Cub Cadet M48の取扱説明書

33ページ 3.67 mb
ダウンロード

ページに移動 of 33

Summary
  • Cub Cadet M48 - page 1

    Service Manual IMPORT ANT : READ SAFETY RUL ES AND INSTRUCTIONS CAREFULL Y PRINTED IN USA FORM NO.769-00966 This Service Manual is not a substitute for th e Operator ’s Manu al. Y ou must read, underst and and follow all of the directions in this manual as well as the Oper ator ’ s Manual before working on this power equipment. (1 1/ 2003) CUB ...

  • Cub Cadet M48 - page 2

    ...

  • Cub Cadet M48 - page 3

    TABLE OF CONTENTS M48 Tank .......................................................................................................... 1 About t his Section ............................................................................................. 1 Changes for ‘ 03 and ‘04 ..................................................................... ...

  • Cub Cadet M48 - page 4

    ...

  • Cub Cadet M48 - page 5

    M48 T ank 1 1. ABOUT THIS SECTION: The M48 is p art of the Cub Cadet Commercial T ank Series. The 2004 model year M48 is ver y similar to The 2001 model year T ank. Earlier versions of this machine have been covered in the “ 2001 Cub Cadet Commercial T echnical Handbook”: F orm #770- 10528. 2. CHANGES FOR ‘03 AND ‘04 • New hydro motor fra ...

  • Cub Cadet M48 - page 6

    M48 Tank 2 3.5. For complete br ake adjustment procedures, refer to the “Brake Adjustment” section of this manual. For the purp ose of tracking, insu re that the brake linkage bellcra nks and rods are well lubricated, not dam aged, and work as intended. See Figure 3.5. 3.6. T o check for brake drag, open the the relief valve on each hydr o pump ...

  • Cub Cadet M48 - page 7

    M48 T ank 3 3.12. If adju stment is necessary , re move the cutting deck. 3.13. Inspect the return to neutr al cylinders, rods, and bellcranks of the hydro control linkages. • The bellcranks should pivot easily without too much play . • The rods should not be bent, and the rod ends should not be loose. NOTE: The ro d end and jam nut at the rear ...

  • Cub Cadet M48 - page 8

    M48 Tank 4 3.18. If one side does not dr ive as ef fectively as the other , test the o utput of the hydro pump to deter- mine if t he problem lies in t he pump or the hydro motor . By the process of elimination, if perfor- mance is lacking, br ake drag is eliminated, adjustment is correct, and the pu mp is O.K., then the problem is the motor . Pres ...

  • Cub Cadet M48 - page 9

    M48 T ank 5 NOTE: The test can be performe d at either l ine between the pu mp and the motor . The top line on the motor is the in line from the pump when driving forwa rd. The linkage has mo re travel in forward tha n it does in re verse, so the test is most easily done on the top line of the pump, driving the pump in the forward d irection for- w ...

  • Cub Cadet M48 - page 10

    M48 Tank 6 4.23. When the fluid is between 160-210 deg. f. (71-90 deg. c.) apply full forwa rd drive pressure to the lap bar with the engine runni ng at full speed (3600 RPM) while an assista nt closes the valve to the point where pressure reaches 300 PSI (21 Bar .). See Figure 4.23. NOTE: It may be necessary to over-shoot 300 PSI slightly , then o ...

  • Cub Cadet M48 - page 11

    M48 T ank 7 5.6. Remove the nu t, washer , a nd cooling fan from the hydro pum p to be replaced, using a 9/16” wrench. See Figure 5.6. 5.7. Use a 3/8” breaker bar to move the belt ten- sioner pulley arm, slipping the belt of f of the pul- ley . See Figure 5.7. 5.8. Unhook the spring th at maintains ten sion on the arm. This will provide more fr ...

  • Cub Cadet M48 - page 12

    M48 Tank 8 5.14. Open the relief valve on the hydro pu mp that is to be tested. This will relieve any residual hydraulic pr essure. See Figure 5 .14. 5.15. Confirm that the hydrau lic pressure has been relieved by rot ating the brake drum / hub assem - bly . If the it will not rotate, confirm that the brake is released and that the brake linkage is ...

  • Cub Cadet M48 - page 13

    M48 T ank 9 5.24. Remove the handle from the relief valve using a 7/16” wrench and a 3/16” allen wren ch. 5.25. Remove the nut s fro m the carriage bolt s that hold the hydro pu mp to the hydro pump mount - ing plate. See Figure 5.25. 5.26. Carefully lower and remove the hydro pu mp. If it is to be returned to Cub Cadet, remove the yel- low plu ...

