Cypress CY8C24794の取扱説明書

21ページ 0.67 mb
ダウンロード

ページに移動 of 21

Summary
  • Cypress CY8C24794 - page 1

    Power Management - L ow - Cost, Two-Cell Li -Ion/Li-Pol Battery Charge r with Cell-Balancing Support November 25, 2007 Document No. 001- 17394 Rev. * B - 1 - AN2309 Author : Oleksandr Karpin Associated Project : Yes Associated Part Family : CY8C 24x23A, CY8C24794, CY8C27x4 3, CY8C29x66 T GET FREE SAMPLES HERE T H Software Version : PSoC Designer ? ...

  • Cypress CY8C24794 - page 2

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 2 - Table 1. Specifications for Two-Cell Li-Ion/Li-Pol Battery Charger with Cell-Balancing Support Item Item Value Battery Charger Parameters Built-In Battery Charger Type Two-cell Li- Ion/Li -Pol batter y charger Power Supply Voltage 10…14V Power Consumption 35 mA Battery Current Measur ...

  • Cypress CY8C24794 - page 3

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 3 -  Temperature gradient across the battery pack. Temperature mismatches of 15 degrees Celsius can cause up to 5- percent capacity differential among cells. Such a temperature gradient is relatively common in densely packed products, where multiple heat sources are located close to the ...

  • Cypress CY8C24794 - page 4

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 4 -  Cell Balancing Time : If C is the cell capacity and b V is the battery voltage, and the requirement is to eliminate the amount of imbalance (in percent) in o ne hour of balancing time, then the power dissipation on balancin g circuit P bal is : 100% b CV P bal Equation 10 For examp ...

  • Cypress CY8C24794 - page 5

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 5 - A two-cell battery charger structure with cell -balancing support is shown in Figure 3 . Similar battery charger structures are explained in detail in AN225 8 , AN2294 , and AN2267 . Note that the fuel gauge function can easily be added to this project without changing any hardware: It ...

  • Cypress CY8C24794 - page 6

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 6 - Device Schematic The schematics shown in Figure 4 on page 7 and Figure 5 on page 8 constitute a complete two-cell battery charger. A signal from the PWM goes to the RC-filter, which co nsists of resistor R4 and capacitor C4. A constant voltage signal proportional to the PWM duty cycle ...

  • Cypress CY8C24794 - page 7

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 7 - Figure 4. Two-Cell Battery Charger Schematic – CPU, Cell Balancing, and Measuring Equipment BAL2 Q1 IR LML6402 BAL1 CALIBRATION DR I VE 1 2 3 4 5 J2 ISSP/ D EBU G X R ES VCC TX TP1 BAL1 Vref P0[7] 1 P0[5] 2 P0[3] 3 P0[1] 4 P2[7] 5 P2[5] 6 P2[3] 7 P2[1] 8 SMP 9 P1[7] 10 P1[5] 11 P1[3] ...

  • Cypress CY8C24794 - page 8

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 8 - Figure 5. Two-Cell Battery Charger Schematic – Power Supply and User Interface R 30 33 1 2 J4 POW ER 12V D C PSoC C 12 0. 33u 16V IN 1 OU T 3 U2 L78L05/TO D6 BAT 54C Close to PSoC C 15 0. 1u D8 BAS16 VC C R 29 1K VC C Vbias POW ER - + C9 100u 16V C 10 0. 1u 16V + POW ER + SW 1 POW ER ...

  • Cypress CY8C24794 - page 9

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 9 - Figure 6. PSoC Internal User Module Configuration Battery Measurement To provide a correct implementation of the charge and cell - balancing algorithms, the charge current, batter y voltage and temperature must be measured accurately. These three parameters are measured as the voltage ...

  • Cypress CY8C24794 - page 10

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 10 - The voltage measurement also is performed by the INA on the corresponding resistor. The resistive dividers (R7, R6), (R13, R12), and (R18, R19) transform cell voltage into signals suitable for the PSoC device. It is ver y important to use the high precision resistors in the resistive ...

  • Cypress CY8C24794 - page 11

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 11 - Figure 7. Temperature Profile T HOT_STOP T HOT_RESTART T COLD_STOP T COLD_RESTART T BATT Charge in process Charge in Process No Charge T DISCH_COLD_STOP T DISCH_HOT_STOP No Discharge No Discharge Two-Cell Battery Charger Fir mware The two-cell battery charger firmware is separated int ...

