Audiovox 1181292の取扱説明書

12ページ 1.24 mb
ダウンロード

ページに移動 of 12

Summary
  • Audiovox 1181292 - page 1

    INSTALLATION INSTRUCTIONS FOR 50 - 0210F - 002 SERIES 1181291 50 - 0210F - 003 SERIES 1181292 50 - 0210F - 004 SERIES 1181293 SUBURBAN OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business. Special tools and equipment, as well as specializ ...

  • Audiovox 1181292 - page 2

    2 MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 SCREW, # 8 X 3/4" HWH ,TEK,Z1 4 2 SCREW, # 8 X 2 1/2" PFH ,ZII 3 3 SCREW, # 8 X 1 1/4" PWH ,BZ 4 4 CONSOLE 1 5 MOUNTING BRACKET 1 6 REAR LIGHT 1 7 REAR LIGHT TRIM 1 8 PLYWOOD, 3/8" X 6" X 14" 1 9 SCREW, # 6 X 1/2" 10 10 SCREW, 6 - 32 X 3/4" 6 11 WA ...

  • Audiovox 1181292 - page 3

    3 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. compartment console currently mounted to inner roof of v ehicle. Remove (1) one # 8 X 1 3/4" screw from recess in front of console near rear view mirror. Pull front of O.E.M. console down to access wiring. Disconnect all wiring from console. Pull console forward to release rear retainer ...

  • Audiovox 1181292 - page 4

    4 3. Discard trim ring. See Figure 3. Using a razor knife, carefully trim the (10) ten plastic pins flush with the shoulder. See Figure 4. FIGURE 3 FIGURE 4 ...

  • Audiovox 1181292 - page 5

    5 4. Remove OEM dome light and rear air conditioning control head. Disconnect wiring and set control head aside in a safe place. Remove the OEM ground screw near the center dome light assembly if applicable. See Figure 5. 5. Cut the headliner material between dome light opening and the front openings for OEM pod retainer arms. Caution: Before cutti ...

  • Audiovox 1181292 - page 6

    6 6. Install the rear mounting bracket (item 5 pg 2 ) in the O.E.M. dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. 7. Secure bracket to sheetmetal fram ...

  • Audiovox 1181292 - page 7

    7 8. If vehicle is equipped with an electronic compass, unsnap the wire harness clip and relocate toward center of vehicle. See Fig ure 9. 9. Remove and retain the two ( 2 ) door scuff plates on driver’s side. See Fig. 10. FIGURE 9 FIGURE 10 ...

  • Audiovox 1181292 - page 8

    8 10. Remove and retain the handle which mounts to top of the “B” pillar. 11. Unsnap the cover from upper and lower mo unting bracket for seat belt. Remove and retain TORX head bolt and bracket. Carefully pull panel away from side of vehicle. Unsnap upper door trim from headliner and lay aside. See Figure 11. 12. Measure 7” from rear A/C cont ...

  • Audiovox 1181292 - page 9

    9 14. Route all accessory wiring, video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams.For Suburban applications, the sugge sted routing of the video system cable is as follows: • Above headliner from video system to B - pilla ...

  • Audiovox 1181292 - page 10

    10 II. PREPARATION OF CONSOLE FOR INSTALLATION 1. Position the O.E.M. console in the front recess area of the new console (item 4 pg 2 ). Carefully fit the two together, aligning the rear compartment hinge arms through the slots in the recess pocket area. See figure 14. 2. Secure the O.E.M. compartment assembly into the console recess using (10) te ...

  • Audiovox 1181292 - page 11

    11 IV. INSTALLATION OF OVERHEAD CONSOLE. Caution: Do not overtighten screws. Use extra support for the console until secured to the vehicle. Failure to do so may cause damage to console or installed components. 1. Cons truct a jumper harness that will connect the vehicle’s dome light wires to the lights in the console and video system. Connect th ...

  • Audiovox 1181292 - page 12

    12 7. Release video screen from locked position. Lower video screen to viewing position for a ccess to mounting locations in top of video system housing. 8. Raise video system into approximate position and connect all wiring to components. Route video cable through hole in mounting bracket. Connect wiring and cabling to video system per instruction ...

メーカー Audiovox カテゴリー Car Video System

Audiovox 1181292のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1181292の取扱説明書
- Audiovoxの製品カード
- パンフレット
- またはAudiovox 1181292の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Audiovox 1181292の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Audiovox 1181292の取り付け説明書、サービスマニュアル、簡易説明書、またはAudiovox 1181292のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Audiovox 1181292の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Audiovox 1181292デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAudiovox 1181292を使用するのを助ける技術的文書のことです。説明書は通常、全てのAudiovox 1181292ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Audiovoxの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Audiovox 1181292の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAudiovox 1181292の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Audiovox 1181292に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Audiovox 1181292デバイスの基本機能を使うにあたってのヒント。 Audiovox 1181292のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Audiovox 1181292に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAudiovox 1181292のメーカー/サービスへの連絡先に関する情報。

Audiovox 1181292についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAudiovox 1181292の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiovox 1181292で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)