Bunn SNG033000の取扱説明書

37ページ 4.82 mb
ダウンロード

ページに移動 of 37

Summary
  • Bunn SNG033000 - page 1

    SINGLE ® TF DBC ® W/SMAR T FUNNEL ® DUAL ® TF DBC ® W/SMAR T FUNNEL ® S/N DUAL068000 & UP PR OGRAMMING MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 41342.0000B 10/11 ©2008 Bunn-O-Matic Corporation S/N SNG0033000 & UP ...

  • Bunn SNG033000 - page 2

    Page 2 41342 102611 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 year ...

  • Bunn SNG033000 - page 3

    Page 3 T ABLE OF CONTENTS Glossary ......................................................................................................................................4 PROGRAMMING ........................................................................................................................5 Programming Switches ........................ ...

  • Bunn SNG033000 - page 4

    Page 4 GLOSSAR Y AD CARD: An assembly consisting of computer chips and an instruction label. Used for loading advertising messages into the brewer . BREW LOCKOUT : The inability to initiate a brew if the water temperature is less than the ready temperature programmed into the brewer . BYP ASS: The process of diverting a portion of the brew water to ...

  • Bunn SNG033000 - page 5

    Page 5 PROGRAMMING Using the menu-driven di splay on the front of the brewer , the operator h as the ability to alter or modify various brewing parameters such as brew temperatures, brew volumes, bypass percentages, etc. This allows for the precise brewing of various flavors of coffee. Programming of the brewer is achieved by entering a certain fu ...

  • Bunn SNG033000 - page 6

    Page 6 MAIN SCREEN This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water in the tank reaches the correct set temperature, the display will change from HEA TING to READY TO BREW . PROGRAMMING LOCKOUT SWITCH (mounted on main control board) This switch can be set to prevent ac ...

  • Bunn SNG033000 - page 7

    Page 7 PROGRAMMING THE BREWER (cont.) PROGRAM FUNCTIONS - LEVEL 2 There are three methods of programming the vari- ous brewing parameters of the SINGLE TF and DUAL TF with Smart Funnel Brewers. METHOD 1: Using a Smart Funnel and a G9-2T DBC or MHG Grinder: Certain coffee NAMES are stored in the G9-2T DBC or MHG's memory . When a particular nam ...

  • Bunn SNG033000 - page 8

    Page 8 PROGRAMMING THE BREWER (cont.) 41342 101911 Cycles thru right side program constants LEVEL 1 Press upper right hidden switch for approximately 2 seconds, until the following screen appears. LEVEL 2 Press upper right hidden switch for approximately 4 seconds, until “UNITS” appears on screen. Returns to normal operating mode BREW LOCK OUT? ...

  • Bunn SNG033000 - page 9

    Page 9 PROGRAM FLOW DIAGRAM (Cont.) PROGRAMMING THE BREWER (cont.) % BYP ASS XX (-) DONE (+) 3 BA TCHES DONE? NO YES SET PULSE BREW NO YES 3 BA TCHES DONE? NO YES DRIP TIME X.XX (-) DONE (+) NO-NAME LEFT SETUP COMPLETE Continue to (B) (C) EASY PULSE SETUP NO YES ENTER TIMES NO YES BREW TIME: X:XX (-) DONE (+) 3 BA TCHES DONE? NO YES NO-NAME RIGHT S ...

  • Bunn SNG033000 - page 10

    Page 10 PROGRAM FLOW DIAGRAM (Cont.) PROGRAMMING THE BREWER (cont.) L BYPS OZ/M XX.X (-) DONE (+) R BYPS OZ/M XX.X (-) DONE (+) CALIBRA TE FLOW? NO YES BREW COUNTERS? NO YES FUNNEL DETECT? NO DONE YES SERVICE TOOLS? NO YES SEL BREWER TYPE? NO YES (F) FINISHED, returns to main screen LEFT 0 NEXT RESET RIGHT 0 NEXT RESET L+R 0 NEXT RESET L+R 0 NEXT T ...

