-
Bunn Ultra 2 - page 1
UL TRA-1 UL TRA-2 INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O- ...
-
Bunn Ultra 2 - page 2
2 40563 041108 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years part ...
-
Bunn Ultra 2 - page 3
3 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. CONTENTS Introduction & Warranty ................................................................................................ 3 Site Preparation, Electrical Requirem ...
-
Bunn Ultra 2 - page 4
4 INITIAL SETUP CAUTION – The dispenser is ver y heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 3. Remove the rear plastic plug from the trim strip between the ho pp er dr ip tr ay s an d loo sen th e auger motor cover screws. 2. Remove all shipping material, including the compressor support eye ...
-
Bunn Ultra 2 - page 5
5 11. Thoroughly rinse the hoppers an d ins tal l th em over the auge rs and cooling drums. 15. Set the lid(s) on the hopper(s). Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cord(s). 17. Assemble the drip tray . INITIAL SETUP (CONT .) 12. Slide the hopper(s) into place and push down until the hop - per lock pl ...
-
Bunn Ultra 2 - page 6
6 P3678 Set Consistency This function allows the operator to adjust the ice consistency , or torque of each auger when answered YES (“ICE”). T wo screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (UL TRA) to a maximum of 16 (ICE). Factor y default is 10. SET THICKNESS ? NO YES MIN LEFT 9 MAX MIN R ...
-
Bunn Ultra 2 - page 7
7 Set Time and Date Selecting YES (ICE) allows the operator to set the DA TE (YY MM DD) and TIME (HR MIN SEC) for display on the Home Screen. SET DA TE TIME ? NO Y E S YEAR 2005 (-) NEXT (+) MONTH 1 (-) NEXT (+) MONTH DA Y 25 (-) NEXT (+) HOUR 10 AM (-) NEXT (+) MINUTE 45 (-) NEXT (+) SECOND 30 (-) NEXT (+) Install Date The following three screens ...
-
Bunn Ultra 2 - page 8
8 OPERA TING CONTROLS UL TRA-1 There are three of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2. ...
-
Bunn Ultra 2 - page 9
9 OPERA TING CONTROLS UL TRA-2 There are five of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2. ...
-
Bunn Ultra 2 - page 10
10 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper . 2. Place the pre-mixed liquid product in the selected hopper . 3. a. Press and release the (ON/OFF) switch to power on the dispenser . b. Press and release the appropriate (ON/OFF) switch to start the Auge ...
-
Bunn Ultra 2 - page 11
11 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER • Whetherliquidconcentrateorgranulatedpowder ,allproductmustbethoroughlymixedBEFOREaddingit to the hoppers. • Forbestresultswithgranita-typeproducts,useonlyproductswithan apparentbrixof12orhigher .So ...
-
Bunn Ultra 2 - page 12
12 10. Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solu- tion. Use a clean, soft bristle brush as needed for the smaller components and tight areas. Do not immerse hopper lids. ...
-
Bunn Ultra 2 - page 13
13 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Ali gn the auge r sha ft( s) with the auger(s). Push the auger(s) as far as they will go and rotate so the flat face of the auger shaft is aligned with the flat face of the auger nose. 4. Thorou ghly rinse the hopper ...
-
Bunn Ultra 2 - page 14
14 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 32162.0000 (UL TRA-2) 00986.0002 CHARGE T ype R404A, Amount 9.5 oz (269 gm) Design Pressures: High 215 psi (15 bar) (1. ...
Bunn Ultra 2についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもBunn Ultra 2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn Ultra 2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。