Clarion MS8200の取扱説明書

30ページ 0.31 mb
ダウンロード

ページに移動 of 30

Summary
  • Clarion MS8200 - page 1

    installation_rev3.qxd 7/26/99 6:07 PM Page 1 ...

  • Clarion MS8200 - page 2

    1. Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Installation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 3. Mounting Components Main Unit . . . . . . . . . . . . . . . . . ...

  • Clarion MS8200 - page 3

    MS8200 / MS8300 Installation Manual - Page 1 1. Be sure to read the manual thoroughly before beginning the installation to ensure a proper understanding of the MS8200 / MS8300 and its functions. 2. V erify system contents: ❑ Main Unit ❑ T wo 3-Button Remote Transmitters ❑ Siren ❑ Logic Sensor II ❑ Harnesses • 18-Pin main harness • 4-P ...

  • Clarion MS8200 - page 4

    Page 2 - MS8200 / MS8300 Installation Manual 1. Use a V olt / Ohm meter to test all wires. Do not use a test light. 2. Good power and ground connections are essential for proper operation. 3. Route all wires from the engine compartment to the interior of the vehicle through a grommet and use electrical tape and split loom tubing for protection. 4. ...

  • Clarion MS8200 - page 5

    MS8200 / MS8300 Installation Manual - Page 3 Main Unit The main unit should be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. For maximum security , avoid mounting the main unit where it will be easily accessible to a thief. If you are mounting the unit under the dash board, be sure to mount the unit a ...

  • Clarion MS8200 - page 6

    Extended Range Antenna (MS8300) Mount the extended range antenna to the front windshield behind the rear view mirror for best operation. Be sure that this area is clean and free of any metallic window tint film. In certain vehicles such as those equipped with a heated windshield or a built-in windshield defroster , the antenna should be mounted on ...

  • Clarion MS8200 - page 7

    Override Switch Mount the Override Switch in a location near the driver where it is easily accessible but not plainly visible. Plug the blue override switch connector into the blue 2-pin socket on the main unit. Be sure that the switch cannot accidentally be pressed or damaged by movement of passengers or contents within the vehicle. LED Status Ind ...

  • Clarion MS8200 - page 8

    Space Shield III (MS8300) Mount the Space Shield III facing upward in a central location within the vehicle. For optimum performance, avoid mounting the sensor under or facing metal objects or support structures as they will alter the shape of the sensor ’s protection zones. Also, be sure to mount the sensor in a location where items such as coin ...

  • Clarion MS8200 - page 9

    MS8200 / MS8300 Installation Manual - Page 7 Extended Range Antenna (MS8300) Plug the Extended Range Antenna into the connector at the to of the Main unit and wrap antenna wire around Extended Range Antenna cable to prevent interference. Pin 4 - Violet/yellow: Warn A way (-) input Pin 1 - Red: Sensor power +12v output Pin 3 - White/violet: Optional ...

  • Clarion MS8200 - page 10

    Page 8 - MS8200 / MS8300 Installation Manual 18-Pin Main Harness Pin 1 - BLACK: Ground. Connect to a solid chassis ground. Be sure to use a ring connector of proper size. Scrape away the paint at the grounding point. Pin 2 - YELLOW: Door T rigger (+12v) input Connect to positive door switch circuit. This circuit, commonly found in Ford vehicles, wi ...

  • Clarion MS8200 - page 11

    MS8200 / MS8300 Installation Manual - Page 9 Pin 6 - WHITE: Door T rigger (-) input Connect to negative door switch circuit. This circuit will show ground (-) when the door is open. Pin 7 - YELLOW/green: Auxiliary Function 4 (-) output Provides a negative output to activate a relay . The wire provides output for as long as the transmitter button is ...

  • Clarion MS8200 - page 12

    Page 10 - MS8200 / MS8300 Installation Manual When latched or timed operation is selected, the output will reset (turn off) each time the system is armed or disarmed. Pin 15 - ORANGE/blue: Alarming / Horn Honk (-) output Provides a negative output when the system is triggered to activate a relay . The output is selectable for continuous or pulsed o ...