  • Bunn SNG033000 - page 11

    Page 11 UNITS METRIC DONE ENG CHANGING UNITS WILL!! ERASE!! ALL PREVIOUSL Y ST ORED RECIPES AND ALL SETUP INFO WIL BE LOST! ARE Y OU SURE? YES NO SELECTS METRIC AS THE UNIT OF MEASURE REPLACE EXIT SELECTS ENGLISH AS THE UNIT OF MEASURE UNITS (SETTING UNITS OF MEASURE) This function allows the units of measure to be set in English or Metric readings ...

  • Bunn SNG033000 - page 12

    Page 12 ENABLE ENERGYSA VR This function allows the operator to enable the ENERGY SA VINGS mode function and set the idle time. Once the set idle time has expired, the operator can choose to have the heaters either turn off, or reduce the tank holding temp to 140° F (60° C). Procedure to enable energy savings mode: Range: 0.5 to 24.0 hrs If enabl ...

  • Bunn SNG033000 - page 13

    Page 13 MUST GRIND INT O FUNNEL FIRST (COFFEE NAME) SETUP COMPLETE BEGIN SETUP OF (COFFEE NAME) QUIT SETUP? YES USE LEFT SIDE ONL Y INSERT FUNNEL WITH NEW NAME REVIEW RECIPES? NO YES (COFFEE NAME) NO YES 3 BA TCHES DONE? NO YES SET NEW RECIPE? NO YES 2 SEC. CYCLES THROUGH THREE SCREENS 2 SEC. FUNNEL CONT AINS NAME FUNNEL CONT AINS NO NAME SETUP BRE ...

  • Bunn SNG033000 - page 14

    Page 14 PROGRAMMING THE BREWER (cont.) SET NEW RECIPE (cont.) 8. Using (-) and (+) , set the amount of brew water , in ounces, to be dispensed for that particular batch size. 9. When finished, press another batch size and re- peat step 8 for that size. Continue setting all batch sizes. 10. When finished setting all batch sizes, press and release ...

  • Bunn SNG033000 - page 15

    Page 15 SET NEW RECIPE Using a RECIPE CARD to load coffee names and brew settings into the SINGLE TF DBC or DUAL TF DBC with Smart Funnel: The G9-2T DBC or MHG's memory contains certain coffee names. If the operator uses a coffee name that is not already stored in the grinder's memory , a RECIPE CARD can be obtained from the factory . The ...

  • Bunn SNG033000 - page 16

    Page 16 PROGRAMMING THE BREWER (cont.) DUAL BREWERS SET NEW RECIPE: If not using a Smart Funnel (with a computer chip) and/or a G9-2T DBC or MHG Grinder , the brewer will function as a standard Bunn SINGLE TF/DUAL TF Brewer: It is possible to operate the brewer without using a Smart Funnel and/or a G9-2T DBC or MHG Grinder . If a standard funnel, o ...

  • Bunn SNG033000 - page 17

    Page 17 PROGRAMMING THE BREWER (cont.) REVIEW RECIPES/MODIFY RECIPES/SET UP NO NAME COFFEE F A VORS: This function has three parts. It allows the operator to view the brew settings for the various coffee names programmed into the brewer . It also allows the operator to modify (change) any of the BREW VOLUMES, BYP ASS PERCENT AGES, PULSE BREW TIMES, ...

  • Bunn SNG033000 - page 18

    Page 18 PROGRAMMING THE BREWER (cont.) BREW OZ (SETTING OR ADJUSTING BREW VOL- UMES) This function allows adjustment of the brew vol- umes for each batch. The indicator signifies volume in ounces per batch. Procedure for modifying recipes - brew ounces: Range: 10.0 oz to 400 oz for all three batch sizes 1. Press and hold upper right hidden switch ...

  • Bunn SNG033000 - page 19

    Page 19 PROGRAMMING THE BREWER (cont.) % BYP ASS This function allows adjustment of the amount of water that bypasses the grounds. The number signi- fies the percentage of the brew volume which does not flow over the coffee grounds. Modifying recipes - bypass percentages: Range: 0% to 90% for all three batch sizes NOTE: If the brewer is already i ...