  • Cub Cadet M48 - page 14

    M48 Tank 10 5.39. Install the wheels, lowe r the T ANK to the ground, and test run it in a safe area. Make any neces- sary adjustments before installing the cutting deck. 6. REPLACING THE HYDRO MOTOR 6.1. If the cutting deck is currently on the unit, remove it. 6.2. Safely lif t and support the rear of the t ank. 6.3. Remove th e rear wheels using ...

  • Cub Cadet M48 - page 15

    M48 T ank 11 6.9. If the brake ass embly is to be transferred to the new hydro motor: remove the cotter pi n from the castle nut that holds the hub to the axle. 6.10. Loo sen, but do not rem ove the castle nut fr om the axle using a 1 1/2” socket. NOTE: It may be necessary to set the parking brake while loose ning the nut. Release the parking br ...

  • Cub Cadet M48 - page 16

    M48 Tank 12 6.16. Withdraw the hydro mo tor , along with the three motor spacer s, and place them gently on a work bench. See Figure 6.16. 6.17. If th e brake is to be rem oved, remove the clip that holds the brake arm on the splined shaft, and mark t he location of the br ake arm on the splined shaft. 6.18. Remove the brake ar m from the splined s ...

  • Cub Cadet M48 - page 17

    M48 T ank 13 6.28. Install the brake arm and clip on the new hydro motor . See Figure 6.28. 6.29. T ransfer the O ring to flare adaptor fittings from the old hydro motor to th e new hydro motor , using a 1” wrench. Inspect the fittings and O rings. If there is any do ubt about their condition, replace them. Lightly l ubr icate the O rings with oi ...

  • Cub Cadet M48 - page 18

    M48 Tank 14 7.7. Loosen the jam nu t that locks the shoulder nut in position on the brake connec tor rod using a 9/16” wrench and a 3/4” wrench. See Figu re 7.7. 7.8. Remove the ha irpin clip that secures the brake link rod to the brak e arm on the brake assembly . 7.9. Repeat on othe r side. 7.10. Disconnect the brake link r ods (left an d rig ...

  • Cub Cadet M48 - page 19

    M48 T ank 15 7.13. Confirm that the br ake bearing hub, brake han - dle, and the brake r od that connects them move freely on the front bellcrank shaf t. 7.14. Confirm the position of the brak e bearing hub: the top of the arm th at the brake rod (to the brake handle) conn ects to should line-up di rectly with the parking b rake s witch, and the br ...

  • Cub Cadet M48 - page 20

    M48 Tank 16 7.21. Release the par king brake. 7.22. The brake bracket should draw up against the frame cross member . If th is reaction is not con- sistent, tighten the shoulde r nut slightly . There should be r oughly 1 1/2” betwe en the head of the shoulder nut and the brake bracket wh en the brakes are applied. 7.23. T ighten the jam nut. 7.24 ...

  • Cub Cadet M48 - page 21

    M48 T ank 17 8.3. The deck lif t goes ha s finer increment s of adjust- ment. See Figure 8.3. 8.4. The larger , heavier d ecks have a foot a ssist pedal to help raise and lower the deck. See Figure 8.4. Figure 8.3 Figure 8.4 8.5. Heavier hardwa re connects th e deck to the hangers. See Figure 8.5. 8.6. Heavier front p ivot bar and wider front track ...

  • Cub Cadet M48 - page 22

    M48 Tank 18 8.7. The track at the rear has a lso increased. Extra brackets have been added to the frame to step the hydro moto rs out. See Figure 8.7. 8.8. T o enable the brake linkage to rea ch the reposi- tioned hydro motor , the rear brake arm assem- blies have been d oubled-up on each side. Instead of a single rear brake ar m assembly per side, ...

  • Cub Cadet M48 - page 23

    M48 T ank 19 9. OTHER TANK FEATURES 9.1. Honda Power is of fered on t he M48-HN and M54-HN. The M48-HN has a 20 H.P . Honda V - twin engine. The M54-HN has a 24 H.P . Honda V -twin. See Figure 9.1. 9.2. ROPS is of fered on the M60- KW (Kawasaki) and M60-KH (Kohler). T his is not a bolt-on option. It is integrat ed into the frame. Th e option is pri ...

  • Cub Cadet M48 - page 24

    M48 Tank 20 9.6. 1/4” incre ments on the height adjust er , wit h foot assist deck lift. See Figure 9.6. 9.7. The deck bel t release operates in a vertical plane. It can be tensioned with foot pre ssure, and the rear wheel does no t interfere with it s travel. See Figure 9.7. 9.8. Heavy duty spherical rod end s on the arms at the front of the dec ...

