common communication and driver error messages: ...

  • Black Box LE072A - page 25

    24 MODULAR P ARALLEL ADAPTERS AND MODULAR MEDIA UNITS While we trust that your Adapter will operate reliably over a long period of time, if you encounter any problems while using it, please perform the following steps before contacting Black Box. 1. Make sure that your adapter is properly installed, powered, and connected to the network. 2. Run SET ...

  • Black Box LE072A - page 26

    1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746 © Copyright 1996. Black Box Corporation. All rights reserved. ...

メーカー Black Box カテゴリー Portable Generator

Black Box LE072Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LE072Aの取扱説明書
- Black Boxの製品カード
- パンフレット
- またはBlack Box LE072Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Black Box LE072Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Black Box LE072Aの取り付け説明書、サービスマニュアル、簡易説明書、またはBlack Box LE072Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Black Box LE072Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Black Box LE072Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBlack Box LE072Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのBlack Box LE072Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Black Boxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Black Box LE072Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBlack Box LE072Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Black Box LE072Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Black Box LE072Aデバイスの基本機能を使うにあたってのヒント。 Black Box LE072Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Black Box LE072Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBlack Box LE072Aのメーカー/サービスへの連絡先に関する情報。

Black Box LE072Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBlack Box LE072Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBlack Box LE072Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)