  • Cypress CY8C24794 - page 12

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 12 - Figure 8. Two-Cell Battery Charger State Diagram Activation Initialization Rapid Error Charge Complete Wait For Temperature Full Discharge Discharge 1 7 4 5 8 3 2 12 11 9 10 6 13 Initially the charger is in the In itialization state. After some device prepar ation, the charger goes to ...

  • Cypress CY8C24794 - page 13

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 13 - Figure 9. Two-Cell Battery Charger Firmware Flowchart Part 1 Start Init Device Measure V b1 , V b2 , I ch , T b Calc V bmin , V bmax State Activation Set I reg =I ACT ; Regulate State Initialization Yes Set Activation State Charge On Start t ACT , t CH , Timing Open LOAD Out Yes No Ch ...

  • Cypress CY8C24794 - page 14

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 14 - Figure 10 . Two-Cell Battery Charger Firmware Flowchart Part 2 State Charge Complete Charge Off Timers Off Yes No State Error Yes Charge Off Timers Off Check Charge Restart Condition Set Initialization State Yes No State Wait For Temperature Charge Off Timers Off Yes No True Yes No St ...

  • Cypress CY8C24794 - page 15

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 15 - The minimum cell-balance parameter consists of the voltage measure error value plus the internal impedance error value. The cell-balancing algorithm that is implemented here does not significantly lengthen the charge time. The c harger monitors all of the cell voltages. Cell balancing ...

  • Cypress CY8C24794 - page 16

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 16 - Two-Cell Battery Charger Par ameters All two-cell battery charger parameters are located in the header file globdefs.h in th e project folder. The header file globdefs.h contains the following parameters: Table 2. Two-Cell Battery Charger Parameters Parameter Unit Description Charging ...

  • Cypress CY8C24794 - page 17

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 17 - Cell-Balancing Paramet ers All cell-balanci ng parameters are located in the header file globdefs.h in the project folder. T he header file globdefs.h contains the following parameters: Table 3. Cell-Balancing Parameters Parameter Unit Description Vmeas_err V Resistor Matrix Error for ...

  • Cypress CY8C24794 - page 18

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 18 - Appendix Charge/Discharge and Cell -Balancing Profile Examples Figure 13 . Charge/Discharge Manager Profile Constant Current Charge Constant Voltage Charge Battery Discharge Cell Voltages Without Charge Interrupt Charger State Cell-Balancing State Charge /Discharge Current Thermistor ...

  • Cypress CY8C24794 - page 19

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 19 - Figure 14 . Cell-Balancing Activity Profile Voltage Imbalance Value Cell Voltages With Charge Interrupt [+] Feedback ...

  • Cypress CY8C24794 - page 20

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 20 - Figure 15 . Cell-Balancing Parameter Profile Screen About the Author Name: Oleksandr Karpin Title: Application Engineer Background: Oleksandr received a PhD ’s degree in com puter science in 2008 from Lviv Polytechnic National Universit y (Ukraine). His intere sts include embedded s ...

  • Cypress CY8C24794 - page 21

    AN2309 November 25, 2007 Document No. 001- 17394 Rev. * B - 21 - Document History Document Title: Power Management - Low-Cost, Two-Cell Li-Ion/Li-Pol Battery Charger with Cell-Balancing Support Document Number: 001-17394 Rev. ECN Orig. of Change Submission Date Description of change ** 1352043 HMT 08/29/2007 Obtain spec. # for note to be added to s ...

メーカー Cypress カテゴリー Battery Charger

Cypress CY8C24794のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CY8C24794の取扱説明書
- Cypressの製品カード
- パンフレット
- またはCypress CY8C24794の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cypress CY8C24794の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cypress CY8C24794の取り付け説明書、サービスマニュアル、簡易説明書、またはCypress CY8C24794のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cypress CY8C24794の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cypress CY8C24794デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCypress CY8C24794を使用するのを助ける技術的文書のことです。説明書は通常、全てのCypress CY8C24794ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cypressの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cypress CY8C24794の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCypress CY8C24794の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cypress CY8C24794に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cypress CY8C24794デバイスの基本機能を使うにあたってのヒント。 Cypress CY8C24794のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cypress CY8C24794に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCypress CY8C24794のメーカー/サービスへの連絡先に関する情報。

Cypress CY8C24794についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCypress CY8C24794の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCypress CY8C24794で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)