  • Clarion MS8200 - page 13

    3-Pin Door Lock Harness Pin 1 - WHITE/green: Door Lock (-) / Door Unlock (+) Pin 2 - **not used** Pin 3 - WHITE/blue: Door Unlock (-) / Door Lock (+) These wires can be directly connected to negative and positive triggered door lock systems. For V oltage Reversal systems and After-market actuators, add relays. For further information, see Door Lock ...

  • Clarion MS8200 - page 14

    Page 12 - MS8200 / MS8300 Installation Manual Jumper Selections Cancel Auto Rearm. Disables the Automatic Rearm Feature. On = Auto Rearm Disabled Off = Auto Rearm Enabled Parking Light Polarity . Selects the polarity (+/-) for the output of the on-board Parking Light relay . Pin 1 + Pin 2 = positive Pin 2 + Pin 3 = negative Dome Light Polarity . Se ...

  • Clarion MS8200 - page 15

    MS8200 / MS8300 Installation Manual - Page 13 Accessing the Jumpers and Switches Using a flathead screwdriver , carefully press in on the access tabs on the sides of the case until the hooks release. T ake care not to push the tabs in too far or they may break. Once you have made your selections, close the case by aligning the top and button halves ...

  • Clarion MS8200 - page 16

    Page 14 - MS8200 / MS8300 Installation Manual Using the Remote T ransmitters Each system comes with 2 Remote T ransmitters, pre-programmed to Arm and Disarm the system with chirp confirmation using Button 1 . The Mode Button will change function of both Button 1 and Button 2 each time it is pressed. When the Arm/Disarm Button is pressed together wi ...

  • Clarion MS8200 - page 17

    during Programming, Logic Sensor II Adjustment, Space Shield III Adjustment, Real T ime System V erification or any other system set-up function. The Buttons used to control those features will remain as they are described in this manual, regardless of how the T ransmitter is set up to arm and disarm the system. T wo Car Operation T o use a single ...

  • Clarion MS8200 - page 18

    Adding a New T ransmitter into the System 1. T urn on the ignition. 2. Press and hold the Override switch. • The status LED will turn on red. 3. Within 5 seconds: Continue holding the Override switch and Press T ransmitter Button 1* For remote arming with chirp confirmation. --- or --- Release the Override switch and Press T ransmitter Button 1* ...

  • Clarion MS8200 - page 19

    MS8200 / MS8300 Installation Manual - Page 17 System Initialization and Default Reset Following this procedure will set all System Programming Parameters to factory default settings. 1. T urn on ignition. 2. After 4 seconds, press and hold Buttons 1 and 2 together for 5 seconds. The siren will emit one long chirp, indicating that the reset signal w ...

  • Clarion MS8200 - page 20

    Programmable System Parameters 1. Ignition Controlled Door Locking / Unlocking. Selects whether or not the system automatically locks the doors when the ignition is turned on. When selected, the Ignition Controlled Door Locking feature will automatically lock the doors 10 seconds after the ignition key is turned on and automatically unlock the door ...

  • Clarion MS8200 - page 21

    • After 5 seconds, the T ransmitter ’ s LED will begin to flash rapidly , indicating the signal to turn off the Logic Sensor II is being transmitted. • The siren will emit three chirps confirming the signal has been received and will ignore the Logic Sensor II until next time the system is armed. 4. Audible T amper Alert Report. When Audible ...

  • Clarion MS8200 - page 22

    10. Auxiliary Function 2 - Momentary / Latched / Timed Operation. (resets with arm and disarm) Selects between Momentary , Latched, or Timed output for Aux. 2. When Momentary operation is selected, the system will provide an output for as long as the T ransmitter button is held. When Latched operation is selected, the system will provide an output ...