  • Bunn SNG033000 - page 20

    Page 20 SET PULSE BREW: This function allows the operator to program the brewer to "pulse” the sprayhead flow on and off during a brew cycle (start and stop the flow of water out of the sprayhead). This feature allows the ability to “fine-tune” the brewer for specific flavor profiles. Pulse brewing can be set up for any and all bat ...

  • Bunn SNG033000 - page 21

    Page 21 SET PULSE BREW (cont.) PROGRAMMING THE BREWER (cont.) REVIEW RECIPES? NO YES EXIT TO NEXT FUNCTION SCREEN NO-NAME LEFT MODIFY SHOW NEXT NO-NAME MODIFY SHOW NEXT DUAL BREWERS SINGLE BREWERS SEE PULSE BREW SETUP- (ENTER TIMES) (RECIPE NAME) MODIFY SHOW NEXT THA T W AS THE LAST RECIPE WHEN THE LAST COFFEE NAME IN BREWER'S MEMORY IS DISPLA ...

  • Bunn SNG033000 - page 22

    Page 22 PROGRAMMING THE BREWER (cont.) SET PULSE BREW - EASY PULSE SETUP NOTE: The procedure to enter the PULSE BREW function must be performed prior to following the steps listed below . 1. The display should read BREW TIME: X.XX and a batch size indicator will be flashing. 2. Using (-) and (+), set the desired brew time for the selected batch si ...

  • Bunn SNG033000 - page 23

    Page 23 PROGRAMMING THE BREWER (cont.) SET PULSE BREW - ENTER TIMES NOTE: The procedure to enter the PULSE BREW function must be performed prior to following the steps listed below . 1. Press and release YES . The display should now read EASY PULSE SETUP . 2. Press and release NO . The display will read ENTER TIMES? 3. Press YES to proceed. The dis ...

  • Bunn SNG033000 - page 24

    Page 24 PROGRAMMING THE BREWER (cont.) SET PREINFUSION: This function sets the brewer to turn the sprayhead flow on for a preset time (1st ON TIME) followed by a preset spray pause (OFF TIMES) and then turn the spray on continuously until the brew volume is completed. This is a special case of pulse brew. It is not pos- sible to set a batch size t ...

  • Bunn SNG033000 - page 25

    Page 25 PROGRAMMING THE BREWER (cont.) DRIP TIME (now displayed on "non" funnel lock units as well) This function allows the setting or modification of the funnel locks to stay engaged after the end of a brew cycle. This ensures the funnel cannot be removed until after the liquid has emptied out of the funnel. Procedure to modify drip ti ...

  • Bunn SNG033000 - page 26

    Page 26 PROGRAMMING THE BREWER (cont.) COPY SETTINGS (NO NAME COFFEE SETTINGS ONL Y) This function is used on DUAL brewers only to transfer all the brew settings from a NO NAME coffee flavor programmed on one side of the brewer to the other side. A NO NAME coffee is a flavor that is not in the grinder's memory or is what appears if a Smart F ...

  • Bunn SNG033000 - page 27

    Page 27 PROGRAMMING THE BREWER (cont.) 2. Press YES in this screen. The display should read LEFT ->->-> RIGHT . 3. If the initial programming was done on the left side of the brewer , press YES . The display will read ARE YOU SURE? 4. If you are sure that the data should be transferred from left to right, press YES . The display will then ...

  • Bunn SNG033000 - page 28

    Page 28 PROGRAMMING THE BREWER (cont.) REFILL - Range: 20 to 230 This function allows the operator to adjust the sensitivity of the refill circuit. This is mainly a trouble- shooting feature. Water in different geographical loca- tions can have different conductivities. By adjusting the sensitivity of the refill circuit, this will allow the brewe ...

  • Bunn SNG033000 - page 29

    Page 29 PROGRAMMING THE BREWER (cont.) SPRA Y OZ/M (DUAL BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the sprayhead. This is NOT used to change the actual flow rate, but to tell the internal controller how fast the water is flowing. The unit of measure is ounces per minute (Oz/M). Procedure to ...