  • Cub Cadet M48 - page 25

    M48 T ank 21 9.10. The deck itself features revers ible caster wheel brackets. The same p art number app lies to both the left and the r ight brackets. See Figure 9.10. 9.1 1. Improved self-aligni ng pillow blocks now sus- pend the deck. See Figure 9.1 1. Figure 9.10 Figure 9.1 1 9.12. The deck support plates are larger this year , to prevent plate ...

  • Cub Cadet M48 - page 26

    M48 Tank 22 9.15. A guiding baf fle near the rear of the ope ning helps direct the clippin gs out from under the deck. See Figure 9.15. 9.16. The addition of a “Californi a Gap” at the leading edge also improves airflow , and products the internal shape of th e deck from damage if some - thing is hit hard enou gh to bend the reinforced leading ...

  • Cub Cadet M48 - page 27

    M48 T ank 23 10. KOHLER EFI Fuel injection is nothing ne w . The Wright flyer that made history ab ove the dunes at Kitty hawk, North Carolina was fuel in jected. That was a h undred years ago this past su mmer . That system was only slightly more complex than a cam-d riven Windex bottle. All diesel engines are fue l injected, though the principles ...

  • Cub Cadet M48 - page 28

    M48 Tank 24 10.5. The return lines each lead bac k to the t a nk from a tee fitting just beneath the tee fitting for the fuel feed lines. The return fuel comes from the fuel pressure regulator . NOTE: If one branch of the return line beco mes crushed, kinked, or blocked , a disproportionate amount of fuel will return the the opposite tank. • If o ...

  • Cub Cadet M48 - page 29

    M48 T ank 25 10.8. There are two lines exiting th e pressure regula- tor . One is a regulated pressure line th at feeds the fuel rail via the fuel filter . The second line is a return line. The third line is a high pressure feed from the fuel pump. See Figure 10.8. NOTE: There are two potent ial failure modes for pressure regulators. They may reduc ...

  • Cub Cadet M48 - page 30

    M48 Tank 26 10.1 1. The shrader valve can be used for checkin g fuel pressure. Fuel pressure readings obt ained at the shrader valve ca n help pin-down problems with the fuel pump or th e fuel pressure regulator . See Figure 10.1 1. 10.12. Before any service is performed on the pressur- ized portion of the fuel system, the en gine must be allowed t ...

  • Cub Cadet M48 - page 31

    M48 T ank 27 1 1.4. The fuel pressure at the injectors is held con- stant by the fuel pressure r egulator . The amount of fuel delivered to the cylinders is controlled by the length of time that th e individual fuel injectors are triggered. The length of time the injectors are triggered varies from 1.5 to 8.0 milliseconds. 1 1.5. Both injectors are ...

  • Cub Cadet M48 - page 32

    M48 Tank 28 • Do not connect a battery charger to the T ANK with the key switch turned on. • The ECU requires at least 7.0 volt s to function. • If the battery goes dead, or is disconnec ted, the adaptive memory in the ECU will be cleared. It will take 10-15 minutes of running, at normal operating tempera tures, under a variety o f loads and ...

  • Cub Cadet M48 - page 33

    M48 T ank 29 • Crank triggers are ge nerally an all-or-nothing proposition: they work perfe ctly or not at all. In extremely r are instances, a failed crankshaf t trig- ger will not keep-up with the speed of the engine. It will work at low speed, but cause intermittent ignition and inje ctor action at higher speeds. This will result in st accato ...

メーカー Cub Cadet カテゴリー Heat Pump

Cub Cadet M48のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- M48の取扱説明書
- Cub Cadetの製品カード
- パンフレット
- またはCub Cadet M48の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cub Cadet M48の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cub Cadet M48の取り付け説明書、サービスマニュアル、簡易説明書、またはCub Cadet M48のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cub Cadet M48の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cub Cadet M48デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCub Cadet M48を使用するのを助ける技術的文書のことです。説明書は通常、全てのCub Cadet M48ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cub Cadetの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cub Cadet M48の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCub Cadet M48の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cub Cadet M48に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cub Cadet M48デバイスの基本機能を使うにあたってのヒント。 Cub Cadet M48のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cub Cadet M48に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCub Cadet M48のメーカー/サービスへの連絡先に関する情報。

Cub Cadet M48についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCub Cadet M48の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCub Cadet M48で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)