ADTRAN NetVanta 1224Rの取扱説明書

13ページ 4.79 mb
ダウンロード

ページに移動 of 13

Summary
  • ADTRAN NetVanta 1224R - page 1

    TECHNICAL SUPPORT NOTE Using the GUI to Configure a N etVanta 1224R/STR fo r Internet Access using an Ethernet Port (Cable or DSL modem) Featuring ADTRAN OS and the Web GUI _____________________________________________________________________________________ Introduction This Technical Support Note shows how to conf igure the NetVanta 1224R/STR for ...

  • ADTRAN NetVanta 1224R - page 2

    Step 2 – Setting up the Private VLAN Interface Click the “VLANs” link to setup the IP addresses for the unit. In the following diagrams, we will change the default IP address to 192.168.1.254. Note: When you submit the default IP address change, you will need to change your workstation IP address to match up with the new subnet and reconnect ...

  • ADTRAN NetVanta 1224R - page 3

    Change the IP address to 192.168.1.254. After changing the default VLAN interface IP address, be sure to change your workstation IP address to match this network. For example, you could use 192.168.1.1 as your workstation IP address with a default gateway of 192.168.1.254. ...

  • ADTRAN NetVanta 1224R - page 4

    Step 3 – Add a New VLAN for the Public Subnet (Port) The public VLAN will be configured in one of three different m odes, (A) IP Routing with a Static IP, (B) IP Routing using DHCP, or (C) PPPoE. DHCP is normally used when connected to a cable modem and PPPoE is often used when connected to a DSL m odem set in pass-through or bridge mode. The fol ...

  • ADTRAN NetVanta 1224R - page 5

    (Option A) – IP Routing with a Static IP Configuration. The IP address 100.100.100.2 is used as an example. The IP address information should have been provided to you by your Internet Service Provider (ISP). ...

  • ADTRAN NetVanta 1224R - page 6

    (Option B) – IP Routing Using DHCP. This is a typical cable modem setup. ...

  • ADTRAN NetVanta 1224R - page 7

    (Option C) – PPPoE (ADSL modem set to pass-through m ode) Set the Interface Mode to PPPoE and click “Apply”. Clicking “Apply” will open a new page to set PPPoE specific settings. ...

  • ADTRAN NetVanta 1224R - page 8

    (Option C) – PPPoE specific settings A username and password are required for PPPoE. Service Name and AC Nam e are rarely used but should be entered if provided by the ISP. P eer Authentication type should almost always be set to “None”. Also, PPPoE should be set for “Negotiated” IP address unless the ISP has specified a static IP address ...

  • ADTRAN NetVanta 1224R - page 9

    Step 4 – Adding a Default Route when using a Static IP Address This step is not required when learning a default route dynamically as in step 3 (option B) when we used DHCP. You need to add a static default route when using IP Routing with a static IP address or PPPoE with a static IP address. Click the “Route Table” link and then add a stati ...

  • ADTRAN NetVanta 1224R - page 10

    Step 5 – Assign an Ethernet Port to be a member of the Public VLAN In the example below, we are setting the first Ethernet port as a mem ber of VLAN 100 and setting it to “edgeport” mode to allow this port to come up im mediately. This port should be plugged into your Internet connection. Make sure your workstation is not plugged into this po ...

  • ADTRAN NetVanta 1224R - page 11

    Step 6-1. The first wizard page is just a warning that this will overwrite any previous firewall settings. Step 6-2. Select the public VLAN interface. In our example, this is VLAN 100. ...

  • ADTRAN NetVanta 1224R - page 12

    Step 6-3. This step will allow you to setup some basic port forwarding. Port forwarding can be done at a later date by adding policies to the “Public” Security Zone. Step 6-4. The final step is to confirm that the default VLAN 1 will share the IP address applied to the public VLAN 100. ...

  • ADTRAN NetVanta 1224R - page 13

    Step 7 – Save Your Changes The basic configuration should be complete after using the Firewall Wizard. Be sure to click “Save” after you make any configuration changes. This will ensure that the configuration will be maintained in the unit by storing it in the NVRAM. Step 8 – Consult Additional Documentation Additional Documentation is avai ...

メーカー ADTRAN カテゴリー Switch

ADTRAN NetVanta 1224Rのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- NetVanta 1224Rの取扱説明書
- ADTRANの製品カード
- パンフレット
- またはADTRAN NetVanta 1224Rの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、ADTRAN NetVanta 1224Rの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、ADTRAN NetVanta 1224Rの取り付け説明書、サービスマニュアル、簡易説明書、またはADTRAN NetVanta 1224Rのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、ADTRAN NetVanta 1224Rの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

ADTRAN NetVanta 1224Rデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがADTRAN NetVanta 1224Rを使用するのを助ける技術的文書のことです。説明書は通常、全てのADTRAN NetVanta 1224Rユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

ADTRANの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. ADTRAN NetVanta 1224Rの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははADTRAN NetVanta 1224Rの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。ADTRAN NetVanta 1224Rに関してこのドキュメントで見つけることができる全てのヒントの目次
3. ADTRAN NetVanta 1224Rデバイスの基本機能を使うにあたってのヒント。 ADTRAN NetVanta 1224Rのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。ADTRAN NetVanta 1224Rに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるADTRAN NetVanta 1224Rのメーカー/サービスへの連絡先に関する情報。

ADTRAN NetVanta 1224Rについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもADTRAN NetVanta 1224Rの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがADTRAN NetVanta 1224Rで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)