  • Bunn SNG033000 - page 30

    Page 30 PROGRAMMING THE BREWER (cont.) BYP ASS OZ/M (SINGLE BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the bypass nozzle. This is NOT used to change the actual flow rate, but to tell the internal controller how fast the water is flowing. The unit of measure is ounces per minute. Procedure to ...

  • Bunn SNG033000 - page 31

    Page 31 CALIBRA TE FLOW This function allows the operator to enter the actual flow rate of the sprayhead and the bypass (for each side on DUAL brewers) by dispensing both separately for one minute. The volumes are then entered in ounces per minute (OZ/M). Procedures to calibrate the sprayhead flow rate: 1. Place a container , accurately graduated ...

  • Bunn SNG033000 - page 32

    Page 32 PROGRAMMING THE BREWER (cont.) CALIBRA TE FLOW (cont.) Procedures to calibrate the bypass flow rate: 1. Place a container , accurately graduated in ounces, and with a minimum capacity of 60 ounces, below the funnel on the brewer to be calibrated. 2. Press and hold the upper right hidden switch until the display reads UNITS . Release the sw ...

  • Bunn SNG033000 - page 33

    Page 33 PROGRAMMING THE BREWER (cont.) BREW COUNTERS This function allows the operator to track the number of brew cycles completed. The number of brew cycles on the left side, the right side, and the total of both combined can be tracked on DUAL brewers. There is one resettable counter , and one life counter that is not resettable for SINGLE brewe ...

  • Bunn SNG033000 - page 34

    Page 34 PROGRAMMING THE BREWER (cont.) Procedure to test components (outputs): 1. Place brew funnels into rails on both sides of brewer . 2. Place a server beneath each brew funnel. 3. Press and hold the upper right hidden switch until display reads UNITS. Release the switch. Continue to press and release switch until SERVICE TOOLS appears. 4. Pres ...

  • Bunn SNG033000 - page 35

    Page 35 PROGRAMMING THE BREWER (cont.) SERVICE TOOLS (cont.) NOTE: T o bypass testing any component, press NEXT to advance to the next one, without testing the previ- ous component. 10. T o test LEFT BYPASS , press ON . If the bypass valve is functional, water should run from the left brew bypass. 11. Press OFF to end flow of water . 12. Press NEX ...

  • Bunn SNG033000 - page 36

    Page 36 TEST OUTPUTS? NO YES SER VICE T OOLS? NO YES LEFT BREW V AL VE ON NEXT OFF LEFT BYP ASS ON NEXT OFF LEFT FUNNEL LOCK ON NEXT OFF RIGHT BREW V AL VE ON NEXT OFF RIGHT BYP ASS ON NEXT OFF RIGHT FUNEL LOCK ON NEXT OFF REFILL V AL VE ON NEXT OFF T ANK HEA TRS ON NEXT OFF HEA TER CONT A CT OR ON NEXT OFF BREW V AL VE ON NEXT OFF BYP ASS ON NEXT ...

  • Bunn SNG033000 - page 37

    Page 37 SERVICE TOOLS (cont.) PROGRAMMING THE BREWER (cont.) the next function screen. Press YES to run tests on various components and outputs within the brewer . 5. The display should read TEST OUTPUTS?. 6. In TEST OUTPUTS screen, press NO . Continue to press and release NO until the display reads TEST FREQUENCY?. 7. Press and release YES . The d ...

メーカー Bunn カテゴリー Coffeemaker

Bunn SNG033000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SNG033000の取扱説明書
- Bunnの製品カード
- パンフレット
- またはBunn SNG033000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bunn SNG033000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bunn SNG033000の取り付け説明書、サービスマニュアル、簡易説明書、またはBunn SNG033000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bunn SNG033000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bunn SNG033000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBunn SNG033000を使用するのを助ける技術的文書のことです。説明書は通常、全てのBunn SNG033000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bunnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bunn SNG033000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBunn SNG033000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bunn SNG033000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bunn SNG033000デバイスの基本機能を使うにあたってのヒント。 Bunn SNG033000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bunn SNG033000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBunn SNG033000のメーカー/サービスへの連絡先に関する情報。

Bunn SNG033000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBunn SNG033000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBunn SNG033000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)