  • Clarion MS8200 - page 23

    MS8200 / MS8300 Installation Manual - Page 21 Because of its advanced design, the Logic Sensor II can be set for Shock and Motion detection or Shock detection only , simply by the way the sensor is mounted. See Mounting Components. Adjustment The shock and motion sensitivity of the Logic Sensor II are set independently , using the Remote T ransmitt ...

  • Clarion MS8200 - page 24

    Page 22 - MS8200 / MS8300 Installation Manual The Space Shield III is a dual zone proximity sensor that uses high frequency radar signals to detect the presence of moving objects within a defined area. For more information, see Mounting Components . Operation While the system is armed, each time the Space Shield III detects movement in the Exterior ...

  • Clarion MS8200 - page 25

    When the minimum or maximum sensitivity levels have been reached, the siren will emit 4 quick chirps. 5. Once you are satisfied with the Interior zone sensitivity setting, press the Mode Button, then Button 2 to begin adjusting the Exterior zone. • The siren will chirp 4 times, the Exterior zone can be adjusted. 6. T est the Exterior zone sensiti ...

  • Clarion MS8200 - page 26

    Page 24 - MS8200 / MS8300 Installation Manual This feature allows the installer to quickly and effectively check all aspects of the installation. T o enter Real T ime System V erification: 1. Enter the vehicle. 2. Close the vehicle doors, hood, and trunk. 3. T urn on the ignition. 4. Within 4 seconds, press the Mode button then press and hold Butto ...

  • Clarion MS8200 - page 27

    MS8200 / MS8300 Installation Manual - Page 25 • During output testing, each function will stay active for as long as the transmitter button is held. After you have finished testing, turn off the ignition key to exit Real T ime Installation V erification. Starter Defeat Override Switch Sensor Kill Wire Hood/T runk Input Door Optional Sensor Input ...

  • Clarion MS8200 - page 28

    Page 26 - MS8200 / MS8300 Installation Manual This feature allows you to recall, from the system ’ s memory , the events (zones) that have triggered the system during the last seven times the system was armed. This is especially useful in diagnosing sensors that are causing the system to trigger and need adjustment. T o enter T rigger History: 1. ...

  • Clarion MS8200 - page 29

    MS8200 / MS8300 Installation Manual - Page 27 Door Lock Diagrams Negative T rigger Positive T rigger V oltage Reversal Aftermarket Actuators V acuum Lock System White/green = (-) Lock / +12v Unlock White/blue = +12v Lock / (-) Unlock installation_rev3.qxd 7/26/99 6:07 PM Page 27 ...

  • Clarion MS8200 - page 30

    Ungo Security Corporation A Clarion Company 661 West Redondo Beach Blvd. Gardena, CA 90247 800-Go-Clarion www .clarionmultimedia © Ungo Security Corporation, Gardena, CA 98-MS8200-00 Rev . 2 (12/97) MS8200 / MS 8300 Wiring Diagram Pin 4 - Violet/yellow: Warn A way (-) input Pin 1 - Red: Sensor power +12v output Pin 3 - White/violet: Optional Senso ...

メーカー Clarion カテゴリー Home Security System

Clarion MS8200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MS8200の取扱説明書
- Clarionの製品カード
- パンフレット
- またはClarion MS8200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Clarion MS8200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Clarion MS8200の取り付け説明書、サービスマニュアル、簡易説明書、またはClarion MS8200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Clarion MS8200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Clarion MS8200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがClarion MS8200を使用するのを助ける技術的文書のことです。説明書は通常、全てのClarion MS8200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Clarionの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Clarion MS8200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははClarion MS8200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Clarion MS8200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Clarion MS8200デバイスの基本機能を使うにあたってのヒント。 Clarion MS8200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Clarion MS8200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるClarion MS8200のメーカー/サービスへの連絡先に関する情報。

Clarion MS8200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもClarion MS8200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがClarion MS8200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)